Search Results (72)

A novel fluorinated diamine monomer, 4,4′-((bicyclo[2.2.1]hept- 5-ene-2,3-diylbis (methylene)) bis(oxy))bis(3- (trifluoromethyl) aniline) (NFDA), featuring a tailored alicyclic norbornane core, flexible ether linkages, and pendant trifluoromethyl groups, was successfully synthesized. This monomer was polymerized with six commercial dianhydrides to produce a series of poly(amic acid) precursors, which were subsequently converted into high-performance polyimide (PI) films via a thermal imidization process. The strategic integration of the alicyclic, ether, and fluorinated motifs within the polymer backbone resulted in materials with an exceptional combination of properties. These PI films display outstanding solubility in a wide range of organic solvents, including low-boiling options like chloroform and tetrahydrofuran, highlighting their superior solution processability. The films are amorphous and exhibit remarkable hydrophobicity, evidenced by high water contact angles (up to 109.4°) and minimal water absorption (as low as 0.26%). Furthermore, they possess excellent optical transparency, with a maximum transmittance of 86.7% in the visible region. The materials also maintain robust thermal stability, with 5% mass loss temperatures exceeding 416 °C, and offer a desirable balance of mechanical strength and flexibility. This unique set of attributes, stemming from a rational molecular design, positions these polyimides as highly promising candidates for next-generation flexible electronics and advanced photovoltaics. Full article

Two amide-preformed aromatic diamine monomers, N,N-bis(4-(3-aminobenzamido)phenyl)-N’,N’-bis(4-methoxyphenyl)-1,4-phenylenediamine (m-6) and N,N-bis(4-(4-aminobenzamido)phenyl)-N’,N’-bis(4-methoxyphenyl)-1,4-phenylenediamine (p-6), were synthesized and utilized to prepare two series of electroactive poly(amide-imide)s (PAIs) through a two-step polycondensation reaction with commercially available aromatic tetracarboxylic dianhydrides. The obtained polymers exhibited solubility in various polar organic solvents, and most of them could form transparent, flexible films via solution casting. Thermal analysis indicated glass transition temperatures (T_g) ranging from 250 °C to 277 °C, as measured by DSC, with no significant weight loss observed before 400 °C in TGA tests. Cyclic voltammograms (CV) of the polymer films on ITO-coated glass substrates revealed two reversible oxidation redox pairs between 0.67 and 1.04 V vs. Ag/AgCl in an electrolyte-containing acetonitrile solution. The PAI films showed stable redox activity with high optical contrast both in the visible and near-infrared regions, transitioning from colorless in the neutral state to green and blue in the oxidized states. Furthermore, the polymer films retained good electrochemical and electrochromic stability even after more than 100 cyclic switching operations. The PAIs displayed outstanding electrochromic performance, including high optical contrast (up to 95%), rapid response times (below 4.6 s for coloring and 5.7 s for bleaching), high coloration efficiency (up to 240 cm²/C), and low decay in optical contrast (less than 5% after 100 switching cycles for most PAIs). Full article

The operational failure of lithium-ion batteries under extreme temperatures (−40~60 °C) stems primarily from electrolyte limitations. While prior efforts improved either low-temperature or high-temperature performance independently, holistic electrolyte design with practical validation remains elusive. Herein, we develop an all-climate electrolyte (ACE) through synergistic coordination of solvent, Li salt, and additive, achieving low viscosity (<10 mPa·s at −40 °C) and high ionic conductivity (7.0 mS cm⁻¹ at −40 °C). Raman and NMR spectra reveal MA and EC co-occupying Li⁺ solvation sheath while EMC acts as a diluent, enabling rapid ion transport. Consequently, LiFePO₄ (LFP)|graphite (Gr) cell delivers unprecedented cyclability: zero capacity decay over 500 cycles at 0 °C, stable operation across −40~60 °C, and 94.1% retention after 100 cycles at 45 °C in Ah-level pouch cells. XPS and SEM analysis demonstrate lithium difluorophosphate (LiDFP) and lithium bis(fluorosulfonyl)imide (LiFSI) collaboratively remodel SEI/CEI interphases, enriching them with LiF, Li₃PO₄, and Li₂SO₄. This inorganic-dominant architecture enhances interfacial Li⁺ kinetics and all-climate stability compared to the baseline electrolyte. Our tripartite electrolyte strategy provides a material-agnostic solution for all-climate energy storage. Full article

