Search Results (19)

Mixed-halide perovskites enable the creation of high-performance and low-cost solar cells. Chloride incorporation enhances film morphology, carrier diffusion length, and stability, improving device performance. Nevertheless, optimizing film thickness, defect density, and metal contact work function remains insufficiently explored, despite its potential to enhance power conversion efficiency. In this study, a numerical simulation was performed using SCAPS-1D (version 3.3.10) to identify the optimal parameters for the FTO/TiO₂/CH₃NH₃Pb_3−xCl_x/Spiro-OMeTAD/Au configuration. The best performance parameters that have been published in the literature based on experimental results are as follows: V_OC = 1.077 V, J_SC = 21.45 mA/cm², FF = 77.57%, and PCE = 17.97%. In contrast, the performance parameters obtained from numerical simulations for the same structure are V_OC = 1.28 V, J_SC = 21.63 mA/cm², FF = 78%, and PCE = 21.53%. In our numerical analysis, we achieved efficiencies that were comparable to those reported in experimental studies, and after optimization, superior performance parameters were attained, including V_OC = 1.179 V, J_SC = 27.26 mA/cm², FF = 81.03%, and PCE = 26.07%. These results indicate that optimized parameters can be integrated into the design and fabrication of mixed-halide perovskite solar cells to enhance performance. Full article

The use of organic halide salts to passivate metal halide perovskite (MHP) surface defects has been studied extensively. Passivating the surface defects of the MHP is of critical importance for realizing highly efficient and stable perovskite solar cells (PSCs). Here, the successful application of a multifunctional organic salt, methyltriphenylphosphonium iodide (MTPPI), used as a passivation additive for grain boundary defects and as a molecular sealing layer in terms of stabilization, has been used to stabilize the mixed cation perovskite RbCsMAFA-PbIBr. To assess the passivating and stabilizing effects of MTPPI on RbCsMAFA-PbIBr PSCs, maximum power point tracking (MPPT) was applied as the most realistic and closest-to-application condition for the ageing test. Here, perovskite solar cells were aged under a light source yielding an excitation intensity corresponding to one sun with maximum power point tracking, which was interrupted periodically by current–voltage sweeps. This allowed for the extraction of all photovoltaic parameters necessary for a proper understanding of the ageing process. The MTPPI additive can donate iodine anions to halide vacancies and compensate a negative surface excess charge with cation interactions. On top of this, the large and bulky methyltriphenylphosphonium (MTPP⁺) cation may block both the escape of volatile perovskite components and the ingress of oxygen and water vapour. These collective roles of MTPPI have improved both the efficiency and stability of the solar cells compared to the reference without passivation additives. Full article

This review provides an analysis of non-perovskite hybrid halides of coinage metals templated by metal–organic cations (CCDC November 2023). These materials display remarkable structural diversity, from zero-dimensional molecular complexes to intricate three-dimensional frameworks, allowing fine-tuning of their properties. A total of 208 crystal structures, comprising haloargentates, mixed-metal haloargentates, and halocuprates, are categorized and examined. Their potential in photocatalysis is discussed. Special attention is given to the structural adaptability of these materials for the generation of functional interfaces. This review highlights key compounds and aims to inspire further research into optimizing hybrid halides for advanced technological applications. Full article

Tin oxide (SnO₂) has been recognized as one of the beneficial components in the electron transport layer (ETL) of lead–halide perovskite solar cells (PSCs) due to its high electron mobility. The SnO₂-based thin film serves for electron extraction and transport in the device, induced by light absorption at the perovskite layer. The focus of this paper is on the heat treatment of a nanoaggregate layer of single-nanometer-scale SnO₂ particles in combination with another metal-dopant precursor to develop a new process for ETL in PSCs. The combined precursor solution of Li chloride and titanium(IV) isopropoxide (TTIP) was deposited onto the SnO₂ layer. We varied the heat treatment conditions of the spin-coated films comprising double layers, i.e., an Li/TTIP precursor layer and SnO₂ nanoparticle layer, to understand the effects of nanoparticle interconnection via sintering and the mixing ratio of the Li-dopant on the photovoltaic performance. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM) measurements of the sintered nanoparticles suggested that an Li-doped solid solution of SnO₂ with a small amount of TiO₂ nanoparticles formed via heating. Interestingly, the bandgap of the Li-doped ETL samples was estimated to be 3.45 eV, indicating a narrower bandgap as compared to that of pure SnO₂. This observation also supported the formation of an SnO₂/TiO₂ solid solution in the ETL. The utilization of such a nanoparticulate SnO₂ film in combination with an Li/TTIP precursor could offer a new approach as an alternative to conventional SnO₂ electron transport layers for optimizing the performance of lead–halide perovskite solar cells. Full article

