Search Results (82)

An electrochemical aptasensor was developed for the rapid and sensitive detection of ciprofloxacin (CPX) in milk samples. The device was fabricated on a polyethylene terephthalate (PET) substrate using a screen-printing technique with carbon-based conductive ink. Gold nanoparticles (AuNPs) were incorporated to enhance aptamer immobilization and facilitate electron transfer at the electrode surface. The sensor’s analytical performance was optimized by adjusting key parameters, including AuNP volume, DNA aptamer concentration, and incubation times for both the aptamer and the blocking agent (6-mercapto-1-hexanol, MCH). Differential pulse voltammetry (DPV) measurements demonstrated a linear response ranging from 10 to 50 nmol L⁻¹ and a low detection limit of 3.0 nmol L⁻¹. When applied to real milk samples, the method achieved high recovery rates (101.4–106.7%) with a relative standard deviation below 3.1%, confirming its robustness. This disposable and cost-effective aptasensor represents a promising tool for food safety monitoring, with potential for adaptation to detect other pharmaceutical residues in dairy products. Full article

Placing printed conductive patterns onto nonplanar substrates is a challenging task. In this work, we tested a simple method for depositing inkjet-printed conductive patterns onto 3D-printed pieces with cavities and sharp edges. First, a silver nanoparticle ink was used to print conductive patterns onto a flexible and porous substrate made of electrospun polycaprolactone (PCL). Then, the printed patterns were transferred to 3D-printed pieces made of polylactic acid (PLA) by temperature-promoted adhesion. Finally, the printed patterns were cured to render them conductive. The influence of the number of printed layers on their electrical and mechanical properties was evaluated. The printed patterns were also transferred to flexible substrates, such as thermoplastic polyurethane (TPU) and polyethylene terephthalate (PET) sheets, achieving conductivity after curing. Moreover, the printed patterns were effective for modular interconnection among successive transferred patterns, since it was possible to achieve electrical contact between them during the transfer process. Full article

Effective high-aspect-ratio molds that minimize vacuum processes are becoming increasingly important for producing metalenses and other devices. To fabricate a high-aspect-ratio structure, a metal film must be used as a mask for dry etching, typically achieved via vacuum deposition. To avoid this vacuum process, we devised a method to develop an etching mask in the air using silver ink. The manufacturing method involved filling the mold with silver ink, baking it, removing silver from the convex parts of the mold with a polyethylene terephthalate film, and placing silver from the concave parts of the mold on top of the ultraviolet (UV)-cured resin using ultraviolet-nanoimprint lithography. The transferred pattern had silver on the convex parts, which was used as a mask for the oxygen dry etching of the UV-curable resin. Consequently, high-aspect-ratio resin shapes were obtained from three types of nano- and micromolds. Additionally, a high-aspect-ratio resin with silver was used as a replica mold to form a silver pattern. This process is effective and allows high-aspect-ratio patterns to be obtained from master molds. Full article

The proliferation of sophisticated counterfeiting poses critical challenges to global security and commerce, with annual losses exceeding $2.2 trillion. This paper presents a novel physics-constrained deep learning framework for high-precision security ink colorimetry, integrating three key innovations: a physics-informed neural architecture achieving unprecedented color prediction accuracy (CIEDE2000 ($\Delta E_{00}$): 0.70 ± 0.08, p < 0.001), advanced attention mechanisms improving feature extraction efficiency by 58.3%, and a Bayesian optimization framework ensuring robust parameter tuning. Validated across 1500 industrial samples under varying conditions (±2 °C, 30–80% RH), this system demonstrates substantial improvements in production efficiency with a 50% reduction in rejections, a 35% decrease in calibration time, and 96.7% color gamut coverage. These achievements establish new benchmarks for security printing applications and provide scalable solutions for next-generation anti-counterfeiting technologies, offering a promising outlook for the future. Full article

