Search Results (8)

The issue of environmental pollution caused by wastewater discharge from fruit juice production has attracted increasing attention. However, the cost-effectiveness of conventional treatment technology remains insufficient. In this study, a gravity-driven membrane bioreactor (GDMBR) was developed to treat real fruit juice wastewater from secondary sedimentation at pressures ranging from 0.01 to 0.04 MPa without requiring backwashing or chemical cleaning, with the aim of investigating flux development and contaminant removal under low-energy conditions. The results demonstrate an initial decrease in flux followed by stabilization during long-term filtration. Moreover, the stabilized flux level achieved with the GDMBR at pressures of 0.01 and 0.02 MPa was observed to surpass that obtained at 0.04 MPa, ranging from 4 to 4.5 L/m⁻² h⁻¹. The stability of flux was positively associated with the low membrane fouling resistance observed in the GDMBR system. Additionally, the GDMBR system provided remarkable efficiencies in removing the chemical oxygen demand (COD), biological oxygen demand (BOD), ammonia (NH₄⁺-N), and total nitrogen (TN), with average removal rates of 82%, 80%, 83%, and 79%, respectively. The high biological activity and microbial community diversity within the sludge and biofilm are expected to enhance its biodegradation potential, thereby contributing to the efficient removal of contaminants. Notably, a portion of total phosphorus (TP) can be effectively retained in the reactor, which highlighted the promising application of the GDMBR process for actual fruit juice wastewater based on these findings. Full article

Fruit juice production is one of the most important branches of the food and beverage industry, considering both the market size and demand. It is also one of the largest generators of industrial wastewater, considering the large consumption of fresh water during fruit processing. Hence, the appropriate treatment strategies are of the utmost importance to minimize the environmental footprint of food industry effluents. This study aimed to investigate the valorization routes for strawberry juice production wastewater (SJPW), both in terms of nutrient recovery and a circular approach to its utilization as a medium for plant biostimulant production. The results show a low antioxidant capacity and low content of polyphenols in SJPW; however, promising results were obtained for the in vitro seed germination and tomato growth promotion when investigating a biostimulant based on Bacillus sp. BioSol021, which was cultivated using SJPW in a lab-scale bioreactor, with root and shoot length improvements of approximately 30% and 25%, respectively, compared to the control samples. The plant growth promotion (PGP) traits indicated the ability of IAA production, in a concentration of 8.55 ± 0.05 mg/L, and the enzymatic activity was evaluated as through the enzymatic activity index (EAI), achieving the following: 2.26 ± 0.04 for cellulolytic activity, 2.49 ± 0.08 for hemicellulolytic activity, 2.91 ± 0.16 for pectinolytic activity, and 1.05 ± 0.00 for proteolytic activity. This study opens a new chapter of possibilities for the development of techno-economically viable circular bioprocess solutions aimed at obtaining value-added microbial products for sustainable agriculture based on the valorization of food industry effluents thus contributing to more sustainable food production at both the agricultural and industrial levels. Full article

Pineapple is one of the most important agro-industrial sugar-based fruits in Thailand. In this study, the waste stream from pineapple cannery processing was utilised and evaluated for potential use in the production of a main biopolymer group widely known as polyhydroxyalkanoates (PHAs) through aerobic batch fermentation. Firstly, pineapple cannery waste (PCW) collected from three processing sources, pineapple juice (PAJ), peel and core juice (PCJ), and pulp-washing water (PWW), was used as a carbon source. Secondly, it was characterised and pretreated. Then, batch fermentation was performed by using the optimal condition (200 rpm agitation rate, 37 °C, and fermentation time of 72 h) under two different nutrient conditions in each type of carbon source. The results revealed that PHAs were produced during 24–72 h of fermentation without any interference. The PHAs product obtained was characterised by their properties. Interestingly, GC-MS showed homopolymer of poly 3-hydroxybutyrate (P3HB) group characteristics, such as OH, CH, and C=O; meanwhile, H¹ NMR analysis showed signals corresponding to CH₃, CH₂, and CH, respectively. Remarkably, utilising the PCW showed a high-potential cheap carbon source for the production of PHAs as well as for the treatment of wastewater from the fruit industry. Full article

Opuntia dillenii (O. dillenii) is a plant belonging to the Cactaceae family that is abundant in tropical and subtropical regions worldwide. O. dillenii is consumed as a local delicacy and has no other current use. To understand the nutritional value of O. dillenii in human health and its application in the food, cosmetic, and drug industries, this review summarizes information on the chemical compounds (pure α-pyrone compounds, flavonoids, phenolic acids, polysaccharides, minerals, fatty acids, and betalains) and biological properties (anti-diabetic, anti-hyperglycemic, antihyperlipidemic, anti-atherosclerotic, anti-inflammatory, analgesic, antimicrobial, antifungal, antiviral, anti-spermatogenic, anticancer, antilarval, anti-angiogenic, and antioxidant) of extracts from each part of the plant (fruit juice, fruit peel, cladode, and seeds) (aqueous, ethanolic, and methanolic), and seed oil. In addition, data related to the recent applications of O. dillenii in various industries (e.g., edible coatings, food supplements, cosmetics, nanoparticles, and wastewater treatment) are provided. Full article

