Search Results (226)

This paper presents a carbon monoxide (CO) detection mechanism achieved through further improvement of the sensing antenna based on hybrid spoof localized surface plasmons (SLSPs) and cavity resonance. Unlike conventional approaches relying on chemical reactions or photoelectric effects, the all-metal configuration detects dielectric variations through microwave-regime resonance frequency shifts, enabling CO/air differentiation with theoretically enhanced robustness and environmental adaptability. The designed system achieves measured figures of merit (FoMs) of 183.2 RIU⁻¹, resolving gases with dielectric contrast below 0.1%. Experimental validation successfully discriminated CO (ε_r = 1.00262) from air (ε_r = 1.00054) under standard atmospheric pressure at 18 °C. Full article

Hydrogen is gaining prominence as a clean energy vector, yet its extreme flammability demands robust detection solutions for industrial safety. In this study, we present the development and experimental validation of a microwave hydrogen gas sensor based on a patch-type microstrip antenna with a silver sensing element. The device operates at 5.99 GHz and was tested under controlled environmental conditions (humidity: 20 ± 0.4%, temperature: 27 ± 0.2 °C). Hydrogen exposure induces measurable shifts in the antenna’s resonant frequency due to dielectric modulation of the silver layer. The sensor exhibited a linear sensitivity of 3 kHz/ppm in the 310–600 ppm concentration range, with a residual standard deviation of 31.1 kHz and a calculated limit of detection (LOD) of approximately 31 ppm. The reflection coefficient remained below −10 dB throughout, confirming that the antenna maintains functional RF performance during sensing. These results demonstrate the sensor’s dual functionality for gas detection and communication, offering a compact and scalable platform for hydrogen safety monitoring. Full article

Ca₃(BO₃)₂ microwave dielectric ceramics with space group R-3c (#167) were prepared by cold sintering, and their properties were systematically investigated. Phonon density of state diagrams for the Ca₃(BO₃)₂ lattice were obtained based on first-principles calculations to provide a more comprehensive understanding of the lattice vibrational properties of the material. Raman scattering and infrared reflectance spectroscopy were employed to investigate the lattice vibrational characteristics, identifying two types of vibrational modes: internal modes associated with the planar bending and symmetric stretching vibrations of the [BO₃] group, and external modes linked to the vibrations of the [CaO₆] octahedron. The intrinsic dielectric properties were determined by fitting the experimental data using a four-parameter semi-quantum model. The results demonstrate that the dielectric properties of Ca₃(BO₃)₂ ceramics are primarily influenced by the external vibrational modes. The sample under 800 MPa exhibits optimal dielectric performance, with a dielectric constant (ε_r) of 5.95, a quality factor (Q × f) of 11,836 GHz, and a temperature coefficient of resonant frequency (τ_f) of −39.89 ppm/°C. A simulation of this Ca₃(BO₃)₂ sample as a dielectric substrate was conducted using HFSS to fabricate a microstrip patch antenna operating at 14.97 GHz, which exhibits a return loss (S₁₁) of −25.5 dB and a gain of 7.15 dBi. Full article

Resonators are passive components that respond to an excitation signal by oscillating at their natural frequency with an exponentially decreasing amplitude. When combined with antennas, resonators enable purely passive chipless sensors that can be read wirelessly. In this contribution, we investigate the properties of dielectric resonators, which combine the following functionalities: They store the readout signal for a sufficiently long time and couple to free space electromagnetic waves to act as antennas. Their mode spectrum, along with their resonant frequencies, quality factor, and coupling to electromagnetic waves, is investigated using a commercial finite element program. The fundamental mode exhibits a too-low overall Q factor. However, some higher modes feature overall Q factors of several thousand, which allows them to act as transponders operating without integrated circuits, batteries, or antennas. To experimentally verify the simulations, isolated dielectric resonators exhibiting modes with similarly high radiation-induced and dissipative quality factors were placed on a low-loss, low permittivity ceramic holder, allowing their far-field radiation properties to be measured. The radiation patterns investigated in the laboratory and outdoors agree well with the simulations. The resulting radiation patterns show a directivity of approximately 7.5 dBi at 2.5 GHz. The sensor was then heated in a ceramic furnace with the readout antenna located outside at room temperature. Wireless temperature measurements up to 700 °C with a resolution of 0.5 °C from a distance of 1 m demonstrated the performance of dielectric resonators for practical applications. Full article

