Search Results (948)

The use of microwaves (MWs) has been proposed as an energy-efficient method for reducing checking. Along with understanding moisture distribution, it is essential to consider structural characteristics to explain how MWs reduce checking. The influence of MWs on these characteristics depends on the food matrix’s dielectric and viscoelastic properties, which vary significantly between fresh and pre-baked dough. This study investigates the effects of MW treatment applied before (MW-O) or after conventional oven baking (O-MW) on low-fat biscuits that are prone to checking. Color (CIELab), thickness, moisture content and distribution, checking rate, texture, sensory properties, energy consumption and baking time were analyzed. The findings suggest that MWs reduce checking rate by eliminating internal moisture differences, while also changing structural properties, as evidenced by increased thickness and hardness. MW-O eliminated checking (control samples showed 100%) but negatively affected color, texture (increased hardness and breaking work), and sensory quality. The O-MW checking rate (3.41%) was slightly higher than in MW-O, probably due to the resulting different structural properties (less thickness, less hardness and breaking work). O-MW biscuits were the most preferred by consumers (54.76% ranked them first), with color and texture close to the control samples. MW-O reduced total energy consumption by 16.39% and baking time by 25.00%. For producers, these improvements could compensate for the lower biscuit quality. O-MW did not affect energy consumption but reduced baking time by 14.38%. The productivity improvement, along with the reduction in checking and the satisfactory sensory quality, indicates that O-MW could be beneficial for the bakery sector. Full article

Hexagonal boron nitride (hBN) is a layered material with a wide variety of excellent properties for emergent applications in quantum photonics using atomically thin materials. For example, it hosts single-photon emitters that operate up to room-temperature, it can be exploited for atomically flat tunnel barriers, and it can be used to form high finesse photonic nanocavities. Moreover, it is an ideal encapsulating dielectric for two-dimensional (2D) materials and heterostructures, with highly beneficial effects on their electronic and optical properties. Depending on the use case, the thickness of hBN is a critical parameter and needs to be carefully controlled from the monolayer to hundreds of layers. This calls for quick and non-invasive methods to unambiguously identify the thickness of exfoliated flakes. Here, we show that the apparent color of hBN flakes on different SiO₂/Si substrates can be made to be highly indicative of the flake thickness, providing a simple method to infer the hBN thickness. Using experimental determination of the colour of hBN flakes and calculating the optical contrast, we derived the optimal substrates for the most reliable hBN thickness identification for flakes with thickness ranging from a few layers towards bulk-like hBN. Our results offer a practical guide for the determination of hBN flake thickness for widespread applications using 2D materials and heterostructures. Full article

In classic all-dielectric one-dimensional photonic crystals, transparent bands exhibit strong angular dispersion. Herein, we realize an angle-dispersion-free near-infrared transparent band in a one-dimensional photonic hypercrystal containing hyperbola-dispersion metamaterials. As the incident angle increases from 0° to 80°, the relative shifts of the wavelengths of four transmittance peaks within the transparent band are smaller than 1.5% and the bandwidth of the transparent band marginally fluctuates from 1098.2 to 1132.5 nm. Particularly, the angle-dispersion-free property of the transparent band is quite robust with respect to the layer thickness disturbance. Our work not only offers a viable method of achieving angle-dispersion-free transparent bands but also facilitates the development of transparency-based optical devices. Full article

To meet the requirements for radar echo acquisition and feature extraction from stratified media and rough-surfaced targets, a vehicle was geometrically modelled in CAD. Monte Carlo techniques were applied to generate the rough interfaces at air–snow and snow–soil boundaries and over the vehicle surface. Soil complex permittivity was characterized with a four-component mixture model, while snow permittivity was described using a mixed-media dielectric model. The composite electromagnetic scattering from a rough-surfaced vehicle on snow-covered soil was then analyzed with the finite-difference time-domain (FDTD) method. Parametric studies examined how incident angle and frequency, vehicle orientation, vehicle surface root mean square (RMS) height, snow liquid water content and depth, and soil moisture influence the composite scattering coefficient. Results indicate that the coefficient oscillates with scattering angle, producing specular reflection lobes; it increases monotonically with larger incident angles, higher frequencies, greater vehicle RMS roughness, and higher snow liquid water content. By contrast, its dependence on snow thickness, vehicle orientation, and soil moisture is complex and shows no clear trend. Full article

