Search Results (28)

In comparison to shallow coal seams, deep coal seams exhibit characteristics of high temperature, pressure, and in-situ stress, leading to significant differences in reservoir properties that constrain the effective development of deep coalbed methane (CBM). This study takes the Carboniferous deep 8# coal seam in the Yulin area of Ordos basin as the research subject. Based on the test results from core drilling wells, a comprehensive analysis of the characteristics and variation patterns of coal reservoir properties and a comparative analysis of the exploration and development potential of deep CBM are conducted, aiming to provide guidance for the development of deep CBM in the Ordos basin. The research results indicate that the coal seams are primarily composed of primary structure coal, with semi-bright to bright being the dominant macroscopic coal types. The maximum vitrinite reflectance (R_o,max) ranges between 1.99% and 2.24%, the organic is type III, and the high Vitrinite content provides a substantial material basis for the generation of CBM. Longitudinally, influenced by sedimentary environment and plant types, the lower part of the coal seam exhibits higher Vitrinite content and fixed carbon (FC_ad). The pore morphology is mainly characterized by wedge-shaped/parallel plate-shaped pores and open ventilation pores, with good connectivity, which is favorable for the storage and output of CBM. Micropores (<2 nm) have the highest volume proportion, showing an increasing trend with burial depth, and due to interlayer sliding and capillary condensation, the pore size (<2 nm) distribution follows an N shape. The full-scale pore heterogeneity (fractal dimension) gradually increases with increasing buried depth. Macroscopic fractures are mostly found in bright coal bands, while microscopic fractures are more developed in Vitrinite, showing a positive correlation between fracture density and Vitrinite content. The porosity and permeability conditions of reservoirs are comparable to the Daning–Jixian block, mostly constituting oversaturated gas reservoirs with a critical depth of 2400–2600 m and a high proportion of free gas, exhibiting promising development prospects, and the middle and upper coal seams are favorable intervals. In terms of resource conditions, preservation conditions, and reservoir alterability, the development potential of CBM from the Carboniferous deep 8# coal seam is comparable to the Linxing block but inferior to the Daning–Jixian block and Baijiahai uplift. Full article

The production of gas and condensate from liquid-rich shale reservoirs, particularly within heterogeneous lacustrine systems, remains a critical challenge in unconventional hydrocarbon exploration due to intricate multiphase hydrocarbon partitioning, including gases (C₁–C₂), volatile liquids (C₃–C₇), and heavier liquids (C₇₊). This study investigates a 120-meter-thick interval dominated by lacustrine deposits from the Lower Cretaceous Shahezi Formation (K₁sh) in the Songliao Basin. This interval, characterized by high clay mineral content and silicate–pyrite laminations, was examined to identify the factors controlling hybrid shale gas condensate systems. We proposed the Hybrid Shale Condensate Index (HSCI), defined as the molar ratios of (C₁–C₇)/C₇₊, to categorize fluid phases and address shortcomings in traditional GOR/API ratios. Over 1000 samples were treated by geochemical pyrolysis logging, X-ray fluorescence (XRF) spectrum element logging, SEM-based automated mineralogy, and in situ gas desorption, revealing four primary controls: (1) Thermal maturity thresholds. Mature to highly mature shales exhibit peak condensate production and the highest total gas content (TGC), with maximum gaseous and liquid hydrocarbons at T_max = 490 °C. (2) Lithofacies assemblage. Argillaceous shales rich in mixed carbonate and clay minerals exhibit an intergranular porosity of 4.8 ± 1.2% and store 83 ± 7% of gas in intercrystalline pore spaces. (3) Paleoenvironmental settings. Conditions such as humid climate, saline water geochemistry, anoxic bottom waters, and significant input of volcanic materials promoted organic carbon accumulation (TOC reaching up to 5.2 wt%) and the preservation of organic-rich lamination. (4) Laminae and fracture systems. Silicate laminae account for 78% of total pore space, and pyrite laminations form interconnected pore networks conducive to gas storage. These findings delineate the “sweet spots” for unconventional hydrocarbon reservoirs, thereby enhancing exploration for gas condensate in lacustrine shale systems. Full article

