Search Results (447)

Turbidite lobe reservoirs represent critical deep-sea hydrocarbon targets, yet preferred seepage channels within them remain poorly characterized. This paper establishes a method for identifying internal preferred seepage channels in turbidite lobe reservoirs using data including seismic, core, thin section, logging, and production performance, combined with neural network technology. A neural network model for predicting reservoir productivity types can be obtained by taking the average logging data of reservoir intervals as input and the reservoir productivity types categorized by meter oil production index calculated by actual production data as the target. By applying the trained neural network model and inputting actual logging attribute model, the reservoir productivity types of single wells are obtained. Using the attribute model of natural gamma ray, acoustic, neutron, density, deep lateral, and shallow lateral logs, which are built by using the actual logging data and Sequential Gaussian Simulation, and supervising with the single well reservoir productivity type, the reservoir productivity type at any position in the reservoir can be predicted. It predicts their spatial distribution characteristics, reveals the genetic mechanism of preferred seepage channels, and discusses the significance of identifying preferred seepage channels for oilfield development. The results show that the reservoir productivity types in the study area can be divided into five categories with progressive improvement in productivity (A, B, C, D, and E) according to the increase in oil production index per meter, among which Type E reservoirs represent typical preferred seepage channels. The attribute model of reservoir productivity types indicates that, horizontally, types E and B are locally developed in the study area, while types D, C, and A are widely distributed. The preferred seepage channels can be divided into two types according to the shape: zonal (length to width > 2:1) and sheet-like (length to width ≤ 2:1). Vertically, types C, D, and E are relatively well-developed in layers III and IV, whereas types A and B are more common in layers I and II. The vertical combination patterns of preferred seepage channels reveal four types, including homogeneous, bottom-dominated, top-dominated, and interbedded patterns. The formation of preferred seepage channels is influenced by both sedimentary and diagenetic processes, and sedimentary is the most important controlling factors. The identification of preferred seepage channels in turbidite lobe reservoirs is of great significance for formulating development policies and tapping remaining oil. Full article

The development of gravity flow sedimentology has improved our understanding of the physical properties of different types of gravity flow deposits, especially the advancement of various gravity flow models. Although studies of gravity flows have developed greatly, the linkage between different sub-facies and their reservoir properties is hindered by a lack of detailed sedimentary records. Here, integrated test data (including thin-section petrology, high-pressure mercury injection experiments, capillary pressure curve analysis, and scanning electron microscopy) are used to evaluate links between different types of gravity flows and their reservoir properties from the Late Triassic–Early Jurassic Anyao Formation, southeastern Paleo-Ordos Basin, China. The petrological and sedimentological data reveal two types of deep-water gravity flow deposits comprising sandy debris flow (SDF) and turbidity current (TC) deposits. Both are fine-grained lithic sandstones and form low-porosity and ultra-low permeability reservoirs. Secondary porosity, formed by the dissolution of framework grains, including feldspars and lithic fragments, dominates the pore types. This secondary porosity is widely developed in the Anyao Formation and formed by reaction with organic acids during burial (early mesodiagenesis). The associated mud rocks have reached the early mature stage of the oil window with Tmax of 442–448 °C. Compared with the turbidites, the sandy debris flows have higher framework grain content (87.9 vs. 84.8%), framework grain size (0.091 vs. 0.008 mm), porosity (6.97 vs. 3.44%), pore throat radius (0.102 vs. 0.025 μm), and permeability (0.025 vs. 0.005 mD) but are relatively poor in the sorting of framework grains and pore throat radii. The most important petrological factors affecting porosity and permeability of the SDF reservoirs are framework grain size and feldspar grain content, respectively, but those of the TC reservoirs are feldspar grain content and the maximum pore throat radius. Diagenetic dissolution of framework grains is the most important porosity-affecting factor for both SDF and TC reservoirs. Our multi-proxy study provides new insights into the links between gravity flow sub-facies and reservoir properties in the lacustrine deep-water environment. Full article

