Search Results (504)

Copper oxide (CuO) is a narrow-bandgap p-type semiconductor promising for visible-light photocatalysis, yet it suffers from rapid charge recombination and low carrier transfer efficiency. In this study, two distinct CuO photocatalysts were fabricated via different routes: two-dimensional CuO nanosheets derived from annealing a CuBDC metal–organic framework (MOF) precursor, and oriented one-dimensional CuO nanoflower arrays prepared by electrochemical deposition, followed by annealing. The crystal structure, morphology, optical absorption, and photoelectrochemical properties were systematically characterized by XRD, SEM, XPS, UV-Vis spectroscopy, transient photocurrent response, EIS, and PL spectroscopy. The CuO nanoflower thin film exhibits a broad visible-light absorption, a markedly higher photocurrent density (42.25 μA cm⁻²), and lower charge-transfer resistance compared to CuO nanosheets. When evaluated for visible-light photocatalytic degradation of methylene blue (MB), rhodamine B (RhB), and malachite green (MG), the CuO thin film completely degraded MB within 15 min, with an apparent rate constant of 20.15 h⁻¹—approximately three times that of CuO nanosheets. It also showed 1.2- and 1.28-fold higher activity for RhB and MG, respectively. The enhanced performance is attributed to the oriented nanoflower architecture that provides continuous charge transport pathways, suppresses carrier recombination, and extends light propagation via multiple reflections. This work demonstrates that microstructural engineering is an effective strategy to overcome the intrinsic limitations of CuO photocatalysts for wastewater treatment. Full article

High-performance thermal protection materials are urgently required in harsh thermal environments, such as hypersonic vehicles, the thermal runaway of energy batteries and high-temperature equipment. Conventional aerogels only exhibit passive thermal insulation and fail to resist instantaneous high-temperature attack. Herein, a cooling material of ammonium oxalate (AO) was introduced to achieve efficient, active endothermic protection. A cellular isolation effect induced by graphene nanosheets combined with anti-solvent crystallization was adopted to significantly decrease the size of AO crystals by over 93%. Based on superfine morphology and the constructed conduction network, the decomposition rate and heat absorption capacity of obtained graphene-doped AO powders (GdAPs) are improved by 41.2% and 30.4%, respectively. The mechanisms of morphology regulation and enhanced heat absorption are explored specifically in this study. Furthermore, GdAPs are embedded in phenolic resin to prepare thermal protection composite materials. Benefiting from their nearly complete thermal decomposition, GdAPs serve as a sacrificial template to generate discrete micropores in pyrolyzed resin. So, the as-prepared carbon aerogels (CAs) with a regulable microstructure exhibit an extremely low thermal conductivity of 0.056 W/(m·K), which is lower than those of reported CAs with the same density. Based on the above advantages, a synergistic endothermic-insulating thermal protection material is reported for the first time, and its heating rate is only 28.6% of that of commercial silica aerogel under identical high-temperature shock. Therefore, a new accessible strategy is demonstrated to provide high-efficiency thermal protection for resisting both abrupt and prolonged high temperature. Full article

To address the uneven deposition of zirconium conversion coatings on multiphase 55AlZnMg under short pretreatment cycles, this study investigated the time-dependent formation behavior of ZrCC in a selected H₂ZrF₆ bath. By precisely controlling the immersion time (20–90 s) and utilizing SEM-EDS and AFM characterization techniques, this study systematically revealed the growth kinetics and film-forming mechanisms of ZrCC on complex alloy surfaces. The results indicate that the Zn-rich phase on the surface of the 55AlZnMg coating, due to its relatively positive potential, preferentially induces the deposition of the film-forming material. Subsequently, dealloying occurs in the Al-rich phase and the Mg/Zn enriched regions, forming Zn-enriched regions that promote the continuous deposition of the film-forming material, ultimately achieving complete surface coverage; the film morphology evolves from an initial needle-like structure to a network structure, eventually forming a nanosheet structure. The film-forming process of ZrCC on the 55AlZnMg substrate surface is primarily driven by selective growth, with electrochemical properties of the alloy phases, significantly enhancing adhesion between the aluminum-zinc-magnesium coating and the overcoat and providing practical guidance for improving surface uniformity and interfacial adhesion of Al-Zn-Mg-coated steel. Full article

