Search Results (217)

In this article, femtosecond laser scanning was used to create heterojunctions between silver nanowire (Ag NW) and graphene oxide (GO), resulting in a mechanical and electrical interconnection. Surface plasmon resonances (SPRs) were generated on the nanowire surface by using femtosecond laser irradiation, producing a periodically excited electric field along the Ag NWs. This electric field then interfered with the femtosecond laser field, creating strong localized heating effects, which melted the Ag NW and GO, leading to mechanical bonding between the two. The formation of these heterostructures was attributed to the transfer of plasmon energy from the Ag NW to the adjacent GO surface. Since the connection efficiency of the nanowires is closely related to the specific location and the polarization direction of the laser, FDTD simulations were conducted to model the electric field distribution on the surface of Ag NW and GO structures under different laser polarization directions, varying the lengths and diameters of the nanowires. Finally, the resistance changes of the printed Ag NW paths on the GO thin film after femtosecond laser irradiation were investigated. It was found that laser bonding could reduce the resistance of the Ag NW-GO heterostructures by two orders of magnitude, further confirming the formation of the junctions. Full article

This paper focuses on the switching and modulation techniques of terahertz waves, develops ${\mathrm{VO}}_2$ thin-film materials with an SPP structure, and uses terahertz time-domain spectroscopy (THz-TDS) to study the semiconductor–metal phase transition characteristics of ${\mathrm{VO}}_2$ thin films, especially the photoinduced semiconductor–metal phase transition characteristics of silicon-based ${\mathrm{VO}}_2$ thin films. The optical modulation characteristics of silicon-based ${\mathrm{VO}}_2$ thin films to terahertz waves under different light excitation modes, such as continuous light irradiation at different wavelengths and femtosecond pulsed laser irradiation, were analyzed. Combining the optical modulation characteristics of silicon-based ${\mathrm{VO}}_2$ thin films with the filtering characteristics of SPP structures, composite structures of ${\mathrm{VO}}_2$ thin films with metal hole arrays, composite structures of ${\mathrm{VO}}_2$ thin films with metal block arrays, and silicon-based ${\mathrm{VO}}_2$ microstructure arrays were designed. The characteristics of this dual-function device were tested experimentally. The experiment proves that the ${\mathrm{VO}}_2$ film material with an SPP structure has a transmission rate dropping sharply from 32% to 1% under light excitation; the resistivity changes by more than six orders of magnitude, and the modulation effect is remarkable. By applying the SPP structure to the ${\mathrm{VO}}_2$ material, the material can simultaneously possess modulation and filtering functions, enhancing its optical performance in the terahertz band. Full article

The incidence and mortality rates associated with melanoma are increasing. Due to their high proliferation rate, ability to self-renew, and resistance mechanisms, cancer cells often withstand conventional therapies such as radiation and chemotherapy. Therefore, further research is required to develop novel melanoma therapies with fewer adverse effects, but effective therapeutic impacts. This study aims to investigate how femtosecond laser treatment affects melanoma cells using the A375 cell line as an in vitro model. A375 melanoma cells were plated at a concentration of 10⁴ cells per well in 96-well plates and incubated overnight; then, they were subjected to femtosecond laser irradiation for durations of 3, 5, or 10 min, maintaining a steady power of 100 mW. The laser operated across different wavelengths in the ultraviolet, visible, and infrared ranges. Cell viability was evaluated 24 h after irradiation using the MTT assay. The results showed the significant inhibition of melanoma cell growth with various femtosecond laser parameters, particularly at 380 and 400 nm. At 380 nm, the cell viability was reduced by approximately 90%, and at 400 nm by 73%, after 10 min of exposure. Additional reductions were observed at 420 nm (47%) and 440 nm (18%), while no significant effects were found at 700–780 nm. The most effective exposure time was 10 min. Femtosecond laser radiation exerts a noteworthy anticancer effect on A375 cells, particularly at specific wavelengths and exposure durations, underscoring the potential of femtosecond laser therapy for treating melanoma. Exploring the underlying mechanisms of these effects and evaluating the clinical potential of this treatment modality requires further research. Full article

