Search Results (217)

The impact mechanism of long-term creep in gas-containing coal on coal and gas outbursts has not been fully elucidated and remains insufficiently understood for the purpose of disaster engineering control. This investigation conducted triaxial creep experiments on raw coal specimens under controlled confining pressures, axial stresses, and gas pressures. Through systematic analysis of coal’s physical responses across different loading conditions, we developed and validated a novel creep damage constitutive model for gas-saturated coal through laboratory data calibration. The key findings reveal three characteristic creep regimes: (1) a decelerating phase dominates under low stress conditions, (2) progressive transitions to combined decelerating–steady-state creep with increasing stress, and (3) triphasic decelerating–steady–accelerating behavior at critical stress levels. Comparative analysis shows that gas-free specimens exhibit lower cumulative strain than the 0.5 MPa gas-saturated counterparts, with gas presence accelerating creep progression and reducing the time to failure. Measured creep rates demonstrate stress-dependent behavior: primary creep progresses at 0.002–0.011%/min, decaying exponentially to secondary creep rates below 0.001%/min. Steady-state creep rates follow a power law relationship when subject to deviatoric stress (R² = 0.96). Through the integration of Burgers viscoelastic model with the effective stress principle for porous media, we propose an enhanced constitutive model, incorporating gas adsorption-induced dilatational stresses. This advancement provides a theoretical foundation for predicting time-dependent deformation in deep coal reservoirs and informs monitoring strategies concerning gas-bearing strata stability. This study contributes to the theoretical understanding and engineering monitoring of creep behavior in deep coal rocks. Full article

The development of deep coalbed methane (buried depth > 2000 m) in the Yan’an block of Ordos Basin is limited by low permeability, the pore structure of the coal reservoir, and the gas–water occurrence relationship. It is urgent to clarify the key control mechanism of pore structure on gas migration. In this study, based on high-pressure mercury intrusion (pore size > 50 nm), low-temperature N₂/CO₂ adsorption (0.38–50 nm), low-field nuclear magnetic resonance technology, fractal theory and Pearson correlation coefficient analysis, quantitative characterization of multi-scale pore–fluid system was carried out. The results show that the multi-scale pore network in the study area jointly regulates the occurrence and migration process of deep coalbed methane in Yan’an through the ternary hierarchical gas control mechanism of ‘micropore adsorption dominant, mesopore diffusion connection and macroporous seepage bottleneck’. The fractal dimensions of micropores and seepage are between 2.17–2.29 and 2.46–2.58, respectively. The shape of micropores is relatively regular, the complexity of micropore structure is low, and the confined space is mainly slit-like or ink bottle-like. The pore-throat network structure is relatively homogeneous, the difference in pore throat size is reduced, and the seepage pore shape is simple. The bimodal structure of low-field nuclear magnetic resonance shows that the bound fluid is related to the development of micropores, and the fluid mobility mainly depends on the seepage pores. Pearson’s correlation coefficient showed that the specific surface area of micropores was strongly positively correlated with methane adsorption capacity, and the nanoscale pore-size dominated gas occurrence through van der Waals force physical adsorption. The specific surface area of mesopores is significantly positively correlated with the tortuosity. The roughness and branch structure of the inner surface of the channel lead to the extension of the migration path and the inhibition of methane diffusion efficiency. Seepage porosity is linearly correlated with gas permeability, and the scale of connected seepage pores dominates the seepage capacity of reservoirs. This study reveals the pore structure and ternary grading synergistic gas control mechanism of deep coal reservoirs in the Yan’an Block, which provides a theoretical basis for the development of deep coalbed methane. Full article

