Search Results (134)

We use Co doping to alter the magnetic relaxation dynamics in superparamagnetic nanofluids made of 18 nm average diameter Fe₃O₄ nanoparticles immersed in Isopar M. Ac-susceptibility data recorded at different frequencies and temperatures, χ″vs. T|_f, reveals a major (~100 K) increase in the superspin blocking temperature of the Co_0.2Fe_2.8O₄-based fluid (CFO) compared to its Fe₃O₄ counterpart (FO). We ascribe this behavior to the strengthening of the interparticle magnetic dipole interactions upon Co doping, as demonstrated by the relative χ″-peak temperature variation per frequency decade $\mathsf{\Phi }={\displaystyle \frac{∆\mathrm{T}}{\mathrm{T}·∆\mathrm{l}\mathrm{o}\mathrm{g}\left(\mathrm{f}\right)}}$, which decreases from Φ~0.15 in FO to Φ~0.025 in CFO. In addition, χ″vs. T|_f datasets from the CFO fluid reveal two magnetic events at temperatures T_p1 = 240 K and T_p2 = 275 K, both above the fluid’s freezing point (T_F = 197 K). We demonstrate that the physical rotation of the nanoparticles within the fluid, the Brown mechanism, is entirely responsible for the collective superspin relaxation observed at T_p1, whereas the Néel mechanism, the superspin flip across an energy barrier within the particle, is dominant at T_p2. We confirm this finding through fits of models that describe the temperature dependence of the relaxation time via the two mechanisms: ${\mathsf{\tau }}_{\mathrm{B}}(\mathrm{T})={\displaystyle \frac{3{\mathsf{\eta }}_0{\mathrm{V}}_{\mathrm{H}}}{{\mathrm{k}}_{\mathrm{B}}\mathrm{T}}}\exp \left[{\displaystyle \frac{{\mathrm{E}}^{\prime }}{{\mathrm{k}}_{\mathrm{B}}\left(\mathrm{T}-{{\mathrm{T}}_0}^{\prime }\right)}}\right]$ and ${\mathsf{\tau }}_{\mathrm{N}}\left(\mathrm{T}\right)={\mathsf{\tau }}_0\exp \left[{\displaystyle \frac{{\mathrm{E}}_{\mathrm{B}}}{{\mathrm{k}}_{\mathrm{B}}\left(\mathrm{T}-{\mathrm{T}}_0\right)}}\right]$. The best fits yield ${\mathsf{\gamma }}_0={\displaystyle \frac{3{\mathsf{\eta }}_0{\mathrm{V}}_{\mathrm{H}}}{{\mathrm{k}}_{\mathrm{B}}}}$= 1.5 × 10⁻⁸ s·K, E′/k_B = 7 03 K, and T₀′ = 201 K for the Brown relaxation, and E_B/k_B = 2818 K and T₀ = 143 K for the Néel relaxation. Full article

We consider a multilevel atom, such as a hydrogen atom, interacting with the quantum electromagnetic field in the dressed ground state of the interacting system. Using perturbation theory within the dipole approximation, we evaluate the dressed ground state and investigate the effect of atomic self-dressing on several field and atomic observables. Specifically, we obtain general expressions of the renormalized electric and magnetic field fluctuations and energy densities around the atom, and analyze their scaling with the distance from the atom, obtaining approximated expressions in the so-called near and far zones. We also investigate nonlocal spatial field correlations around the atom. We stress how the quantities we evaluate can be probed through two- and three-body nonadditive Casimir–Polder dispersion interactions. We also investigate the effect of self-dressing—namely, the virtual transitions occurring in the dressed ground state—on atomic observables, such as the average potential energy of the electron in the nuclear field. This also allows us to obtain a more fundamental quantum basis for the Welton interpretation of the Lamb shift of a ground-state hydrogen atom, in terms of the atomic self-dressing processes. Full article