This paper presents the design and performance analysis of a compact wireless power transfer (WPT) system operating at 1.6 GHz. The transmitter (Tx) structure consists of a circular slot and a circular radiating element, excited from the backside of the substrate, while the receiver (Rx) comprises a slotted patch antenna miniaturized using two vertical vias. The initial power transfer efficiency (PTE), represented by the transmission coefficient $S_{21}$, was measured to be −31 dB with a 25 mm separation between Tx and Rx. To enhance the efficiency of the system, a dielectric matching media (MM) was introduced between the transmitter and receiver. Through the implementation of the MM, the PTE improved significantly, with $S_{21}$ increasing to −24 dB. A parametric study was conducted by varying the thickness of the MM from 1 mm to 10 mm and the relative permittivity (${\epsilon }_r$) from 5 to 30. The results demonstrate that both the thickness and dielectric constant of the MM play a crucial role in improving the coupling and overall efficiency of the WPT system. The optimal configuration was achieved with a matching media thickness of 10 mm and a relative permittivity of 25, which yielded the best improvement in transmission performance. This work offers a practical approach to enhance near-field WPT efficiency using simple matching structures and is particularly relevant for compact and low-profile energy transfer applications. Full article

Since the definitions of the two-dimensional (2D) optical absorption coefficient and photoconductivity are independent of the thickness of 2D materials, they are more suitable than the dielectric function to describe the optical properties of 2D materials. Based on the many-body GW method and the Bethe–Salpeter equation, we calculated the quasiparticle electronic structure, optical absorbance, and complex photoconductivity of 2D InSe from a single layer (1L) to three layers (3L). The calculation results show that the energy difference between the direct and indirect band gaps in 1L, 2L, and 3L InSe is so small that strain can readily tune its electronic structure. The 2D optical absorbance results calculated taking into account exciton effects show that light absorption increases rapidly near the band gap. Strain modulation of 1L InSe shows that it transforms from an indirect bandgap semiconductor to a direct bandgap semiconductor in the biaxial compressive strain range of −1.66 to −3.60%. The biaxial compressive strain causes a slight blueshift in the energy positions of the first and second absorption peaks in monolayer InSe while inducing a measurable redshift in the energy positions of the third and fourth absorption peaks. Full article

We present a simple method for customizing the optical characteristics of gold-core, silver-shell (Au@Ag) nanoparticles through controlled morphosynthesis via a seed-mediated chemical reduction approach. By systematically adjusting the concentration of cetyltrimethylammonium chloride (CTAC), we obtained precise control over both the thickness of the Ag shell and the particle shape, transitioning from spherical nanoparticles to distinctly defined nanocubes. Bright field and high-angle annular dark-field scanning transmission electron microscopy (BF-STEM and HAADF-STEM), and energy-dispersive X-ray spectroscopy (EDS) were employed to validate the structural and compositional changes. To link morphology with optical behavior, we utilized the Mie and Maxwell–Garnett theoretical models to simulate the dielectric response of the core–shell nanostructures, showing trends that align with experimental UV-visible absorption spectra. This research presents an easy and adjustable method for modifying the plasmonic properties of Ag@Au nanoparticles by varying their shape and shell, offering opportunities for advanced applications in sensing, photonics, and nanophotonics. Full article

In the Internet of Things (IoT) era, the demand for cost-effective, flexible, wearable antennas and circuits has been growing. Accordingly, screen-printing techniques are becoming more popular due to their lower costs and high-volume manufacturing. This paper presents and investigates a full-screen-printed 1 × 4 Quasi-Yagi-Uda antenna array on a high-transparency flexible Zeonor thin-film substrate for emerging 26 GHz band (24.25–27.55 GHz) 5G applications. As part of this study, screen-printing implementation rules are developed by properly managing ink layer thickness on a transparent flexible Zeonor thin-film dielectric to achieve a decent antenna array performance. In addition, a screen-printing repeatability study has been carried out through a performance comparison of 24 antenna array samples manufactured by our research partner from CEA-Liten Grenoble. Despite the challenging antenna array screen printing at higher frequencies, the measured results show a good antenna performance as anticipated from the traditional subtractive printed circuit board (PCB) manufacturing process using standard substrates. It shows a wide-band matched input impedance from 22–28 GHz (i.e., 23% of relative band-width) and a maximum realized gain of 12.8 dB at 27 GHz. Full article