Kesterite-based semiconductors, particularly copper–zinc–tin–sulfide (CZTS), have garnered considerable attention as potential absorber layers in thin-film solar cells because of their abundance, nontoxicity, and cost-effectiveness. In this study, we explored the synthesis of Ag-alloyed CZTS (ACZTS) materials via the sol–gel method and deposited them on a transparent fluorine-doped tin oxide (FTO) back electrode. A key challenge is the selection and manipulation of metal–salt precursors, with a particular focus on the oxidation states of copper (Cu) and tin (Sn) ions. Two distinct protocols, varying the oxidation states of the Cu and Sn ions, were employed to synthesize the ACZTS materials. The transfer from the solution to the precursor film was analyzed, followed by annealing at different temperatures under a sulfur atmosphere to investigate the behavior and growth of these materials during the final stage of annealing. Our results show that the precursor transformation from solution to film is highly sensitive to the oxidation states of these metal ions, significantly influencing the chemical reactions during sol–gel synthesis and subsequent annealing. Furthermore, the formation pathway of the kesterite phase at elevated temperatures differs between the two protocols. Structural, morphological, and optical properties were characterized via X-ray diffraction (XRD), Raman spectroscopy, and scanning electron microscopy (SEM). Our findings highlight the critical role of the Cu and Sn oxidation states in the formation of high-quality kesterite materials. Additionally, we studied a novel approach for controlling the synthesis and phase evolution of kesterite materials via molecular inks, which could provide new opportunities for enhancing the efficiency of thin-film solar cells. Full article

Cement-based 3D printing provides an opportunity to create cement-based elements with a hierarchy of structures and patterns that are not easily achievable using traditional casting techniques, thereby providing new possibilities for improving thermal control and energy storage in cement-based materials. In this study, the influence of internal architecture and ink formulation on the thermal behavior of 3D-printed cement composite beams was investigated using infrared thermal imaging and a conceptual one-dimensional heat transfer model based on cooling fins in convective media. Three-dimensional printed beams with rectilinear, three-dimensional honeycomb, and Archimedean chord infill patterns and cement ink formulations with and without 5% halloysite nanoclay were exposed to a heating source at one end. The thermal behavior of the beams was found to be predominantly influenced by their internal architecture rather than the cement ink formulation, with differences in void structures and heat transfer pathways among the different architectures resulting in a hierarchy of apparent thermal conductivity. The internal architecture resulted in a reduction in apparent thermal conductivity by up to 75%, while the incorporation of halloysite nanoclay in the cement ink led to a reduction of up to 14%. Among the tested internal architecture, the rectilinear architecture showed a 10–15% higher apparent thermal conductivity compared to the three-dimensional honeycomb architecture and a 35–40% higher apparent thermal conductivity than the Archimedean architecture. The research demonstrates a promising strategy for fabricating and evaluating cement-based materials with thermal management capabilities using 3D printing methods. Full article

Flexo printing is a relief printing system, and ink transfers on the solid areas are not transferring well during the printing. That is why graininess is increasing and pinholes are occurring on the solid areas. This is a well-known issue in the flexo printing system. Micro-patterns usually eliminate these pinholes. Using correct micro-patterns allows homogeneous ink laydown and increases solid ink density. Micro-pattern holes behave like gravure cylinders on plate surfaces, and this makes for better ink transfer to the substrate. In this study, a more successful micro-pattern structure than the ones currently used was found by examining the solid ink density (SID) values and ink laydown obtained from the structure by producing eight different micro-pattern structures of 1000 LPI and 1500 LPI (line per inch) pattern screen frequencies with the same polymer structure and type. Densitometric values of solid prints made with the developed micro-patterns were measured. By eliminating the pinholes formed in solid prints and at the screen dot shapes, the ink is distributed more homogeneously without graininess. It has been determined that this results in a more stable measurement of ink density and eliminates the measurement of excess ink and low density. Full article

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a series of phosphomolybdic acid–phosphotungstic acid/ZnO/polyvinylpyrrolidone (PMoA-PWA/ZnO/PVP) hybrid films, which had different ratio of PMoA/PWA, was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer, while PMoA/PWA was the chromophore. The photochromic mechanism of the PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A₃) on A4 paper. Application tests showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words, and could replace ordinary paper to realize the reuse of paper. Full article