Magnetic separation is an important method in the processing process, and its essence is the targeted dispersion of the mineral processing slurry pulp in the magnetic field space. The slurry is a complex multiphase fluid system with continuous phase carrying a large number of discrete phase particles, in which the magnetic particles agglomerate, migrate, and disperse under the dominance of magnetic force. In this process, there is nonlinear and unstable dynamic coupling between the continuous phase (liquid) and the discrete phase (solid particles) and between the discrete phases. In this paper, a dynamic cyclic multi-dipole magnetic moment algorithm with a higher calculation accuracy is innovatively proposed to calculate the magnetic interaction force between particles. Moreover, the P-E magnetization model suitable for a two-dimensional uniform magnetic field is further improved and optimized to make it applicable to a three-dimensional gradient magnetic field. Finally, based on the coupling of the Finite Element Method (FEM), Computational Fluid Dynamics (CFD), and Discrete Element Method (DEM), a dynamic coupling model capable of accurately simulating the magnetic separation process is developed. This model can be used to study the separation behavior of particles under a multiphase flow and multi-force field and to explore the motion behavior of magnetic particles. Full article

Heavy metal contamination of water is a critical environmental problem due to its toxicity and persistence in ecosystems. In this study, magnetic hydrogel spheres composed of carboxymethylated starch modified with poly(1-vinylimidazole) (CMS-g-PVI) and polyvinyl alcohol (PVA), combined with Fe₃O₄ nanoparticles, were synthesized and characterized to evaluate their efficiency in adsorbing metal ions such as Cu²⁺, Pb²⁺, and Cd²⁺. Structural characterization by FT-IR spectroscopy confirmed the successful integration of all functional components into the hydrogel matrix. Additionally, scanning electron microscopy (SEM) revealed a rough and porous surface morphology favorable for adsorption and an average bead diameter of 3.2 mm, influenced by the stirring rate during synthesis. Adsorption studies demonstrated maximum capacities of 82.4 mg·g⁻¹ for Cu²⁺, 66.5 mg·g⁻¹ for Pb²⁺, and 51.8 mg·g⁻¹ for Cd²⁺, with optimal removal efficiencies at pH 6.2 and 5.7. From a theoretical perspective, density functional theory (DFT) calculations using the B3LYP/6-311+G(d,p) method allowed the optimization of molecular structures and analysis of electronic properties. The total dipole moment (TDM) of the CMS-g-PVI/PVA system reached 20.81 Debye. A significant reduction in the HOMO-LUMO energy gap was observed upon metal adsorption, with values of 0.0308 eV for Cu²⁺, 0.0175 eV for Pb²⁺, and 0.0235 eV for Cd²⁺, confirming strong interactions between the hydrogel matrix and the metal ions. The combined experimental and computational approach provides a comprehensive understanding of the adsorption mechanisms and supports the development of efficient materials for water decontamination. Full article

A chain of dipole-coupled elongated magnetic islands whose long axes are oriented perpendicular to the chain is studied for its magnetization properties. With a magnetic field applied perpendicular to the chain, the competition between dipolar energy, shape anisotropy, and field energy leads to three types of uniform states with distinct magnetizations: (1) oblique to the chain, (2) perpendicular to the chain, and (3) zero due to having alternating dipoles. The response of these states to a slowly varying field is analyzed, focusing on their stability limits and related oscillation modes, and the dependencies on the dipolar and anisotropy constants. Based on identifiable transitions among the three states and their instability points, the theoretically predicted zero-temperature magnetization curves show significant dependence on the anisotropy. The model suggests a path for designing advanced materials with desired magnetic properties. Different geometries and magnetic media for the islands are considered. Full article