Palladium (Pd) and titanium (Ti) exhibit opposite dielectric responses upon hydrogenation, with stronger effects observed in the near-infrared (NIR) region. Leveraging this contrast, we investigated Ti/Pd bilayer thin films as a platform for NIR hydrogen sensing—particularly at telecommunication-relevant wavelengths, where such devices have remained largely unexplored. Ti/Pd bilayers coated with Teflon AF (TAF) and fabricated via sequential electron-beam and thermal evaporation were characterized using optical transmission measurements under repeated hydrogenation cycles. The Ti (5 nm)/Pd (x = 2.5 nm)/TAF (30 nm) architecture showed a 2.7-fold enhancement in the hydrogen-induced optical contrast at 1550 nm compared to Pd/TAF reference films, attributed to the hydrogen ion exchange between the Ti and Pd layers. The optimized structure, with a Pd thickness of x = 1.9 nm, exhibited hysteresis-free sensing behavior, a rapid response time (${\mathrm{t}}_{90}$ < 0.35 s at 4% ${\mathrm{H}}_2$), and a detection limit below 10 ppm. It also demonstrated excellent selectivity with negligible cross-sensitivity to $\mathrm{C}{\mathrm{O}}_2$, $\mathrm{C}{\mathrm{H}}_4$, and CO, as well as high durability, showing less than 6% signal degradation over 135 hydrogenation cycles. These findings establish a scalable, room-temperature NIR hydrogen sensing platform with strong potential for deployment in automotive, environmental, and industrial applications. Full article

Linear passive electrical devices/components are usually characterized in the frequency domain by their impedance, i.e., the ratio of the voltage and current phasors. The use of the impedance concept does not raise particular concerns in low-frequency regimes; however, things become more complicated when it comes to rapid time-varying phenomena, mainly because the voltage depends not only on the position of the points between which it is defined but also on the choice of the integration path that connects them. In this article, based on first principles (Maxwell equations and Poynting vector flow considerations), we discuss the concept of impedance and define it unequivocally for a class of electrical devices/components with rotational symmetry. Two application examples are presented and discussed. One simple example concerns the per-unit-length impedance of a homogeneous cylindrical wire subject to the skin effect. The other, which is more elaborate, concerns a heterogeneous structure that consists of a dielectric disk sandwiched between two metal plates. For the lossless situation, the high-frequency impedance of this device (circular parallel plate capacitor) reaches zero when the frequency reaches a certain critical frequency f_c; then, it becomes inductive and increases enormously when the frequency reaches another critical frequency at 1.6 f_c. The influence of losses on the impedance of the device is thoroughly investigated and evaluated. Impedance corrections due to dielectric losses are analyzed using a frequency-dependent Debye permittivity model. The impedance corrections due to plate losses are analyzed by considering radial current distributions on the outer and inner surfaces of the plates, the latter exhibiting significant variations near the critical frequencies of the device. Full article

Thermosensitive Poly(N-isopropylacrylamide) (PNIPAm) films were synthesized via atmospheric pressure dielectric barrier discharge (APDBD) plasma polymerization. In order to control the thickness of the films, a spin coating technique was used during the deposition of N-isopropylacrylamide (NIPAM) monomer solution onto several glass substrates. We used the coefficient of determination (R-square value) in linear regression to investigate the significance and optimize spin coating parameters during the fabrication of NIPAM coatings before exposure to APDBD plasma to ensure reproducible and uniform film properties. The spin coating parameters investigated in this study include spin speed, spin time, and NIPAM solution concentration with R-square values of 0.978, 0.946, and 0.944, respectively. Also, as a result of the thermosensitive nature of NIPAM, the spin coating operating conditions of temperature and humidity were maintained at 39.0 °C and 15%, respectively. During the APDBD plasma polymerization, argon was used as the discharge gas, and the distance between the two parallel electrodes and plasma frequency were maintained at 5.0 mm and 17 kHz, respectively. The plasma exposure time required for polymerization of PNIPAm coatings was optimized to 60 s. Also, the results showed that a coating with minimal defects had an optimal thickness of 5.18 μm, fabricated under conditions of 90 wt.% NIPAM concentration, spin speed of 4000 rpm, and total spin time of 7 s. Full article