The investigation of the pore structure and fractal characteristics of coal-bearing shale is critical for unraveling reservoir heterogeneity, storage-seepage capacity, and gas occurrence mechanisms. In this study, 12 representative Upper Paleozoic coal-bearing shale samples from the Yangquan Block of the Qinshui Basin were systematically analyzed through field emission scanning electron microscopy (FE-SEM), high-pressure mercury intrusion, and gas adsorption experiments to characterize pore structures and calculate multi-scale fractal dimensions (D₁–D₅). Key findings reveal that reservoir pores are predominantly composed of macropores generated by brittle fracturing and interlayer pores within clay minerals, with residual organic pores exhibiting low proportions. Macropores dominate the total pore volume, while mesopores primarily contribute to the specific surface area. Fractal dimension D₁ shows a significant positive correlation with clay mineral content, highlighting the role of diagenetic modification in enhancing the complexity of interlayer pores. D₂ is strongly correlated with the quartz content, indicating that brittle fracturing serves as a key driver of macropore network complexity. Fractal dimensions D₃–D₅ further unveil the synergistic control of tectonic activity and dissolution on the spatial distribution of pore-fracture systems. Notably, during the overmature stage, the collapse of organic pores suppresses mesopore complexity, whereas inorganic diagenetic processes (e.g., quartz cementation and tectonic fracturing) significantly amplify the heterogeneity of macropores and fractures. These findings provide multi-scale fractal theoretical insights for evaluating coal-bearing shale gas reservoirs and offer actionable recommendations for optimizing the exploration and development of Upper Paleozoic coal-bearing shale gas resources in the Yangquan Block of the Qinshui Basin. Full article

Shale and coal in the transitional marine–continental facies of the Ordos Basin serve as unconventional natural gas reservoirs, with their pore structures controlling gas adsorption characteristics and occurrence states. To quantitatively characterize the pore structure features and differences between these two reservoirs, this study takes the Shanxi Formation shale and coal in the Daning–Jixian area on the eastern margin of the Ordos Basin as examples. Field-emission scanning electron microscopy (FE-SEM), high-pressure mercury intrusion, low-temperature N₂ adsorption, and low-pressure CO₂ adsorption experiments were employed to analyze and compare the full-scale pore structures of the shale and coal reservoirs. Combined with methane isothermal adsorption experiments, the gas adsorption capacity and its differences in these reservoirs were investigated. The results indicate that the average total organic carbon (TOC) content of shale is 2.66%, with well-developed organic pores, inorganic pores, and microfractures. Organic pores are the most common, typically occurring densely and in clusters. The average TOC content of coal is 74.22%, with organic gas pores being the dominant pore type, significantly larger in diameter than those in transitional marine–continental facies shale and marine shale. In coal, micropores contribute the most to pore volume, while mesopores and macropores contribute less. In shale, mesopores dominate, followed by micropores, with macropores being underdeveloped. Both coal and shale exhibit a high SSA primarily contributed by micropores, with organic matter serving as the material basis for micropore development. The methane adsorption capacity of coal is 8–29 times higher than that of shale. Coal contains abundant organic micropores, providing a large SSA and numerous adsorption sites for methane, facilitating gas adsorption and storage. This study comprehensively reveals the similarities and differences in pore structures between transitional marine–continental facies shale and coal reservoirs in the Ordos Basin at the microscale, providing a scientific basis for the precise evaluation and development of unconventional oil and gas resources. Full article

The production of synthetic natural gas in the context of power-to-gas is a promising technology for the utilization of CO₂. Ni-based catalysts supported on carbon nanotubes (CNTs) were prepared through incipient wetness impregnation and characterized using N₂ adsorption, X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and temperature-programmed reduction (TPR). The catalysts were tested for CO₂ methanation in the 200–400 °C temperature range and at atmospheric pressure. The results demonstrated that the catalytic activity increased with the addition of the CNTs and Ni loading. The selectivity towards CH₄ was close to 100% for the Ni/ZrO₂/CNT catalysts. Reduction of the calcined catalyst at 500 °C using H₂ modified the surface chemistry of the catalyst, leading to an increase in the Ni particles. The CO₂ conversion was dependent on the Ni loading and the temperature reduction in the NiO species. The 10Ni/ZrO₂/CNT catalyst was highly stable in CO₂ methanation at 350 °C for 24 h. Thus, CNTs combined with Ni and ZrO₂ were considered promising for use as catalysts in CO₂ methanation at low temperatures. Full article