In view of the flow zoning phenomenon existing in condensate gas reservoirs and the complex pore structure and strong heterogeneity of carbonate rock reservoirs, this study investigates the pressure dynamic behavior during the development process of such gas reservoirs by establishing corresponding models. The model divides the reservoir into three zones. The fluid flow patterns and reservoir physical property characteristics in the three regions are different. In particular, the fracture system in zone 1 has permeability stress sensitivity. The model is solved and the sensitivity analysis of the key parameters is carried out. The research results show that reservoir flow can be divided into 12 stages. Stress sensitivity affects all stages except the wellbore storage stage and becomes increasingly obvious over time. The closed boundary causes fracture closure from the lack of external energy, reducing effective flow channels and triggering the boundary response stage earlier. The increased condensate oil increases the flow resistance and pressure loss, and shortens the duration of the flow stage. The research suggests that improving reservoir conditions and enhancing fluid fluidity can reduce pressure loss and increase production capacity, providing valuable theoretical and practical guidance for the development of carbonate rock condensate gas reservoirs. Full article

The Bozi 3 reservoir is an ultra-deep condensate reservoir (−7800 m) with a high temperature (138.24 °C) and high pressure (104.78 MPa), leading to complex phase behaviors. Few PVT studies could be referred in the literature to meet such high temperature and pressure conditions. Furthermore, it is questionable regarding the applicability of existing condensate production techniques to such a high temperature and pressure reservoir. This study first characterized the phase behavior via PVT experiments and EOS tuning. The operating conditions were then optimized through reservoir numerical simulation. Results showed that: (1) the critical condensate temperature and pressure of Bozi 3 condensate gas were 326.24 °C and 43.83 MPa, respectively; (2) four gases (methane, recycled dry gas, carbon dioxide, and nitrogen) were analyzed, and methane was identified as the optimal injection gas; (3) gas injection started when the production began to fall and achieved higher recovery than gas injection started when the pressure fell below the dew-point pressure; (4) simultaneous injection of methane at both the upper and lower parts of the reservoir can effectively produce condensate oil over the entire block. This scheme achieved 8690.43 m³ more oil production and 2.75% higher recovery factor in comparison with depletion production. Full article

The Dina 2 gas field in the Kuqa Depression of the Tarim Basin is one of China’s most critical oil and gas exploration areas. Natural fractures have played an important role in the low-permeability reservoirs in the Tarim area. Tectonic fractures are dominant in such reservoirs. In fact, the factors influencing tectonic fracture development have always been the source of important issues in tight reservoirs. Cores, thin sections, and borehole image logs were used to analyze the types, basic characteristics, and factors influencing tectonic fractures in the tight sandstone reservoirs of the Dina 2 gas field in the Tarim Basin. The results showed that the tectonic fractures are dominated by high-angle and upright shearing fractures, and they mainly show ENE–WSW strikes. The thin sections suggest that 60% of the fractures are fully filled with minerals, 20% are unfilled, and 20% are partially filled. The analysis also shows that lithology, faults, and in situ stress are the main factors controlling the development of the tectonic structures. Furthermore, the correlation between the unimpeded flow from a single well and the apertures of the tectonic fractures indicates that tectonic fractures play an important role in the production of hydrocarbons. Full article

Multiple types of reservoirs, including volatile oil reservoirs, condensate gas reservoirs, and dry gas reservoirs, have been discovered in ultra-deep layers buried at depths greater than 7500 m. Understanding the genetic types of natural gas is of utmost importance in evaluating oil and gas exploration potential. The cumulative proved reserves of the super deep layer in the Shuntuoguole low uplift area of the Tarim Basin exceed 1 × 10⁸ t (oil equivalent). The origin, source, and accumulation characteristics of natural gas still remain a subject of controversy. By analyzing the composition and carbon isotope of natural gas, a detailed investigation was conducted to examine the unique geochemical and reservoir formation characteristics of the Ordovician ultra-deep natural gas within different fault zones in the middle region of the Shuntuoguole low uplift. It was determined that most of the natural gas in this area is displaying a characteristic of wet gas with a drying coefficient ranging from 0.41 to 0.99. The carbon isotope composition of methane in the gas reservoir shows relatively light values, ranging from −49.4‰ to −42‰. The carbon and hydrogen isotopes of the components are distributed in a positive order. The natural gas is oil type gas, which is derived from marine sapropelic organic matter and has a good correspondence with the lower Yuertusi formation. The maturity of natural gas in Shunbei No. 1 and No. 5 fault zones is about 1.0%, which is the associated gas of normal crude oil, while the maturity of No. 4 and No. 8 fault zones is higher than 1.0%, which is the mixture of kerogen pyrolysis gas and crude oil pyrolysis gas. The variations in the drying coefficient and carbon isotope composition of the natural gas provide evidence for the migration patterns within the Shuntuoguole low uplift central region. It indicates that the Shunbei No. 5 and No. 8 fault zones have likely migrated from south to north, while the No. 4 fault zone has migrated from the middle to both the north and south sides. These migration patterns are primarily controlled by high and steep strike-slip faults, which facilitate the vertical migration of natural gas along fault planes. Consequently, the gas accumulates in fractured and vuggy reservoirs within the Ordovician formation. Full article

