Search Results (100)

According to the United Nations Environment Programme reports, buildings are responsible for nearly 40% of energy-related emissions; therefore, energy-optimized building design is crucial to reduce the reliance on non-renewable energy sources as well as greenhouse gas emissions. The OECD reports indicate the use of Building Information Modelling (BIM) as one of the effective strategies for decarbonization of buildings, since a 3D digital representation of both physical and functional characteristics of a building can help to design a more efficient infrastructure. An efficient integration of solar energy in building design can be vital for the enhancement of energy performance in terms of heating, cooling, and lighting demand. This paper presents results of an analysis of how factors related to the use of daylight, such as automatic control of artificial lighting, external shading, or the visual absorptance of internal surfaces, influence the energy efficiency within an example room in two different climatic zones. The simulation was conducted using Design Builder software, with predefined occupancy schedules and internal heat gains, and standard EPW weather files for Warsaw and Genua climate zones. The study indicates that for the examined room, when no automatic sunshades or a lighting control system is utilized, most of the final energy demand is for cooling purposes (45–54%), followed by lighting (42–43%), with only 3–12% for heating purposes. The introduction of sunshades and/or the use of daylight allowed for a reduction of the total demand by up to half. Moreover, it was pointed out that often neglected factors, like the colour of the internal surfaces, can have a significant effect on the final energy consumption. In variants with light interior, the total energy consumption was lower by about 3–4% of the baseline demand, compared to their corresponding ones with dark surfaces. These results are consistent with previous studies on daylighting strategies and highlight the importance of considering both visual and thermal impacts when evaluating energy performance. Similarly, possible side effects of certain actions were highlighted, such as an increase in heat demand resulting from a reduced need for artificial lighting. The results of the analysis highlight the potential of a simulation-based design approach in optimizing daylight use, contributing to the broader goals of building decarbonization. Full article

The structural design of rail vehicle bodies significantly influences rail vehicle performance, passenger comfort, and operational efficiency. This study presents a comparative analysis of three key concepts of a rail vehicle body, namely a differential, an integral, and a hybrid structure, with a focus on their structural principles, material utilization, and implications for manufacturability and maintenance. Three rail vehicle body variants were developed, each incorporating a low-floor configuration to enhance accessibility and interior layout flexibility. The research explores the suitable placement of technical components such as a power unit and an air-conditioning system, and it evaluates interior layouts aimed at maximizing both passenger capacity and their travelling comfort. Key features, including door and window technologies, thermal comfort solutions, and seating arrangements, are also analyzed. The study emphasizes the importance of compromises between structural stiffness, reparability, production complexity, and passenger-oriented design considerations. A part of the research includes a proposal of three variants of a rail vehicle body frame, together with their strength analysis by means of the finite element method. These analyses identified that the maximal permissible stresses for the individual versions of the frame were not exceeded. Findings contribute to the development of more efficient, accessible, and sustainable regional passenger rail vehicles. Full article

Firstly, this paper reviews the fundamental theories of solid surface wettability and contact angle hysteresis. Subsequently, it further introduces four typical wettability-engineered surfaces with low hysteresis (superhydrophobic, superamphiphobic, super-slippery, and liquid-like smooth surfaces). Finally, it focuses on the latest research progress in the field of droplet manipulation on open planar surfaces with engineered wettability. To achieve droplet manipulation, the core driving forces primarily stem from natural forces guided by bioinspired gradient surfaces or the regulatory effects of external fields. In terms of bioinspired self-propelled droplet movement, this paper summarizes research inspired by natural organisms such as desert beetles, cacti, self-aligning floating seeds of emergent plants, or water-walking insects, which construct bioinspired special gradient surfaces to induce Laplace pressure differences or wettability gradients on both sides of droplets for droplet manipulation. Moreover, this paper further analyzes the mechanisms, advantages, and limitations of these self-propelled approaches, while summarizing the corresponding driving force sources and their theoretical formulas. For droplet manipulation under external fields, this paper elaborates on various external stimuli including electric fields, thermal fields, optical fields, acoustic fields, and magnetic fields. Among them, electric fields involve actuation mechanisms such as directly applied electrostatic forces and indirectly applied electrocapillary forces; thermal fields influence droplet motion through thermoresponsive wettability gradients and thermocapillary effects; optical fields cover multiple wavelengths including near-infrared, ultraviolet, and visible light; acoustic fields utilize horizontal and vertical acoustic radiation pressure or acoustic wave-induced acoustic streaming for droplet manipulation; the magnetic force acting on droplets may originate from their interior, surface, or external substrates. Based on these different transport principles, this paper comparatively analyzes the unique characteristics of droplet manipulation under the five external fields. Finally, this paper summarizes the current challenges and issues in the research of droplet manipulation on the open planar surfaces and provides an outlook on future development directions in this field. Full article

