Search Results (32)

In this study, two biochar composites, namely hydroxyapatite/mulberry stem biochar (HMp) and magnesium-doped HMp (Mg0.1-HMp), were prepared using mulberry stem as the major raw material using the sol–gel process. Characterization and batch experiments were carried out on HMp and Mg0.1-HMp to investigate the Pb(II) adsorption mechanism and the factors affecting the adsorption, respectively. The results indicated that carboxylic compounds, phenols, and carbonyl functional groups were formed on the surfaces of HMp and Mg0.1-HMp. At an optimal pH of 5, an adsorption period of 6 h was achieved at an initial Pb(II) concentration of 100 mg/L and adsorbent quantity of 2 g/L. The maximum Pb(II) adsorption capacities of the HMp and Mg0.1-HMp were 303.03 and 312.50 mg/g, respectively, at 25 °C. The maximum Pb(II) adsorption capacity of Mg0.1-HMp was 2.55 times more than that of mulberry stem biochar (MBC). The adsorption of Pb(II) by HMp and Mg0.1-HMp is consistent with the Langmuir isotherm and pseudo-second-order kinetic models, demonstrating a spontaneous, endothermic, and irreversible process dominated by monolayer chemical adsorption. These results show that the mechanisms of Pb(II) by Mg0.1-HMp mainly involved electrostatic interaction, complexation, precipitation, and ion exchange. Full article

The present work investigates the rheological behavior of ceramic slurries made of hydroxyapatite powders doped with magnesium and strontium ions and selected as particularly relevant for biomedical applications. The incorporation of doping ions into the apatite crystal structure is a well-known way to enhance the bioactivity of hydroxyapatite through compositional and structural changes, however, this also affects the rheological properties relevant to the fabrication of ceramic devices by forming techniques based on the manipulation of aqueous slurries. We analyzed the effect of different apatitic chemical compositions, powder content, and dispersant amount on the shear behavior and flowability of slurries, thus finding that the structural changes in hydroxyapatite induced by ion doping significantly affected the colloidal stability of the apatite powders and the viscoelasticity of the slurries. This leads to improved rheological behavior in the hydroxyapatite suspensions, which is suitable for the future development of ceramic slurries, particularly for achieving novel ceramic devices by extrusion-based techniques. Full article

Magnesium-doped hydroxyapatite/chitosan composite coatings produced by the radio-frequency magnetron sputtering technique were exposed to 5 MeV electron beams of 8 and 30 Gy radiation doses in a linear electron accelerator. The surfaces of unirradiated layers are smooth, while the irradiated ones exhibit nano-structures with sizes that increase from 60 nm at a 8 Gy dose to 200 nm at a 30 Gy dose. Young’s modulus and the stiffness of the layers decrease from 58.9 GPa and 10 µN/nm to 5 GPa and 2.2 µN/nm, respectively, when the radiation doses are increased from 0 to 30 Gy. These data suggest the diminishing of the contribution of the chitosan to the elasticity of the magnesium-doped hydroxyapatite/chitosan composite layers after electron beam irradiation. The biological capabilities of the coatings were assessed before and after their immersion in RPMI-1640 cell culture medium for 7 and 14 days, respectively, and further cultured with a MG63 cell line (ATCC CRL1427) in Dulbecco’s Modified Eagle Medium supplemented with fetal bovine serum, penicillin–streptomycin, and L-glutamine. Thus, 1 µm spherical structures were developed on the surfaces of the layers exposed to a 30 Gy radiation dose and immersed for 14 days in the RPMI-1640 biological medium. The molecular structures of all the RPMI-1640 immersed samples were modified by the growth of a carbonated hydroxyapatite layer characterized by a B-type substitution, as Fourier Transform Infrared Spectroscopy revealed. The biological assay proved the increased biocompatibility of the layers kept in RPMI-1640 medium and enhanced MG63 cell attachment and proliferation. Atomic force microscopy analysis indicated the elongated fibroblastic cell morphology of MG63 cells with minor alteration at 30 Gy irradiation doses as a result of layer biocompatibility modifications. Full article