The HZ 26-B buried hill reservoir is located in the eastern part of the South China Sea. This reservoir is characterized by the development of natural fractures, a high density, and a complex geological structure, featuring an upper condensate gas layer and a lower volatile oil layer. These characteristics present significant challenges for oilfield exploration. To address these challenges, this study employed advanced embedded discrete fracture methods to conduct comprehensive numerical simulations of the fractured buried hill reservoirs. By meticulously characterizing the flow mechanisms within these reservoirs, the study not only reveals their unique characteristics but also establishes an embedded discrete fracture numerical model at the oilfield scale. Furthermore, a combination of single-factor sensitivity analysis and the Pearson correlation coefficient method was used to identify the primary controlling factors affecting the development of complex condensate reservoirs in ancient buried hills. The results indicate that the main factors influencing the production capacity are the matrix permeability, geomechanical effects, and natural fracture length. In contrast, the impact of the threshold pressure gradient and bottomhole flow pressure is relatively weak. This study’s findings provide a scientific basis for the efficient development of the HZ 26-B oilfield and offer valuable references and insights for the exploration and development of similar fractured buried hill reservoirs. Full article

Tight sandstone gas has become an important field of natural gas development in China. The tight sandstone gas resources of Yan’an gas field in Ordos Basin have made great progress. However, due to the complex gas–water relationship, its exploration and development have been seriously restricted. The occurrence state of water molecules in tight reservoirs, the dynamic change characteristics of gas–water two-phase seepage and its main controlling factors are still unclear. In this paper, the water-occurrence state, gas–water two-phase fluid distribution and dynamic change characteristics of different types of tight reservoir rock samples in Yan’an gas field were studied by means of water vapor isothermal adsorption experiment and nuclear magnetic resonance methane flooding experiment, and the main controlling factors were discussed. The results show that water molecules in different types of tight reservoirs mainly occur in clay minerals and their main participation is in the formation of fractured and parallel plate pores. The adsorption characteristics of water molecules conform to the Dent model; that is, the adsorption is divided into single-layer adsorption, multi-layer adsorption and capillary condensation. In mudstone, limestone and fine sandstone, water mainly occurs in small-sized pores with a diameter of 0.001 μm–0.1 μm. The dynamic change characteristics of gas and water are not obvious and no longer change under 7 MPa displacement pressure, and the gas saturation is low. The gas–water dynamic change characteristics of conglomerate and medium-coarse sandstone are obvious and no longer change under 9 MPa displacement pressure. The gas saturation is high, and the water molecules mainly exist in large-sized pores with a diameter of 0.1 μm–10 μm. The development of organic matter in tight reservoir mudstone is not conducive to the occurrence of water molecules. Clay minerals are the main reason for the high water saturation of different types of tight reservoir rocks. Tight rock reservoirs with large pore size and low clay mineral content are more conducive to natural gas migration and occurrence, which is conducive to tight sandstone gas accumulation. Full article