In this work, we propose and analyze a thermally tunable metasurface based on indium antimonide (InSb), designed to operate in the terahertz (THz) frequency range. The metasurface exhibits dual functionalities: single-band perfect absorption and efficient polarization conversion, enabled by the temperature-dependent permittivity of InSb. At approximately 280 K, InSb transitions into a metallic state, enabling the metasurface to achieve near-unity absorptance (100%) at 0.408 THz under normal incidence, independent of polarization. Conversely, when InSb behaves as a dielectric at 200 K, the metasurface operates as an efficient polarization converter. By exploiting structural anisotropy, it achieves a polarization conversion ratio exceeding 85% over the frequency range from 0.56 to 0.93 THz, while maintaining stable performance for incident angles up to 45°. Parametric analyses show that the resonance frequency and absorption intensity can be effectively tuned by varying the InSb square size and the silica (SiO₂) layer thickness, achieving maximum absorptance at a SiO₂ thickness of 16 μm. The proposed tunable metasurface offers significant potential for applications in THz sensing, imaging, filtering, and wavefront engineering. Full article

BaTiO₃-based lead-free ferroelectric films with a large recoverable energy density (W_rec) and a high energy efficiency (η) are crucial components for next-generation dielectric capacitors, which are used in energy conditioning and storage applications in integrated circuits. In this study, grain-engineered (Ba_0.95,Sr_0.05)(Zr_0.2,Ti_0.8)O₃ (BSZT) ferroelectric thick films (~500 nm) were prepared on Si substrates. These films were deposited at 350 °C, 100 °C lower than the temperature at which the LaNiO₃ buffer layer was deposited on Pt/Ti. This method reduced the (001) grain population due to a weakened interface growth mode, while promoting volume growth modes that produced (110) and (111) grains with a high polarizability. As a result, these films exhibited a maximum polarization of ~88.0 μC/cm², a large W_rec of ~203.7 J/cm³, and a high energy efficiency η of 81.2% (@ 6.4 MV/cm). The small-field dielectric constant nearly tripled as compared with that of the same BSZT/LaNiO₃ heterostructure deposited at the same temperature (350 °C or 450 °C). The enhanced linear dielectric response, delayed ferroelectric polarization saturation, and increased dielectric strength due to the nano-grain size, collectively contributed to the improved energy storage performance. This work provides a novel approach for fabricating high-performance dielectric capacitors for energy storage applications. Full article

This paper presents a compact monopole wideband antenna based on DGS. The ultimate geometry of the designed antenna is obtained after many design modifications and optimizations. A commercially available Taconic TLY substrate with a dielectric constant (ε_r) = 2.2, loss tangent (tan δ) = 0.0009, and thickness (h) of 1.524 mm is used. The dimension of the substrate is 34 mm × 28 mm. A 50Ω microstrip transmission line of size 12 mm × 3 mm is used to feed the antenna. Simulation results demonstrate a bandwidth from 4.08 to 18.92 GHz, a percentage bandwidth of 129% for S11 < −10 dB, and a peak gain of 7.4 dB. The DGS slots are embedded into the ground plane to enhance the antenna’s bandwidth, impedance matching, gain, and efficiency. For verification, the proposed antenna is fabricated and measured. Good agreement between measured and simulated results is observed. Thus, this antenna is appropriate for various modern wireless communication systems. Full article

Utilizing biomass resources to develop carbon-based microwave-absorbing materials adheres to the principles of sustainable development. Nevertheless, the single loss mechanism of pure carbon materials is limited. Additionally, the carbonization of artificially synthesized polymers has poor environmental performance and involves complex processes. These issues restrict their performance and broader applicability. In this study, cobalt-doped seaweed sludge porous carbon (Co/SSPC) with different cobalt contents was synthesized via a simple grinding–carbonization treatment. The addition of cobalt can regulate the graphitization degree of porous carbon, achieving a suitable amorphous-to-crystalline carbon ratio of 2.05. This not only enhances magnetic loss but also modifies dielectric loss and optimizes impedance matching. The construction of synergistic magnetic and dielectric loss mechanisms enables Co/SSPC to exhibit excellent microwave absorption performance. Specifically, Co/SSPC achieved a minimum reflection loss (RL_min) of −66.91 dB at a thickness of 4.79 mm and an effective absorption bandwidth (EAB) of 5.09 GHz at a thickness of 1.6 mm. This study provides a practical approach for the functional application of natural polymer waste algal sludge and highlights its potential in the low-cost production of microwave absorbing materials. Full article