Search Results (7)

Direct upgrading of methane into value-added products is one of the most significant technologies for the effective transformation of hydrocarbon feedstocks in the chemical industry. Both oxidative and non-oxidative methane conversion are broadly useful approaches, though the two reaction pathways are quite distinguished. Oxidative coupling of methane (OCM) has been widely studied, but suffers from the low selectivity to C₂ hydrocarbons because of the overoxidation leading to undesired byproducts. Therefore, non-oxidative coupling of methane is a worthy alternative approach to be developed for the efficient, direct utilization of methane. Recently, heterogeneous catalysts comprising singly dispersed metal sites, such as single-atom catalysts (SAC) and surface organometallic catalysts (SOMCat), have been proven to be effectively active for direct coupling of methane to product hydrogen and C₂ products. In this context, this review summarizes recent discoveries of these novel catalysts and provides a perspective on promising catalytic processes for methane transformation via non-oxidative coupling. Full article

The characteristics of active sites on the surface of albite were theoretically analyzed by density functional theory, and the activation of the C-H bond of methane using an albite catalyst and the reaction mechanism of preparing C₂ hydrocarbons by nonoxidative coupling were studied. There are two frustrated Lewis pairs (FLPs) on the (001) and (010) surfaces of albite; they can dissociate H₂ under mild conditions and show high activity for the activation of methane C-H bonds. CH₄ molecules can undergo direct dissociative adsorption on the (010) surface, whereas a 50.07 kJ/mol activation barrier is needed on the (001) surface. The prepared albite catalyst has a double combination function of the (001) and (010) surfaces; these surfaces produce a spillover phenomenon in the process of CH₄ activation reactions, where CH₃ overflows from the (001) surface with CH₃ adsorbed on the (010) surface to achieve nonoxidative high efficiently C-C coupling with an activation energy of 18.51 kJ/mol. At the same time, this spillover phenomenon inhibits deep dehydrogenation, which is conducive to the selectivity of the C₂ hydrocarbons. The experimental results confirm that the selectivity of the C₂ hydrocarbons is maintained above 99% in the temperature range of 873 K to 1173 K. Full article

This study describes the distribution of arsenic mobile species in the tailings of Cu–Co–Ni–arsenide using the sequential extraction and determining the contents of arsenate (As^V) and arsenite (As^III). The object of this study is the tailings ponds of the Tuvakobalt plant, which contains waste from the hydrometallurgical arsenide ore processing of the Khovu-Aksy deposit (Republic of Tuva, Russia). A procedure of sequential extraction for arsenic was applied, and it includes the extraction of the following forms: water-soluble, potentially water-soluble and exchangeable, easily sorbed on the surface of carbonates, associated with Fe/Mn oxides/hydroxides, associated with easily oxidized minerals, and accounted for by non-oxidized arsenic minerals. This procedure, which takes into account the peculiarities of the physical and chemical composition of the waste, was supplemented by the analytical determination of the arsenite and arsenate content by using the methods of inductively coupled plasma atomic emission spectrometry (ICP-AES) combined with the hydride generation technique (HG-ICP-AES). The content of the most mobile forms of arsenic, which are water-soluble, potentially water-soluble, and exchangeable species, is equal to 56% of the total arsenic content, 23% and 33% of which are arsenite and arsenate, respectively. Unlike arsenic, the mobile forms of metals have been determined in small quantities. The largest proportion of water-soluble and exchangeable forms is formed by Mg, Ca, and Sr at 11, 9.4, and 20%, respectively (residual and redeposited carbonates). The proportion of water-soluble forms of other metals (Cu, Zn, Co, and Ni) is < 1% or 0. The main part of the metals is adsorbed on the surface of Fe and Mn hydroxides, enclosed in easily and hardly oxidized minerals. In addition to geochemical studies, the presence of leaks from the tailing ponds into ground waters was determined by using electrical resistivity tomography. The data obtained indicate a high environmental hazard of tailings and the possibility of water-soluble and highly toxic arsenic compounds entering ground waters and aquifers. Full article

The mechanical and tribological characteristics of the Ti-6Al-7Nb alloy were investigated within a wide range of temperature and time parameters of thermal oxidation. The hardness, H_IT, and indentation modulus, E_IT, of the alloy in question, with and without an anti-wear oxide layer, were determined. The tribological properties of sliding couples were studied under technically dry friction conditions, using a ball-on-disc tribometer. The test pieces were non-oxidized and oxidized Ti-6Al-7Nb alloy discs, and Al₂O₃, ZrO_2, and 100Cr6 balls were used as counter specimens. After thermal oxidation, the surface of the titanium alloy was characterized by a significantly higher hardness, H_IT (8–10 GPa), compared to the surface not covered with oxide layers (3.6 GPa). The study showed that the curvature of the loading segments increased with an increasing oxidation temperature, indicating a strong positive dependence of hardness on the thermal oxidation temperature. The value of the indentation modulus, E_IT, was also found to increase with the increasing oxidation temperature. The intensity of the tribological processes was strictly dependent on the oxidation parameters and the couple’s material (Al₂O₃, ZrO₂, 100Cr6). It has been shown that the thermal oxidation process makes it possible to control, within a wide range, the friction-wear characteristics of the Ti-6Al-7Nb alloy. Full article