Water within coal reservoirs exerts dual effects on methane adsorption–desorption by competing for adsorption sites and reducing permeability. The bound water effect, caused by coal wettability, significantly constrains coalbed methane (CBM) production, rendering investigations into coal wettability crucial for efficient CBM development. Compared with other geological formations, coals are characterized by a highly developed microporous structure, making the CO₂ sequestration mechanism in coal seams closely linked to the microscale interactions among gas, water, and coal matrixes. However, the intrinsic mechanisms remain poorly understood. In this study, molecular dynamics simulations are employed to investigate the wettability behaviors of CO₂, CH₄, and water on different coal matrix surfaces under varying temperature and pressure conditions, for coal macromolecules representative of four coal ranks. The study reveals the evolution of water wettability in response to CO₂ and CH₄ injection, identifies wettability differences among coal ranks, and analyzes the microscopic mechanisms governing wettability. The results show the following: (1) The contact angle increases with gas pressure, and the variation in wettability is more pronounced in CO₂ environments than in CH₄. As pressure increases, the number of hydrogen bonds decreases, while the peak gas density of CH₄ and CO₂ increases, leading to larger contact angles. (2) Simulations under different temperatures for the four coal ranks indicate that temperature has minimal influence on low-rank Hegu coal, whereas for higher-rank coals, gas adsorption on the coal surface increases, resulting in reduced wettability. Interfacial tension analysis further suggests that higher temperatures reduce water surface tension, cause dispersion of water molecules, and consequently improve wettability. Understanding the wettability variations among different coal ranks under variable pressure–temperature conditions provides a fundamental model and theoretical basis for investigating deep coal seam gas–water interactions and CO₂ geological sequestration mechanisms. These findings have significant implications for the advancement of CO₂-ECBM technology. Full article

The lithofacies and pore structural characteristics of shale reservoirs directly affect the exploration and development of shale gas. To clarify the exploration and development potential of the Lower Cambrian Shuijingtuo Formation (SJT) shale in the Middle Yangtze region, China, this study employs integrated experimental approaches, including optical and scanning electron microscopy (SEM) observations, X-ray diffraction (XRD) mineralogical analysis, and low-pressure gas (N₂/CO₂) adsorption, to classify mudstone lithofacies within the SJT and elucidate pore structural characteristics and dominant geological control across different lithofacies. The research results show that (1) Six main types of shale lithofacies are found in the STJ, including low-TOC massive calcareous mudstone (LMCM), low-TOC laminated mixed mudstone (LLMM), medium-TOC massive mixed mudstone (MMMM), high-TOC massive mixed mudstone (HMMM), high-TOC laminated siliceous mudstone (HLSM), and laminated argillaceous mudstone (LAM). (2) The pore types of SJT mudstone primarily include organic pores, intragranular clay mineral pores, and microfractures. The pore structure of mudstone is mainly controlled by clay mineral content and TOC content. However, the controlling factors of pore structure vary among different mudstone lithofacies. LMCM and LLMM are dominated by intragranular clay mineral pores, with their pore structures mainly controlled by clay mineral content. The pore types of HLMM and HLSM are organic pores, with pore structures predominantly controlled by TOC content. (3) The SJT mudstone gas reservoir exhibits diverse types, including HLSM, LAM, and LLMM. HLSM is characterized by the highest brittleness index and elevated pore volume (PV) and it can be considered the optimum lithofacies in the study area. Additionally, LLMM has the highest PV and relatively high brittleness index, positioning it as another significant reservoir target in the study area. Therefore, the Lower Cambrian shale gas reservoirs in the Middle Yangtze region exhibit diverse reservoir types. These research findings provide a scientific basis for the next phase of shale gas exploration planning in the Lower Cambrian. Full article

