Search Results (21)

Measuring pH with an optical sensor requires the immobilization of a chemical recognition phase on a solid surface. Neutral red (NR), an acid base indicator was used to develop two different optical probe configurations. The chemistry of aryl diazonium salts was chosen for the elaboration of this chemical phase, as it enables strong covalent bonds to be established on the surface of metallized glass or metallic surfaces. It also allows the formation of a thick film required to obtain an exploitable spectral response. The surfaces of interest (metallized optical fiber and 316 L stainless-steel mirror) are modelized by flat surfaces (metallized glass plates and 316 L stainless-steel plates). The analytical characterizations carried out (IR, XPS, UV-Visible, and profilometry) show that NR was covalently grafted onto the model surfaces as well as on the surfaces of interest. The supports grafted with NR to develop optical pH probes exhibit spectral changes, particularly the values of pKa, the pH range, and the isosbestic point wavelength. The experimental results show that the optical probe can be used for pH measurements between 4 and 8. Full article

In the pursuit of designing a reusable catalyst with enhanced catalytic activity, recent studies indicate that electrochemical grafting of diazonium salts is an efficient method of forming heterogeneous catalysts. The aim of this review is to assess the industrial applicability of diazonium-based catalysts with particular emphasis on their mechanical, chemical, and thermal stability. To this end, different approaches to catalyst production via diazonium salt chemistry have been compared, including the immobilization of catalysts by a chemical reaction with a diazonium moiety, the direct use of diazonium salts and nanoparticles as catalysts, the use of diazonium layers to modulate wettability of a carrier, as well as the possibility of transforming the catalyst into the corresponding diazonium salt. After providing descriptions of the most suitable carriers, the most common deactivation routes of catalysts have been discussed. Although diazonium-based catalysts are expected to exhibit good stability owing to the covalent bond created between a catalyst and a post-diazonium layer, this review indicates the paucity of studies that experimentally verify this hypothesis. Therefore, use of diazonium salts appears a promising approach in catalysts formation if more research efforts can focus on assessing their stability and long-term catalytic performance. Full article

In this proof-of-concept study, gold nanoparticles (AuNPs) were immobilized on glassy carbon electrode (GCE) surfaces using a surface-anchored diazonium salt of 4-aminothiophenol (GCE-Ph-S-AuNPs). X-ray photoelectron spectroscopy (XPS) studies confirmed the attachment of the AuNPs via 4-thiophenol onto the surface of the modified electrode. Differential pulse voltammetry (DPV) was performed for the simultaneous determination of guanine (G) and 8-hydroxyguanine (8-OH-G). The calibration curves were linear up to 140 µM and 60 µM with a limit of detection of 0.02 µM and 0.021 µM for G and 8-OH-G, respectively. Moreover, chronoamperometric studies were carried out for the determination of diffusion coefficients of 8-OH-G and G. The GCE-Ph-S-AuNPs were also applied in genomic DNA-spiked samples for the determination of G and 8-OH-G with recovery rates between 98.5% and 103.3%. The novel electrochemical surface provided a potential platform for the sensitive detection of 8-OH-G related to oxidative stress-induced DNA damage in clinical studies. Full article

Early diagnosis is highly crucial for life-saving and transmission management of tuberculosis (TB). Despite the low sensitivity and time-consuming issues, TB antigen detection still relies on conventional smear microscopy and culture techniques. To address this limitation, we report the development of the first amperometric dual aptasensor for the simultaneous detection of Mycobacterium tuberculosis secreted antigens CFP10 and MPT64 for better diagnosis and control of TB. The developed sensor was based on the aptamers–antibodies sandwich assay and detected by chronoamperometry through the electrocatalytic reaction between peroxidase-conjugated antibodies, H₂O₂, and hydroquinone. The CFP10 and MPT64 aptamers were immobilized via carbodiimide covalent chemistry over the disposable dual screen-printed carbon electrodes modified with a 4-carboxyphenyl diazonium salt. Under optimized conditions, the aptasensor achieved a detection limit of 1.68 ng mL⁻¹ and 1.82 ng mL⁻¹ for CFP10 and MPT64 antigens, respectively. The developed assay requires a small sample amount (5 µL) and can be easily performed within 2.5 h. Finally, the dual aptasensor was successfully applied to clinical sputum samples with the obtained diagnostic sensitivity (n = 24) and specificity (n = 13) of 100%, respectively, suggesting the readiness of the developed assay to be used for TB clinical application. Full article