Traditional Beidou Navigation Satellite System anti-jamming array antennas mostly use PCB plates, but in extreme vibration environments, their rigidity may cause the antenna structure to be more susceptible to damage. Especially in an extremely high-temperature environment, it may cause thermal expansion, softening, and even melting of metal materials, which will affect the structure and performance of the antenna; In this paper, a Beidou array antenna integrating high seismic resistance, high-temperature stability, and anti-interference ability is designed and studied. The structural parts of the antenna are composed of 7075 aluminum alloy and high-temperature ceramic material technology, which has a compact structure and strong corrosion resistance, which is especially suitable for aviation and marine environments. The antenna works stably at 400 °C and has excellent heat resistance. Built-in shock-absorbing elements or shock-absorbing materials are used to effectively absorb and disperse vibration energy and reduce the direct impact on the internal components of the antenna. Considering the anti-interference performance caused by the size of the array spacing and the mutual coupling between the array elements, the array spacing is designed to be between λ/4 and λ/2. In simulations and experiments, the designed antenna array shows good performance and proves its applicability for high-temperature applications. The antenna frequency includes the B3 band (1250.618~1286.423 MHz) and B1 band (1559.052~1591.788 MHz) of the Beidou Navigation Satellite System. The following article includes the introduction, proposed array antenna structure and dimension, antenna simulation results, antenna protype and environment test, conclusions and future work. Full article

This paper investigates the usefulness of combining dielectric and conductive materials with various geometries to build resonators and enhance patch antenna performance when considering the decoupled design approach. Three materials (distilled water, glycerin, and graphite) and fifteen geometries are considered. The obtained results through numerical simulations show how the selected materials and geometries can be combined to strategically design resonators that can effectively confine electromagnetic fields, shift the resonant frequency, improve antenna directionality and effective gain, facilitate multi-band operation, broaden the bandwidth, and improve impedance matching and the radiation pattern. Overall, the analyses and discussions offer insights and guidelines for combining dielectric and conductive materials with several geometries to build a resonator that can improve patch antenna performance when a low-quality substrate is considered. Full article

A wideband dual-polarized dielectric resonator antenna (DRA) with gain-filtering response was proposed in this paper. First, a differentially fed, low-profile crossed-DRA was used to obtain orthogonal polarizations with two resonant modes. A radiation null at upper band edge was also generalized. Second, with the introduction of four parasitic patches at the top of the crossed DRA, another resonant mode at lower band was excited, and the bandwidth was greatly expanded. Moreover, the introduction of parasitic patches could also help improve the selectivity of realized gain with another radiation null at the upper band edge. Furthermore, four sequentially rotated shorting coupling structures (SRSCSs) were proposed for the first time to generalize two additional radiation nulls. Finally, a wideband bandpass filtering response of the realized gain with four radiation nulls was obtained. Prototypes of the proposed antennas were fabricated, and the testing results showed that the antenna had a wide operation band of 57.1% from 2.75 GHz to 4.95 GHz with sharp roll-off at the band edge. This technique could also be used in wireless communication devices at millimeter/optical front ends and other multi-wavelength fiber lasers with micro structures. Full article

This paper introduces a flexible loop antenna-based sensor optimized for real-time monitoring of meat quality by detecting changes in dielectric properties over a six-day storage period. Operating within the 2.4 GHz ISM band, the sensor is designed using CST Microwave Studio 2024 to deliver high sensitivity and accuracy. The sensing mechanism leverages resonance frequency shifts caused by variations in permittivity as the meat degrades. Experimental validation across five samples showed a consistent frequency shift from 2.14 GHz (Day 0) to 1.29 GHz (Day 5), with an average sensitivity of $0.173\mathrm{GHz}/\mathrm{day}$. A strong correlation was observed between measured and simulated results, as evidenced by linear regression ($R^2=0.984$ and $R^2=0.974$ for measured and simulated data, respectively). The sensor demonstrated high precision and repeatability, validated by low standard deviations and minimal frequency deviations. Compact, printable, and cost-effective, the proposed sensor offers a scalable solution for food quality monitoring. Its robust performance highlights its potential for integration into IoT platforms and extension to other perishable food products, advancing real-time, non-invasive, RF-based food safety technologies. Full article