Organic matter pores constitute a significant storage space in shale gas reservoirs, contributing to approximately 50% of the total porosity. This study employed a comprehensive approach, utilizing scanning electron microscopy, low-pressure N₂ adsorption, thermal analysis, image statistics, and fractal theory, to quantitatively characterize the structure and complexity of organic matter pores in the Wufeng–lower Longmaxi Formations (WLLFs). The WLLFs exhibit a high organic matter content, averaging 3.20%. Organic matter pores are typically well-developed, predominantly observed within organic matter clusters, organic matter–clay mineral complexes, and the internal organic matter of pyrite framboid. The morphology of these pores is generally elliptical and spindle-shaped, with the primary pore diameter displaying a bimodal distribution at 10~40 nm and 100~160 nm, potentially influenced by the observational limit of scanning electron microscopy. Shales from greater burial depths within the same gas well contain more organic matter pores; however, the development of organic matter pores in deep gas wells is roughly equivalent to that in medium and shallow gas wells. Fractal dimension values can be utilized to characterize the complexity of organic matter pores, with organic matter macropores (D_>50) being more complex than organic matter mesopores (D_2–50), which in turn are more complex than organic matter micropores (D_<2). The development of macropores and mesopores is a key factor in the heterogeneity of organic matter pores. The complexity of organic matter pores in the same well increases gradually with the burial depth of the shale, and the complexity of organic matter pores in deep gas wells is roughly equivalent to that in medium and shallow gas wells. The structure and fractal characteristics of organic matter pores in shale are primarily controlled by components, diagenesis, tectonism, etc. The lower Longmaxi shale exhibit a high biogenic quartz content and robust hydrocarbon generation from organic matter. This composition effectively shields organic matter pores from multi-directional extrusion, leading to the formation of macropores and mesopores without specific orientation. High-quality shale sections (one and two sublayers) have relatively high fractal dimension D_2–50 and D_>50 values of organic matter pores and gas content. Consequently, the quality parameters of shale and fractal dimension characteristics can be comprehensively evaluated to identify high-quality shale sections. Full article

This study presents a comprehensive multifractal characterization of full-scale pore structures in middle- to high-rank coal reservoirs from the Western Guizhou–Eastern Yunnan Basin and establishes a permeability prediction model integrating fractal heterogeneity and pore throat parameters. Eight coal samples were analyzed using mercury intrusion porosimetry (MIP), low-pressure gas adsorption (N₂/CO₂), and multifractal theory to quantify multiscale pore heterogeneity and its implications for fluid transport. Results reveal weak correlations (R² < 0.39) between conventional petrophysical parameters (ash yield, volatile matter, porosity) and permeability, underscoring the inadequacy of bulk properties in predicting flow behavior. Full-scale pore characterization identified distinct pore architecture regimes: Laochang block coals exhibit microporous dominance (0.45–0.55 nm) with CO₂ adsorption capacities 78% higher than Tucheng samples, while Tucheng coals display enhanced seepage pore development (100–5000 nm), yielding 2.5× greater stage pore volumes. Multifractal analysis demonstrated significant heterogeneity (Δα = 0.98–1.82), with Laochang samples showing superior pore uniformity (D₁ = 0.86 vs. 0.82) but inferior connectivity (D₂ = 0.69 vs. 0.71). A novel permeability model was developed through multivariate regression, integrating the heterogeneity index (Δα) and effective pore throat diameter (D₁₀), achieving exceptional predictive accuracy. The strong negative correlation between Δα and permeability (R = −0.93) highlights how pore complexity governs flow resistance, while D₁₀’s positive influence (R = 0.72) emphasizes throat size control on fluid migration. This work provides a paradigm shift in coal reservoir evaluation, demonstrating that multiscale fractal heterogeneity, rather than conventional bulk properties, dictates permeability in anisotropic coal systems. The model offers critical insights for optimizing hydraulic fracturing and enhanced coalbed methane recovery in structurally heterogeneous basins. Full article

To elucidate the gas adsorption characteristics of medium-rank coal, this study collected samples from fresh mining faces in the Qinshui Basin. A series of experiments were conducted, including low-temperature carbon dioxide adsorption, low-temperature liquid nitrogen adsorption, mercury intrusion, and methane isothermal adsorption experiments, which clarify the pore structure characteristics of medium-rank coals, reveal the gas adsorption behavior in medium-rank coal, and identify the control mechanism. The results demonstrate that the modified Dubinin–Radushkevich (D-R) isothermal adsorption model accurately describes the gas adsorption in medium-rank coal, with fitting errors remaining below 1%. Comprehensive pore structure analysis reveals that the coal pore volume consists primarily of absorption pores (<2 nm), transitional pores (10–100 nm), and seepage pores (>100 nm), while the specific surface area is predominantly contributed by absorption pores (<2 nm). At low pressures, gas molecules form monolayer adsorption on absorption pore (<2 nm) and adsorption pore (2–10 nm) surfaces. With increasing pressure, multilayer adsorption dominates. As pore filling approaches the maximum capacity, the adsorption rate decreases progressively until reaching an equilibrium, at which point the adsorption capacity attains its saturation limit. The adsorption data of the gas in medium-rank coal can be explained by the improved D-R isothermal adsorption model. The priority of gas filling in pores is different, and the absorption pore is normally better than the adsorption pore. The results provide a new idea and understanding for the further study of the coalbed gas adsorption mechanism. Full article