Polyimide, a class of high-performance polymers, is renowned for its exceptional thermal stability, mechanical strength, and chemical resistance. However, in the context of high-integration and high-frequency electronic packaging, polyimides face critical challenges including relatively high dielectric constants, inadequate thermal conductivity, and mechanical brittleness. Recent advances have focused on molecular design and composite engineering strategies to address these limitations. This review first summarizes the intrinsic properties of polyimides, followed by a systematic discussion of chemical synthesis, surface modification approaches, molecular design principles, and composite fabrication methods. We comprehensively examine both conventional polymerization synthetic routes and emerging techniques such as microwave-assisted thermal imidization and chemical vapor deposition. Special emphasis is placed on porous structure engineering via solid-template and liquid-template methods. Three key modification strategies are highlighted: (1) surface modifications for enhanced hydrophobicity, chemical stability, and tribological properties; (2) molecular design for optimized dielectric performance and thermal stability; and (3) composite engineering for developing high-thermal-conductivity materials with improved mechanical strength and electromagnetic interference (EMI) shielding capabilities. The dielectric constant of polyimide is reduced while chemical stability and wear resistance can be enhanced through the introduction of fluorine groups. Ultra-low dielectric constant and high-temperature resistance can be achieved by employing rigid monomers and porous structures. Furthermore, the incorporation of fillers such as graphene and boron nitride can endow the composite materials with high thermal conductivity, excellent EMI shielding efficiency, and improved mechanical properties. Finally, we discuss representative applications of polyimide and composites in electronic device packaging, EMI shielding, and thermal management systems, providing insights into future development directions. Full article

For various applications, particularly in battery technology, there is a significant demand for uniform, high-quality lithium or lithium-coated materials. The use of electrodeposition techniques to obtain such materials has not proven practical or economical due to the low solubility of most lithium salts in suitable solvents. In this study, we propose efficient lithium electrodeposition processes and baths that can be operated at low temperatures and relatively low costs. We utilized organic solvents such as dimethyl acetamide (DMA), dimethylforamide (DMF), and dimethyl sulfoxide (DMSO), as well as a mixture of DMSO and ionic liquid [1-Butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide BMIMTFSI]. Lithium salts such as LiCl, Li₂CO₃, and LiNO₃ were tested. Lithium metal was deposited on copper substrates at different temperatures and selected current densities within an argon-filled glovebox using a DC power source or a PARSTAT-4000A potentiostat. Cyclic voltammetry (CV) was employed to determine and compare the deposition processes. The obtained deposits were analyzed through visual inspection (photography) and scanning electron microscopy (SEM). Chemical analysis (ICP-OES) and XRD confirmed the presence of lithium and occasionally lithium hydroxide in the deposits. The best results were achieved with the deposition of lithium from DMSO-LiNO₃ and DMSO-BMIMTFSI-LiNO₃ systems. Full article

Carbon dioxide, the primary greenhouse gas responsible for global warming, represents today a critical environmental challenge for humans. Mitigating CO₂ emissions and other greenhouse gases is a pressing global concern. The primary goal of this study is to investigate the potential of particular ionic liquids (ILs) in capturing CO₂ for the sweetening of natural and other gases. The solubility of CO₂ was measured in three distinct ILs, which shared a common anion (triflate, TfO) but differed in their cations. The selected ionic liquids were {1-butyl-3-methylimidazolium triflate [BMIM][TfO], 1-butyl-1-methylpyrrolidinium triflate [BMP][TfO], and 1-butyl-4-methylpyridium triflate [MBPY][TfO]}. The solvents were screened based on results from a molecular computational study that predicted low CO₂ Henry’s Law constants. Solubility measurements were conducted at 303.15 K, 323.15 K, and 343.15 K and pressures up to 1.5 MPa using a gravimetric microbalance (IGA-003). The CO₂ experimental results were modeled using the Peng–Robinson Equation of state with three mixing rules: van der Waals one (vdWI), van der Waals two (vdWII), and the non-random two-liquid (NRTL) Wong–Sandler (WS) mixing rule. For the three ILs, the NRTL-WS mixing rule regressed the data with the lowest average deviation percentage of 1.24%. The three solvents had similar alkyl chains but slightly different polarities. [MBPY][TfO], with the largest size, exhibited the highest CO₂ solubility at all three temperatures. Calculation of its relative polarity descriptor (N) shows it was the least polar of the three ILs. Conversely, [BMP][TfO] showed the highest Henry’s Law constant (lowest solubility) across the studied temperature range. Comparing the results to published data, the study concludes that triflate-based ionic liquids with three fluorine atoms had lower capacity for CO₂ compared to bis(trifluoromethylsulfonyl) imide (Tf2N)-based ionic liquids with six fluorine atoms. Additionally, the study provided data on the enthalpy and entropy of absorption. A final comparison shows that the ILs had a lower CO₂ capacity than Selexol, a solvent widely used in commercial carbon capture operations. Compared to other ILs, the results confirm that the type of anion had a more significant impact on solubility than the cation. Full article