Prefabricated components inevitably generate numerous assembly joints during installation, with each 1 mm increase in joint width correlating to a 15–20% elevation in the annual occurrence frequency of the frost formation risk. In the Inner Mongolia Region, the water migration at wall connection interfaces during winter significantly exacerbates freeze–thaw damage due to persistent thermal gradients. A coupled heat–moisture transfer model incorporating gas–liquid–solid phase transitions was developed, with the liquid moisture content and temperature gradient as dual driving forces. A validation against internationally recognized BS EN 15026:2007 benchmark cases confirmed the model robustness. The prefabricated sandwich insulation walls reconstructed with region-specific volcanic ash materials underwent a comparative evaluation of temperature and relative humidity distributions under varied winter conditions. Furthermore, we analyze and assess the potential for freezing at connection points and identify the specific areas at risk. Synergistic effects between assembly gaps and indoor–outdoor environmental interactions on wall performance degradation were systematically assessed. The results indicated that, across all working conditions, both the temperature and relative humidity at each wall measurement point underwent periodic variations influenced by the outdoor environment. These fluctuations decreased in amplitude from the exterior to the interior, accompanied by a noticeable delay effect. Specifically, at Section 2, the wall temperatures at points B2–B8 were higher compared to those at A2–A8 of Section 1. The relative humidity gradient remained relatively stable at each measurement point, while the temperature fluctuation amplitude was smaller by 2.58 ± 0.3 °C compared to Section 1. Under subfreezing conditions, Section 1 demonstrates a marked reduction in relative humidity (Cases 1-3 and 2-3) compared to reference cases, which is indicative of internal ice crystallization. Conversely, Section 2 maintains higher relative humidity values under identical therma. These findings suggest that prefabricated building joints significantly impact indoor and outdoor wall temperatures, potentially increasing the indoor heat loss and accelerating temperature transfer during winter. Full article

This study investigates, both experimentally and theoretically, the impact of incorporating window shutters on the thermal resistance of double-glazed window units, employing computational fluid dynamics (CFD) modelling. The integration of shutters, whether installed internally or externally, introduces an additional air layer that significantly influences heat transfer between indoor and outdoor environments. This effect on the thermal performance of the transparent structure was analysed through experimental measurements under real operating conditions and numerical simulations involving fluid dynamics and energy equations for the air gaps, alongside heat conduction equations for the solid components. Fourth-kind boundary conditions, considering both radiative and conductive components of the total heat flux emanating from the building’s interior, were applied at the solid–gas interfaces. The simulation results, comparing heat transfer through double-glazed windows with and without shutters, demonstrate a substantial increase in thermal resistance, ranging from 2 to 2.5 times, upon shutter implementation. These findings underscore the effectiveness of employing shutters as a strategy to enhance the energy efficiency of windows and, consequently, the overall energy performance of buildings. This research contributes to the advancement of sustainable materials for engineering applications by providing insights into the optimisation of thermal performance in building envelopes. Full article