This paper presents a novel dual-band antenna design for simultaneous 5G communication and localization services in high-speed train (HST) scenarios. It operates in the frequency range 1 (FR1) n78 band at 3.5 GHz and the FR2 n258 band at 26.2 GHz. The design combines a dielectric resonator antenna (DRA) and a planar patch antenna to achieve dual-band functionality. This provides efficient performance across both mid-band and millimeter-wave frequencies for advanced 5G applications. The dual-band configuration is motivated by the need to balance wide coverage and high data rates within a single, compact antenna design, addressing the specific challenges of maintaining stable connectivity and efficient spectrum utilization in high-speed, data-intensive environments. A common challenge in dual-band antenna designs is the interference between low- and high-frequency antennas, which can significantly degrade performance or even cause antenna failure. Our design addresses this issue by minimizing interference between the patch and DRA elements, ensuring stable operation across both frequency bands. As a result, the antenna achieves impressive gains and bandwidth, with a maximum gain of 6.8 dBi and an impedance bandwidth of 22.5% for the dual-band configuration. Also, both radiators present high total efficiency above 90%. The compact size of the antenna makes it highly suitable to be mounted on the roof of the train to enable 5G communication and location-based services for both safety-critical and liability-critical applications in HST scenarios. Full article

This article presents a new design for a dual-band circular polarization microstrip patch antenna that can be used in unmanned aerial vehicle (UAV) applications. The proposed antenna consists of an etched circular shape on the radiator side of the antenna with multiple slots and stubs. The bottom side comprises a partial ground plane with multiple horizonal, vertical and square slots. These shapes on the front and bottom sides of the antenna are used to keep the resonant frequencies, impedance bandwidth and axial ratio (AR) at the desired values. The antenna operation is within the WiFi frequency bands, achieving maximum gains of 5.01 and 5.27 dBi at 2.4 and 5 GHz, respectively. Circular polarization (CP) is effectively realized through the implementation of opposite truncated corners and intentionally located stubs. The 3 dB axial ratio bandwidth (ARBW) is significantly enhanced, while a defected ground structure (DGS) is utilized to further improve the bandwidth and gain. The optimized antenna has overall dimensions of 40 × 40 × 1.6 mm³ and demonstrates a wide −10 dB reflection bandwidth of 5.38% (2.396–2.525 GHz) and 9.26% (4.91–5.38 GHz), along with a broad 3 dB axial ratio bandwidth (ARBW) of 380 MHz (2.29–2.67 GHz) and 80 MHz (5–5.08 GHz). The proposed antenna is fabricated using a low-cost FR-4 substrate with a dielectric constant of 4.4 and a loss tangent of 0.02. The fabricated antenna is experimentally characterized to verify the design concept as well as to validate the simulation results. It is found that the experimental measurements correlate very well with the simulation results. A comparison with comparable designs in the literature shows that the proposed antenna provides a higher gain with a relatively reduced size. Full article

A pattern-reconfigurable, vertically polarized (VP), electrically small (ES), Huygens source antenna (HSA) is demonstrated. A custom-designed reconfigurable inverted-F structure is embedded in a hollowed-out cylindrical dielectric resonator (DR). It radiates VP electric dipole fields that excite the DR’s HEM_11δ mode, which in turn acts as an orthogonal magnetic dipole radiator. The HSA’s unidirectional properties are thus formed. It becomes low-profile and electrically small through a significant lowering of its operational frequency band by loading the DR’s top surface with a metallic disk. The entire 360° azimuth range is covered by each of the HSA’s four 90° reconfigurable states, emitting a unidirectional wide beam. A prototype was fabricated and tested. The measured results, which are in good agreement with their simulated values, demonstrate that the developed wideband Huygens source antenna, with its 0.085 λ_L low profile and its 0.20 λ_L × 0.20 λ_L compact transverse dimensions, hence, electrically small size with ka = 0.89, exhibits a wide 14.1% fractional impedance bandwidth and a 6.1 dBi peak realized gain in all four of its pattern-reconfigurable states. Full article

