Search Results (276)

The development of low-cost and high-efficiency oxygen evolution reaction (OER) catalysts is essential to enhance the practicality of electrochemical water splitting for green hydrogen production. Layered double hydroxides (LDHs), especially those based on nickel and cobalt, have attracted attention due to their tunable composition, abundant redox-active sites, and earth-abundant constituents. However, their application is hindered by their limited conductivity and sluggish reaction kinetics. In this study, rare-earth-element-doped NiCo LDHs were synthesized directly on nickel foam through a one-step hydrothermal approach to improve the OER activity by modulating the electronic structure and optimizing the surface morphology. Among the representative catalysts, the incorporation of Sm significantly influenced the microstructure and electronic configuration of the catalyst, as confirmed by X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Electrochemical tests showed that the optimized Sm-NiCo LDH achieved a low overpotential of 172 mV at 10 mA cm⁻² and a small Tafel slope of 84 mV dec⁻¹ in 1 M KOH, indicating an expanded electrochemically active surface and improved charge transport. Long-term stability tests further showed its durability. These findings suggest that Sm doping enhances the OER performance by increasing active site exposure and promoting efficient charge transfer, offering a promising strategy for designing rare-earth-modified, non-precious-metal-based OER catalysts. Full article

The effects of trace Ce on the microstructure and texture of non-oriented silicon steel during recrystallization and grain growth were examined using X-ray diffraction and electron backscatter diffraction. Additionally, this study focused on investigating the mechanisms by which trace Ce influences the evolution of the {114} <481> and γ-fiber textures. During the recrystallization process, as the recrystallization fraction of annealed sheets increased, the intensity of α-fiber texture decreased, while the intensities of α*-fiber and γ-fiber textures increased. The {111} <112> grains preferentially nucleated in the deformed γ-grains and their grain-boundary regions and tended to form a colony structure with a large amount of nucleation. In addition, the {100} <012> and {114} <481> grains mainly nucleated near the deformed α-grains, which were evenly distributed but found in relatively small quantities. The hindering effect of trace Ce on dislocation motion in cold-rolled sheets results in a 2–7% lower recrystallization ratio for the annealed sheets, compared to conventional annealed sheets. Trace Ce suppresses the nucleation and growth of γ-grains while creating opportunities for α*-grain nucleation. During grain growth, trace Ce reduces γ-grain-boundary migration rate in annealed sheets, providing growth space for {114} <418> grains. Consequently, the content of the corresponding {114} <481> texture increased by 6.4%, while the γ-fiber texture content decreased by 3.6%. Full article

Rare earth elements (REEs) are emerging soil contaminants due to increasing fertilizer use, mining activities, and technological applications. However, few studies have assessed their concentrations in soils or associated environmental risks. Here, we evaluate the influence of land cover types (Eucalyptus plantation, forest, and pasture), parent material, and soil physicochemical properties (predictor variables) on REE content in the Brazilian Atlantic Forest and measure pseudo-total REE content using inductively coupled plasma mass spectrometry (ICP-MS). Differences in REE content across land cover types, parent materials, and soil properties were assessed using similarity and variance analyses (ANOSIM, ANOVA, and Kruskal–Wallis) followed by post hoc tests (Tukey HSD and Dunn’s). We used model selection based on the Akaike criterion (ΔAICc < 2) to determine the influence of predictor variables on REE content. Our results showed that parent materials (igneous and metamorphic rocks) were the best predictors, yielding plausible models (Adj R² ≥ 0.3) for Y, δEu, and La_N/Sa_N. In contrast, Ca:Mg alone provided a plausible model (Adj R² = 0.15) for δCe anomalies, while clay content (Adj R² = 0.11) influenced the Sa_N/Yb_N ratio, though soil properties had weaker effects than parent materials. However, we found no evidence that Eucalyptus plantations or pastures under non-intensive management increase REE content in Brazilian Atlantic Forest soils. Full article

