Search Results (6)

This paper presents the first hybrid supply modulator (HSM) designed for envelope tracking power amplifiers (ET-PAs) in base station applications. The focus is on a rail-to-rail Class-AB linear amplifier (LA) optimized for high-voltage and wide-bandwidth operation. The LA is designed using 130 nm BCD technology, utilizing Laterally Diffused Metal-Oxide Semiconductor (LDMOS) transistors for high-voltage operation and incorporating shielding MOSFETs to protect the low-voltage devices. The circuit utilizes dual power supply domains (5 V and 30 V) to improve power efficiency. The proposed LA achieves a bandwidth of 100 MHz and a slew rate of +1003/−852 V/$\mathsf{\mu }\mathrm{s}$, with a quiescent power consumption of 0.89 W. Transient simulations using a 50 MHz bandwidth 5G NR envelope input demonstrate that the proposed HSM achieves a power efficiency of 83%. Consequently, the proposed HSM supports high-output (100 W) wideband 5G NR transmission with enhanced efficiency. Full article

This paper presents a highly efficient 5G New-Radio (NR) RF power amplifier module (PAM). The n77 PAM consists of a high-voltage differential-topology 2 μm GaAs HBT power amplifier, a CMOS controller, a silicon-on-insulator (SOI) switch, an integrated passive device (IPD) bandpass filter, a low-noise amplifier (LNA), and a bi-directional coupler. This PAM generates a saturation output power of 32.7 dBm including the loss of the SOI switch and output filter. The designed n77 PAM is tested with a commercial envelope tracker IC (ET-IC). The designed PAM with an ET-IC achieves an ACLR of −37 dBc at a 27 dBm output power with a DFT-s-OFDM QPSK 100 MHz NR signal and saves a dc power consumption of 950 mW compared to the APT mode. For the CP-OFDM 256QAM with the most stringent EVM requirements, it achieves an EVM of 1.22% at 23 dBm and saves 640 mW compared to the APT mode. Full article

This paper presents an envelope linearization technique to compensate for the nonlinear distortion of envelope tracking (ET) power amplifiers (PAs) for 5G new radio (NR) mobile terminals. The proposed envelope optimization (EOPT) method is agnostic of the nonlinear distortion generated in the envelope supply path and can compensate for the nonlinear distortion at the ET PA output without the need to monitor the output at the envelope tracking modulator (ETM). The linearization system in the envelope path is based on the envelope generalized memory polynomial (EGMP) behavioral model. Since the ETM output is not available, an iterative nonlinear least squares solution inspired in the deep deterministic policy gradient (DDPG) algorithm is proposed to extract the coefficients of the EGMP model. The EOPT method is validated on a system-on-chip (SoC) ET PA board designed for mobile terminal applications. Experimental results show the suitability of the proposed method to guarantee the linearity requirements (i.e., adjacent channel power ratio below −36 dBc) with 16.8% of power efficiency when operating the ET PA with 5G new radio test signals of 60 MHz bandwidth operating at 2.55 GHz (band 7). The linearization performance of the proposed EOPT method is comparable to the envelope leakage cancellation (ELC) approach (but saving the need for an analog to digital converter to monitor the ETM output), and can outperform a conventional I-Q digital predistorter based on the generalized memory polynomial (GMP) behavioral model. Full article

It is well known that modern wireless communications systems need linear, wide bandwidth, efficient Radio Frequency Power Amplifiers (RFPAs). However, conventional configurations of RFPAs based on Class A, Class B, and Class AB exhibit extremely low efficiencies when they manage signals with a high Peak-to-Average Power Ratio (PAPR). Traditionally, a number of techniques have been proposed either to achieve linearity in the case of efficient Switching-Mode RFPAs or to improve the efficiency of linear RFPAs. There are two categories in the application of aforementioned techniques. First, techniques based on the use of Switching-Mode DC–DC converters with a very-fast-output response (faster than 1 µs). Second, techniques based on the interaction of several RFPAs. The current expansion of these techniques is mainly due to their application in cellphone networks, but they can also be applied in other promising wireless communications systems such as Visible Light Communication (VLC). The main contribution of this paper is to show how Envelope Tracking (ET), Envelope and Elimination (EER), Outphasing, and Doherty techniques can be helpful in developing more efficient VLC transmitters capable of reaching high bit-rates (higher than 1 Mbps) by using advance modulation schemes. Finally, two examples based on the application of the Outphasing technique and the use of a Linear-Assisted Envelope Amplifier (EA) to VLC are presented and experimentally verified. Full article

A ruggedness improved multi-band radio frequency (RF) power amplifier (PA) module applicable to mobile handsets, which are required to survive against a serious load impedance change under extreme power and bias conditions, is presented. In this method, the load impedance of PA is adaptively adjusted with a digitally controlled impedance corrector to keep the PA safe by performing a load mismatch detection. The impedance mismatch detector, impedance corrector, and other RF switches were all integrated into a single integrated circuit (IC) using silicon on insulator (SOI) complementary metal oxide semiconductor (CMOS). For the verification purpose, a 2-stage hetero junction bipolar transistor (HBT) PA module adopting this method was fabricated. At a frequency of 1915 MHz, a collector bias voltage of 4.2 V, and over a wider range of load impedance variation between a VSWR of 1 and a VSWR of 5.5, it did not fail. When this technique was not applied with a voltage standing wave ratio (VSWR) range of 1 to 4, it resulted in an acceptable RF performance degradation of 1% power added efficiency (PAE) in envelope tracking (ET) mode. Moreover, it survived at a bias voltage 1V larger than when the technique was not applied for the same mismatch condition. Full article

An analytical method to design a power amplifier (PA) with an optimized power added efficiency (PAE) trajectory for envelope tracking (ET) architecture is proposed. To obtain feasible matching solutions for high-efficiency performance of the PA in the dynamic supply operation, hybrid continuous modes (HCM) architecture is introduced. The design space for load impedances of the HCM PAs with nonlinear capacitance is deduced mathematically using the device’s embedding transfer network, without the necessity of using load-pull. The proposed design strategy is verified with the implementation of a GaN PA operating over the frequency range of 1.9 GHz to 2.2 GHz with PAE between 67.8% and 72.4% in the 6.7 dB back-off power region of the ET mode. The ET experimental system was set up to evaluate the application of the PA circuit. Measurement results show that the ET PA at 2.1 GHz reaches the efficiency of 61%, 54%, 44% and an error vector magnitude (EVM) of 0.32%, 0.60%, 0.67% at an average output power of 34.4 dBm, 34.2 dBm, 34.1 dBm for 6.7 dB peak-to-average power ratios (PAPR) signals with 5 MHz, 10 MHz, and 20 MHz bandwidths, respectively. Additionally, tested by a 20 MHz bandwidth 16 quadrature amplitude modulation (QAM) signal, 41.8% to 49.2% efficiency of ET PA is achieved at an average output power of 33.5 dBm to 35.1 dBm from 1.9 GHz to 2.2 GHz. Full article