We study a system of ultra-cold dipolar Bose gas atoms confined in a two-dimensional (2D) harmonic trap with a dipolar impurity implanted at the center of the trap. Due to recent experimental progress in dipolar condensates, we focused on calculating properties of dipolar impurity systems that might guide experimentalists if they choose to study impurities in dipolar gases. We used the Gross–Pitaevskii formalism solved numerically via the split-step Crank–Nicolson method. We chose parameters of the background gas to be consistent with dysprosium (Dy), one of the strongest magnetic dipoles and of current experimental interest, and used chromium (Cr), erbium (Er), terbium (Tb), and Dy for the impurity. The dipole moments were aligned by an external field along what was chosen to be the z-axis, and we studied 2D confinements that were perpendicular or parallel to the external field. We show density contour plots for the two confinements, 1D cross-sections of the densities, calculated self-energies of the impurities while varying both number of atoms in the condensate and the symmetry of the trap. We also calculated the time evolution of the density of an initially pure system where an impurity is introduced. Our results show that while the self-energy increases in magnitude with increasing number of particles, it is reduced when the trap anisotropy follows the natural anisotropy of the gas, i.e., elongated along the z-axis in the case of parallel confinement. This work builds upon work conducted in Bose gases with zero-range interactions and demonstrates some of the features that could be found when exploring dipolar impurities in 2D Bose gases. Full article

In order to properly describe the gravity interactions, including the mass currents, in gravitomagnetism, we construct four Maxwell-type gravitational equations that are shown to be analogs of the Maxwell equations in electromagnetism. Next, exploiting the Maxwell-type gravitational equations, we explicitly predict the mass magnetic fields for both the isolated system of the spinning Moon orbiting the spinning Earth and that of the Sun and solar system planets orbiting the spinning Sun, whose phenomenological values have not been evaluated in the preceding Newtonian gravity formalisms. In gravitomagnetism, we also phenomenologically investigate the mass magnetic general relativity (GR) forces associated with the mass magnetic fields, finding that they are extremely small but non-vanishing compared to the corresponding mass electric Newtonian forces. Moreover, the directions of the mass magnetic GR forces for the solar system planets, except Venus and Uranus, are shown to be anti-parallel to those of their mass electric Newtonian forces. Next, we investigate the mass magnetic dipole moment related to the B ring of Saturn to evaluate ${\overrightarrow{m}}_M\left(Ring\right)=-1.141\times {10}^4{\mathrm{m}}^3{\mathrm{s}}^{-1}\widehat{\omega }$, with $\widehat{\omega }$ being the unit vector along the axis direction of the spinning B ring. The predicted value of ${\overrightarrow{m}}_M\left(Ring\right)$ is shown to be directly related to the Cassini data on the total mass of the rings of Saturn. Full article

Magnetorheological elastomers (MREs) are smart composite materials with tunable mechanical properties by ferromagnetic particle interactions. This study applied the microstructure-based dipole and Maxwell methods to evaluate the magneto-mechanical coupling and magnetostrictive responses of MREs, focusing on various particle distributions. The finite element modeling of representative volume elements with fixed volume fractions revealed that the straight chain microstructure exhibits the most significant magnetostrictive effect due to its low initial shear stiffness and significant magnetic force contributions. For particle separations exceeding three radii, the dipole and Maxwell methods yield consistent results for vertically or horizontally aligned particles. For particle separations greater than three radii, the dipole and Maxwell methods produce consistent results for vertically and horizontally aligned particles. However, discrepancies emerge for angled configurations and complex microstructures, with the largest deviation observed in the hexagonal particle distribution, where the two methods differ by approximately 27%. These findings highlight the importance of selecting appropriate modeling methods for optimizing MRE performance. Since anisotropic MREs with straight-chain alignments are the most widely used, our results confirm that the dipole method offers an efficient alternative to the Maxwell method for simulating these structures. Full article

