Search Results (16)

This study explores a novel method for removing Al metal coatings by using nanosecond pulsed lasers to clean Al metal layers from ceramic substrate surfaces. The impact of laser power and pulse width on the effectiveness of the removal of the Al metal layer from the ceramic substrate was examined. The findings revealed that a laser with a power of 120 W, a pulse width of 200 ns, a frequency of 240 kHz, and a speed of 6000 mm/s could effectively remove the Al metal layer (50 μm) in a single laser cleaning cycle without causing damage to the ceramic substrate. The mechanism behind the removal of the Al metal layer from the ceramic substrate surface was also investigated. It was discovered that local high temperatures caused by laser irradiation and the difference in thermal expansion coefficients between the metal layer and the ceramic substrate both contribute to the removal of the Al metal layer during the laser cleaning process. This research provides an effective process for removing the Al metal layer. Full article

Nanosecond laser ablation effectively modifies Cu-ETP copper surfaces by controlling wettability and microstructure. This study examines the effects of nanosecond fiber laser processing and subsequent oxidation on surface evolution. The analyzed parameters include fluence (25.46–1018.59 J/cm²), wavelength (1064 nm), repetition rate (25–1000 kHz), and pulse duration (2–500 ns). To investigate high energy densities, fluence values were set above typical ablation thresholds, inducing hierarchical surface structures affecting wettability. Post-ablation oxidation was examined under two conditions: natural oxidation in ambient air and accelerated oxidation via low-temperature annealing (200 °C) in air. Contact angle measurements revealed that over time, the initially hydrophilic (θ < 90°) laser-textured surfaces exhibited a transition toward hydrophobicity (θ > 90°), which can be attributed to the adsorption of airborne organic compounds rather than oxidation alone. In contrast, annealing significantly accelerated hydrophobicity, attributed to controlled copper oxide growth. SEM and EDS analyses confirmed that higher fluences enhanced roughness and oxidation, forming multi-scale textures and oxide layers, which influenced water repellency. These findings demonstrate that high-fluence laser ablation, combined with controlled oxidation, enables precise wettability engineering. This method provides an efficient strategy for tuning surface properties, offering potential applications in anti-corrosion coatings, self-cleaning surfaces, and heat exchangers, where hydrophobicity and durability are essential. Full article

This study examines the wettability behaviour of 304 stainless steel (304SS) and Ti-6Al-4V (Ti64) surfaces after sequential nanosecond (ns) and picosecond (ps) laser texturing; in particular, how the multi-scale surface structures created influence the lifecycle of surface hydrophobicity. The effect of different post-process treatments is also examined. Surfaces were analysed using Scanning Electron Microscopy (SEM), a white light interferometer optical profiler, and Energy Dispersive X-ray (EDX) spectroscopy. Wettability was assessed through sessile drop contact angle (CA) measurements, conducted at regular intervals over periods of up to 12 months, while EDX scans monitored elemental chemical changes. The results show that sequential (ns + ps) laser processing produced multi-scale surface texture with laser-induced periodic surface structures (LIPSS). Compared to the ns laser case, the (ns + ps) laser processed surfaces transitioned more rapidly to a hydrophobic state and maintained this property for much longer, especially when the single post-process treatment was ultrasonic cleaning. Some interesting features in CA development over these extended timescales are revealed. For 304SS, hydrophobicity was reached in 1–2 days, with the CA then remaining in the range of 120 to 140° for up to 180 days; whereas the ns laser-processed surfaces took longer to reach hydrophobicity and only maintained the condition for up to 30 days. Similar results were found for the case of Ti64. The findings show that such multi-scale structured metal surfaces can offer relatively stable hydrophobic properties, the lifetime of which can be extended significantly through the appropriate selection of laser process parameters and post-process treatment. The addition of LIPSS appears to help extend the longevity of the hydrophobic property. In seeking to identify other factors influencing wettability, from our EDX results, we observed a significant and steady rate of increase in the carbon content at the surface over the study period. Full article