Perovskite-based metal oxide phototransistors have emerged as promising photodetection devices owing to the superior optoelectronic properties of perovskite materials and the high carrier mobility of metal oxides. However, high dark current has been one major problem for this type of device. Here, we studied the dark current behaviors of phototransistors fabricated based on the Indium Gallium Zinc Oxide (IGZO) channel and different perovskite materials. We found that depositing organic–inorganic hybrid perovskites materials (MAPbI₃/FAPbI₃/FA_0.2MA_0.8PbI₃) on top of IGZO transistor can increase dark current from ~10⁻⁶ mA to 1~10 mA. By contrast, we observed depositing an inorganic perovskite material, CsPbI₃, incorporated with PCBM additive can suppress the dark current down to ~10⁻⁶ mA. Our study of ion migration reveals that ion migration is pronounced in organic–inorganic perovskite films but is suppressed in CsPbI₃, particularly in CsPbI₃ mixed with PCBM additive. This study shows that ion migration suppression by the exclusion of organic halide and the incorporation of PCBM additive can benefit low dark current in perovskite phototransistors. Full article

Mixed-halide perovskite quantum dots (PeQDs) are the most competitive candidates in designing solar cells and light-emitting devices (LEDs) due to their tunable bandgap and high-efficiency quantum yield. However, phase separation in mixed-halide perovskites under illumination can form rich iodine and bromine regions, which change its optical responses. Herein, we synthesize PeQDs combined with mesoporous zinc-based metal organic framework (MOF) crystals, which can greatly improve the stability of anti-anion exchange, including photo-, thermal, and long-term stabilities under illumination. This unique structure provides a solution for improving the performance of perovskite optoelectronic devices and stabilizing mixed-halide perovskite devices. Full article

Perovskite solar cells have become the current research focus because of their high conversion efficiency and other advantages; however, the toxicity of lead used in them has raised environmental concerns. Tin-based perovskite materials have become the most promising alternative materials for perovskite solar cells because of their relatively low toxicity, suitable band gap and relatively higher energy conversion efficiency than perovskite materials based on other elements. In this article, the status of this rapidly growing field, authors’ output and cooperation, hot research topics, important references and the development trends of tin-based perovskite solar cells are identified and visualized using CiteSpace software. The main research fields are found to be optical properties, 3D–2D perovskite and perovskite solar cell conduction band materials. The mixed organic metal halide perovskite solar cell and the CsSnI₃ semiconductor are identified as emerging trends for tin-based perovskite solar cells. Such contents in this article highlight the key points in the wide field of literature so it can be understood efficiently. Full article

Heavy metal pollution in river and lake sediments seriously damages river ecological safety and indirectly affects human health. The existing research mainly focuses on how to adsorb pollutants and repair sediment, and how the reuse of these pollutants may be a new technology to control sediment pollutants. The rapid development of perovskite solar cells in recent years has attracted a lot of attention, among which lead (Pb) halide perovskites have very excellent photoelectric performance. In this study, we propose a novel idea of introducing indium (In)-based perovskite to replace Pb (II) ions dispersed in river and lake sediment. Three sediment samples from a river in Shanghai Peace Park were collected to analyze the distribution of heavy metal Pb. We mixed the digestion solution of sediment with the prepared CH₃NH₃(MA)InICl₂ solution and found that indium (In) in perovskite precursor solution would be gradually replaced by Pb in sediments. An in situ synchrotron radiation XRD experiment was performed to reveal the reaction mechanism of solutions and provide a good research platform for the comprehensive reuse of sediment in the future. This study provides a new method of remediation of heavy metal pollution in river and lake sediments. Full article