This study investigates near-infrared (NIR)-induced, Phyto-enhanced, second harmonic generation-mediated photodynamic therapy (Phyto-SHG-PDT) using barium titanate (BT)/rhein/polyethylene glycol 100 (PEG100) and BT/Yemenite “Etrog” leaf extract/PEG100 nanoconjugates. We compare continuous-wave (CW), multi-line Argon-ion laser illumination in the NIR range with high-peak-power femtosecond (fs) 800 nm pulses. Under CW NIR light, BT/rhein nanoconjugates reduced PC3 prostate cancer cell viability by 18% versus non-irradiated controls (p < 0.05), while BT/extract nanoconjugates exhibited 15% dark toxicity. The observed SHG signal matched theoretical predictions and previous CW laser studies. Reactive Oxygen Species (ROS) scavenger 1,3-diphenyl-isobenzofuran (DPBF) showed reduced absorbance at 410 nm upon NIR illumination, indirectly supporting SHG emission at 400 nm from nanoconjugates. Under fs-pulsed laser exposure, pronounced two-photon absorption (TPA) and SHG effects were observed in both nanoconjugate types. Our results demonstrate the effectiveness of BT/rhein nanoconjugates under both laser conditions, while the BT/extract nanoconjugates benefited from high-power pulsed excitation. These results highlight the potential of BT-based Phyto-SHG-PDT nanoconjugates for NIR and blue light applications, leveraging nonlinear optical effects for advanced photochemical cancer therapies. Full article

This review provides an overview of defects in silicon carbide (SiC) with potential applications as quantum qubits. It begins with a brief introduction to quantum qubits and existing qubit platforms, outlining the essential criteria a defect must meet to function as a viable qubit. The focus then shifts to the most promising defects in SiC, notably the silicon vacancy (V_Si) and divacancy (V_C-V_Si). A key challenge in utilizing these defects for quantum applications is their precise and controllable creation. Various fabrication techniques, including irradiation, ion implantation, femtosecond laser processing, and focused ion beam methods, have been explored to create these defects. Designed as a beginner-friendly resource, this review aims to support early-career experimental researchers entering the field of SiC-related quantum qubits. Providing an introduction to defect-based qubits in SiC offers valuable insights into fabrication strategies, recent progress, and the challenges that lie ahead. Full article

Proton beam therapy (PBT) is a rapidly advancing modality of hadron therapy. The primary advantage of proton therapy lies in a unique depth-dose distribution characterized by the Bragg peak, which enables a highly targeted irradiation of the area limited to the tumor, while minimizing the impact on healthy tissues. However, a broader clinical adoption of the ion beam therapy is limited by both economic and radiobiological constraints. One of the possible ways to increase the relative biological effectiveness (RBE) of proton therapy involves the use of radiosensitizers. Background/Objectives: In this work, we investigated the efficacy of using colloidal solutions of lanthanum hexaboride (LaB₆) nanoparticles (NPs) coated with polyacrylic acid (PAA) as sensitizers to increase the antitumor biological effectiveness of proton irradiation. This material has not yet been studied extensively so far, despite its promising physical and chemical properties and several reports on its biocompatibility. Methods: LaB₆ NPs were synthesized by femtosecond pulsed laser ablation, functionalized with PAA and characterized. The safety of NPs was evaluated in vitro using a Live/Dead assay on cell cultures: EMT6/P, BT-474, and in vivo in Balb/c mice after intravenous (i.v.) administration. The efficacy of binary proton therapy was evaluated in vitro on cell cultures: EMT6/P, BT-474, and in vivo in the model of human ductal carcinoma of the mammary gland BT-474 in female Nu/j mice after intratumoral (i.t.) administration at a dose of 2.0 mg/mouse and local proton irradiation (fractional exposure of 31 Gy + 15 Gy). The biodistribution of LaB₆-PAA NPs in the animal body was also evaluated. Results: Significant enhancement in cancer cell death following proton beam irradiation was demonstrated in vitro on EMT6/P, BT-474 cell lines. Although the antitumor efficacy observed in vivo was comparatively lower—likely due to the high sensitivity of the BT-474 xenografts—both proton monotherapy and binary treatment were well tolerated. Conclusions: LaB₆-PAA NPs show promise as efficient sensitizers capable of enhancing the biological efficacy of proton therapy, offering a potential path forward for improving therapeutic outcomes. Full article

We report on the formation of homogeneous nanostructures using a two-step ablation process with square flattop beams of femtosecond (fs) laser pulses. The Gaussian beam output from a ytterbium fs laser system was converted to a square flattop beam by a refractive beam shaper and a square mask. This beam was split into two with a diffraction optical element, and then the downsized beams were spatially and temporally superimposed on a titanium surface. In the first step, the interference fringes of these two beams formed grooves with a period of 1.9 µm through ablation. Next, the surface was irradiated at normal incidence by a single beam to form a homogeneous line-like nanostructure with a period of 490 nm in a 53 μm square area. This nanostructure had a constant period and was formed over 95% of the laser-processed area, indicating that the ratio between the nanostructure and modification area was over six times larger than that for a Gaussian beam. Full article