In this paper, a novel dual-band metasurface filter (MSF) designed for accurately differentiating pulse waves (PWs) and continuous waves (CWs) is proposed, which is based on a complementary cross resonator (CSR) structure adhered on a dielectric substrate integrated with a capacitive nonlinear circuit. The unit cell of the designed dual-band MSF comprises two identical CSR structures: one of the capacitive nonlinear circuits is configured in parallel with a capacitor (C₁) within one CSR structure. These structures loaded with nonlinear circuits are fabricated on a dielectric substrate. The simulation outcomes reveal that, for normally incident CWs with an input power of 10 dBm, the transmittance of the designed dual-band MSF reaches as high as 97.1% at 2.0 GHz and 93.9% at 3.45 GHz. In contrast, when it comes to 50 ns short PWs, the transmittance remains consistently below 6% throughout the entire frequency range from 1 GHz to 5 GHz. In addition, the transmittance of the dual-band MSF for normally incident PWs increases significantly as the pulse width widens at the aforementioned two discrete frequencies. The ensuing simulation data corroborates that within the input power range of −15 to 15 dBm, the transmittance difference between CWs and PWs of the dual-band MSF first rises and then falls as the input power increases. Specifically, when the input power is specified as 10 dBm and the angle of oblique incidence ranges from 0° to 60°, in the context of TE and TM modes, the transmittance of CWs exceeds 80% around both 2.0 GHz and 3.45 GHz, while that of PWs remains below 15%. Finally, the effects of resistance and capacitance on the transmittance of the dual-band MSF for the incident PWs and CWs are also studied. The dual-band MSF proposed herein showcases its potential applications in wireless communication as well as in the realm of anti-electromagnetic interference. The electromagnetic (EM) waveform modulation in the frequency band of 1–5 GHz has great development prospects in low-frequency working fields such as radar antennas and EM protection. Full article

In this article, a chip-fed millimeter-wave high-gain antenna system with in-antenna power combining capability is presented. A low-profile resonant cavity antenna (RCA) array is fed by multiple spherical dielectric resonators (DRs), demonstrating its multi-feed capabilities. Each of the DRs is fed by two microstrip resonators on a planar circuit board. A printed superstrate is used in the proposed RCA as the partially reflecting superstrate (PRS), which makes the antenna profile small. To increase the directivity and gain, a 2 × 2 RCA array is developed. The demonstrated design shows a prominent peak gain of 25.03 dBi, a radiation efficiency of more than 80% and 3.38 GHz 3 db gain-bandwidth while maintaining a low profile. To steer the beam of the demonstrated 2 × 2 RCA array in a wide angular range with a low side-lobe-level, two planar all-dielectric passive beam steering metasurfaces have been designed and optimized. A detailed analysis of the optimization procedure is presented in this article. This numerical investigation is vitally important for realizing beam steering metasurfaces with suppressed side-lobe-level, wide bandwidth, excellent efficiency and less complexity. Full article

The literature reports highlight the transmission field (B₁⁺) uniformity and efficiency constraints of cardiac magnetic resonance imaging (MRI) at ultrahigh magnetic fields (UHF). This simulation study proposes a 3D Metamaterial (MM) to address these challenges. The study proposes a 3D MM consisting of unit cells (UC) with split ring resonator (SRR) layers immersed in dielectric material glycerol. Implementing the proposed MM design aims to reduce the effective thickness and weight of the dielectric material while shaping B₁⁺ and improving the penetration depth. The latter is dictated by the chosen array size, where small local UC arrays can focus B₁⁺ and larger UC arrays can increase the field of view, at the cost of a lower penetration depth. Designing RF antennas that can effectively transmit at 21.0 T while maintaining patient safety and comfort is challenging. Using Self-Grounded Bow-Tie (SGBT) antennas in conjunction with the proposed MM demonstrated enhanced B₁⁺ efficiency and uniformity across the human heart without signal voids. The study employed dynamic parallel transmission with tailored kT points to homogenize the 3D flip angle over the whole heart. This proof-of-concept study provides the technical foundation for human cardiac MRI at 21.0 T. Such numerical simulations are mandatory precursors for the realization of whole-body human UHF MR instruments. Full article

This article presents a circular polarized enclosed dielectric resonator antenna (DRA), operating at 5.8 GHz. The design consists of a twist DRA, which is enclosed in a box to give stability to the structure. The circular polarization of the antenna depends on the sense of twisting the top with respect to its base to achieve Left Hand Circular Polarization (LHCP) or Right Hand Circular Polarization (RHCP). The antenna was manufactured using 3D printing and low-loss dielectric filament. The measurement results show the two resonance frequencies and an axial ratio below 3 dB at the operational frequency, while exhibiting a bandwidth and gain compatible for unmanned aerial vehicle (UAV) applications. Full article