Laser-induced breakdown spectroscopy (LIBS) has been used to explore the chemistry of three regions of Mars on respective missions by NASA and CNSA, with CNES contributions. All three LIBS instruments use ~100 mm diameter telescopes projecting pulsed infrared laser beams of 10–14 mJ to enable LIBS at 2–10 m distances, eliminating the need to position the rover and instrument directly onto targets. Over 1.3 million LIBS spectra have been used to provide routine compositions for eight major elements and several minor and trace elements on >3000 targets on Mars. Onboard calibration targets common to all three instruments allow careful intercomparison of results. Operating over thirteen years, ChemCam on Curiosity has explored lacustrine sediments and diagenetic features in Gale crater, which was a long-lasting (>1 My) lake during Mars’ Hesperian period. SuperCam on Perseverance is exploring the ultramafic igneous floor, fluvial–deltaic features, and the rim of Jezero crater. MarSCoDe on the Zhurong rover investigated for one year the local blocks, soils, and transverse aeolian ridges of Utopia Planitia. The pioneering work of these three stand-off LIBS instruments paves the way for future space exploration with LIBS, where advantages of light-element (H, C, N, O) quantification can be used on icy regions. Full article

The Mindong–Changchunling region is situated in the central portion of the Songliao Basin, Northeast China. The primary target stratum in this area is the Fuyu Oil Layer of the Lower Cretaceous Quantou 4 Member. This reservoir is predominantly composed of fine sandstone and siltstone, with minor interbedded medium sandstone. Variations in provenance, sedimentation, and diagenesis are identified as the main controlling factors for the distribution of high-quality reservoirs in the Mindong–Changchunling region. The sand body distribution in the Changchunling area is influenced by the eastern near-source provenance. The reservoir properties of these sand bodies are impacted by the poor sorting and high mud content typical of near-source delta sand bodies. Nonetheless, reservoir quality is enhanced by late-stage uplift and surface water dissolution-leaching. In contrast, sand body distribution in the Mindong area is governed by the southwestern far-source provenance. Far-source delta sand bodies are characterized by better sorting but high mud content, with their reservoir properties primarily impaired by carbonate cementation. During the early-middle diagenetic stage, feldspar dissolution by organic acids improves sand body reservoir quality. Due to variations in sedimentation and diagenesis, the following three favorable reservoir zones with distinct genetic types have developed in the Mindong–Changchunling area: the Chang107–Chang104–Chang52 well block, the Fu155–Fu161–Fu157 well block, and the Min103–Min31 well block. Full article

The Dongping manganese (Mn) deposit, located within the Lower Triassic Shipao Formation of the Youjiang Basin, is one of South China’s most significant sedimentary Mn carbonate ore deposits. To resolve longstanding debates over its metallogenic pathway, we conducted integrated sedimentological, mineralogical, and geochemical analyses on three drill cores (ZK5101, ZK0301, and ZK1205) spanning the Mn ore body. X-ray diffraction and backscatter electron imaging reveal that the ores are dominated by kutnohorite, with subordinate quartz, calcite, dolomite, and minor sulfides. The low enrichment of U/Al, V/Al, and Mo/Al, as well as positive Ce anomalies, consistently suggest that Mn, in the form of oxides, was deposited in an oxic water column. Carbon isotope compositions of Mn carbonate ores (δ¹³C_VPDB: −2.3 to −6.1‰) and their negative correlation with MnO suggest that Mn carbonate, predominantly kutnohorite, show a diagenetic reduction in pre-existing Mn oxides via organic-matter oxidation in anoxic sediments pore waters. Elemental discrimination diagramms (Mn-Fe-(Co+Ni+Cu) × 10 and Co/Zn vs. Co+Cu+Ni) uniformly point to a hydrothermal Mn source. We therefore propose that hydrothermal fluids supplied dissolved Mn²⁺ to an oxic slope-basin setting, precipitating initially as Mn oxides, which were subsequently transformed to Mn carbonates during early diagenesis. This model reconciles both the hydrothermal and sedimentary-diagenetic processes of the Dongping Mn deposit. Full article

The Chating Cu-Au and Magushan Cu-Mo deposits in Anhui province are two representative deposits within the recently defined Nanling-Xuancheng ore concentration area in the Middle and Lower Yangtze River Metallogenic Belt (MLYB). Magmatism and mineralization for the area are not well known at present due to a lack of in-depth studies on the petrogenesis of ore-bearing intrusive rocks and their relationship with deposits. Here, the ore-bearing intrusive rocks of the two deposits are investigated through analyses of whole-rock geochemistry and Sr-Nd isotopes, zircon U-Pb ages, and zircon Hf isotopes. The results reflect the two intrusions, both formed in the Early Cretaceous (138.9 ± 0.8 Ma and 132.2 ± 1.3 Ma). They belong to the sub-alkaline high-K calc-alkaline series, while trace elements are enriched in LILEs and LREE and depleted in HFSEs. However, the intrusions of the Chating deposit (I_sr = 0.7064–0.7068; ε_Nd(t) = −8.5–−7.3; ε_Hf(t) = −11.9–−7.0) have obviously different Sr-Nd-Hf isotopic compositions from the intrusions of the Magushan deposit (I_sr = 0.7079–0.7081; ε_Nd(t) = −5.7–−5.4; ε_Hf(t) = −5.4–−3.6). The characteristics indicate that the two intrusions were formed in the same diagenetic ages and tectonic settings and derived from a crust–mantle mixture with predominant mantle-derived materials. But the crust materials of sources are different, which further leads to different metallogenic elements, showing that the Chating deposit is enriched in Cu and Au, while the Magushan deposit is enriched in Mo. Moreover, the characteristics and magma sources of two intrusions and metallogenic elements correspond respectively to the Tongling Cu-Au polymetallic ore concentration area in the MLYB and the southern Anhui Mo polymetallic ore concentration area in the Jiangnan orogen. The correlation implies differences in magmatism and mineralization between the northwestern and southeastern parts of the Nanling-Xuancheng ore concentration area, demarcated by the Jiangnan Deep Fault. These variations were mainly controlled by the Pre-Sinian crustal basement. Full article