Water contaminated by textile dyes is a tremendous risk to human health and the environment due to its toxic and carcinogenic nature, thus requiring advanced and efficient removal strategies. Therefore, this study aimed to investigate the photo-oxidation performance of few- and multi-layer Ti₃C₂T_x nanosheets (MXenes) decorated with TiO₂ nanoparticles for methyl orange removal from synthetic solutions. The quantification of photogenerated hydroxyl radicals by fluorescence revealed much higher OH^• production for TiO₂-decorated samples, especially for multi-layer MXene, in which it was 2.8 times higher than that of few-layer MXene. However, photocatalysis was morphology-controlled: despite lower OH^•, the few-layer MXene achieved the highest dye conversion (~45% after 5 h), attributed to shorter charge migration distances and more accessible TiO₂ active sites, enabling effective h⁺ and superoxide-driven pathways. Moreover, the detected -OH surface terminations verified on MXenes promoted a notable adsorption capacity, especially for the multi-layer samples (~31%) via interlayer trapping and H-bonding. Therefore, our results demonstrate that few-layer MXenes are promising candidates for the efficient removal of methyl orange and highlight the potential of TiO₂-decorated MXenes as promising photocatalysts for environmental remediation. Full article

Transition-metal oxide/layered double hydroxide (LDH) electrodes often suffer from insufficient utilization of active sites, sluggish electron/ion transport, and limited cycling stability at high rates. Here, La-doped ZnCo₂O₄/MnCo-LDH nanoflowers serve as the positive electrode and Ti-supported Sb-doped SnO₂ (Ti/Sb-SnO₂) serves as the negative electrode for constructing an asymmetric supercapacitor. A stepwise hydrothermal route, La-doping regulation, and ethylenediamine-assisted morphology control transform stacked nanosheets into open porous nanoflowers with a specific surface area of 382.5 m² g⁻¹, thereby exposing more electroactive sites and shortening OH⁻ diffusion pathways. La³⁺-induced lattice distortion and defect-related oxygen species further tune the electronic structure and improve interfacial charge-transfer kinetics. The optimized La-ZnCo₂O₄/MnCo-LDH electrode delivers 2130 F g⁻¹ at 1 A g⁻¹ and retains 1993 F g⁻¹ after 10,000 cycles at 3 A g⁻¹. The Ti/Sb-SnO₂ negative electrode provides 673 F g⁻¹ at 1 A g⁻¹ and 302 F g⁻¹ at 15 A g⁻¹. The assembled device operates stably from 0 to 1.8 V in 2 M KOH and achieves 69 Wh kg⁻¹ and 13,500 W kg⁻¹. Full article

Municipal solid waste incineration fly ash (MSWI FA) represents a significant environmental challenge due to its high content of toxic heavy metal (HM) and large-scale generation. This study demonstrates the feasibility pathway for converting hazardous MSWI FA into well-crystallized layered double hydroxide nanosheets (LDH-FA). Sodium dimethyl dithiocarbamate (SDD) was incorporated as a chelating stabilizer to enable synergistic HM immobilization during acid leaching and crystallization. High-resolution transmission electron microscopy (HRTEM) confirmed the characteristic two-dimensional nanosheet morphology with interlayer spacings consistent with LDH structures, while elemental mapping revealed homogeneous distribution of Pb and Zn within the nanosheet matrix. SDD dosages higher than 1.0 wt% effectively suppressed HM leaching, and Pb concentrations were controlled below 0.1 mg/L and Zn maintained at minimal levels. BCR sequential extraction analysis further demonstrated that SDD treatment effectively transformed HMs from bioavailable acid-soluble fractions to stable forms. This investigation establishes an innovative approach to MSWI FA resource utilization and provides mechanistic insights into HM stabilization within LDH nanostructures, offering a scientific basis for safer applications of waste-derived nanomaterials. Full article

Tin disulfide (SnS₂) has attracted extensive research attention due to its superior properties originating from its unique crystalline structure. However, its practical applications are greatly restricted by difficult morphology regulation and insufficient photoresponse capability. Herein, we successfully synthesized copper and carbon co-doped SnS₂ (Cu-C-SnS₂) nanosheets via a carbon dot-assisted hydrothermal method. The morphology, crystal structure and chemical composition of the obtained samples were characterized by FE-SEM, XRD and XPS. The experimental results reveal that the synthesized Cu-C-SnS₂ presents nanosheet morphology with a bandgap of approximately 2.445 eV. Moreover, carbon dots and copper doping can effectively regulate the morphology of SnS₂, which provides a reliable strategy for the controllable synthesis of SnS₂ nanosheets. Meanwhile, the photoelectric device based on the as-fabricated Cu-C-SnS₂ nanosheets were successfully fabricated, and exhibited favorable photoelectric response under 405 nm light irradiation. Full article