This study is focused on the fabrication and characterization of various dual waveguides through femtosecond (fs) laser irradiation of GeO₂-based glass samples. The objective of the present work is to develop diverse waveguide configurations, namely straight, S-bend and Y-shaped waveguides within GeO₂–PbO glasses embedded with silver nanoparticles, utilizing a double-guide platform, for photonic applications such as resonant rings and beam splitters. Enhanced guidance was observed with a larger radius of curvature (80 mm) among the two distinct S-bend waveguides produced. The maximum relative propagation loss was recorded for the S-bend waveguide with a 40 mm radius, while the minimum loss was noted for the Y-shaped waveguide. In the latter configuration, with an opening angle of 5° and a separation of 300 µm between the two arms, an output power ratio of 50.5/49.5 between the left and right arms indicated promising potential for beam splitter applications. During the study, the quality factor (M²) of the proposed architectures was measured and the 80 mm S-bend configuration presented the best symmetry between the x and y axes; in the case of the Y configuration the similarity between the M² values in both axes, for the first and second arms, indicates comparable light guidance. Full article

Fiber Bragg gratings (FBGs) inscribed by UV light and different femtosecond laser techniques (phase mask, point-by-point, and plane-by-plane) were exposed—in several irradiation cycles—to accumulated high doses of gamma rays (up to 124 MGy) and neutron fluence (8.7 × 10¹⁸/cm²) in a research-grade nuclear reactor. The FBG peak wavelengths were measured continuously in order to monitor radiation-induced shifts. Gratings inscribed on pure silica core fibers using near-IR femtosecond pulses through a phase mask showed the smallest shifts (<30 pm), indicating that these FBGs are suitable for temperature measurement even under extreme ionizing radiation. In contrast, the pointwise inscribed femtosecond gratings and a UV-inscribed grating showed maximal shifts of around 100 pm and 400 pm, respectively. Radiation-induced red shifts are believed to arise from gamma radiation damage, which may partially recover after irradiation is stopped. At the highest neutron exposures, grating peak blue shifts started to appear, apparently due to fiber compaction. Full article

The integration of a photodetector that converts optical signals into electrical signals is essential for scalable integrated lithium niobate photonics. Two-dimensional materials provide a potential high-efficiency on-chip detection capability. Here, we demonstrate an efficient on-chip photodetector based on a few layers of MoTe₂ on a thin film lithium niobate waveguide and integrate it with a microresonator operating in an optical telecommunication band. The lithium-niobate-on-insulator waveguides and micro-ring resonator are fabricated using the femtosecond laser photolithography-assisted chemical–mechanical etching method. The lithium niobate waveguide-integrated MoTe₂ presents an absorption coefficient of 72% and a transmission loss of 0.27 dB µm⁻¹ at 1550 nm. The on-chip photodetector exhibits a responsivity of 1 mA W⁻¹ at a bias voltage of 20 V, a low dark current of 1.6 nA, and a photo–dark current ratio of 10⁸ W⁻¹. Due to effective waveguide coupling and interaction with MoTe₂, the generated photocurrent is approximately 160 times higher than that of free-space light irradiation. Furthermore, we demonstrate a wavelength-selective photonic device by integrating the photodetector and micro-ring resonator with a quality factor of 10⁴ on the same chip, suggesting potential applications in the field of on-chip spectrometers and biosensors. Full article

In the realm of advanced optical fiber sensing (OFS) technologies, Fiber Bragg Grating (FBG) has garnered widespread application in the monitoring of temperature, strain, and external refractive indices, particularly within high-radiation environments such as high-energy physics laboratories, nuclear facilities, and space satellites. Notably, FBGs inscribed using femtosecond lasers are favored for their superior radiation resistance. Among various inscription techniques, the point-by-point (PbP) and line-by-line (LbL) methods are predominant; however, their comparative impacts on radiation durability have not been adequately explored. In this research, FBGs were inscribed on a single-mode fiber using both the PbP and LbL methods, and subsequently subjected to a total irradiation dose of 5.04 kGy (radiation flux of 2 rad/s) over 70 h in a ⁶⁰Co-γ radiation environment. By evaluating the changes in temperature- and strain-sensing performance of the FBG pre-irradiation and post-irradiation, this study identifies a more favorable technique for writing anti-irradiation FBG sensors. Moreover, an analysis into the radiation damage mechanisms in optical fibers, alongside the principles of femtosecond laser inscription, provides insights into the enhanced radiation resistance observed in femtosecond laser-written FBGs. This study thus furnishes significant guidance for the development of highly radiation-resistant FBG sensors, serving as a critical reference in the field of high-performance optical fiber sensing technologies. Full article