Photocatalytic processes are being studied extensively as potential advanced wastewater treatments for the removal of pharmaceuticals, pesticides and other recalcitrant micropollutants from the effluents of conventional wastewater treatment plants (WWTPs). Oxytetracycline (OTC) is a widespread antibiotic which is frequently detected in surface water bodies as a recalcitrant and persistent micropollutant. This review provides an update on advances in heterogeneous photocatalysis for the degradation of OTC in water under UV light, sunlight and visible-light irradiation. Photocatalysts based on pure semiconducting oxides are rarely used, due to the problem of rapid recombination of electron–hole pairs. To overcome this issue, a good strategy could be the coupling of two different semiconducting compounds with different conduction and valence bands. Several methods are described to enhance the performances of catalysts, such as doping of the oxide with metal and/or non-metal elements, surface functionalization, composites and nano-heterojunction. Furthermore, a discussion on non-oxidic photocatalysts is briefly provided, focusing on the application of graphene-based nanocomposites for the effective treatment of OTC. Full article

The purpose of the present study was to compare the wear behavior of ceramic-on-vitamin-E-diffused crosslinked polyethylene (Vit-E XLPE) hip bearings employing the gold standard oxide ceramic, zirconia (ZrO₂)-toughened alumina (Al₂O₃) (ZTA, BIOLOX^®delta) and a new non-oxide ceramic, silicon nitride (Si₃N₄, MC^2®). In vitro wear test was performed using a 12-station hip joint simulator. The test was carried out by applying the kinematic inputs and outputs as recommended by ISO 14242-1:2012. Vitamin-E-diffused crosslinked polyethylene (Vit-E XLPE) acetabular liners (E1^®) were coupled with Ø28-mm ZTA and Si₃N₄ femoral heads. XLPE liner weight loss over 5 million cycles (Mc) of testing was compared between the two different bearing couples. Surface topography, phase contents, and residual stresses were analyzed by contact profilometer and Raman microspectroscopy. Vit-E XLPE liners coupled with Si₃N₄ heads produced slightly lower wear rates than identical liners with ZTA heads. The mean wear rates (corrected for fluid absorption) of liners coupled with ZTA and Si₃N₄ heads were 0.53 ± 0.24 and 0.49 ± 0.23 mg/Mc after 5 Mc of simulated gait, respectively. However, after wear testing, the ZTA heads retained a smoother topography and showed fewer surface stresses than the Si₃N₄ ones. Note that no statistically significant differences were found in the above comparisons. This study suggests that the tribochemically formed soft silica layer on the Si₃N₄ heads may have reduced friction and slightly lowered the wear of the Vit-E XLPE liners. Considering also that the toughness of Si₃N₄ is superior to ZTA, the present wear data represent positive news in the future development of long-lasting hip components. Full article

In this study, the PPS/MWCNTs/AlN composite was prepared with poly(phenylene sulfide) (PPS), covalent functionalized multi-walled carbon nanotubes (fMWCNTs), and aluminum nitride (AlN) via melt-blending techniques. The AlN is a fascinating non-oxidizing ceramic material having the highest thermal conductivity among the ceramic materials. In order to introduce the functional groups on the surface of the AlN particles, a silane coupling agent was used as it is able to graft with the functional groups on the covalent functionalized MWCNTs. The silanization reaction of the AlN was confirmed qualitatively and quantitatively by FT-IR (Fourier Transform Infrared Spectroscopy), and XPS (X-ray Photoelectron Spectroscopy). The grafting reaction of the AlN particles on the MWCNTs was confirmed using UV–Vis (Ultraviolet-Visible Spectroscopy), FE-SEM (Field-Emission Scanning Electron Microscopy) and FE-TEM (Field-Emission Transmission Electron Microscopy) images. The grafting reaction was accomplished by observing the change of the transmittance, the morphology of the AlN particle bonded to the MWCNTs. For the morphological changes of the fractured surface of the PPS/MWCNTs/AlN composites by FE-SEM, the hybrid filler was homogeneously dispersed on the PPS matrix when the AlN particle was grafted on the MWCNTs. The homogeneous distribution of the hybrid filler acts as a heat transfer path, which led the higher thermal properties, such as thermal conductivity, thermal resistance, and melting temperature than those of not grafted MWCNTs. Full article