This study investigates the influence of input values for building energy model parameters on simulation results, with the aim of improving the reliability and sustainability of energy performance assessments. Dynamic simulations were conducted in TRNSYS for three theoretical multi-residential buildings, varying parameters such as referent model dimensions, infiltration rates, envelope thermophysical properties, and interior thermal capacitance. The case study, based in Slovenia, demonstrates that glazing-related parameters, particularly the solar heat gain coefficient (g-value), exert the most significant influence—reducing the g-value from 0.62 to 0.22 decreased simulated heating (q_H,nd) and cooling (q_C,nd) demands by 25% and 95%, respectively. In contrast, referent dimensions for modeled floor area proved least influential. For Building III (BSF = 0.36), dimensional variations altered results by less than ±1%, whereas, for Building I (BSF = 0.62), variations reached up to ±20%. In general, lower shape factors yield more robust energy models that are less sensitive to input deviations. These findings are critical for promoting resource-efficient simulation practices and ensuring that energy modeling contributes effectively to sustainable building design. Understanding which inputs warrant detailed attention supports more targeted and meaningful simulation workflows, enabling more accurate and impactful strategies for building energy efficiency and long-term environmental performance. Full article

Condensation assessment of a residential building in Changsha, China-located in the hot summer and cold winter climate zone-was conducted during the Plum Rain Season (PRS) using Energy Plus simulations and field measurements. Window-opening behaviour significantly influences indoor air quality and thermal comfort. This study specifically examines how window-opening patterns, including opening duration and opening degree, affect interior surface condensation risk in a rural residential building during PRS. Results indicate that window operational status (open/closed) exerts a dominant influence on condensation risk, while varying window opening degrees during identical opening duration showed negligible differential impacts. Critical temporal patterns emerged: morning window openings during PRS should be avoided, whereas afternoon (15:00–18:00) and nighttime (18:00–06:00) ventilation proves advantageous. Optimisation analysis revealed that implementing combined afternoon and nighttime ventilation windows (15:00–18:00 + 18:00–06:00) achieved the lowest condensation risk of 0.112 among evaluated scenarios. Furthermore, monthly-adjusted window operation strategies yielded eight recommended ventilation modes, maintaining condensation risks below 0.11 and providing occupant-tailored solutions for Changsha’s PRS conditions. These findings establish evidence-based guidelines for moisture control through optimised window operation in climate-responsive building management. Full article

The complex thermal cycles during the solidification process in metal additive manufacturing (AM) lead to the formation of high-density dislocation networks, organizing into submicron-scale cellular structures. These ultrafine structures are recognized as crucial for enhancing the mechanical properties of AM metals. In this study, we investigate the evolution of dislocation density within these cellular structures under plastic deformation and its impact on mechanical response using dislocation density-based crystal plasticity finite element (CPFE) modeling. The model incorporates the evolution of both statistically stored dislocation (SSD) and geometrically necessary dislocation (GND). Our simulations reveal that the yield and flow stresses of dislocation cell structures exceed predictions based on the rule of mixtures (ROM). Additionally, the SSD density increases at a higher rate than the GND density. Factors such as the volume fraction of the cell wall, cell diameter, and initial dislocation density difference between the cell wall and interior significantly influence GND accumulation across different regions of the cellular dislocation structures. Full article

Renewable polyurethane (PU) composites were developed using castor oil and long coir (LCF), ground coir (GCF) or cellulose fiber (CF) at PU/fiber ratios of 50/50, 60/40 and 70/30 wt/wt%, respectively. The aim was to study the influence of natural fibers on composite flexibility via thermogravimetry, differential scanning calorimetry, scanning electron microscopy and water absorption, density, tensile strength, flexural and flammability tests. The set of properties was evaluated (1) subjectively by assigning importance values to the different properties and (2) via multicriteria decision analysis (MCDA). In general, the PU composites with cellulose fiber (PU/CF) exhibited higher thermal degradation temperatures, greater tensile moduli and toughness and less flammability. The composites with the best results for both analysis methods (property set analysis) were PU/CF:60/40 wt/wt% and 70/30 wt/wt%, obtained with cellulose fiber (low lignin content) and the highest PU percentage; these were the most suitable for applications that require flexibility, such as in interior design. When comparing the different coir fiber sizes, the composites containing more long coir fiber (PU/LCF 60/40 wt/wt% and 70/30 wt/wt%) presented the best results. The results of subjective property set analysis were validated using multicriteria analysis, resulting in a simple analysis for application. Full article