In this study, a pulsed laser operating at a wavelength of 1064 nm and with a pulse width of 100 ns was utilized for the removal of paint from the surface of a 2024 aluminum alloy. The experimental investigation was conducted to analyze the influence of laser parameters on the efficacy of paint layer removal from the aircraft skin’s surface and the subsequent evolution in the microstructure of the laser-treated aluminum alloy substrate. The mechanism underlying laser cleaning was explored through simulation. The findings revealed that power density and scanning speed significantly affected the quality of cleaning. Notably, there were discernible damage thresholds and optimal cleaning parameters in repetitive frequency, with a power density of 178.25 MW/cm², scanning speed of 500 mm/s, and repetitive frequency of 40 kHz identified as the primary optimal settings for achieving the desired cleaning effect. Thermal ablation and thermal vibration were identified as the principal mechanisms of cleaning. Moreover, laser processing induced surface dislocations and concentrated stress, accompanied by grain refinement, on the aluminum substrate. Full article

In this paper, we develop a kW-level high-repetition-rate nanosecond master oscillator power amplifier (MOPA) laser system, employing a structure of fiber, Nd:YVO₄, and Nd:YAG hybrid amplification. A tunable fiber seed source is used for adjustable pulse repetition frequency and pulse width. The Nd:YVO₄ pre-amplifier, which is dual-end-pumped, achieves high gain while maintaining good beam quality, and the high-power side-pumped Nd:YAG slab main-amplifier enables efficient power amplification. The repetition rate of the output laser can be adjusted within the range of 1~20 kHz, and the pulse width can be tuned within the range of 10~300 ns. The seed output is 6 mW at a repetition frequency of 20 kHz; we achieve an average output power of 1240 W with a total power extraction efficiency of 39.1% and single-pulse energy of 62 mJ at a pulse width of 301 ns. This parameter-controllable high-power laser holds promise for applications in the laser cleaning of complex surface contaminants. Full article

Nuclear power components contain radioactivity on their surfaces after long-term service, which can be harmful to personnel and the environment during maintenance, dismantling, and decommissioning. In this experiment, laser decontamination technology is utilized to remove radioactivity from their surfaces. In order to meet the actual needs, a laser decontamination process without spot overlapping has been studied. Under the same equipment conditions, the decontamination efficiency of the non-spot overlapping process is 10 times higher than that of the spot overlapping process. Alloy 690 is used as the test substrate, and non-radioactive specimens are prepared by simulating primary-circuit hydrochemical conditions. The surface morphology, elemental composition, and phase composition of the specimens before and after laser decontamination are investigated with SEM and XRD using the single-pulse experiment and power single-factor experiment methods, and the laser decontamination effect was evaluated. The results show that the decontamination efficiency reached 10.8 m²/h under the conditions of a pulse width of 500 ns, a laser repetition frequency of 40 kHz, a scanning speed of 15,000 mm/s, and a line spacing of 0.2 mm, according to which the removal effect was achieved when the laser power was 160 W and the oxygen content on the surface was 6.29%; additionally, there were no oxide phases in the XRD spectra after decontamination. Therefore, the laser cleaning process without spot overlap can provide reference for future practical operations to achieve efficient removal of radioactivity from nuclear power components. Full article

We report, for the first time, the generation of a 1173 nm acousto-optic Q-switched self-Raman vortex laser with an axicon-based annular pump system. A 20 mm long Nd:GdVO₄ crystal was used as the self-Raman crystal. Both the fundamental field and the first-Stokes field were investigated using the respective output couplers. In comparison with both vortex fields, a noticeable beam cleaning-up effect and pulse compression were observed from the 1063 nm fundamental field to the 1173 nm first-Stokes field. A Stokes field carrying a unitary topological charge was achieved. Finally, the average output power of the first-Stokes vortex emission reached 454 mW under an incident pump power of 19.5 W, corresponding to a pulse width of 45.7 ns. It was beneficial to apply a high peak power from the Q-switched laser and self-Raman conversion to expand the applications of the vortex laser beam. Full article

Varnish removal from easel paintings is a restoration procedure that is regularly undertaken by cultural heritage conservators. In very few cases, traditional methods (chemical and mechanical) do not allow them to reach the goal of a perfectly controlled and selective cleaning. UV laser ablation has been considered since the 1990s to overcome these limitations, but its application to real cases is far from common practice. This study proposes a calibrated procedure based on ablation by an ns UV Nd:YAG laser at 266 nm combined with optical coherence tomography for micrometric laser varnish removal from inhomogeneous and highly photosensitive pictorial layers. The use of this wavelength for varnish removal, not adapted according to the literature, is discussed again after the beam shaping leading to a homogeneous and controlled intensity distribution. The innocuity is controlled by laser-induced luminescence, and some solutions for the transparency loss of the residual varnish following ablation are proposed. Full article