Flexographic printing is widely used in the packaging field, but there are still some problems in the printing of flexographic ink on non-absorbent substrates, such as low precision and unstable quality. In this paper, the printing process of flexographic ink is simulated. The interaction of fluid flow, temperature change, and solid deformation in flexographic printing is studied systematically by using the method of fluid–solid thermal coupling for the first time. The process of ink channel formation under static extrusion and fluid–solid thermal coupling was analyzed. The influences of printing pressure, printing speed, ink layer thickness, and ink viscosity on the ink channel were explored. The results show that the printing speed increases and the temperature in the stamping area increases. The printing speed is nonlinear related to the ink flow channel, the influence on the channel is slow at a low speed, the channel increases sharply at a medium and high speed, and tends to be stable at a high speed. When the printing speed is 200 m/min, the ink temperature in the stamping area is 1.5 °C higher than that at the entrance. With an increase in printing pressure, the ink flow channel width showed a trend of decreasing first and then stabilizing, and the pressure was about 0.4 MPa, showing a small fluctuation; the greater the pressure, the higher the temperature of the ink, which will change the performance of the ink and plate, causing adverse effects on the printing belt. The channel width showed obvious nonlinear characteristics with an increase and decrease in ink thickness. When the ink thickness is 30 μm, the deformation of the plate reaches the maximum, and the width of the ink circulation channel is correspondingly the widest. The change in ink viscosity has little influence on the stability of the ink’s internal flow rate and temperature field. The research results provide theoretical support for the transfer of ink printing from gravure to flexo printing. Full article

This study aims to investigate the feasibility of using paper made from eco-friendly recycled and non-woody plants in graphic technology, particularly in offset printing. Instead of changing the composition or modifying the surface properties of the paper, the focus was on enhancing the print quality by modifying the printing ink. By modifying the printing inks, the quality of the prints on recycled and non-woody paper can be optimized, which in turn reduces the need for paper made from primary fibers. This approach can expand the use of alternative materials in graphic technology and design. The objective was to optimize the print quality on these sustainable materials. Five types of uncoated paper were used, with high-quality uncoated offset paper based on virgin fibers serving as a reference. Laboratory tests of the basic and surface properties were carried out to measure the paper quality parameters that are important for offset printing. The influence of the paper composition on its optical and colorimetric properties was also investigated. The interaction between the selected papers and offset inks was examined through measurements of adhesion parameters and ink transfer, i.e., the paper’s ability to accept the ink. To enhance the applicability of the investigated papers as printing substrates in the graphic industry, SiO₂ and TiO₂ nanoparticles were added to the offset inks. The influence of the paper composition on the colorimetric properties of the prints was also investigated. The print uniformity, as an important quality characteristic, was determined by measuring the mottling index. The research findings indicate that incorporating SiO₂ and TiO₂ nanoparticles into offset inks can enhance the interaction between the paper and ink, leading to improved print quality. This study provides new perspectives on the possibilities of using recycled and non-woody plant paper in offset printing without significantly compromising the quality of the print. Full article

This paper describes the process of producing chemiresistors based on hybrid nanostructures obtained from graphene and conducting polymers. The technology of graphene presumed the following: dispersion and support stabilization based on the chemical vapor deposition technique; transfer of the graphene to the substrate by spin-coating of polymethyl methacrylate; and thermal treatment and electrochemical delamination. For the process at T = 950 °C, a better settlement of the grains was noticed, with the formation of layers predominantly characterized by peaks and not by depressions. The technology for obtaining hybrid nanostructures from graphene and conducting polymers was drop-casting, with solutions of Poly(3-hexylthiophene (P3HT) and Poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-bithiophene] (F8T2). In the case of F8T2, compared to P3HT, a 10 times larger dimension of grain size and about 7 times larger distances between the peak clusters were noticed. To generate chemiresistors from graphene–polymer structures, an ink-jet printer was used, and the metallization was made with commercial copper ink for printed electronics, leading to a structure of a resistor with an active surface of about 1 cm². Experimental calibration curves were plotted for both sensing structures, for a domain of CH₄ of up to 1000 ppm concentration in air. A linearity of the curve for the low concentration of CH₄ was noticed for the graphene structure with F8T2, presenting a sensitivity of about 6 times higher compared with the graphene structure with P3HT, which makes the sensing structure of graphene with F8T2 more feasible and reliable for the medical application of irritable bowel syndrome evaluation. Full article

Inkjet printing technology offers a unique approach to producing direct-patterned pixels without fine metal masks for active matrix displays. Organic light-emitting diodes (OLEDs) consisting of thermally activated delayed fluorescence (TADF) emitters facilitate efficient light emission without heavy metals, such as platinum and iridium. Multi-resonance TADF molecules, characterized by their small full width at half maxima (FWHM), are highly suitable for the requirements of wide color-gamut displays. Herein, host-free TADF inks with a low concentration of 1 mg/mL were developed and inkjet-printed onto a seeding layer, concurrently serving as the hole-transporting layer. Attributed to the proof-of-concept of host-free inks printed on a mixed seeding layer, a maximum external quantum efficiency of 13.1% (improved by a factor of 21.8) was achieved in the inkjet-printed OLED, with a remarkably narrow FWHM of only 32 nm. Highly efficient energy transfer was facilitated by the effective dispersion of the sensitizer around the terminal emitters. Full article