In this paper, we present the development of magnesium-doped hydroxyapatite in chitosan matrix (MHA_Ch) powder by an adapted coprecipitation method. The MHA_Ch powder was then deposited as thin layers by radio frequency magnetron sputtering. The MHA_Ch layers were exposed to various irradiation doses and immersed in Dulbecco’s Modified Eagle’s Medium (DMEM) for various time intervals. We report, for the first time, the effects of DMEM on irradiated layers of magnesium-doped hydroxyapatite in a chitosan matrix. The surface morphology of the layers before and after irradiation and immersion in DMEM was evaluated by SEM, AFM, and MM studies. Additionally, data about the functional groups present in the layers and the changes induced by exposure of the layers to irradiation and DMEM were obtained by FTIR studies. In vitro biological assays were conducted using an MG63 cell line (ATCC CRL1427). Our results suggest that the magnesium-doped hydroxyapatite in chitosan matrix layers may be suitable candidates for applications in the biomedical domain. Full article

Autogenous grafts remain the “gold standard” in bone tissue grafting procedures; however, limitations such as donor site morbidity, invasiveness, and limited availability have spurred research into alternative materials. Hydroxyapatite (HA), a widely used bioceramic, is known for its bioactivity and biocompatibility. Nonetheless, its inherent brittleness and porosity necessitate modifications to enhance its mechanical and functional properties. Ionic doping has emerged as a transformative strategy to improve the properties of HA by integrating ions such as strontium (Sr²⁺), magnesium (Mg²⁺), and zinc (Zn²⁺). These dopants influence HA’s crystal structure, morphology, and solubility, resulting in enhanced bioactivity, accelerated bone mineralization, and improved mechanical properties, such as increased fracture resistance and wear durability. Additionally, antimicrobial properties can be achieved through the inclusion of silver ions (Ag⁺), reducing the risk of peri-implant infections. This review focuses on the effects of ionic doping on the structure and functionality of hydroxyapatite, emphasizing advancements in tailoring its properties to clinical needs. By consolidating two decades of research, this study highlights how ionic doping bridges the gap between synthetic biomaterials and native bone, unlocking new potential in regenerative medicine and orthopedic applications. Full article

Magnesium-doped hydroxyapatite (HAp-Mg) nanofibers show promise for medical applications due to their structural similarity to bone minerals and enhanced biological properties, such as improved biocompatibility and antimicrobial activity. This study synthesized HAp-Mg nanofibers using a microwave-assisted hydrothermal method (MAHM) to evaluate their cytotoxicity, biocompatibility, and antimicrobial efficacy compared to commercial hydroxyapatite (HAp). Characterization through X-ray diffraction (XRD), scanning electron microscopy (SEM), Transmission Electron Microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR) confirmed the successful incorporation of magnesium, producing high-purity, crystalline nanofibers with hexagonal morphology. Rietveld refinement showed slight lattice parameter shortening, indicating Mg²⁺ ion integration. Cell viability assays (MTT and AlamarBlue) revealed a significant increase in fibroblast proliferation with 2% and 5% HAp-Mg concentrations compared to controls (p < 0.05), demonstrating non-cytotoxicity and enhanced biocompatibility. Antimicrobial tests (disk diffusion method, 100 µg/mL) showed that HAp-Mg had strong antibacterial effects against Gram-positive and Gram-negative bacteria and moderate antifungal activity against Candida albicans. In contrast, commercial HAp showed no antimicrobial effects. These results suggest HAp-Mg nanofibers have significant advantages as biomaterials for medical applications, particularly in preventing implant-related infections and supporting further clinical development. Full article