Curbing tuberculosis (TB) requires a combination of good strategies, including a proper prevention measure, diagnosis, and treatment. This study proposes an improvised tuberculosis diagnosis based on an amperometry approach for the sensitive detection of MPT64 antigen in clinical samples. An MPT64 aptamer specific to the target antigen was covalently attached to the carboxyphenyl diazonium-functionalized carbon electrode via carbodiimide chemistry. The electrochemical detection assay was adapted from a sandwich assay format to trap the antigen between the immobilized aptamer and horseradish peroxidase (HRP) tagged polyclonal anti-MPT64 antibody. The amperometric current was measured from the catalytic reaction response between HRP, hydrogen peroxide, and hydroquinone, which is used as an electron mediator. From the analysis, the detection limit in the measurement buffer was 1.11 ng mL⁻¹. Additionally, the developed aptasensor exhibited a linear relationship between the current signal and the MPT64 antigen-spiked serum concentration ranging from 10 to 150 ng mL⁻¹ with a 1.38 ng mL⁻¹ detection limit. Finally, an evaluation using the clinical sputum samples from both TB (+) and TB (−) individuals revealed a sensitivity and specificity of 88% and 100%, respectively. Based on the analysis, the developed aptasensor was found to be simple in its fabrication, sensitive, and allowed for the efficient detection and diagnosis of TB in sputum samples. Full article

Herein, we investigated the effect of the support modification (Sibunit carbon) with diazonium salts of Pd and Pd-Au catalysts on furfural hydrogenation under 5 bars of H₂ and 50 °C. To this end, the surface of Sibunit (Cp) was modified with butyl (Cp-Butyl), carboxyl (Cp-COOH) and amino groups (Cp-NH₂) using corresponding diazonium salts. The catalysts were synthesized by the sol immobilization method. The catalysts as well as the corresponding supports were characterized by Fourier transform infrared spectroscopy, N₂ adsorption-desorption, inductively coupled plasma atomic emission spectroscopy, high resolution transmission electron microscopy, energy dispersive spectroscopy, X-ray diffraction, Hammet indicator method and X-ray photoelectron spectroscopy. The analysis of the results allowed us to determine the crucial influence of surface chemistry on the catalytic behavior of the studied catalysts, especially regarding selectivity. At the same time, the structural, textural, electronic and acid–base properties of the catalysts were practically unaffected. Thus, it can be assumed that the modification of Sibunit with various functional groups leads to changes in the hydrophobic/hydrophilic and/or electrostatic properties of the surface, which influenced the selectivity of the process. Full article

Herein, a novel hybrid bilayer membrane is introduced as a platform to study the aggregation of amyloid-β_1–42 (Aβ_1–42) peptide on surfaces. The first layer was covalently attached to a glassy carbon electrode (GCE) via diazonium electrodeposition, which provided a highly stable template for the hybrid bilayer formation. To prepare the long-chain hybrid bilayer membrane (lcHBLM)-modified electrodes, GCE surfaces were modified with 4-dodecylbenzenediazonium (DDAN) followed by the modification with dihexadecyl phosphate (DHP) as the second layer. For the preparation of short-chain hybrid bilayer membrane (scHBLM)-modified electrodes, GCE surfaces were modified with 4-ethyldiazonium (EDAN) as the first layer and bis(2-ethylhexyl) phosphate (BEHP) was utilized as the second layer. X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were used to characterize the bilayer formation. Both positively charged [Ru(NH₃)₆]³⁺ and negatively charged ([Fe(CN)₆]^3-/4-) redox probes were used for electrochemical characterization of the modified surfaces using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). EIS results showed a decrease in charge transfer resistance (R_ct) upon incubation of Aβ_1–42 on the hybrid bilayer-modified surfaces. This framework provides a promising electrochemical platform for designing hybrid bilayers with various physicochemical properties to study the interaction of membrane-bound receptors and biomolecules on surfaces. Full article

In this paper, we propose an improved electrochemical platform based on graphene for the detection of DNA hybridization. Commercial screen-printed carbon electrodes (SPCEs) were used for this purpose due to their ease of functionalization and miniaturization opportunities. SPCEs were modified with reduced graphene oxide (RGO), offering a suitable surface for further functionalization. Therefore, aryl-carboxyl groups were integrated onto RGO-modified electrodes by electrochemical reduction of the corresponding diazonium salt to provide enough reaction sites for the covalent immobilization of amino-modified DNA probes. Our final goal was to determine the optimum conditions needed to fabricate a simple, label-free RGO-based electrochemical platform to detect the hybridization between two complementary single-stranded DNA molecules. Each modification step in the fabrication process was monitored by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) using [Fe(CN)₆]^3−/4− as a redox reporter. Although, the diazonium electrografted layer displayed the expected blocking effect of the charge transfer, the next steps in the modification procedure resulted in enhanced electron transfer properties of the electrode interface. We suggest that the improvement in the charge transfer after the DNA hybridization process could be exploited as a prospective sensing feature. The morphological and structural characterization of the modified electrodes performed by scanning electron microscopy (SEM) and Raman spectroscopy, respectively, were used to validate different modification steps in the platform fabrication process. Full article