Gas injection for enhanced oil and gas reservoir recovery is a crucial method in offshore Carbon Capture, Utilization, and Storage (CCUS). The B6 buried hill condensate gas reservoir, characterized by high CO₂ content, a deficit in natural energy, developed fractures and low-pressure differentials between formation and saturation pressures, requires supplementary formation energy to mitigate retrograde condensation near the wellbore area through gas injection. However, due to the connected fractures, the B6 gas reservoir exhibits strong horizontal and vertical heterogeneity, resulting in severe gas channeling and a futile cycle, which affects the gas injection efficiency at various levels of fracture development. Based on these findings, we conducted gas injection experiments and numerical simulations on fractured cores. A characterization method for oil and gas relative permeability considering dissolution was established. Additionally, the gas injection development boundary for this type of condensate gas reservoir was quantified according to the degree of fracture development, and the gas injection mode of the B6 reservoir was optimized. Research indicates that the presence of fractures leads to the formation of a dominant gas channel; the greater the permeability difference, the poorer the gas injection effect. The permeability gradation (fracture permeability divided by matrix permeability) in the gas injection area should be no higher than 15; gas injection in wells A1 and A2 is likely to achieve a better development effect under the existing well pattern. Moreover, early gas injection timing and pulse gas injection prove beneficial in enhancing the recovery rate of condensate oil. The study offers significant guidance for the development of similar gas reservoirs and for reservoirs with weakly connected fractures; advancing the timing of gas injection can mitigate the retrograde condensation phenomenon, whereas initiating gas injection after depletion may reduce the impact of gas channeling for reservoirs with strongly connected fractures. Full article

During the depletion development of condensate gas reservoirs, when the formation pressure drops below the dew point pressure, the condensate oil and natural gas systems are in the non-equilibrium state of foggy retrograde condensation. The rational use of the non-equilibrium phase characteristics of the foggy retrograde condensation phenomenon during the development process will be beneficial to the recovery of condensate oil and natural gas. In order to clarify the retrograde condensation control mechanism during the non-equilibrium depletion development of condensate gas reservoirs, the phase characteristics of a condensate oil and gas system were studied by constant composition expansion and constant volume depletion experiments. Then, on the basis of a long core depletion experiment and chromatographic analysis experiment, the influence of different pressure drop speeds, fluid properties, and reservoir physical properties on the control effect of non-equilibrium retrograde condensation after the coupling of the fluid retrograde condensation and reservoir core is analyzed. The results show that during the pressure decline process, the condensate oil and gas system will produce a strong foggy retrograde condensation phenomenon, with the saturation of the retrograde condensate increasing and then decreasing. The cumulative recovery of the condensate oil and natural gas, as well as the mass fraction of the heavy components in the condensate oil, increase with the increase in the depletion rate. Different fluid properties and reservoir physical properties have a great influence on the cumulative recovery degree of the condensate oil, and have little influence on the recovery degree of the natural gas. This work has a certain guiding role for the stable production and enhanced recovery of fractured condensate gas reservoirs in subsurface structures of metamorphic rocks. Full article

The largest marine carbonate oilfield and gas condensate field in China have been found in the Ordovician limestones in the central Tarim Basin. They are defined as large “layered” reef-shoal and karstic reservoirs. However, low and/or unstable oil/gas production has been a big challenge for effective exploitation in ultra-deep (>6000 m) reservoirs for more than 20 years. Together with the static and dynamic reservoir data, we have a review of the unconventional characteristics of the oil/gas fields in that: (1) the large area tight matrix reservoir (porosity less than 5%, permeability less than 0.2 mD) superimposed with localized fracture-cave reservoir (porosity > 5%, permeability > 2 mD); (2) complicated fluid distribution and unstable production without uniform oil/gas/water interface in an oil/gas field; (3) about 30% wells in fractured reservoirs support more than 80% production; (4) high production decline rate is over 20% per year with low recovery ratio. These data suggest that the “sweet spot” of the fractured reservoir rather than the matrix reservoir is the major drilling target for ultra-deep reservoir development. In the ultra-deep pre-Mesozoic reservoirs, further advances in horizontal drilling and large multiple fracturing techniques are needed for the economic exploitation of the matrix reservoirs, and seismic quantitative descriptions and horizontal drilling techniques across the fault zones are needed for oil/gas efficient development from the deeply fractured reservoirs. Full article