Metal halide perovskites (MHPs) are emerging next-generation light emitters that have attracted attention in academia and industry owing to their low material cost, simple synthesis, and wide color gamut. Efficient strategies for MHP modification are being actively studied to attain high performance demonstrated by commercial light-emitting diodes (LEDs) based on organic emitters. Active studies have overcome the limitations of the external quantum efficiencies (EQEs) of green and red MHP LEDs (PeLEDs); therefore, the EQEs of PeLEDs (red: 21.3% at 649 nm; green: 23.4% at 530 nm) have nearly reached the theoretical limit for the light outcoupling of single-structured planar LEDs. However, the EQEs of blue PeLEDs (12.1% at 488 nm and 1.12% at 445 nm) are still lower than approximately half of those of green and red PeLEDs. To commercialize PeLEDs for future full-color displays, the EQEs of blue MHP emitters should be improved by approximately 2 times for sky-blue and more than 20 times for deep-blue MHP emitters to attain values comparable to the EQEs of red and green PeLEDs. Therefore, based on the reported effective approaches for the preparation of blue PeLEDs, a synergistic strategy for boosting the EQE of blue PeLEDs can be devised for commercialization in future full-color displays. This review covers efficient strategies for improving blue PeLEDs using fundamental approaches of material engineering, including compositional or dimensional engineering, thereby providing inspiration for researchers. Full article

Halide perovskite colloidal nanocrystals have recently gained much attention thanks to their superior stability compared with their bulk counterpart and to their unique optical properties. In this paper, two systems combining nanocrystals and nanoporous gold are studied to create an optimal metal semiconductor heterojunction that can be used in photocatalysis and photovoltaic devices. The perovskite degradation phenomenon is observed when the nanoporous gold powder is mixed into the hexane suspension of nanocrystals, while the charge separation efficiency is increased by synthesizing the nanocrystals directly onto the gold porous structure. The analysis of the structural and optical properties evidences an energy transfer efficiency of 47%, along with the high structural stability of the hybrid system. Full article

Development of graphene/perovskite heterostructures mediated by polymeric materials may constitute a robust strategy to resolve the environmental instability of metal halide perovskites and provide barrierless charge transport. Herein, a straightforward approach for the growth of perovskite nano-crystals and their electronic communication with graphene is presented. Methylammonium lead bromide (CH₃NH₃PbBr₃) nano-crystals were grown in a poly[styrene-co-(2-(dimethylamino)ethyl methacrylate)], P[St-co-DMAEMA], bi-functional random co-polymer matrix and non-covalently immobilized on graphene. P[St-co-DMAEMA] was selected as a bi-modal polymer capable to stabilize the perovskite nano-crystals via electrostatic interactions between the tri-alkylamine amine sites of the co-polymer and the A-site vacancies of the perovskite and simultaneously enable Van der Waals attractive interactions between the aromatic arene sites of the co-polymer and the surface of graphene. The newly synthesized CH₃NH₃PbBr₃/co-polymer and graphene/CH₃NH₃PbBr₃/co-polymer ensembles were formed by physical mixing of the components in organic media at room temperature. Complementary characterization by dynamic light scattering, microscopy, and energy-dispersive X-ray spectroscopy revealed the formation of uniform spherical perovskite nano-crystals immobilized on the graphene nano-sheets. Complementary photophysical characterization by UV-Vis absorption, steady-state, and time-resolved fluorescence spectroscopy unveiled the photophysical properties of the CH₃NH₃PbBr₃/co-polymer colloid perovskite solution and verified the electronic communication within the graphene/CH₃NH₃PbBr₃/co-polymer ensembles at the ground and excited states. Full article

In this work, metal halide perovskite quantum dots (QDs) with Formamidinium (FA) and Cs mixed cations were fabricated using a solution-processed method at room temperature. By controlling Cs doping ratios in a precursor, the optical properties of mixed-cation perovskite QDs were systematically studied. With the increase in Cs ion doping, the photoluminescence (PL) spectra of perovskite QDs were blueshifted, which was mainly due to the smaller radius of Cs ions than those of FA. Temperature-dependent PL spectra were conducted on mixed-cation perovskite QDs. As the temperature gradually increased from 4 K to 300 K, PL peaks were blue shifted, and full-width at half maximum (FWHM) was widened, which was directly related to lattice thermal expansion and the carrier-photon coupling effect under temperature variation. At the same time, excess Cs ion doping had a prominent influence on optical properties at low temperatures, which was mainly due to the introduction of detrimental defects in perovskite crystals. Therefore, it is particularly important to control doping concentration in the preparation of high-quality perovskite QDs and efficient photoelectric devices. Full article