This study presents a design and optimization methodology to enhance the power density and efficiency of wound field synchronous machines (WFSMs) by selectively applying grain-oriented electrical steel (GOES). Unlike conventional non-grain-oriented electrical steel (NOES), GOES exhibits significantly lower core loss along its rolling direction, making it suitable for regions with predominantly alternating magnetic fields. Based on magnetic field analysis, four machine configurations were investigated, differing in the placement of GOES within stator and rotor teeth. Finite element analysis (FEA) was employed to compare electromagnetic performance across the configurations. Subsequently, a multi-objective optimization was conducted using Latin Hypercube Sampling, meta-modeling, and a genetic algorithm to maximize power density and efficiency while minimizing torque ripple. The optimized WFSM achieved a 13.97% increase in power density and a 1.0% improvement in efficiency compared to the baseline NOES model. These results demonstrate the feasibility of applying GOES in rotating machines to reduce core loss and improve overall performance, offering a viable alternative to rare-earth permanent magnet machines in xEV applications. Full article

Improper emissions from industrial activities pose toxicological risks to groundwater safety. Based on an environmental forensic identification case involving livestock (sheep) damage caused by groundwater pollution in a pastoral area, we comprehensively evaluated groundwater quality risks, toxicological risks, and pollution sources using multivariate statistical methods, the Nemerow index method, and a non-carcinogenic health risk model. The potential specific pollutants in the region mainly included calcium, potassium, sodium, magnesium, manganese, fluoride, chloride, sulfate, ammonia nitrogen, total dissolved solids, and nitrate. An evaluation of the groundwater health risk factors showed that fluoride, nitrate, and manganese pose higher health risks (HQ > 1), as fluoride > nitrate > manganese. This suggests that these three pollutants were the primary causes of livestock damage. Identification of pollution sources using multivariate statistical analysis revealed that the main pollutants in the groundwater originate from two rare earth enterprises in the surrounding industrial park, followed by the emissions from animal husbandry. This study provides guidelines into comprehensive regional toxicological risk assessment and source tracing, offering an identification method for similar forensic environmental damage cases. Full article

Cigarette smoking exposes individuals to numerous toxic substances, including heavy metals. Smokers are at risk due to the accumulation of these substances in various tissues. Objective: To compare the concentrations of 41 elements in 11 brain regions, the spinal cord, the bronchial, the lungs, and the liver in smokers (n = 11) and non-smokers (n = 17). Elemental composition was determined by ICP-MS after wet digestion in a microwave system. The following toxic elements were detected at levels of µg/g w.w.: Al, Cd, Pb, Ba, As, Ni, and Tl. Significantly higher concentrations of Al were detected in bronchial and lung, and more Pb, Tl, and rare earth elements were detected in the liver of smokers compared to non-smokers. In addition, smokers had significantly lower concentrations of essential elements involved in antioxidant defense, such as Cu, in liver tissue (p = 0.033). The brain and spinal cord in smokers and non-smokers were similar in terms of chemical composition, except the insula, where smokers had greater Al accumulation (p = 0.030), the precentral gyrus, where higher amounts of As, Cd, and Mn were detected, and the septal nucleus accumbens, which preferentially accumulated Cd in smokers; however, the p-values indicate that these differences were not statistically significant. Most brain areas of smokers were characterized by higher Na content (p < 0.05). These findings prove the long-term effects of smoking, demonstrating the bioaccumulation of toxic elements, the increased levels of rare earth elements in the liver, decreased levels of elements involved in the body’s antioxidant defense, and disruption of sodium homeostasis in the brain of smokers. Full article