This study employs the effective heat capacity method within the COMSOL simulation framework to analyze the thermal performance of double-layer phase-change walls under typical summer climatic conditions in Zhengzhou, Henan Province. The model considers a wall structure with a total thickness of 100 mm and a height of 300 mm, where the exterior surface represents the outdoor environment, the interior surface represents the indoor environment, and the top and bottom boundaries are assumed to be adiabatic. A highly refined triangular mesh ensures numerical stability and solution accuracy. Special attention is given to the influence of Micro-PCM content on thermal storage characteristics. Simulation results demonstrate that increasing the Micro-PCM content substantially enhances the thermal regulation capacity of the double-layer phase-change walls. At a Micro-PCM volume fraction of 15%, the peak temperature of the double-layer phase-change wall is reduced by 4.33 °C compared to a conventional wall, while the attenuation factor increases to 16.88. Furthermore, the mean thermal delay extends to 440 min, the temperature amplitude decreases to 1.13 °C, and the peak instantaneous heat flux is reduced to 13.24 W/m². These findings highlight the significant latent heat storage capacity and superior thermal modulation performance of double-layer phase-change walls, offering a valuable technical reference for the design of energy-efficient building envelope systems. Full article

This study investigates sustainable living through minimizing environment impact, including energy efficiency, while supporting the well-being and thermal comfort in Mediterranean dwellings, specifically in Cyprus. This research highlights the need to define indoor temperature ranges that promote energy efficiency and occupants’ thermal comfort, considering the topographic variation in the Mediterranean climate. This study aims to promote sustainable building design by improving the occupants’ well-being in Mediterranean climates. This study uses the predicted mean votes index to determine thermal comfort limits by analyzing acceptable temperature ranges in 150 residences across different topographic areas of Kyrenia, Northern Cyprus, in summer and winter. The findings indicate that optimal interior air temperatures in the study area are 28.9 °C for summer and 20.2 °C for winter. Topographic variations highlight the importance of land elevation and microclimate differences in achieving suitable indoor thermal temperature conditions. The acceptable interior temperature range during summer in the mountainous region is wider (between 24.1 °C and 28.9 °C), while the winter range is broader in the coastal region (20.2 °C to 23 °C). This study provides novel region-specific indoor temperature guidelines for Mediterranean climates, emphasizing topographic differences and their influence on thermal comfort. The guidelines assist designers and policymakers in enhancing sustainable design in Mediterranean climates. Full article

Improving microclimate conditions is a pivotal aspect of urban design, particularly in hot, arid climates, where it directly influences outdoor comfort, mitigates the urban heat island (UHI) effect, and reduces the indoor cooling energy demand. The objective of this study is to quantitatively assess the impacts of neighborhoods’ urban size when combined with compact streets’ geometry regarding the outdoor thermal comfort generated in a typical vernacular settlement of the Saharan region of Algeria. The Ksar of Al-Atteuf in the city of Ghardaïa is taken as a case study. The related interior thermal conditions of buildings assumed to be potentially affected by the urban morphology are also examined. To study the effectiveness of the two urban morphology parameters (i.e., urban size and compactness) on outdoor and indoor thermal conditions, a mixed methods approach was adopted, integrating in situ climatic measurements and dynamic simulations. Indoor temperatures were examined in a traditional house located in the core of the Ksar. Year-round operative temperature (OT) simulations were achieved using the Ladybug tool within Grasshopper, and they were complemented by the Universal Thermal Climate Index (UTCI) values calculated during peak hot and cold weeks. Furthermore, a parametric analysis was conducted, focusing on the thermal performance of the compact urban fabric by varying progressively the neighborhood sizes from 20 m, 40 m, and 60 m. The results indicate stable indoor thermal conditions across the monitored residential building, which suggests that the architectural envelope is closely affected by its immediate surroundings. On the other hand, the UTCI analysis revealed significant differences in outdoor thermal comfort since the larger urban area provides better mitigation of heat stress in summer and cold stress in winter, the improved outdoor thermal conditions generated at the neighborhood level, being proportional to the size of the urban area. The findings underscore the value of compact urban fabrics in creating climate-responsive built environments and provide further insights into sustainable urban planning and energy-efficient design practices in hot, arid regions. Full article