All-inorganic metal halide perovskite nanocrystals (IPeNCs) have become one of the most promising luminescent materials for next-generation display and lighting technology owing to their excellent color expression ability. However, research on IPeNCs with stable blue emission is limited. In this paper, we report stable blue emissive all-bromide IPeNCs obtained through a modified ligand-assisted reprecipitation method using an ultraviolet (UV)-curable prepolymer as the anti-solvent at a low temperature. We found that the blue emission originates from quantum-confined CsPbBr₃ nanoparticles formed together with the colorless wide-bandgap Cs₄PbBr₆ nanocrystals. When the temperature of the prepolymer was increased from 0 to 50 °C, CsPbBr₃ nanoparticles became larger and more crystalline, thereby altering their emission color from blue to green. The synthesized all-bromide blue-emitting IPeNC solution remained stable for over 1 h. It also remained stable when it was mixed with the green-emitting IPeNC solution. By simply exposing the as-synthesized IPeNC–prepolymer solutions to UV light, we formed water-stable composite films that emitted red, green, blue, and white colors. We believe that this synthetic method can be used to develop color-emitting composite materials that are highly suitable for application as the color conversion films of full-color liquid crystal display backlight systems and lighting applications. Full article

Perovskite solar cells that use carbon (C) as a replacement of the typical metal electrodes, which are most commonly employed, have received growing interest over the past years, owing to their low cost, ease of fabrication and high stability under ambient conditions. Even though Power Conversion Efficiencies (PCEs) have increased over the years, there is still room for improvement, in order to compete with metal-based devices, which exceed 25% efficiency. With the scope of increasing the PCE of Carbon based Perovskite Solar Cells (C-PSCs), in this work we have employed a series of ammonium iodides (ammonium iodide, ethylammonium iodide, tetrabutyl ammonium iodide, phenethylammonium iodide and 5-ammonium valeric acid iodide) as additives in the multiple cation-mixed halide perovskite precursor solution. This has led to a significant increase in the PCE of the corresponding devices, by having a positive impact on the photocurrent values obtained, which exhibited an increase exceeding 20%, from 19.8 mA/cm², for the reference perovskite, to 24 mA/cm², for the additive-based perovskite. At the same time, the ammonium iodide salts were used in a post-treatment method. By passivating the defects, which provide charge recombination centers, an improved performance of the C-PSCs has been achieved, with enhanced FF values reaching 59%, which is a promising result for C-PSCs, and V_oc values up to 850 mV. By combining the results of these parallel investigations, C-PSCs of the triple mesoscopic structure with a PCE exceeding 10% have been achieved, while the in-depth investigation of the effects of ammonium iodides in this PSC structure provide a fruitful insight towards the optimum exploitation of interface and bulk engineering, for high efficiency and stable C-PSCs, with a structure that is favorable for large area applications. Full article

Organic–inorganic hybrid perovskite materials have raised great interest in recent years due to their excellent optoelectronic properties, which promise stunning improvements in photovoltaic technologies. Moreover, two-dimensional layered materials such as graphene, its derivatives, and transition metal dichalcogenides have been extensively investigated for a wide range of electronic and optoelectronic applications and have recently shown a synergistic effect in combination with hybrid perovskite materials. Here, we report on the inclusion of liquid-phase exfoliated molybdenum disulfide nanosheets into different perovskite precursor solutions, exploring their influence on final device performance. We compared the effect of such additives upon the growth of diverse perovskites, namely CH₃NH₃PbI₃ (MAPbI₃) and triple-cation with mixed halides Cs_x (MA_0.17FA_0.83)_(1−x)Pb (I_0.83Br_0.17)₃ perovskite. We show how for the referential MAPbI₃ materials the addition of the MoS₂ additive leads to the formation of larger, highly crystalline grains, which result in a remarkable 15% relative improvement in power conversion efficiency. On the other hand, for the mixed cation–halide perovskite no improvements were observed, confirming that the nucleation process for the two materials is differently influenced by the presence of MoS₂. Full article