Herein, we describe a cost-effective, efficient, sustainable, and environmentally friendly pyrolytic method for the synthesis of highly active carbon materials from Carica papaya fruit juice for the photodegradation of various pollutants, such as methylene blue (MB), in aqueous solutions using ultraviolet (UV) light. Various analytical techniques were used to examine the morphology, crystal quality, functional group chemistry, particle size distribution, and optical properties of the materials. For evaluating the performance of the newly prepared carbon material, various photocatalyst parameters were investigated, including initial dye concentration, catalyst dose, pH of dye solution, cyclic stability, and scavenger studies. The obtained findings attest that the optimal degradation efficiency of carbon material for high MB concentrations (2.3 × 10⁻⁵ M) is around 98.08%, whereas at low concentrations of MB (1.5 × 10⁻⁵ M) it reaches 99.67%. Degradation kinetics indicate that MB degrades in a first-order manner. Importantly, as the pH of the dye solution was adjusted to ~11, the degradation rate increased significantly. The scavenger study indicated that hydroxyl radicals were the predominant species involved in the degradation of MB. In addition, active surface site exposure and charge transfer were strongly associated with efficient MB degradation. On the basis of its performance, this newly developed carbon material may prove to be an excellent alternative and promising photocatalyst for wastewater treatment. Furthermore, the synthetic approach used to produce carbon material from Carica papaya fruit juice may prove useful for the development of a new generation of photoactive materials for environmentally friendly applications, as well as for the production of hydrogen from solar energy. Full article

Membrane distillation (MD) can be used in drinking water treatment, such as seawater desalination, ultra-pure water production, chemical substances concentration, removal or recovery of volatile solutes in an aqueous solution, concentration of fruit juice or liquid food, and wastewater treatment. However, there is still much work to do to determine appropriate industrial implementation. MD processes refer to thermally driven transport of vapor through non-wetted porous hydrophobic membranes, which use the vapor pressure difference between the two sides of the membrane pores as the driving force. Recently, computational fluid dynamics (CFD) simulation has been widely used in MD process analysis, such as MD mechanism and characteristics analysis, membrane module development, preparing novel membranes, etc. A series of related research results have been achieved, including the solutions of temperature/concentration polarization and permeate flux enhancement. In this article, the research of CFD applications in MD progress is reviewed, including the applications of CFD in the mechanism and characteristics analysis of different MD structures, in the design and optimization of membrane modules, and in the preparation and characteristics analysis of novel membranes. The physical phenomena and geometric structures have been greatly simplified in most CFD simulations of MD processes, so there still is much work to do in this field in the future. A great deal of attention has been paid to the hydrodynamics and heat transfer in the channels of MD modules, as well as the optimization of these modules. However, the study of momentum transfer, heat, and mass transfer mechanisms in membrane pores is rarely involved. These projects should be combined with mass transfer, heat transfer and momentum transfer for more comprehensive and in-depth research. In most CFD simulations of MD processes, some physical phenomena, such as surface diffusion, which occur on the membrane surface and have an important guiding significance for the preparation of novel membranes to be further studied, are also ignored. As a result, although CFD simulation has been widely used in MD process modeling already, there are still some problems remaining, which should be studied in the future. It can be predicted that more complex mechanisms, such as permeable wall conditions, fouling dynamics, and multiple ionic component diffusion, will be included in the CFD modeling of MD processes. Furthermore, users’ developed routines for MD processes will also be incorporated into the existing commercial or open source CFD software packages. Full article

Pectinases are a group of enzymes with broad application, including in plant fiber processing, pectic wastewater treatment, paper pulping, fruit juice extraction, and clarification. With an increasing industrial demand for these enzymes, it is useful to isolate organisms that produce large amounts of pectinase and possess wide ranges of stability factors like temperature and pH. In this study, 17 out of 29 bacteria (58.62%) from forest soil samples were pectinolytic. However, only four bacteria (S-5, S-10, S-14, and S-17) showed high pectin hydrolysis zones (ranging from 0.2 cm to 1.7 cm). These four bacteria were identified based on colony morphology, microscopic characterization, biochemical characteristics, and 16S rDNA sequencing. They were designated as Streptomyces sp. (S-5, S-14), Cellulomonas sp. (S-10), and Bacillus sp. (S-17). Interestingly, bacteria showed cellulase and xylanase activity in addition to pectinase. The quantitative assay for pectinase activity of the four isolates provided proof that they are pectinase producers and can be considered potential candidates for industrial uses. The crude enzyme extracts of these bacteria are applicable in oil and juice extraction from sesame seeds and apples, respectively. Full article

A systematic study on the solar photocatalytic hydrogen production (photoreforming) performance of M/TiO₂ (M = Au, Ag, Cu or Pt) using glucose as a model substrate, and further extended to lignocellulose hydrolysates and wastewaters, is herein presented. Three metal (M) co-catalyst loading methods were tested. Variation of the type of metal results in significantly dissimilar H₂ production rates, albeit the loading method exerts an even greater effect in most cases. Deposition-precipitation (followed by hydrogenation) or photodeposition provided better results than classical impregnation (followed by calcination). Interestingly, copper as a co-catalyst performed satisfactorily as compared to Au, and slightly below Pt, thus representing a realistic inexpensive alternative to noble metals. Hydrolysates of either α-cellulose or rice husks, obtained under mild conditions (short thermal cycles at 160 °C), were rich in saccharides and thus suitable as feedstocks. Nonetheless, the presence of inhibiting byproducts hindered H₂ production. A novel photocatalytic UV pre-treatment method was successful to initially remove the most recalcitrant portion of these minor products along with H₂ production (17 µmol g_cat⁻¹ h⁻¹ on Cu/TiO₂). After a short UV step, simulated sunlight photoreforming was orders of magnitude more efficient than without the pre-treatment. Hydrogen production was also directly tested on two different wastewater streams, that is, a municipal influent and samples from operations in a fruit juice producing plant, with remarkable results obtained for the latter (up to 115 µmol g_cat⁻¹ h⁻¹ using Au/TiO₂). Full article