Background/Objectives: A biocomposite based on magnesium-doped hydroxyapatite and enriched with amoxicillin (MgHApOx) was synthesized using the coprecipitation method and is presented here for the first time. Methods: The stability of MgHAp and MgHApOx suspensions was evaluated by ultrasound measurements. The structure of the synthesized MgHAp and MgHApOx was examined with X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The crystalline structure was determined by X-ray diffraction. The FTIR data were collected in the range of 4000–400 cm⁻¹. The morphology of the nanoparticles was evaluated by scanning electron microscopy (SEM). Furthermore, the biocompatible properties of MgHAp, MgHApOx and amoxicillin (Ox) suspensions were assessed using human fetal osteoblastic cells (hFOB 1.19 cell line). The antimicrobial properties of the MgHAp, MgHApOx and Ox suspension nanoparticles were assessed using the standard reference microbial strains Staphylococcus aureus ATCC 25923, Escherichia coli ATCC 25922 and Candida albicans ATCC 10231. Results: X-ray studies have shown that the biocomposite retains the characteristics of HAp and amoxicillin. The SEM assessment exhibited that the apatite contains particles at nanometric scale with acicular flakes morphology. The XRD and SEM results exhibited crystalline nanoparticles. The average crystallite size calculated from XRD analysis increased from 15.31 nm for MgHAp to 17.79 nm in the case of the MgHApOx sample. The energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) analysis highlighted the presence of the constituent elements of MgHAp and amoxicillin. Moreover, XPS confirmed the substitution of Ca²⁺ ions with Mg²⁺ and the presence of amoxicillin constituents in the MgHAp lattice. The results of the in vitro antimicrobial assay demonstrated that MgHAp, MgHApOx and Ox suspensions exhibited good antimicrobial activity against the tested microbial strains. The results showed that the antimicrobial activity of the samples was influenced by the presence of the antibiotic and also by the incubation time. Conclusions: The findings from the biological assays indicate that MgHAp and MgHApOx are promising candidates for the development of new biocompatible and antimicrobial agents for biomedical applications. Full article

Niobium (Nb) and zirconium dioxide (ZrO₂) were doped into hydroxyapatite (HA) to fabricate HA-based composite coatings prepared on a ZK60 magnesium alloy by plasma spraying technology to improve anti-corrosion and biocompatibility for clinical applications. The results revealed that the Nb-enriched coating exhibits fewer cracks and pores with a flat surface due to the decreased temperature gradient during spraying, and small needle-like structures can fill the cracks and pores in the ZrO₂-contained coating, resulting in a more uniform and dense surface. Compared to coatings with only niobium or zirconium dioxide, the ZrO₂/Nb/HA composite coating significantly enhanced the mechanical properties and corrosion resistance of the magnesium alloys. Among all the specimens, the ZrO₂/HA coating and ZrO₂/Nb/HA coating revealed high surface hardness values (327.73 HV and 293.80 HV, respectively). However, the higher hardness value made the ZrO₂/HA coating fragile and more likely to crack, while the ZrO₂/Nb/HA coating avoided this shortcoming and exhibited a more comprehensive performance. During immersion tests, the ZrO₂/Nb/HA coating exhibited a gradual pH increase and minimal mass loss, and the cytocompatibility test demonstrated promising cellular activity. Full article

Simulated body fluid (SBF) and artificial saliva (AS) are used in biomedical and dental research to mimic the physiological conditions of the human body. In this study, the biomimetic precipitation of double-doped amorphous calcium phosphate in SBF and AS are compared by thermodynamic modelling of chemical equilibrium in the SBF/AS-CaCl₂-MgCl₂-ZnCl₂-K₂HPO₄-H₂O and SBF/AS-CaCl₂-MgCl₂-ZnCl₂-K₂HPO₄-Glycine/Valine-H₂O systems. The saturation indices (SIs) of possible precipitate solid phases at pH 6.5, close to pH of AS, pH 7.5, close to pH of SBF, and pH 8.5, chosen by us based on our previous experimental data, were calculated. The results show possible precipitation of the same salts with almost equal SIs in the two biomimetic environments at the studied pHs. A decrease in the saturation indices of magnesium and zinc phosphates in the presence of glycine is a prerequisite for reducing their concentrations in the precipitates. Experimental studies confirmed the thermodynamic predictions. Only X-ray amorphous calcium phosphate with incorporated Mg (5.86–8.85 mol%) and Zn (0.71–2.84 mol%) was obtained in the experimental studies, irrespective of biomimetic media and synthesis route. Solid-state nuclear magnetic resonance (NMR) analysis showed that the synthesis route affects the degree of structural disorder of the precipitates. The lowest concentration of dopant ions was obtained in the presence of glycine. Further, the behaviour of the selected amorphous phase in artificial saliva was studied. The dynamic of Ca²⁺, Mg²⁺, and Zn²⁺ ions between the solid and liquid phases was monitored. Both direct excitation ³¹P NMR spectra and ¹H-³¹P CP-MAS spectra proved the increase in the nanocrystalline hydroxyapatite phase upon increasing the incubation time in AS, which is more pronounced in samples with lower additives. The effect of the initial concentration of doped ions on the solid phase transformation was assessed by solid-state NMR. Full article