Thermal relics with masses in the GeV to TeV range remain possible candidates for the Universe’s dark matter (DM). These neutral particles are often assumed to have vanishing electric and magnetic dipole moments so that they do not interact with single real photons, but the anapole moment, a static electromagnetic property whose features are akin to that of a classical toroidal solenoid, can still be non-zero, permitting interactions with single virtual photons. In some models, DM predominantly annihilates into charged standard model particles through a p-wave process mediated by the anapole moment. The anapole moment is also responsible for another interaction of interest. If a DM medium were subjected to an electric current, a DM particle whose anapole moment was aligned with the current would have lower energy than the state with an antialigned anapole moment. Given these interactions, if a collection of initially unpolarized DM particles were subjected to an electric current, then the DM medium would become partially polarized, according to the Boltzmann distribution. In such a polarized medium, DM annihilation into photons, a subdominant s-wave process realizable through higher order interactions, would be somewhat suppressed. If the local electric current existed during a time in which the DM begins to drop out of thermal equilibrium with the rest of the Universe, the suppressed annihilation could lead to a small local excess in the relic DM density relative to a current-free region. This mechanism by which the local DM density can be perturbed is novel. Using effective interactions to model a DM particle’s anapole moment and polarizabilities (responsible for s-wave annihilation into two photons), we compute the changes in the DM density produced by long- and short-lived currents around freeze out. If we employ the most stringent constraints on DM annihilation into two photons, we find that long-lived currents can result in a fractional change in the DM density on the order of ${10}^{-17}$ for DM masses around 100 GeV; for short-lived currents, this fractional change in local DM density is on the order of ${10}^{-23}$ for the same DM mass. Full article

Many tissues exhibit structural anisotropy, which imparts orientation-specific properties and functions. However, recapitulating the cellular patterns found in anisotropic tissues presents a remarkable challenge, particularly when using soft and wet hydrogels. Herein, we develop self-assembled anisotropic magnetic Fe₃O₄ micropatterns on polyethylene glycol hydrogels utilizing dipole–dipole interactions. Under the influence of a static magnetic field, Fe₃O₄ nanoparticles align into highly ordered structures with a height of 400–600 nm and a width of 8–10 μm. Furthermore, our layer-by-layer assembly technique enables the creation of oriented micropatterns with varying densities and heights, which can be further manipulated to form three-dimensional structures by adjusting the angle of the magnetic field. These anisotropic magnetic Fe₃O₄ micropatterns can be applied to various substrates, including treated glass slides, standard glass slides, silicon wafers, and polydimethylsiloxane. The patterned Fe₃O₄ scaffolds, modified with gold coating, effectively enhance cellular adhesion, orientation, and osteogenic differentiation of bone marrow-derived stem cells, which is crucial for effective tissue repair. Overall, this study presents an efficient strategy for constructing anisotropic Fe₃O₄ micropattern hydrogels, providing a bioactive platform that significantly enhances cellular functions. Full article

Currently, perfect absorption properties of metamaterials have attracted widespread interest in the area of solar energy. Ultra-broadband absorption, incidence angle insensitivity, and polarization independence are key performance indicators in the design of the absorbers. In this work, we proposed a metamaterial absorber based on the absorption mechanism with multiple resonances, including propagation surface plasmon resonance (PSPR), localized surface plasmon resonance (LSPR), electric dipole resonance (EDR), and magnetic dipole resonance (MDR). The absorber, consisting of composite nanocylinders and a microcavity, can perform solar energy full-spectrum absorption. The proposed absorber obtained high absorption (>95%) from 272 nm to 2742 nm at normal incidence. The weighted absorption rate of the absorber at air mass 1.5 direct in the wavelength range of 280 nm to 3000 nm exceeds 98.5%. The ultra-broadband perfect absorption can be ascribed to the interaction of those resonances. The photothermal conversion efficiency of the absorber reaches 85.3% at 375 K. By analyzing the influence of the structural parameters on the absorption efficiency, the absorber exhibits excellent fault tolerance. In addition, the designed absorber is insensitive to polarization and variation in ambient refractive index and has an absorption rate of more than 80% at the incident angle of 50°. Our proposed absorber has great application potential in solar energy collection, photothermal conversion, and other related areas. Full article