Sustainable energy consumption in cement production involves practises and strategies aimed at reducing energy use and minimising environmental impact. The efficiency of a cement kiln is dependent on the kiln design, fuel type, and operating temperature. In this study, a dynamic simulation analysis is used to investigate heat losses and distribution within kilns with the aim of improving energy efficiency in cement production. This study used Computational Fluid Dynamics (CFD) with Conjugate Heat Transfer, Turbulent Flow, and the Realisable k−ϵ turbulence model to simulate heat transfer within the refractory and wall systems of the kiln, evaluate the effectiveness of these systems in managing heat losses, and establish the relationship between the heat transfer coefficient (HTC) and the velocities of solid and gas phases. The simulation results indicate that a temperature gradient from the kiln’s interior to its exterior is highly dependent on the effectiveness of refractory lining in absorbing and reducing heat transfer to the outer walls. The results also confirm that different thermal profiles exist for clinker and fuel gases, with clinker temperatures consistently peaking at approximately 1450 °C, an essential condition for optimal cement-phase formation. The results also indicate that phase velocities significantly influence heat absorption and transfer. Lower velocities, such as 0.2 m/s, lead to increased heat absorption, but also elevate heat losses due to prolonged exposure. The relationship between the heat transfer coefficient (HTC) and the velocities of solid and gas phases also indicates that higher velocities improve HTC and enhance overall heat transfer efficiency, reducing energy demand. Full article

Dynamic facades allow for effective climate adaptability, representing a new trend in future building envelope design. Present research on dynamic facades often focuses solely on certain aspects of the built environment or relies entirely on simulation outcomes. Meanwhile, the real-time changing nature of dynamic facades poses challenges in accurately simulating these schemes. Therefore, it remains essential to quantify the energy consumption performances of different types of dynamic facades and their influence on the indoor environment comfort in response to ventilation, light, and thermal environment to improve energy savings. This study uses an energy management system to simulate the ability of five dynamic facades—an intelligent ventilated facade, a dynamic exterior shading, a dynamic interior shading, a buffer layer, and phase-change material (PCM) facades—to provide adequate comfort and reduce energy consumption in four climate zones in China. The simulation model of a nearly net-zero energy Solar Decathlon house “Nature Between” was validated with experimental data. Among the five dynamic facades, the energy-saving efficiency of intelligent ventilation was highest, followed by exterior shading. Compared with houses without dynamic facades, the use of the dynamic facades reduced energy consumption (and annual glare time) by 19.87% (90.65%), 22.37% (74.84%), 15.19% (72.09%), and 9.23% (75.53%) in Xiamen, Shanghai, Beijing, and Harbin, respectively. Findings regarding the dynamic facade-driven energy savings and favorable indoor environment comfort provide new and actionable insights into the design and application of dynamic facades in four climate regions in China. Full article

Ship structures may collapse or be severely deformed during a fire. To precisely assess the post-fire structural integrity of ships, in this study, a thermal–mechanical coupling data interface was created, employing a significant eddy simulation algorithm for fire dynamics and a technique to analyze the structural thermal–mechanical coupling reaction. PyroSim was utilized to build a fire scenario, exporting 3D data through the device’s own program, and then the ANSYS thermal–mechanical coupling model was employed to study the spatial temperature distribution under fire-induced conditions. Data from the three-dimensional spatial temperature field served as the boundary condition for the determination of the structural temperature burden. Building on this, an analysis was conducted on the structural response of the intricate two-story interior compartment under fire conditions. The results showed that the location of the fire source and the structural distribution of the mechanical equipment inside the cabin had a great influence on the temperature and combustion heat, followed by the ventilation conditions, while the temperature variations in the parallel dual fuel tanks were greatly influenced by the stack effect. By comparing the stress and strain of the two-layer cabin under normal and fire conditions, the damage and mechanisms associated with important positions in the cabin under fire conditions were revealed. Full article