This study presents the development of a modified polyimide (MPI) with low dielectric properties and low-temperature curing capability for high-frequency flexible printed circuit boards (FPCBs). MPI was cured using dicumyl peroxide (DCP) at 80–140 °C through a radical process optimized via DSC analysis, while Fourier-transform infrared (FT-IR) confirmed the elimination of C=C bonds and the formation of imide structures. The MPI film exhibited low dielectric constants (D_k) of 1.759 at 20 GHz and 1.734 at 28 GHz, with ultra-low dissipation factors (D_f) of 0.00165 and 0.00157. High-frequency S-parameter evaluations showed an excellent performance, with S11 of −32.92 dB and S21 of approximately −1 dB. Mechanical reliability tests demonstrated a strong peel strength of 0.8–1.2 kgf/mm (IPC TM-650 2.4.8 standard) and stable electrical resistance during bending to ~6 mm radius, with full recovery after severe deformation. These results highlight MPI’s potential as a high-performance dielectric material for next-generation FPCBs, combining superior electrical performance, mechanical flexibility, and compatibility with low-temperature processing. Full article

In this work, we present a study on the thermal/transport properties of a novel deep eutectic solvent (DES) obtained by using N-methyltrifluoroacetamide (FNMA) as the hydrogen bond donor (HBD) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as the hydrogen bond acceptor (HBA). The binary phase diagram, thermal stability, flammability, viscosity and ionic conductivity of the as-prepared DESs were investigated at atmospheric pressure. The binary phase diagram shows a range of eutectic molar ratios (x_LiTFSI = 0.2~0.33), with the lowest deep eutectic temperature of −84 °C. At x_LiTFSI = 0.2 (i.e., FNMA:LiTFSI = 4:1 and denoted as DES-4:1). The as-prepared DES composition exhibits high thermal stability (onset temperature of weight loss = 78 °C), a low viscosity (η = 48.9 mPa s at 25 °C), relatively high ionic conductivity (σ = 0.86 mS cm⁻¹ at 25 °C) and non-flammability. The transport properties, including ionic conductivity and viscosity, as a function of temperature are in accordance with the Vogel–Fulcher–Tammann (VFT) equations. With increasing molar ratio of HBD vs. HBA, the viscosity decreases, and the ionic conductivity increases at a given temperature between 25 °C and 80 °C. The roughly equal pseudo-activation energies for ion transport and viscous flow in each composition imply a strong coupling of ion transport and viscous flow. Walden plots indicate vehicular transport as the main ion transport mechanism for the DES-4:1 and DES-3:1 compositions; meanwhile, it was confirmed that the ionic conductivity and viscous flow are strictly coupled. The present work is expected to provide strategies for the development of wide-temperature-range and safer electrolytes with low salt concentrations. Full article

Organic hybrid materials are gaining traction as electrode candidates for energy storage due to their structural tunability and environmental compatibility. This study investigates polyimide/carbon nanotube/polypyrrole (PI/CNTs/PPy) hybrid nanocomposites, focusing on the correlation between thermal imidization temperature, polypyrrole deposition time, and the resulting electrochemical properties. By modulating PI processing temperatures (90 °C, 180 °C, 250 °C) and PPy deposition durations (60–700 s), this research uncovers critical structure–function relationships governing charge storage behavior. Scanning electron microscopy and electrochemical impedance spectroscopy reveal that low-temperature imidization preserves porosity and enables ion-accessible pathways, while moderate PPy deposition enhances electrical conductivity without blocking pore networks. The optimized composite, processed at 90 °C with 60 s PPy deposition, demonstrates superior specific capacitance (850 F/g), high redox contribution (~70% of total charge), low charge transfer resistance, and enhanced energy/power density. In contrast, high-temperature processing and prolonged PPy deposition result in structural densification, increased resistance, and diminished performance. These findings highlight a synergistic design approach that leverages partial imidization and controlled doping to balance ionic diffusion, electron transport, and redox activity. The results provide a framework for developing scalable, high-performance, and sustainable electrode materials for next-generation lithium-ion batteries and supercapacitors. Full article