With the continuous development of conventional oil and gas resources, the strategic transformation of energy structure is imminent. Shale condensate gas reservoir has high development value because of its abundant reserves. However, due to the multi-scale flow of shale gas, adsorption and desorption, the strong stress sensitivity of matrix and fractures, the abnormal condensation phase transition mechanism, high-speed non-Darcy seepage in artificial fractures, and heterogeneity of reservoir and multiphase flows, the multi-scale nonlinear seepage mechanisms are extremely complicated in shale condensate gas reservoirs. A certain theoretical basis for the engineering development can be provided by mastering the percolation law of shale condensate gas reservoirs, such as improvement of productivity prediction and recovery efficiency. The productivity evaluation method of shale condensate gas wells based on empirical method is simple in calculation but poor in reliability. The characteristic curve analysis method has strong reliability but a great dependence on the selection of the seepage model. The artificial intelligence method can deal with complex data and has a high prediction accuracy. Establishing an efficient shale condensate gas reservoir development simulation technology and accurately predicting the production performance of production wells will help to rationally formulate a stable and high-yield mining scheme, so as to obtain better economic benefits. Full article

The dynamic productivity prediction of shale condensate gas reservoirs is of great significance to the optimization of stimulation measures. Therefore, in this study, a dynamic productivity prediction method for shale condensate gas reservoirs based on a convolution equation is proposed. The method has been used to predict the dynamic production of 10 multi-stage fractured horizontal wells in the Duvernay shale condensate gas reservoir. The results show that flow-rate deconvolution algorithms can greatly improve the fitting effect of the Blasingame production decline curve when applied to the analysis of unstable production of shale gas condensate reservoirs. Compared with the production decline analysis method in commercial software HIS Harmony RTA, the productivity prediction method based on a convolution equation of shale condensate gas reservoirs has better fitting affect and higher accuracy of recoverable reserves prediction. Compared with the actual production, the error of production predicted by the convolution equation is generally within 10%. This means it is a fast and accurate method. This study enriches the productivity prediction methods of shale condensate gas reservoirs and has important practical significance for the productivity prediction and stimulation optimization of shale condensate gas reservoirs. Full article

Research into condensate gas reservoirs in the oil and gas industry has been paid much attention and has great research value. There are also many deep condensate gas reservoirs, which is of great significance for exploitation. In this paper, the seepage performance of deep condensate gas reservoirs with natural fractures was studied. Considering that the composition of condensate gas changes during the production process, the component model was used to describe the condensate gas seepage in the fractured reservoir, modeled using the discrete fracture method, and the finite element method was used to conduct numerical simulation to analyze the seepage dynamic. The results show that the advancing speed of the moving pressure boundary can be reduced by 55% due to the existence of threshold pressure gradient. Due to the high-speed flow effect in the near wellbore area, as well as the high mobility of oil, the condensate oil saturation near the wellbore can be reduced by 42.8%. The existence of discrete natural fractures is conducive to improving the degree of formation utilization and producing condensate oil. Full article

Gas condensate reservoirs exhibit complex thermodynamic behaviors when the reservoir pressure is below the dew point pressure, leading to a condensate bank being created inside the reservoir, including gas and oil condensation. Due to natural fractures and multi-phase flows in fractured gas condensate reservoirs, there can be an erroneous interpretation of pressure-transient data using traditional multi-phase models or a fractured model alone. This paper establishes an analytical model for a well test analysis in a gas condensate reservoir with natural fractures. A three-region composite model was employed to characterize the multi-phase flow of retrograde condensation, and the fractured formation was described by a dual-porosity medium. In the first region, both the gas and condensate phases were mobile. In the second region, the gas was mobile whereas the condensates were immobile. In the third region, the only moving phase was the gas phase. The analytical solution was solved by a Laplace transformation to change the partial differential equations to ordinary differential equations. The Stehfest numerical inversion technique was then used to convert the solution of the proposed model into real space. Subsequently, the type curve was obtained and six flow regimes were determined. The influence of several factors on the pressure performance were studied by a sensitivity analysis. Finally, the accuracy of the model was verified by a case study. The model analysis results were in good agreement with the actual formation data. The proposed model provides a few insights toward the production behavior of fractured gas condensate reservoirs, and can be used to evaluate the productivity of such reservoirs. Full article