Circulating tumour DNA (ctDNA) is widely used in liquid biopsies due to having a presence in the blood that is typically in proportion to the stage of the cancer and because it may present a quick and practical method of capturing tumour heterogeneity. This paper outlines a simple electrochemical technique adapted towards point-of-care cancer detection and treatment monitoring from biofluids using a label-free detection strategy. The mutations used for analysis were the KRAS G12D and G13D mutations, which are both important in the initiation, progression and drug resistance of many human cancers, leading to a high mortality rate. A low-cost DNA sensor was developed to specifically investigate these common circulating tumour markers. Initially, we report on some developments made in carbon surface pre-treatment and the electrochemical detection scheme which ensure the most sensitive measurement technique is employed. Following pre-treatment of the sensor to ensure homogeneity, DNA probes developed specifically for detection of the KRAS G12D and G13D mutations were immobilized onto low-cost screen printed carbon electrodes using diazonium chemistry and 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride/N-hydroxysuccinimide coupling. Prior to electrochemical detection, the sensor was functionalised with target DNA amplified by standard and specialist PCR methodologies (6.3% increase). Assay development steps and DNA detection experiments were performed using standard voltammetry techniques. Sensitivity (as low as 0.58 ng/μL) and specificity (>300%) was achieved by detecting mutant KRAS G13D PCR amplicons against a background of wild-type KRAS DNA from the representative cancer sample and our findings give rise to the basis of a simple and very low-cost system for measuring ctDNA biomarkers in patient samples. The current time to receive results from the system was 3.5 h with appreciable scope for optimisation, thus far comparing favourably to the UK National Health Service biopsy service where patients can wait for weeks for biopsy results. Full article

The multifaceted key roles of cytokines in immunity and inflammatory processes have led to a high clinical interest for the determination of these biomolecules to be used as a tool in the diagnosis, prognosis, monitoring and treatment of several diseases of great current relevance (autoimmune, neurodegenerative, cardiac, viral and cancer diseases, hypercholesterolemia and diabetes). Therefore, the rapid and accurate determination of cytokine biomarkers in body fluids, cells and tissues has attracted considerable attention. However, many currently available techniques used for this purpose, although sensitive and selective, require expensive equipment and advanced human skills and do not meet the demands of today’s clinic in terms of test time, simplicity and point-of-care applicability. In the course of ongoing pursuit of new analytical methodologies, electrochemical biosensing is steadily gaining ground as a strategy suitable to develop simple, low-cost methods, with the ability for multiplexed and multiomics determinations in a short time and requiring a small amount of sample. This review article puts forward electrochemical biosensing methods reported in the last five years for the determination of cytokines, summarizes recent developments and trends through a comprehensive discussion of selected strategies, and highlights the challenges to solve in this field. Considering the key role demonstrated in the last years by different materials (with nano or micrometric size and with or without magnetic properties), in the design of analytical performance-enhanced electrochemical biosensing strategies, special attention is paid to the methods exploiting these approaches. Full article

Liquid biopsies are becoming increasingly important as a potential replacement for existing biopsy procedures which can be invasive, painful and compromised by tumour heterogeneity. This paper reports a simple electrochemical approach tailored towards point-of-care cancer detection and treatment monitoring from biofluids using a label-free detection strategy. The mutations under test were the KRAS G12D and G13D mutations, which are both important in the development and progression of many human cancers and which have a presence that correlates with poor outcomes. These common circulating tumour markers were investigated in clinical samples and amplified by standard and specialist PCR methodologies for subsequent electrochemical detection. Following pre-treatment of the sensor to present a clean surface, DNA probes developed specifically for detection of the KRAS G12D and G13D mutations were immobilized onto low-cost carbon electrodes using diazonium chemistry and 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride/N-hydroxysuccinimide coupling. Following the functionalisation of the sensor, it was possible to sensitively and specifically detect a mutant KRAS G13D PCR product against a background of wild-type KRAS DNA from the representative cancer sample. Our findings give rise to the basis of a simple and very low-cost system for measuring ctDNA biomarkers in patient samples. The current time to result of the system was 3.5 h with considerable scope for optimisation, and it already compares favourably to the UK National Health Service biopsy service where patients can wait weeks for their result. This paper reports the technical developments we made in the production of consistent carbon surfaces for functionalisation, assay performance data for KRAS G13D and detection of PCR amplicons under ambient conditions. Full article