The present research article deals with the thermal degradation study of epoxy resins filled with hybrid nanostructured forms of carbon under oxidative conditions. In particular, the formulated polymer composites (denoted as HYB_0.1%_CNTs:GNs and HYB_0.5%_CNTs:GNs, respectively) consist of two kinds of fillers, namely multi-walled carbon nanotubes (CNTs) and graphene nanosheets (GNs), mixed together with two different total mass amounts: 0.1 and 0.5%. In both kinds of nanocomposites, three different CNT:GN mixing ratios were considered (5:1, 1:1, and 1:5, respectively), thus providing a total of six hybrid samples. The thermal behavior of these samples was studied by simultaneous thermogravimetry and differential thermal analysis (TG/DTA) under flowing air, and two processes took place in distinct temperature ranges. In each step, about 50% of mass loss is detected with an exothermic effect in the corresponding DTA curve, with the second one accompanied by an intense heat release. The kinetic analysis of the two-stage oxidative thermal degradation was investigated using a model-free isoconversional approach. A non-Arrhenian behavior of the temperature function k(T) was assumed, and lifetime prediction was estimated at temperatures close to those of the possible applications. Isoconversional analysis shows nearly constant activation energies for all composites except HYB_0.1%_5:1 (from 142 to 96 kJ·mol⁻¹), while lifetime predictions indicate that thermal stability increases with graphene content at 0.1% loading (HYB_0.1%_1:5) and with CNT content at 0.5% loading (HYB_0.5%_5:1), with uncertainties below 7%. Finally, because of the π–π bond interactions between the CNTs and the GNs dispersed in the epoxy resin matrix, an effective and remarkable electrical performance was found and a correlation with both electrical and morphological properties was established. In this regard, Tunneling Atomic Force Microscopy (TUNA) proved to be particularly powerful in allowing the simultaneous mapping of topography and localized conductive networks with exceptional sensitivity to nanofiller dispersion, such as CNTs and GNs. DC conductivity increased by up to nine orders of magnitude at 0.1 wt% hybrid loading (up to 3.73 × 10⁻⁴ S/m vs. 1.06 × 10⁻¹³ S/m for CNT-only), with nanoscale TUNA currents (−1.9 to 4.5 pA) mirroring macroscopic trends, while at 0.5 wt% all hybrids reached 10⁻² S/m, indicating reduced synergy once a fully developed conductive network is established. Full article

The persistent accumulation of antibiotic pollutants in aquatic environments poses potential threats to ecological safety and human health, highlighting the importance of developing low-cost, high-performance adsorbents for their efficient removal. In this study, a hydrothermal method was employed to prepare highly dispersed coal gangue-based calcium silicate hydrate (CSH) adsorbents. The structural characteristics, adsorption performance, and adsorption mechanisms of the material were systematically investigated. The as-prepared CSH exhibited an interwoven nanorod/nanosheet composite morphology with a more developed pore structure and a higher specific surface area. Kinetic analysis indicated that the adsorption process followed a pseudo-second-order model and involved both Boyd diffusion and intraparticle diffusion, with liquid-film diffusion likely serving as the primary rate-limiting step. Isotherm analysis revealed that the adsorption behavior was well described by the Langmuir model, suggesting monolayer adsorption, with a theoretical adsorption capacity (Q_m) of 129.29 mg/g. Thermodynamic analysis further demonstrated that the adsorption of CIP onto CSH was a spontaneous and endothermic process. Combined characterization results and theoretical calculations suggested that the adsorption of CIP by CSH was mainly governed by surface oxygen containing active sites, accompanied by electrostatic interactions, hydrogen bonding, and possible surface coordination effects. In addition, CSH maintained excellent adsorption performance and structural stability in the presence of coexisting ions, in tap water systems, and after repeated adsorption–desorption cycles. This study not only enables the high-value utilization of coal gangue but also provides new insights into the development of low-cost adsorbent materials for antibiotic removal. Full article