The heterogeneity of shale pore systems, which is controlled by thermal maturation, fundamentally governs hydrocarbon storage and migration. Artificial sequence maturity samples of Xiamaling shale were obtained through a temperature–pressure simulation experiment (350–680 °C, 15–41 MPa). In combination with low-pressure CO₂/N₂ adsorption experiments, mercury intrusion porosimetry experiments and fractal theory, the heterogeneity of the pore size distribution of micropores, mesopores and macropores in shale of different maturities was quantitatively characterized. The results reveal that the total porosity follows a four-stage evolution with thermal maturity (R_o = 0.62–3.62%), peaking at 600 °C (R_o = 3.12%). Multifractal parameters indicate that areas with a low probability density are dominant in terms of pore size heterogeneity, while monofractal parameters reflect enhanced uniform development in ultra-over maturity (R_o > 3.2%). A novel Fractal Quality Index (FQI) was proposed to integrate porosity, heterogeneity, and connectivity, effectively classifying reservoirs into low-quality, medium-quality, and high-quality sweet-spot types. The findings contribute to the mechanistic understanding of pore evolution and offer a fractal-based framework for shale gas reservoir evaluation, with significant implications for hydrocarbon exploration in unconventional resources. Full article

High-voltage electrical pulses (HVEPs), a new technology designed to enhance the permeability of coal seams, have received significant attention for their application in gas extraction from low-permeability coal seams. This study designed a high-pressure adjustable electrical pulse experimental system to investigate the effects of HVEPs on the pore structure and gas adsorption–desorption characteristics of bituminous coal samples. The results revealed that HVEPs effectively restructured pore morphology in coal samples through the opening of previously sealed and partially enclosed pores. This led to a significant increase in the average pore diameter, total pore volume, and porosity. However, the increase in total specific surface area was minimal. Moreover, the connectivity of pores was continuously enhanced. As the discharge voltage increased, the pore structure significantly improved. However, HVEP treatment slightly increased the adsorption pores (micropores and transition pores) and significantly increased the seepage pores (mesopores and macropores), which facilitated the free flow of gas within the coal samples. Additionally, HVEP treatment significantly reduced both the adsorption rate and the maximum gas adsorption capacity of the coal samples, indicating a strong inhibitory effect of HVEPs on gas adsorption. Conversely, HVEPs significantly increased the gas desorption capacity and desorption rate, suggesting that HVEPs facilitated the rapid desorption and release of gas from the coal samples. Furthermore, HVEP treatment increased the gas diffusion coefficient of the coal samples, which reduced their resistance to free diffusion after desorption and promoted gas extraction from the coal seam. Full article

Highly over-mature marine shales are distributed worldwide with substantial resource potential, yet their pore structure characteristics and controlling mechanisms remain poorly understood, hindering accurate shale gas resource prediction and efficient development. This study focuses on the Cambrian Niutitang Formation shales in the Upper Yangtze region of South China. To decipher the multiscale pore network architecture and its genetic constraints, we employ scanning electron microscopy (SEM) pore extraction and fluid intrusion methods (CO₂ and N₂ adsorption, and high-pressure mercury intrusion porosimetry) to systematically characterize pore structures in these reservoirs. The results demonstrate that the shales exhibit high TOC contents (average 4.78%) and high thermal maturity (average Ro 3.64%). Three dominant pore types were identified: organic pores, intragranular pores, and intergranular pores. Organic pores are sparsely developed with diameters predominantly below 50 nm, displaying honeycomb, slit-like, or linear morphologies. Intragranular pores are primarily feldspar dissolution voids, while intergranular pores exhibit triangular or polygonal shapes with larger particle sizes. CO₂ adsorption isotherms (Type I) and low-temperature N₂ adsorption curves (H3-H4 hysteresis) indicate wedge-shaped and slit-like pores, with pore size distributions concentrated in the 0.5–50 nm range, showing strong heterogeneity. Pore structure shows weak correlations with TOC and quartz content but a strong correlation with feldspar abundance. This pattern arises from hydrocarbon generation exhaustion and graphitization-enhanced organic pore collapse under high compaction stress, which reduces pore preservation capacity. The aulacogen tectonic setting engenders proximal sediment provenance regimes that preferentially preserve labile minerals such as feldspars. This geological configuration establishes optimal diagenetic conditions for the subsequent development of meso- and macro-scale of dissolution pores. Our findings demonstrate that feldspar-rich shales, formed in a proximal depositional system with well-developed inorganic pores, serve as favorable reservoirs for the exploration of highly over-mature marine shale gas. Full article