The study of plant electrophysiology offers promising techniques to track plant health and stress in vivo for both agricultural and environmental monitoring applications. Use of superficial electrodes on the plant body to record surface potentials may provide new phenotyping insights. Bacterial nanocellulose (BNC) is a flexible, optically translucent, and water-vapor-permeable material with low manufacturing costs, making it an ideal substrate for non-invasive and non-destructive plant electrodes. This work presents BNC electrodes with screen-printed carbon (graphite) ink-based conductive traces and pads. It investigates the potential of these electrodes for plant surface electrophysiology measurements in comparison to commercially available standard wet gel and needle electrodes. The electrochemically active surface area and impedance of the BNC electrodes varied based on the annealing temperature and time over the ranges of 50 °C to 90 °C and 5 to 60 min, respectively. The water vapor transfer rate and optical transmittance of the BNC substrate were measured to estimate the level of occlusion caused by these surface electrodes on the plant tissue. The total reduction in chlorophyll content under the electrodes was measured after the electrodes were placed on maize leaves for up to 300 h, showing that the BNC caused only a 16% reduction. Maize leaf transpiration was reduced by only 20% under the BNC electrodes after 72 h compared to a 60% reduction under wet gel electrodes in 48 h. On three different model plants, BNC–carbon ink surface electrodes and standard invasive needle electrodes were shown to have a comparable signal quality, with a correlation coefficient of >0.9, when measuring surface biopotentials induced by acute environmental stressors. These are strong indications of the superior performance of the BNC substrate with screen-printed graphite ink as an electrode material for plant surface biopotential recordings. Full article

Third-generation biosensors use enzymes capable of direct electron transfer (DET) to the sensor surface. They are of interest for continuous glucose monitoring in blood or interstitial fluid, but they are rarely investigated. One reason is the hindered DET of the enzymes to the metallic electrodes. In this publication, a novel method for the immobilization of cellobiose dehydrogenase (CDH) DET enzymes employing conductive poly(3,4-ethylenedioxythiophene)-poly (styrene sulfonate) (PEDOT:PSS) inks and a protective polyethylene glycol dimethacrylate (PEG-DMA) hydrogel layer on gold electrodes is reported. This layer stack showed a glucose-specific current response for voltages between −0.2 and 0.4 V in physiological PBS buffer, and enabled interference-less sensing in a solution of acetaminophen, ascorbic acid, dopamine, and uric acid at 0 V. A Michaelis–Menten fit led to a maximum current density (I_max) of 257 ± 7.9 nA/mm² and a Michaelis–Menten constant (K_m) of 28.4 ± 2.2 mM, with a dynamic range of 0.1–20 mM glucose and a limit of detection of 0.1 mM. After 16 h of continuous measurement of 20 mM glucose, the signal decreased to 60% of its initial value. Storage stability was successfully verified until up to 10 days. In summary, this paper shows a simplified approach for the fabrication of third-generation biosensors using CDH-PEDOT:PSS and PEG-DMA hydrogel inks. Full article

Photochromism refers to a reversible colour change induced by the irradiation of photochromic materials with ultraviolet (UV) or visible light that reverts to the original colour after the light source is removed. This effect arises from chemical transformations between two isomers with different absorption spectra, involving processes like proton transfer, chemical-bond formation, and isomerisation. These photochromic inks, appearing as crystalline powders with micro-sized particles, require dissolution in a suitable matrix to achieve the colour change. Photochromic inks are used in security, as functional coatings for paper and packaging, in the fabric industry, and in other ways. This study examines the influence of varying concentrations of micro-sized photochromic pigments and different ink-coating thicknesses on the photochromic effect on sustainable paperboard substrates. Artificial ageing was performed to assess the photochromic response and lightfastness in relation to pigment concentration, ink-coating thickness, and the influence of the paperboard substrates. The results of this research could contribute to enhancing knowledge on employing photochromic inks for diverse packaging applications. Full article