Ionic liquids (ILs) have attracted increasing attention due to their unique physicochemical properties. Among them, 1-Methyl-1-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide, emerges as an ideal candidate for fundamental studies in electrochemical applications. This work aims to deepen the understanding of its conductivity performance, and potential interaction with added metal salts, providing insight into its applicability in advanced energy storage systems. Firstly, binary mixtures with ethylene carbonate have been prepared to improve the transport properties and select the optimal concentration of both components. Subsequently, lithium salt was added to design the adequate electrolyte. The thermal and electrochemical characterisation of these mixtures was performed by differential scanning calorimetry (DSC) thermogravimetric analysis (TGA) and Broad Band Dielectric Spectroscopy (BBDS). The results reveal a wide liquid range for the ternary systems studied, extending below −80 °C and above 120 °C. Additionally, they exhibit notably high conductivity values at room temperature (ranging from 0.2 S·m⁻¹ for the most concentrated to 0.70 S·m⁻¹ for the lowest concentrated), which highlights their suitability for advanced electrochemical applications, including but not limited to batteries. This extended liquid phase mitigates, or potentially eliminates, some of the most common issues associated with current electrolytes, such as undesired crystallisation at low temperatures. In this paper, a new promising electrolyte, consisting of a ternary mixture obtained by adding lithium salt to the eutectic composition of [C₃C₁Pyrr][TFSI] and ethyl carbonate is proposed. Full article

N-containing carbon-based materials have been employed with claimed improved performance as an adsorbent of acidic molecules, volatile organic compounds (VOC), and metallic ions; catalyst; electrocatalyst; and supercapacitor. In this context, the present work provides valuable insights into the preparation of N-doped activated carbons (ACs) by thermal treatment in NH₃ atmosphere (ammonization). A commercial AC was submitted to two kinds of pretreatment: (i) reflux with dilute HNO₃; (ii) thermal treatment up to 800 °C in inert atmosphere. The original and modified ACs were subjected to ammonization up to different temperatures. ACs with N content up to ~8% were achieved. Nevertheless, the amount and type of inserted nitrogen depended on ammonization temperature and surface composition of the starting material. Remarkably, oxygenated acidic groups on the surface of the starting material favored nitrogen insertion at low temperatures, with formation of mostly aliphatic (amines, imides, and lactams), pyridinic, and pyrrolic nitrogens. In turn, high temperatures provoked the decomposition of labile aliphatic functions. Therefore, the AC prepared from the sample pre-treated with HNO₃, which had the highest content of oxygenated acidic groups among the materials submitted to ammonization, presented the highest N content after ammonization up to 400 °C but the lowest content after ammonization up to 800 °C. Full article

Ionic Liquids (ILs) are composed of ions, usually an organic cation with an organic or inorganic anion, with a melting point below 100 °C and in most cases below room temperature. These compounds exhibit important and characteristic properties such as high ionic conductivity, good thermal and electrochemical stability and low toxicity and flammability. Subsequently, ILs have been studied as promising substitutes for conventional electrolytes for electrochemical applications, both as bulk liquids or confined in polymer matrices, commonly known as ionogels, which have the advantages of not leaking and enhancing safety and manipulation during device assembly. For this work, the ionogel of the IL 1-Ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C₂C₁Im][TFSI]) was synthesized by the polymerization of Tetramethyl orthosilicate (TMOS) and Dimethyldimethoxysilane (DMDMS). Thermal analyses of the pure ionic liquid and electrochemical response of the ionogel were studied in comparison with the corresponding bulk IL by using differential scanning calorimetry (DSC), thermogravimetry (TGA) and broad-band dielectric spectroscopy (BBDS), respectively. Full article