The challenges of diazonium salts stabilization have been overcome by their isolation as metal salts such as tetrachloroaurate(III). The cleavage of molecular nitrogen from diazonium salts even at very low potential or on reducing surfaces by fine tuning the substituents on the phenyl ring expanded their applications as surface modifiers in forensic science, nanomedicine engineering, catalysis and energy. The robustness of the metal–carbon bonding produced from diazonium salts reduction has already opened an era for further applications. The integration of experimental and calculations in this field catalyzed its speedy progress. This review provides a narrative of the progress in this chemistry with stress on our recent contribution, identifies potential applications, and highlights the needs in this emerging field. For these reasons, we hope that this review paper serves as motivation for others to enter this developing field of surface modification originating from diazonium salts. Full article

Highly sensitive multicomponent materials designed for the recognition of hazardous compounds request control over interfacial chemistry. The latter is a key parameter in the construction of the sensing (macro) molecular architectures. In this work, multi-walled carbon nanotubes (CNTs) were deposited on diazonium-modified, flexible indium tin oxide (ITO) electrodes prior to the electropolymerization of pyrrole. This three-step process, including diazonium electroreduction, the deposition of CNTs and electropolymerization, provided adhesively-bonded, polypyrrole-wrapped CNT composite coatings on aminophenyl-modified flexible ITO sheets. The aminophenyl (AP) groups were attached to ITO by electroreduction of the in-situ generated aminobenzenediazonium compound in aqueous, acidic medium. For the first time, polypyrrole (PPy) was electrodeposited in the presence of both benzenesulfonic acid (dopant) and ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA), which acts as a chelator. The flexible electrodes were characterized by XPS, Raman and scanning electron microscopy (SEM), which provided strong supporting evidence for the wrapping of CNTs by the electrodeposited PPy. Indeed, the CNT average diameter increased from 18 ± 2.6 nm to 27 ± 4.8, 35.6 ± 5.9 and 175 ± 20.1 after 1, 5 and 10 of electropolymerization of pyrrole, respectively. The PPy/CNT/NH₂-ITO films generated by this strategy exhibit significantly improved stability and higher conductivity compared to a similar PPy coating without any embedded CNTs, as assessed by from electrochemical impedance spectroscopy measurements. The potentiometric response was linear in the 10⁻⁸–3 × 10⁻⁷ mol L⁻¹ Pb(II) concentration range, and the detection limit was 2.9 × 10⁻⁹ mol L⁻¹ at S/N = 3. The EGTA was found to drastically improve selectivity for Pb(II) over Cu(II). To account for this improvement, the density functional theory (DFT) was employed to calculate the EGTA–metal ion interaction energy, which was found to be −374.6 and −116.4 kJ/mol for Pb(II) and Cu(II), respectively, considering solvation effects. This work demonstrates the power of a subtle combination of diazonium coupling agent, CNTs, chelators and conductive polymers to design high-performance electrochemical sensors for environmental applications. Full article

The functionalization of carbon nanotubes (CNTs) plays a key role in their solubilization and compatibility for many applications. Among the many possible ways to functionalize CNTs, the creation of an Si–O–C bond is crucial for the formation of silicone composites. Catalyst-mediated silylesterification is useful in creating Si–O–C bonds because it is cost-effective and uses a hydrosilane precursor of lower reactivity than that of chlorosilane. However, it was previously demonstrated that two important silylesterification catalysts (zinc chloride and Karstedt’s catalyst) exhibit different selectivity for oxidized functional groups that are present on the surface of CNTs after oxidative acid treatment. This report details the selective modification of CNTs with various oxygenated functional groups (aromatic and nonaromatic alcohols, carboxylic acids, ethers, and ketones) using diazonium chemistry. Modified CNTs were used to assess the specifity of zinc chloride and Karstedt’s catalyst for oxygenated functional groups during a silylesterification reaction. Karstedt’s catalyst appeared to be widely applicable, allowing for the silylesterification of all of the aforementioned oxygenated functional groups. However, it showed lower efficacy for ethers and ketones. By contrast, zinc chloride was found to be very specific for nonaromatic carboxylic acids. This study also examined the Hansen solubility parameters of modified CNTs. Full article

Silicon/carbon (Si/C) composite has been proven to be an effective method of enhancing the electrochemical performance of Si-based anodes for lithium-ion batteries (LIBs). However, the practical application of Si/C materials in LIBs is difficult because of the weak interaction between Si and C. In this study, we applied two-step diazotization reactions to modify graphite nanosheets (GNs) and Si nanoparticles (Si NPs), yielding a stable Si–Ar–GNs composite. Owing to aryl (Ar) group bonding, Si NPs were dispersed well on the GNs. The as-prepared Si–Ar–GNs composite delivered an initial reversible capacity of 1174.7 mAh·g⁻¹ at a current density of 100 mAh·g⁻¹. Moreover, capacity remained at 727.3 mAh·g⁻¹ after 100 cycles, showing improved cycling performance. This synthesis strategy can be extended to prepare other Si/C anode materials of LIBs. Full article