A detailed understanding of the physical essence of the interaction between a femtosecond laser and its target material remains an important and challenging goal. In this paper, the thermoelastic vibration behavior of nickel films irradiated by a femtosecond laser is studied by a molecular dynamics method combined with a two-temperature model. The model fully defines the spatial distribution of laser energy, the photoelectron coupling, and the electron-lattice coupling, and elucidates the temperature and stress evolution within the nickel film under femtosecond laser irradiation. Furthermore, the whole process and the mechanism of thermoelastic vibration is revealed at the atomic level. The thermoelastic vibration is divided into two stages, including continuous expansion during the process of energy relaxation and periodic expansion and contraction after reaching thermal equilibrium. The elastic oscillation of thin films is driven by periodic changes in energy, including the energy of atomic thermal motion and collective atomic motion. The effect of pulse fluence on thermoelastic vibration is also discussed in detail to provide reasonable suggestions for limiting this effect. This study provides the theoretical foundation and a feasible method for a deeper understanding of the interaction mechanisms between femtosecond lasers and materials. Full article

Laser-induced photothermal therapy using gold nanoparticles (AuNPs) has emerged as a promising approach to cancer therapy. However, optimizing various laser parameters is critical for enhancing the photothermal conversion efficacy of plasmonic nanomaterials. In this regard, the present study investigates the photothermal effects of dodecanethiol-stabilized hydrophobic ultrasmall spherical AuNPs (TEM size 2.2 ± 1.1 nm), induced by a 343 nm wavelength ultrafast femtosecond-pulse laser with a low intensity (0.1 W/cm²) for 5 and 10 min, on the cell morphology and viability of human hepatocellular carcinoma (HepG2) cells treated in vitro. The optical microscopy images showed considerable alteration in the overall morphology of the cells treated with AuNPs and irradiated with laser light. Infrared thermometer measurements showed that the temperature of the cell medium treated with AuNPs and exposed to the laser increased steadily from 22 °C to 46 °C and 48.5 °C after 5 and 10 min, respectively. The WST-1 assay results showed a significant reduction in cell viability, demonstrating a synergistic therapeutic effect of the femtosecond laser and AuNPs on HepG2 cells. The obtained results pave the way to design a less expensive, effective, and minimally invasive photothermal approach to treat cancers with reduced side effects. Full article

Transition metal dichalcogenides (TMDCs), particularly molybdenum disulfide (MoS₂), have gained significant attention in the field of optoelectronics and photonics due to their unique electronic and optical properties. The integration of TMDCs with plasmonic materials allows to tailor the optical response and offers significant advantages for photonic applications. This study presents a novel approach to synthesize MoS₂-Au nanocomposites utilizing femtosecond laser ablation in liquid to achieve tunable optical properties in the near-infrared (NIR) region. By adjusting ablation and fragmentation protocols, we successfully synthesize various core–shell and core–shell–satellite nanoparticle composites, such as MoS₂/MoS_xO_y, MoS_xO_y/Au, and MoS₂/MoS_xO_y/Au. UV-visible absorption spectroscopy unveils considerable changes in the optical response of the particles depending on the fabrication regime due to structural modifications. Hybrid nanoparticles exhibit enhanced photothermal properties when subjected to NIR-I laser irradiation, demonstrating potential benefits for selective photothermal therapy. Our findings underscore that the engineered nanocomposites not only facilitate green synthesis but also pave the way for tailored therapeutic applications, highlighting their role as promising candidates in the field of nanophotonics and cancer treatment. Full article

Graphene oxide-mediated photothermal therapy using femtosecond lasers has recently shown promise in treating hepatocellular carcinoma. However, significant work remains to optimize irradiation parameters for specific nanoparticle types and cancer cells to improve nanomaterial-mediated photothermal anticancer therapy. This study investigated the photothermal potential of nGO and nGO-PEG nanoparticles (NPs) combined with femtosecond laser irradiation at 515 nm and 1030 nm wavelengths, with varying power (0.1 and 0.2 W/cm²) and duration (5 and 10 min), to optimize photothermal therapy for hepatocellular carcinoma. Conversion efficiency of NPs, morphology and viability of HepG2 and normal MDCK cells after treatments were evaluated using an electronic thermometer, phase-contrast microscopy, and WST-1 assay. The results revealed that nGO-PEG NPs exhibited better photothermal efficiency than nGO, with 515 nm of irradiation inducing a temperature increase up to 19.1 °C compared to 4.7 °C with 1030 nm of light. Laser exposure to 515 nm significantly reduced HepG2 cell viability, with the most intense conditions (10 min at 0.2 W/cm²) causing a decrease of up to 58.2% with nGO and 43.51% with nGO-PEG. Normal MDCK cells showed minimal impact or a slight viability increase, especially with nGO-PEG. Combined treatment with laser irradiation and NPs induced significant morphological changes in HepG2 cells, including cell detachment and apoptotic-like characteristics, particularly with 1030 nm of irradiation. MDCK cells exhibited minimal morphological changes, with some recovery observed under lower energy conditions. These findings suggest that low-energy lasers and engineered nanomaterials could provide a minimally invasive approach to photothermal cancer therapy with reduced side effects. Full article