Shale gas is a clean and effective energy source that plays a big part in the transition from high-carbon to low-carbon energy, serving as a link for the growth of low-carbon energy in the future. Since shale rock is a heterogeneous porous material, the best production strategy is determined by a precise assessment of geological gas-in-place. Therefore, the economic and technical foresight of the production operations depends on the estimation of the adsorbed gas amount in shale resources. The isotherm curves of shale gas derived in this study were classified as type 1 isotherms, which indicates the presence of micropores in these samples. In this work, XGBoost (extreme gradient boosting) and ANN (artificial neural network) optimized with ABC (artificial bee colony) and PSO (particle swarm optimization) have been proposed to learn and then predict the methane sorption capacity (MSC) in shale based on total organic carbon (TOC), temperature, pressure, and moisture as input variables, with the gas adsorption amount of shale as the output. Statistical and graphical methods were used to compare the experimental results with the expected values. By comparison, the current work’s ANN-ABC and ANN-PSO models outperform all previous studies with higher R² values (0.9913 and 0.9954) and lower RMSE scores (0.0457 and 0.0420), respectively, indicating improved predictive accuracy and generalization ability. The findings demonstrate that, in comparison to earlier models, the suggested models provide an exceptional prediction of the adsorbed gas amount in a heterogeneous porous medium. With additional data available, it may be easily updated for wider applications. Overall, this paper shows that machine learning can be used to forecast shale gas adsorption, and a well-trained model may be incorporated into a large numerical framework to optimize shale gas production curves. Full article

Geological storage of CO₂ in coal seam is an effective way for carbon emission reduction. Evaluating the adsorption-induced swelling behavior of confined coal is essential for this carbon emission reduction strategy. Based on the thermodynamic theory and the Gibbs adsorption model, a thermodynamic method for evaluating the gas adsorption-induced swelling behavior of confined coal was established. The influences of factors such as stress, gas pressure, and the state of gas on the adsorption-induced swelling behavior of confined coal were discussed. The predicted swelling deformation from the thermodynamic method based on the ideal gas hypothesis was consistent with the experimental result only under the condition of low-pressure CO₂ (<2 MPa). The predicted swelling deformation from that method was larger than the experimental result under the condition of high-pressure CO₂ (>2 MPa). However, the method based on the real gas hypothesis always had better prediction results under both the low- and high-pressure CO₂ conditions. From the perspective of phase equilibrium and transfer, in the process of CO₂ adsorption by the confined coal, gas molecules transfer from the adsorption site of high chemical potential to the low chemical potential. Taking the real gas as ideal gas will result in the surface energy increase in the established model. Consequently, the prediction result will be larger. Therefore, for geological storage of CO₂ in coal seam, it is necessary to take the real gas state to predict the adsorption-induced swelling behavior of the coal. In the process of CO₂ adsorption by the confined coal, when its pressure is being closed to the critical pressure, capillary condensation phenomenon will occur on the pore surface of the confined coal. This can make an excessive adsorption of CO₂ by the coal. With the increase in the applied stress, the adsorption capacity and adsorption-induced swelling deformation of the confined coal decrease. Compared to N₂ with CO₂, the coal by CO₂ adsorption always shows swelling deformation under the simulated condition of ultra-high-pressure injection. However, the coal by N₂ adsorption will shows shrinking deformation due to the pore pressure effect after the equilibrium pressure. Taking the difference in the adsorption-induced swelling behavior and pore compression effect, N₂ can be mixed to improve the injectivity of CO₂. This suggests that CO₂ storage in the deep burial coal seam can be carried out by its intermittent injection under high-pressure condition along with mixed N₂. Full article