We introduce a new approach for describing nonstationary quantum systems with a discrete energy spectrum. The essence of this approach is that we describe the evolution of a quantum system in a time-dependent basis. In a sense, this approach is similar to the description of the system in the interaction representation. However, the time dependence of the basic states of the representation is determined not by the evolution operator with a time-independent Hamiltonian but by the eigenstates of the time-dependent Hamiltonian defined at the current time. The time dependence of the basic states of the representation leads to the appearance of an additional term in the Schrödinger equation, which in the case of slowly changing parameters of the Hamiltonian can be considered as a small perturbation. The adiabatic representation is suitable in cases where it is impossible to apply the standard interaction representation. The application of the adiabatic representation is illustrated by the example of two spins connected by a magnetic dipole–dipole interaction in a slowly varying external magnetic field. Full article

The magnetic toroidal dipole moment, which is induced by a vortex-type spin texture, manifests itself in parity-breaking physical phenomena, such as a linear magnetoelectric effect and nonreciprocal transport. We elucidate that a staggered alignment of the magnetic toroidal dipole can give rise to spontaneous magnetization even under antiferromagnetic structures. We demonstrate the emergence of uniform magnetization by considering the collinear antiferromagnetic structure with the staggered magnetic toroidal dipole moment on a bilayer zigzag chain. Based on the model calculations, we show that the interplay between the collinear antiferromagnetic mean field and relativistic spin-orbit coupling plays an important role in inducing the magnetization. Full article

Magnetorheological elastomers (MREs) are in demand in the field of high-tech microindustries and nanoindustries such as biomedical applications and soft robotics due to their exquisite magneto-sensitive response. Among various MRE applications, programmable actuators are emerging as promising soft robots because of their combined advantages of excellent flexibility and precise controllability in a magnetic system. Here, we present the development of magnetically programmable soft magnetic microarray actuators through field-induced injection molding using MREs, which consist of styrene-ethylene/butylene styrene (SEBS) elastomer and carbonyl iron powder (CIP). The ratio of the CIP/SEBS matrix was designed to maximize the CIP fraction based on a critical solids loading. Further, as part of the design of the magnetization distribution in micropillar arrays, the magnetorheological response of the molten composites was analyzed using the static and dynamic viscosity results for both the on and off magnetic states, which reflected the particle dipole interaction and subsequent particle alignment during the field-induced injection molding process. To develop a high-aspect-ratio soft magnetic microarray, X-ray lithography was applied to prepare the sacrificial molds with a height-to-width ratio of 10. The alignment of the CIP was designed to achieve a parallel magnetic direction along the micropillar columns, and consequently, the micropillar arrays successfully achieved the uniform and large bending actuation of up to approximately 81° with an applied magnetic field. This study suggests that the injection molding process offers a promising manufacturing approach to build a programmable soft magnetic microarray actuator. Full article

Concentric multiple nanorings have previously been fabricated and investigated mainly for their different static magnetization states. Here, we present a theoretical analysis for the magnetization dynamics in double nanorings arranged concentrically, where there is coupling across a nonmagnetic spacer due to the long-range dipole–dipole interactions. We employ a microscopic, or Hamiltonian-based, formalism to study the discrete spin waves that exist in the magnetic states where the individual rings may be in either a vortex or an onion state. Numerical results are shown for the frequencies and the spatial amplitudes (with relative phase included) of the spin-wave modes. Cases are considered in which the magnetic materials of the rings are the same (taken to be permalloy) or two different materials such as permalloy and cobalt. The dependence of these properties on the mean radial position of the spacer were studied, showing, in most cases, the existence of two distinct transition fields. The special cases, where the radial spacer width becomes very small (less than 1 nm) were analyzed to study direct interfaces between dissimilar materials and/or effects of interfacial exchange interactions such as Ruderman–Kittel–Kasuya–Yoshida coupling. These spin-wave properties may be of importance for magnetic switching devices and sensors. Full article