Magnesium, as one of the most abundant cations in the human body, plays an important role in both physiological and pathological processes. In this study, it was shown that a promising biomedical material, Mg-substituted hydroxyapatite (Mg-HA), can be synthesized via a fast mechanochemical method. For this method, the nature of magnesium-containing carriers was shown to be important. When using magnesium oxide as a source of magnesium, the partial insertion of magnesium cations into the apatite structure occurs. In contrast, when magnesium hydroxide or monomagnesium phosphate is used, single-phase Mg-HA is formed. Both experimental and theoretical investigations showed that an increase in the Mg content leads to a decrease in the lattice parameters and unit cell volume of Mg-HA. Density functional theory calculations showed the high sensitivity of the lattice parameters to the crystallographic position of the calcium site substituted by magnesium. It was shown experimentally that the insertion of magnesium cations decreases the thermal stability of hydroxyapatite. The thermal decomposition of Mg-HA leads to the formation of a mixture of stoichiometric HA, magnesium oxide, and Mg-substituted tricalcium phosphate phases. Full article

The new magnesium-doped hydroxyapatite in dextran matrix (10MgHApD) nanocomposites were synthesized using coprecipitation technique. A spherical morphology was observed by scanning electron microscopy (SEM). The X-ray diffraction (XRD) characterization results show hydroxyapatite hexagonal phase formation. The element map scanning during the EDS analysis revealed homogenous distribution of constituent elements of calcium, phosphor, oxygen and magnesium. The presence of dextran in the sample was revealed by Fourier transform infrared (FTIR) spectroscopy. The antimicrobial activity of the 10MgHAPD nanocomposites was assessed by in vitro assays using Staphylococcus aureus ATCC 25923, Pseudomonas aeruginosa ATCC 27853, Streptococcus mutans ATCC 25175, Porphyromonas gingivalis ATCC 33277 and Candida albicans ATCC 10231 microbial strains. The results of the antimicrobial assays highlighted that the 10MgHApD nanocomposites presented excellent antimicrobial activity against all the tested microorganisms and for all the tested time intervals. Furthermore, the biocompatibility assays determined that the 10MgHApD nanocomposites did not exhibit any toxicity towards Human gingival fibroblast (HGF-1) cells. Full article

A magnesium-doped hydroxyapatite in chitosan matrix (MgHApC) sample was developed as a potential platform for numerous applications in the pharmaceutical, medical, and food industries. Magnesium-doped hydroxyapatite suspensions in the chitosan matrix were obtained by the coprecipitation technique. The surface shape and morphological features were determined by scanning electron microscopy (SEM). The hydrodynamic diameter of the suspended particles was determined by Dynamic light scattering (DLS) measurements. The stability of MgHApC suspensions was evaluated by ultrasonic measurements. The hydrodynamic diameter of the MgHApC particles in suspension was 29.5 nm. The diameter of MgHApC particles calculated from SEM was 12.5 ± 2 nm. Following the SEM observations, it was seen that the MgHApC particles have a spherical shape. The Fourier-transform infrared spectroscopy (FTIR) studies conducted on MgHApC proved the presence of chitosan and hydroxyapatite in the studied specimens. In vitro antimicrobial assays were performed on Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 25923, Pseudomonas aeruginosa ATCC 27853, and Candida albicans ATCC 10231 microbial strains. The antimicrobial experiments showed that MgHApC exhibited very good antimicrobial properties against all the tested microorganisms. More than that, the results of the in vitro studies revealed that the antimicrobial properties of the samples depend on the incubation time. The evaluation of the sample’s cytotoxicity was performed using the human colon cancer (HCT-8) cell line. Our results suggested the great potential of MgHApC to be used in future applications in the field of biomedical applications (e.g., dentistry, orthopedics, etc.). Full article