Phenylethynyl-terminated imide (PETI) oligomers are highly valued for their diverse applications in films, moldings, adhesives, and composite material matrices. PETIs can be synthesized at varying molecular weights, enabling the fine-tuning of their properties to meet specific application requirements. Upon thermal curing, these oligomers form super-rigid network structures that enhance solvent resistance, increase glass-transition temperatures, and improve elastic moduli. Their low molecular weights and melt viscosities further facilitate processing, making them particularly suitable for composites and adhesive bonding. This review examines recent advancements in developing ultra-high-temperature PETIs, focusing on their structure–processing–properties relationships. It begins with an overview of the historical background and key physicochemical characteristics of PETIs, followed by a detailed discussion of PETIs synthesized from monomers featuring noncoplanar configurations (including kink and cardo structures), fluorinated groups, flexible linkages, and liquid crystalline mesogenic structures. The review concludes by addressing current challenges in this research field and exploring potential future directions. Full article

Optically transparent polyimide (PI) films with good atomic oxygen (AO) resistance have been paid extensive attention as thermal controls, optical substrates for solar cells or other components for low Earth orbit (LEO) space applications. However, for common PI films, it is usually quite difficult to achieve both high optical transparency and AO resistance and maintain the intrinsic thermal stability of the PI films at the same time. In the current work, we aimed to achieve the target by using the copolymerization methodology using the fluorinated dianhydride 9,9-bis(trifluoromethyl)xanthene-2,3,6,7-tetracarboxylic dianhydride (6FCDA), the fluorinated diamine 2,2-bis [4-(4-aminophenoxy)phenyl]hexafluoropropane (BDAF) and the polyhedral oligomeric silsesquioxane (POSS)-containing diamine N-[(heptaisobutyl-POSS)propyl]-3,5-diaminobenzamide (DABA-POSS) as the starting materials. The fluoro-containing monomers were used to endow the PI films with good optical and thermal properties, while the silicon-containing monomer was used to improve the AO resistance of the afforded PI films. Thus, the 6FCDA-based PI copolymers, including 6FCPI-1, 6FCPI-2 and 6FCPI-3, were prepared using a two-step chemical imidization procedure, respectively. For comparison, the analogous PIs, including 6FPI-1, 6FPI-2 and 6FPI-3, were correspondingly developed according to the same procedure except that 6FCDA was replaced by 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA). Two referenced PI homopolymers were prepared from BDAF and 6FDA (PI-ref1) and 6FCDA (PI-ref2), respectively. The experimental results indicated that a good balance among thermal stability, optical transparency, and AO resistance was achieved by the 6FCDA-PI films. For example, the 6FCDA-PI films exhibited good thermal stability with glass transition temperatures (T_g) up to 297.3 °C, good optical transparency with an optical transmittance at a wavelength of 450 nm (T₄₅₀) higher than 62% and good AO resistance with the erosion yield (E_y) as low as 1.7 × 10⁻²⁵ cm³/atom at an AO irradiation fluence of 5.0 × 10²⁰ atoms/cm². The developed 6FCDA-PI films might find various applications in aerospace as solar sails, thermal control blankets, optical components and other functional materials. Full article

Lithium-sulfur (Li-S) batteries are a promising option for energy storage due to their theoretical high energy density and the use of abundant, low-cost sulfur cathodes. Nevertheless, several obstacles remain, including the dissolution of lithium polysulfides (LiPS) into the electrolyte and a restricted operational temperature range. This manuscript presents a promising approach to addressing these challenges. The manuscript describes a straightforward and scalable in situ thermal polymerization method for synthesizing a quasi-solid-state electrolyte (QSE) by gelling pentaerythritol tetraacrylate (PETEA), azobisisobutyronitrile (AIBN), and a dual salt lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium nitrate (LiNO₃)-based liquid electrolyte. The resulting freestanding quasi-solid-state electrolyte (QSE) effectively inhibits the polysulfide shuttle effect across a wider temperature range of −25 °C to 45 °C. The electrolyte’s ability to prevent LiPS migration and cluster formation has been corroborated by scanning electron microscopy (SEM) and Raman spectroscopy analyses. The optimized QSE composition appears to act as a physical barrier, thereby significantly improving battery performance. Notably, the capacity retention has been demonstrated to reach 95% after 100 cycles at a 2C rate. Furthermore, the simple and scalable synthesis process paves the way for the potential commercialization of this technology. Full article