The complex dielectric permittivity has been studied with the waves of millimeter wavelength for rare earth manganate and titanate and LiCoPO₄ and LiNi_0.5Co_0.5PO₄ orthophosphate composites. The measurements are carried out at frequencies of 26 to 38 GHz via measurements of transmission and reflection coefficients through a plate. A special method on how to extract the real and imaginary parts of dielectric permittivity is applied. Discussion is conducted on a nonmonotonic type of the frequency dependences for both real and imaginary parts of permittivity, and it has been shown that relaxation is non-Debye. The Cole–Cole, Havriliak–Negami, and Kohlrausch–Williams–Watts models cannot also explain the nonmonotonic frequency dependence of the real part of dielectric permittivity. Investigation of the structure and phase composition of nanocomposites has been carried out. Full article

Nd–Fe–B permanent magnets are vital for numerous key technologies in strategic sectors such as renewable energy production, e-mobility, defense, and aerospace. Accordingly, the demand for rare earth elements (REEs) enormously increases in parallel to a significant uncertainty in their supply. Thus, research and innovative studies are focus on the investigation of sustainable solutions to the problem and a closed-loop value chain. The present study is based on two benign-by-design approaches aimed at decreasing the recycling loop span by preparing standardized batches of EoL Nd–Fe–B materials to be treated separately depending on their properties, as well as using mechanochemical method for waste processing. The previously reported benefits of both direct recycling and mechanochemistry include significant improvements in processing metrics, such as energy use, ecological impact, technology simplification, and cost reduction. Waste-sintered Nd–Fe–B magnets from motorbikes were collected, precisely sorted, selected, and pre-treated. The study presents a protocol of resource-efficient recycling through mechanochemical processing of non-oxidized sintered EoL magnets, involving the extraction of Nd₂Fe₁₄B magnetic grains and refining the material’s microstructure and particle size after 120 min of high-energy ball milling in a zirconia reactor. The recycled material preserves the main Nd₂Fe₁₄B magnetic phase, while an anisotropic particle shape and formation of a thin Nd/REE-rich layer on the grain surface were achieved. Full article

Red mud from bauxite processing is among the large-tonnage technogenic waste that poses a significant ecological threat. At the same time, red mud serves as a raw material source for expanding the resource base for obtaining iron, rare metals, and rare earth elements. Numerous studies on their utilization have shown that only through comprehensive processing, combining pyrometallurgical and hydrometallurgical methods, is it possible to maximize the extraction of all the useful components. This work addresses the first stage of a comprehensive technology for processing red mud through reduction smelting, separating iron in the form of pig iron, and producing slag. Studies were conducted on the reductive smelting of red mud using waste slurry from alumina production as the calcium-containing material, taken in proportions calculated to obtain a fluid slag with a hydraulic modulus of 0.55–0.8. The permissible mixing range of red mud with waste slurry was determined to be in the ratio of 0.56–1.2. In cases where the charge was prepared in violation of the required hydraulic modulus value, pig iron was not obtained during smelting. When the hydraulic modulus requirement was met, the temperature of the reductive smelting process was 1350–1400 °C. The total amount of recovered iron obtained as pig iron and fine fractions amounted to 99.5% of the original content. The low iron content (0.23–0.31%) in the non-magnetic slag fraction allows for the production of high-quality titanium oxide and rare earth element concentrates in the subsequent stages of the comprehensive hydrometallurgical processing of red mud, involving acid leaching. Based on the results of a phase analysis of the slag, pig iron, and melt, the reactions of the reductive smelting process were established, and their thermodynamic likelihood was determined. In fluid slags, the content of the sodium aluminosilicate phase is twice as high as that in slag with a higher hydraulic modulus. The reductive smelting of 100% red mud with the addition of calcium oxide, calculated to achieve a hydraulic module of 0.55 at a temperature of 1350–1400 °C, produced pig iron and slag with high alkali and iron contents. Full article