The development of high-performance electrode materials with controlled morphology remains a key challenge for advancing supercapacitor technologies. In this study, polyethylene glycol (PEG)-assisted hydrothermal synthesis was employed to engineer NiCo₂S₄ nanostructures with controlled morphology for enhanced supercapacitor performance. The influence of PEG concentration on nucleation behavior, structural evolution, and electrochemical characteristics was systematically investigated. The optimized NiCo₂S₄ electrode synthesized with 0.2% PEG (NiCoS-P2) exhibited a hierarchical flower-like nanosheet architecture with reduced agglomeration and improved electrochemically accessible surface area. As a result, the electrode delivered a high areal capacitance of 13.689 F/cm² (specific capacitance of 6845 F/g) at 5 mA/cm², along with excellent rate capability and superior cycling stability, retaining 84.16% capacitance after 12,000 cycles. Electrochemical analysis revealed that the charge storage process is predominantly diffusion-controlled with enhanced ion transport kinetics. Furthermore, an asymmetric supercapacitor device assembled using NiCoS-P2 as the positive electrode and activated carbon as the negative electrode demonstrated a wide operating voltage of 1.5 V, delivering an areal capacitance of 0.409 F/cm² (specific capacitance of 204.5 F/g), an energy density of 0.128 mWh/cm², and a power density of 2.99 mW/cm². The device also exhibited excellent long-term stability with 85.3% capacitance retention after 7000 cycles. This work highlights the effectiveness of polymer-assisted structural engineering in optimizing transition metal sulfide electrodes for advanced energy storage applications.: Full article

In this study, Zn-doped Co₃O₄ nanorods and nanosheets with controlled Zn/Co molar ratios were synthesized via a hydrothermal strategy to clarify the respective roles of morphology and elemental doping in ethylbenzene sensing. The gas-sensing performance is strongly influenced by morphology, and the radially oriented nanorod structure significantly enhances sensing response compared with nanosheet structures. Zn doping effectively enhances the gas-sensing performance of Co₃O₄. As a result, the optimized Zn-doped nanorod sensor exhibits high sensitivity to ethylbenzene, a low detection limit, rapid response and recovery, and excellent operational stability. Density functional theory calculations reveal that the predominantly exposed facets of the nanorod structure possess stronger adsorption affinity and pronounced charge transfer toward ethylbenzene, providing theoretical support for the morphology-dominated sensing behavior. At the same time, Zn incorporation further adjusts the band structure and surface reactivity. Overall, this work elucidates a morphology-dominated and doping-assisted enhancement mechanism, offering clear design principles for high-performance Co₃O₄-based ethylbenzene sensors. Full article

To address the application requirements of energy storage devices for new energy electric vehicles—including high energy density, high-power density, fast charging and discharging, and long-term cycling stability—traditional symmetric supercapacitors are often limited by low energy density and poor compatibility between the anode and cathode, making it difficult to meet the high-efficiency energy storage demands under the dynamic operating conditions of electric vehicles. This study focuses on the regulation of hierarchical thin-film structures and the innovative heterogeneous coating interface engineering with precise slurry coating and film-forming optimization and designs and fabricates NiCo₂O₄/NiFeO composite thin-film electrodes and Mn-doped porous carbon (Mn-PC) thin-film electrodes. The uniform, compact and stable coating formation on nickel foam substrates via controllable slurry coating facilitates the efficient integration of active materials and conductive supports. The electrode slurries were coated onto conductive nickel foam substrates, and high-performance aqueous supercapacitors were assembled using an asymmetric configuration. A systematic study was conducted covering material preparation, structural characterization, electrochemical testing, and full-device performance evaluation. Using techniques such as XRD, XPS, SEM, TEM, BET, and an electrochemical workstation, the study revealed the structure–activity relationships among material morphology, crystalline phases, pore structure, and electrochemical performance, elucidating the charge storage mechanisms of the composite electrode films and the principles of synergistic adaptation between the anode and cathode. The results indicate that NiCo₂O₄ nanowires decorated with in situ-grown NiFeO nanosheets to form a composite structure; when coated onto nickel foam, this forms a uniform, porous electrode film with a specific surface area of 171.3 m²/g, a specific capacitance as high as 1746 F/g at 1 A/g, and a capacity retention rate of 94.0% after 10,000 cycles. After coating and film formation, the Mn-PC anode introduced pseudocapacitive active sites through uniform Mn doping, resulting in a film electrode specific capacitance of 348 F/g and significantly improved rate and cycling performance. The assembled NiCo₂O₄/NiFeO//Mn-PC asymmetric supercapacitor exhibits a thin-film electrode specific capacitance of 153 F/g at 1 A/g, with a maximum energy density of 52 Wh/kg. Even at a power density of 9000 W/kg, it maintains 45 Wh/kg, and retains 89.5% of its capacity after 10,000 cycles, with overall performance outperforming most previously reported transition metal-based devices. This coating-engineered electrode fabrication strategy breaks through the interface mismatch and structural instability bottlenecks of traditional thin-film electrodes, providing a novel material system and an efficient coating assembly strategy for high-performance supercapacitor thin-film electrodes in new energy electric vehicles, and offers experimental evidence and technical references for the development and application of high-power energy storage coating devices for automotive use, as well as the innovative design of electrode coating engineering in energy storage fields. Full article