Isotopic investigations focused on determining the mobility and provenance of ancient human civilizations and sourcing of archeological artifacts continue to gain prominence in archeology. Most studies focus on the premise that the geographic variation in isotope systems of interest (e.g., Sr, Pb, Nd, O) in the natural environment is recorded in both human hard tissues of local individuals and raw materials sourced for artifacts within the same region. The introduction of multi-collection–inductively coupled plasma mass spectrometry (MC-ICP-MS) and laser ablation systems are techniques that consume smaller sample sizes compared to previous mass spectrometric approaches due to their higher ionization efficiency and increased sensitivity. This development has facilitated the isotopic measurement of trace elements present at low abundances (e.g., Pb, Nd, <1-to-low ppm range) particularly in human tooth enamel. Accurate interpretation of any isotope ratio measurement for the proveniencing of such low-abundance samples requires the adequate evaluation of post-mortem diagenetic alteration. A synopsis of practices currently in use for identifying post-mortem alteration in human archeological samples is discussed here. Post-mortem shifts in radiogenic isotope signatures resulting from secondary alteration are distinct from those potentially related to the impact of climate change on the bioavailable budgets for these elements. This topic is of interest to the archeological community and discussed here in the context of Holocene-aged samples from burial sites within the Nile River Valley System, and preferred dust source areas from the neighboring Sahara Desert. Full article

The geochemistry of the fatty acids in the modern sediments in the Northern South Yellow Sea is still poorly studied, and studies on the geochemistry of the fatty acids in relatively long-core sediment samples are lacking. Thus, the fatty acids in the core sediments in the Northern South Yellow Sea were separated and identified to study their components and distribution characteristics, and the sources of organic matter and the early diagenetic evolution of the fatty acids in the sediments were discussed. The results show that saturated straight-chain fatty acids (methyl ester) have the highest content in the core sediments in the Northern South Yellow Sea, which account for 83.89% of the total fatty acids (methyl ester). nC_16:0 is dominant, accounting for 30.48% of the n-saturated fatty acids (methyl ester). Unsaturated fatty acids (methyl ester) account for 7.59% of the total fatty acids (methyl ester). Binary unsaturated fatty acids (methyl ester) can only be detected in some samples, which are low in content and dominated by C_18:2. Based on the components and distribution of the fatty acids (methyl ester) in the core sediments in the Northern South Yellow Sea, combined with the characteristics of other lipid biomarker compounds, the actual geological background, and previous research results, it is considered that the sources of organic matter in the core sediments are marine–terrestrial mixed materials, with terrestrial materials dominating. The fatty acids’ (methyl ester) CPI, the relative content of short-chain saturated fatty acids (methyl ester), and the unsaturated fatty acids (methyl ester) in the core sediments show non-obvious variation as the burial depth increases, reflecting that the fatty acids in the core sediments are strongly degraded at the early diagenetic stage, and this degradation is controlled by various complicated factors. Full article