Complex inorganic powders based on calcium phosphates have found a plethora of practical applications. Of particular interest are the CaO-P₂O₅ system-based multi-component material powders and granules as the source of major- and micronutrients for the plants. The emerging strategy is to use nano fertilizers based on hydroxyapatite (HAP) for phosphorus and other nutrient delivery. The doping of micronutrients into HAP structure presents an interesting challenge in obtaining specific phase compositions of these calcium phosphates. Various techniques, including mechanochemical synthesis, have been employed to fabricate doped HAP. Mechanochemical synthesis is of particular interest in this review since it presents a relatively simple, scalable, and cost-effective method of calcium phosphate powder processing. The method involves the use of mechanical force to promote chemical reactions and create nanometric powders. This technique has been successfully applied to produce HAP nanoparticles alone, and HAP doped with other elements, such as zinc and magnesium. Nanofertilizers developed through mechanochemical synthesis can offer several advantages over conventional fertilizers. Their nanoscale size allows for rapid absorption and controlled release of nutrients, which leads to improved nutrient uptake efficiency by plants. Furthermore, the tailored properties of HAP-based nano fertilizers, such as controlled porosity and degradation levels, contribute to their effectiveness in providing plant nutrition. Full article

Hydroxyapatite doped with magnesium and zinc in chitosan matrix biocomposites have great potential for applications in space technology, aerospace, as well as in the biomedical field, as a result of coatings with multifunctional properties that meet the increased requirements for wide applications. In this study, coatings on titanium substrates were developed using hydroxyapatite doped with magnesium and zinc ions in a chitosan matrix (MgZnHAp_Ch). Valuable information concerning the surface morphology and chemical composition of MgZnHAp_Ch composite layers were obtained from studies that performed scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), metallographic microscopy, and atomic force microscopy (AFM). The wettability of the novel coatings, based on magnesium and zinc-doped biocomposites in a chitosan matrix on a titanium substrate, was evaluated by performing water contact angle studies. Furthermore, the swelling properties, together with the coating’s adherence to the titanium substrate, were also analyzed. The AFM results emphasized that the composite layers exhibited the surface topography of a uniform layer, and that there were no evident cracks and fissures present on the investigated surface. Moreover, antifungal studies concerning the MgZnHAp_Ch coatings were also carried out. The data obtained from quantitative antifungal assays highlight the strong inhibitory effects of MgZnHAp_Ch against C. albicans. Additionally, our results underline that after 72 h of exposure, the MgZnHAp_Ch coatings display fungicidal features. Thus, the obtained results suggest that the MgZnHAp_Ch coatings possess the requisite properties that make them suitable for use in the development of new coatings with enhanced antifungal features. Full article

Objectives: Titanium implants are regarded as a promising treatment modality for replacing missing teeth. Osteointegration and antibacterial properties are both desirable characteristics for titanium dental implants. The aim of this study was to create zinc (Zn)-, strontium (Sr)-, and magnesium (Mg)-multidoped hydroxyapatite (HAp) porous coatings, including HAp, Zn-doped HAp, and Zn-Sr-Mg-doped HAp, on titanium discs and implants using the vapor-induced pore-forming atmospheric plasma spraying (VIPF-APS) technique. Methods: The mRNA and protein levels of osteogenesis-associated genes such as collagen type I alpha 1 chain (COL1A1), decorin (DCN), osteoprotegerin (TNFRSF11B), and osteopontin (SPP1) were examined in human embryonic palatal mesenchymal cells. The antibacterial effects against periodontal bacteria, including Porphyromonas gingivalis and Prevotella nigrescens, were investigated. In addition, a rat animal model was used to evaluate new bone formation via histologic examination and micro-computed tomography (CT). Results: The ZnSrMg-HAp group was the most effective at inducing mRNA and protein expression of TNFRSF11B and SPP1 after 7 days of incubation, and TNFRSF11B and DCN after 11 days of incubation. In addition, both the ZnSrMg-HAp and Zn-HAp groups were effective against P. gingivalis and P. nigrescens. Furthermore, according to both in vitro studies and histologic findings, the ZnSrMg-HAp group exhibited the most prominent osteogenesis and concentrated bone growth along implant threads. Significance: A porous ZnSrMg-HAp coating using VIPF-APS could serve as a novel technique for coating titanium implant surfaces and preventing further bacterial infection. Full article