Zinc oxide (ZnO) nanomaterials have attracted widespread attention from researchers due to their morphology-dependent properties, eco-friendly characteristics, and potential as a sustainable photocatalyst with a broad range of applications. Therefore, in this study, three different ZnO nanostructures—nanosheets (NSs), nanoflowers (NFs), and nanorods (NBs)—were synthesized via a controlled precipitation method. Among these, NFs exhibited the highest photocatalytic efficiency. The obtained samples exhibited broad optical absorption edges extending into the visible region (corresponding to apparent energies of 1.81–2.09 eV), which is attributed to the sub-bandgap states induced by oxygen vacancies rather than intrinsic bandgap narrowing—far lower than the bandgap of bulk ZnO (3.37 eV). Their photocatalytic performance was evaluated by the degradation of Methyl Blue (MB), Methyl Orange (MO), and Rhodamine B (RhB) under UV or sunlight. Notably, the NFs achieved rapid degradation of MB and RhB within 90 min under UV irradiation without the addition of any H₂O₂, demonstrating their effectiveness and cost-effectiveness for practical applications. Although H₂O₂ inhibited the degradation of MB and RhB, it promoted the decomposition of MO. Furthermore, the ZnO NFs exhibited excellent recyclability in five consecutive degradation cycles. The self-synthesized ZnO nanomaterials in this study, with their broad-spectrum absorption, high stability, and eco-friendly properties, demonstrate their potential as an efficient and low-cost photocatalyst for large-scale wastewater treatment. Full article

The transformation of waste plastics into hydrogen and functional carbon (C) materials represents a promising pathway for achieving both resource recycling and the production of value-added products. Owing to their tunable physicochemical properties, plastic-derived carbons have attracted significant attention in electrochemical energy storage applications. Various C nanostructures, including graphene, porous C, hard C, and C nanotubes (CNTs), can be generated from discarded plastics through thermochemical processes. The electrochemical performance of these materials is closely governed by their structural characteristics, such as pore architecture, specific surface area, heteroatom doping, surface functionalities, and dimensional morphology. This review aims to provide a comprehensive and systematic overview of the conversion of waste plastics into functional C nanomaterials via thermochemical routes, particularly catalytic pyrolysis and carbonization. The resulting C nanostructures are systematically categorized based on their dimensional architectures (0D, 1D, 2D, and 3D) and comparatively analyzed in terms of their structural features and electrochemical performance. Emphasis is placed on the transformation of diverse plastic feedstocks into high-value C materials with tailored dimensional architectures, including graphene, CNTs, C nanospheres, C nanosheets, porous carbons, and their composites. Furthermore, recent progress and critical challenges in utilizing these materials for electrochemical energy storage systems, such as supercapacitors and rechargeable batteries (Li-ion, Na-ion, K-ion, Li-S, and Zn-air), are discussed. Distinct from previous reports, this review highlights the correlation between thermochemical processing strategies, resulting structural features, and electrochemical performance, providing new insights into the rational design of high-performance C materials. These findings are expected to facilitate the advancement of sustainable energy storage technologies while contributing to effective plastic waste valorization. Full article

The efficiency of hydrogen production via water electrolysis is severely constrained by the sluggish reaction kinetics of the oxygen evolution reaction (OER). Herein, we constructed a nitrogen-doped CoFe Prussian blue analog (CoFePBA-N) electrocatalyst with a nanosheet-assembled cubic architecture by plasma. Plasma treatment induces morphological reconstruction and introduces nitrogen dopants and abundant vacancies, which not only increase the number of exposed active sites but also modulate the electronic structure of Co/Fe centers. Consequently, the optimized CoFePBA-N catalyst achieves a current density of 500 mA cm⁻² at low overpotentials of 322, 344, and 374 mV in alkaline freshwater, alkaline simulated seawater, and alkaline natural seawater, respectively. Furthermore, the catalyst maintains stable operation for over 300 h in alkaline freshwater and nearly 270 h in alkaline natural seawater, exhibiting exceptional durability. The enhanced catalytic performance is attributed to the synergistic effects of nitrogen doping, vacancies, and improved charge-transfer capability. This study provides an effective approach for modulating the electronic structure of Prussian blue analogs, thereby enabling efficient alkaline water and seawater electrolysis. Full article