The development of effective, cost-efficient, and printable solid-state gas sensors for the detection of volatile organic compounds is of great interest due to their wide range of applications, spanning from real-time indoor monitoring to emerging fields such as non-invasive medical diagnostics. However, gas sensors encounter difficulties in discovering materials that have both good selectivity and sensitivity for numerous volatile organic compounds in both dry and humid settings. To expand the class of sensing materials, the current study investigates the sensing performance of solid solutions based on a rare-earth metal oxide. Pr, Fe, and Ti oxide solid solutions were produced using a solid-state technique, with thermal treatments at varied temperatures to tune their structural and functional properties. The powders were used, for the first time, to produce chemoresistive sensors, which showed promising sensing capabilities vs. ethanol, acetone, and acetaldehyde. The sensors were characterized by varying the concentration of the target gases from 1 to 50 ppm in a controlled environment, with the relative humidity ranging from 2 to 40%. The findings bring a turning point, leading to fruitful paths for the development of Pr-based solid solutions-based chemoresistive gas sensors for the detection of volatile organic compounds. Full article

Rare earth elements (REEs) are critical mineral resources that play a pivotal role in modern technology and industry. Currently, the global supply of light rare earth elements (LREEs) remains adequate. However, the supply of heavy rare earth elements (HREEs) is associated with substantial risks due to their limited availability. Ion-adsorption type rare earth deposits (IAREDs), which represent the predominant source of HREEs, have become a focal point for exploration activities, with a notable increase in global interest in recent years. This study systematically collected stream sediments and stream water samples from the Jiaping IARED in Guangxi, as well as from adjacent granitic and carbonate background areas, to investigate the exploration significance of geochemical surveys for IAREDs. Additionally, mineralized soil layers, non-mineralized soil layers, and bedrock samples from the weathering crust of the Jiaping deposit were analyzed. The results indicate that stream sediments originating from the Jiaping IARED and granite-hosted background regions display substantially elevated REE concentrations relative to those from carbonate-hosted background areas. Moreover, δEu values in stream sediments can serve as an effective indicator for differentiating weathering products derived from granitic and carbonate lithologies. Within the mining area, three coarse-grained fractions of stream sediments (i.e., +20 mesh, 20–60 mesh, and 60–150 mesh) exhibit REE concentrations comparable to those observed in both granite-hosted and carbonate-hosted background regions. However, the HREEs content in the finer -150-mesh stream sediments from Jiaping IARED is markedly higher than that in the two background regions. The (La/Sm)_N versus (La/Yb)_N ratios of -150-mesh stream sediments in the Jiaping IARED may reflect the mixing processes involving HREE-enriched ore layer, non-mineralized layer, and LREE-enriched ore layer. This observation implies that fine-grained (-150-mesh) stream sediments can partially inherit the REE characteristics of mineralized layers within IAREDs. Scanning electron microscopy (SEM) observations indicate that the enrichment of REEs in fine-grained stream sediments primarily originates from REE-rich accessory minerals derived from parent rocks and mineralized weathering crusts. A comparative analysis reveals that the concentrations of REEs in stream water collected during the rainy season are significantly higher than those collected during the dry season. Moreover, the levels of REEs, especially HREE, in stream water from the Jiaping IARED substantially exceed those in background areas. Collectively, these findings suggest that the geochemical signatures of REEs in rainy season stream water possess diagnostic potential for identifying IAREDs. In conclusion, the integrated application of geochemical surveys of stream water and -150-mesh stream sediments can effectively delineate exploration targets for IAREDs. Full article

Rare earth-doped upconversion nanoparticles (UCNPs) can convert low-energy photons (NIRs) into high-energy photons (visible light), offering advantages such as low background signal, good stability, and excellent biocompatibility. However, exploring a strategy to combine the advantages of high efficiency, low cost, and easy fabrication of a plasmonics–UCNPs system is still a challenge. Here, we reported a metal–dielectric–metal (MDM)-type plasmonic platform based on the aluminum metasurface, which can efficiently enhance the luminescence intensity of magnetic and non-magnetic rare earth-doped UCNPs. Attributed to the strong local field effect of the nanocavities formed by the aluminum anti-transmission layer at the bottom, the fluorescence of the two types of UCNPs in such a platform can be enhanced by over 1000 folds compared with that in the conventional substrate. It is found that the deposited UCNPs amount and the aluminum pillar size can both impact the enhancement. We confirmed that the constructed MDM nanocavities could enhance and regulate the local field strength, and the optimum enhancement can be achieved by choosing proper parameters. All these findings provide an efficient way of exploring the plasmon-enhanced UCNPs luminescence system with low cost, high efficiency, and easy fabrication and can be promising in the fields of biosensing and photovoltaic devices. Full article