In this work lasers with micro-, nano-, pico- and femtosecond pulse durations were used to clean atmospheric corrosion products from the fragments of a 19th-century lead outdoor sculpture. The state of the surface was studied by optical microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and scanning electron microscopy. It was shown that for all lasers used there is no self-limiting cleaning effect, and the metal damage threshold is lower than the corrosion removal threshold. Using the XPS method, it has been demonstrated that the effect of turning a metallic lead surface blue after irradiation is associated with an interference effect in the PbO film. Raman spectroscopy indicated no phase changes in the corrosion layer after laser cleaning with 8 ns, 75 ps and 100 fs pulses, which makes these lasers useful for the layer-by-layer cleaning of archaeological objects. Full article

Shipyards are very interested in improving their working environment and resolving environmental pollution issues by replacing mechanical cleaning technologies used before and after painting processes with laser cleaning technology. Because epoxy paint is thickly coated, with a thickness of 200 μm or greater, it is difficult to remove using both laser cleaning and mechanical cleaning technologies. Therefore, this study tried to obtain effective cleaning results by controlling the process parameters when removing the thick epoxy coating using a Q-switching fiber laser cleaning system with an average power of 100 W developed by our research team. The pulse duration time of the laser is 150 ns. Additionally, in order to determine whether the cleaning was sufficient, the difference in laser-induced plume/plasma was compared. By controlling the beam scanning patterns, line overlap rate, and pulse overlap rate, it was possible to obtain effective cleaning results without introducing removal deviation. In addition, the NOP increased when the laser beam overlap rate increased. This increased the amount of heat input to the material and reduced the number of scans required to remove the epoxy paint. As a result of the plume/plasma analysis, less plume/plasma was generated as the paint was removed if the epoxy paint remained on the surface. On the other hand, when all of the paint was removed, a higher brightness of plume/plasma generated by evaporation of the bare metal was observed. Full article

Substrate cleaning prior to coating has a strong influence on the performance of the optical component. Exemplary, none or inadequate cleaning reduces the resistance against laser irradiation drastically. Especially in laser components coated with anti-reflective layers, the interface between substrate and coating is one of the most limiting factors. This study investigates different precision cleaning processes and their influence on the laser resistance of ion-beam sputtered anti-reflective coatings. Therefore, a SiO₂/Ta₂O₅ multilayer anti-reflective coating for a wavelength of 1064 nm and a normal angle of incidence was deposited onto high-quality fused silica substrates. Prior to deposition, the substrates were cleaned with various cleaning processes using different solutions and ultrasonic frequencies. To characterize the cleaned surface quality, the surfaces were analyzed with respect to root-mean-square (RMS) roughness and particle density. Laser damage was measured using a 1064 nm ns-pulsed laser test bench. It was found that an alcoholic pre-clean is recommendable to prevent laser damage caused by organic films remaining from the polishing process. The applied ultrasonic frequencies strongly influenced the particle density down to the sub-micrometer range and in consequence, the laser-induced damage threshold (LIDT). Ultrasonic cleaning at excessive power levels can reduce laser resistance. Full article

The removal of the surface paint of Q345 (Gr·B) steel, as well as microstructure and hardness of the cleaned surface were investigated. The laser source used in this study is a nanosecond pulsed Gaussian light source. The surface morphology and microstructure were characterized by a scanning electron microscope and electron back-scattered diffraction. A hardness test was used for capturing variations of the parameter of the cleaned region in comparison to the base metal. The results show that when the X-scanning speed was 1500 mm/s and Y-moving speeds was 7 mm/s during ns-laser cleaning, respectively, the cleaned surface was relatively flat and there was only a few small residual paint. In addition, the contents of Fe and C elements on the cleaned surface reached to 89% and 9%, respectively. Moreover, the roughness was the lowest of 0.5 μm through the observation of the three-dimensional topography. In addition, a fine grain layer appeared on the cleaned surface after laser cleaning at the X-scanning speeds of 500 mm/s and 1000 mm/s. The maximum hardness of the fine grain layer was more than 400 HV, higher than the base metal. Full article