In this study, a rare 3.49-carat yellow diamond was analyzed to reconstruct the geological processes that led to its distinctive form. The diamond exhibits growth and dissolution features, indicating a complex history. To preserve the sample’s integrity, non-destructive analytical techniques—including VIS, UV–Vis–NIR, and IR spectroscopy—were employed. The yellow coloration of the diamond is attributed to the presence of N3 and N2 defects. Additionally, other defects such as N₃VH⁰ centers and platelets were detected; however, the latter do not contribute to the coloration. The observations of the etch pits and surface microreliefs suggest that the diamond underwent size reduction due to dissolution events, which also altered its crystal habit over time. The diamond’s initial mixed-habit morphology evolved into a more complex one through a series of growth and dissolution processes that began during mantle storage. Furthermore, the presence of brown surface stains indicates radiation damage, likely acquired during its residence in alluvial deposits at the Earth’s surface. Full article

The Atacama Desert, the driest and oldest desert on Earth, hosts a unique floral phenomenon known as the Desierto Florido (Flowering Desert), which occurs sporadically in response to rare rainfall events. Bomarea ovallei (Phil.) Ravenna is an endemic and endangered species of the Atacama Desert. However, its populations are geographically restricted and potentially vulnerable to genetic erosion due to isolation and extreme environmental conditions. This study aims to assess the genetic diversity of B. ovallei populations and develop microsatellite markers using next-generation sequencing (NGS) technology. A total of 268 microsatellite loci were identified, and 34 co-dominant markers were successfully developed for the first time in B. ovallei. Genetic diversity analysis using eight fluorescently labeled SSR markers revealed low genetic diversity across four populations, with the highest diversity observed in the QCA population, located within Llanos de Challe National Park, and the lowest in the TOTO population, which is highly exposed to anthropogenic activities. UPGMA and STRUCTURE analyses revealed three genetic clusters and high admixture among populations, suggesting historical or ongoing gene flow despite geographical separation. The presence of non-polymorphic loci and low PIC values in some markers further supports limited genetic variation. The newly developed microsatellite markers offer a valuable tool for future genetic studies, enabling the monitoring of genetic diversity and informing strategies for the preservation of this rare and ecologically significant species. Full article

By performing first-principles calculations, we predicted a kind of novel ultrathin two-dimensional (2D) ferromagnet, single-atomic-layer EuN. EuN monolayer is a ferromagnetic half-metal with a large band gap of 1.69 eV; Eu ions in EuN are in the highest spin state and have large magnetic moments of 6 μB, much larger compared with the non-rare-earth (RE) metal ions. The magneto-crystalline anisotropy energy (MCE) of EuN monolayer is −3.72 meV per Eu ion, which is much higher than that of CrI₃ monolayer (0.685 meV per Cr ion); the magnetic dipolar energy (MDE) enhances magnetic anisotropy for EuN monolayer; large magnetic anisotropy energy (MAE) is beneficial to stabilizing the long-range ferromagnetic ordering. More importantly, different from many RE metal monolayers, hybridization between Eu-f and N-p orbitals induces ferromagnetism for EuN monolayer; the Curie temperature of EuN monolayer is above the liquid-nitrogen temperature (100 K). Additionally, the Curie temperature of EuN monolayer increases with increasing biaxial strain due to increased f-p hybridization. Full article