As a common mechanical material for mining machinery, Q345 is prone to oxidation due to the moist working environment. At present, laser cleaning is often used to remove rust oxides from the substrate. The pollutant of mining machinery is comprised of a heavy oxide layer and organic ingredients, which are difficult to remove and require high energy per pulse. However, excessive energy is capable of easily destroying surface integrity, such as increasing surface roughness (R_a), generating ablative pits, oxidizing, decreasing microhardness (HV), and decreasing corrosion resistance. Therefore, this paper focused on investigating the surface integrity of mining parts under different laser powers, repetition rates and overlapping rates of the laser spots. The results showed that the surface integrity of the samples gradually improved as the energy per pulse and overlapping rates increased. However, excessive energy caused a negative effect on surface integrity. Based on the comprehensive analysis, optimal parameters were obtained when the power was 280 W, the repetition rate was 10 kHz (pulse duration 84 ns), and the overlapping rate of the laser spot was 70%. This work can provide theoretical guidance for the laser cleaning of mining machinery. Full article

Peri-implantitis (PI) is an inflammatory disease of peri-implant tissues, it represents the most frequent complication of dental implants. Evidence revealed that microorganisms play the chief role in causing PI. The purpose of our study is to evaluate the cleaning of contaminated dental implant surfaces by means of the Q-switch Nd:YAG (Neodymium-doped Yttrium Aluminum Garnet) laser and an increase in temperature at lased implant surfaces during the cleaning process. Seventy-eight implants (titanium grade 4) were used (Euroteknika, Sallanches, France). Thirty-six sterile implants and forty-two contaminated implants were collected from failed clinical implants for different reasons, independent from the study. Thirty-six contaminated implants were partially irradiated by Q-switch Nd:YAG laser (1064 nm). Six other contaminated implants were used for temperature rise evaluation. All laser irradiations were calibrated by means of a powermetter in order to evaluate the effective delivered energy. The irradiation conditions delivered per pulse on the target were effectively: energy density per pulse of 0.597 J/cm², pick powers density of 56 mW/cm², 270 mW per pulse with a spot diameter of 2.4 mm, and with repetition rate of 10 Hz for pulse duration of 6 ns. Irradiation was performed during a total time of 2 s in a non-contact mode at a distance of 0.5 mm from implant surfaces. The parameters were chosen according to the results of a theoretical modeling calculation of the Nd:YAG laser fluency on implant surface. Evaluation of contaminants removal showed that the cleaning of the irradiated implant surfaces was statistically similar to those of sterile implants (p-value ≤ 0.05). SEM analysis confirmed that our parameters did not alter the lased surfaces. The increase in temperature generated at lased implant surfaces during cleaning was below 1 °C. According to our findings, Q-switch Nd:YAG laser with short pulse duration in nanoseconds is able to significantly clean contaminated implant surfaces. Irradiation parameters used in our study can be considered safe for periodontal tissue. Full article

Controlling the surface wettability represents an important challenge in the field of surface functionalization. Here, the wettability of a stainless-steel surface is modified by 30-ns pulses of a Nd:YAG marking laser (λ = 1064 nm) with peak fluences within the range 3.3–25.1 J cm⁻². The short- (40 days), intermediate- (100 days) and long-term (1 year) superhydrophilic-to-(super)hydrophobic transition of the laser-textured surfaces exposed to the atmospheric air is examined by evaluating its wettability in the context of the following parameters: (i) pulse fluence; (ii) scan line separation; (iii) focal position and (iv) wetting period due to contact angle measurements. The results show that using solely a short-term evaluation can lead to wrong conclusions and that the faster development of the hydrophobicity immediately after laser texturing usually leads to lower final contact angle and vice versa, the slower this transition is, the more superhydrophobic the surface is expected to become (possibly even with self-cleaning ability). Depending on laser fluence, the laser-textured surfaces can develop stable or unstable hydrophobicity. Stable hydrophobicity is achieved, if the threshold fluence of 12 J cm⁻² is exceeded. We show that by nanosecond-laser texturing a lotus-leaf-like surface with a contact angle above 150° and roll-off angle below 5° can be achieved. Full article