This study focuses on the clastic reservoir in the first member of Yaojia Formation within Qijia-Gulong Sag, Songliao Basin. The results indicate that the reservoir in the study area develops within a shallow-water delta sedimentary system. The dominant sedimentary microfacies comprise underwater distributary channels, mouth bars, and sheet sands. Among these, the underwater distributary channel microfacies exhibits primary porosity ranging from 15.97% to 17.71%, showing the optimal reservoir quality, whereas the sheet sand microfacies has a porosity of only 7.45% to 12.08%, indicating inferior physical properties. During diagenesis, compaction notably decreases primary porosity via particle rearrangement and elastic deformation, while calcite cementation and quartz overgrowth further occlude pore throats. Although dissolution can generate secondary porosity (locally up to 40%), the precipitation of clay minerals tends to block pore throats, leading to “ineffective porosity” (permeability generally < 5 mD) and overall low-porosity and low-permeability characteristics. Carbon–oxygen isotope analysis reveals a deficiency in organic acid supply in the study area, restricting the intensity of dissolution alteration. Reservoir quality evolution is dominantly governed by the combined controls of sedimentary microfacies and diagenesis. This study emphasizes that, within shallow-water delta sedimentary settings, the material composition of sedimentary microfacies and the dynamic equilibrium of diagenetic processes jointly govern reservoir property variations. This insight provides critical theoretical support for understanding diagenetic evolution mechanisms in clastic reservoirs and enabling precise prediction of high-quality reservoir distribution. Full article

Fossil resins from the area of Gulf of Gdańsk, Lublin area, Denmark, Bitterfeld, Lusatia and Ukraine, often grouped under the collective term ‘Baltic amber’, are complex organic mineraloids that have undergone various post-depositional transformations. Despite their role in paleontology as a source of for biological inclusions, fossil resins themselves are rarely analyzed as taphonomic objects. In this work, a new geochemical approach to fossil resin taphonomy is presented. Applying the van Krevelen diagram—traditionally used for kerogen classification—allows the diagenetic and catagenetic changes of fossilized resin maturation to be evaluated. Based on literature-derived elemental composition data of C, H, and O contents of ‘Baltic amber’, the diagram is interpreted as an organic matter transformation framework of fossil resins. The results suggest that the so-called ‘Baltic amber’ deposits represent a composite taphocoenoses of resins with different burial histories and maturation scenarios. This approach integrates petrological classification, geochemical maturation, and taphonomic analyses, offering a new way of “tracking” fossil resins maturation changes. Full article

Stylolites are ubiquitous diagenetic products in carbonate rocks. They play a significant role in enhancing or reducing fluid flow in subsurface reservoirs. This study unravels the relationship between stylolite networks, carbonate microfacies, and the elemental geochemistry of Upper Cretaceous limestones of the Kometan Formation (shallow to moderately deep marine) in Northern Iraq. Stylolites exhibit diverse morphologies across mud- and grain-supported limestone facies. Statistical analyses of stylolite spacing, wavelength, amplitude, and their intersections and connectivity indicate that grain size, sorting, and mineral composition are key parameters that determine the geometrical properties of the stylolites and stylolite networks. Stylolites typically exhibit weak connectivity and considerable vertical spacing when hosted in packstone facies with moderate grain sorting. Conversely, mud-supported limestones, marked by poor sorting and high textural heterogeneity, host well-developed stylolite networks characterized by high amplitude and frequent intersections, indicating significant dissolution and deformation processes. Stylolites in mud-supported facies are closely spaced and present heightened amplitudes and intensified junctions, with suture and sharp-peak type. This study unveils that stylolites can potentially enhance porosity in the studied formation. Full article

The investigation of the pore structure and fractal characteristics of coal-bearing shale is critical for unraveling reservoir heterogeneity, storage-seepage capacity, and gas occurrence mechanisms. In this study, 12 representative Upper Paleozoic coal-bearing shale samples from the Yangquan Block of the Qinshui Basin were systematically analyzed through field emission scanning electron microscopy (FE-SEM), high-pressure mercury intrusion, and gas adsorption experiments to characterize pore structures and calculate multi-scale fractal dimensions (D₁–D₅). Key findings reveal that reservoir pores are predominantly composed of macropores generated by brittle fracturing and interlayer pores within clay minerals, with residual organic pores exhibiting low proportions. Macropores dominate the total pore volume, while mesopores primarily contribute to the specific surface area. Fractal dimension D₁ shows a significant positive correlation with clay mineral content, highlighting the role of diagenetic modification in enhancing the complexity of interlayer pores. D₂ is strongly correlated with the quartz content, indicating that brittle fracturing serves as a key driver of macropore network complexity. Fractal dimensions D₃–D₅ further unveil the synergistic control of tectonic activity and dissolution on the spatial distribution of pore-fracture systems. Notably, during the overmature stage, the collapse of organic pores suppresses mesopore complexity, whereas inorganic diagenetic processes (e.g., quartz cementation and tectonic fracturing) significantly amplify the heterogeneity of macropores and fractures. These findings provide multi-scale fractal theoretical insights for evaluating coal-bearing shale gas reservoirs and offer actionable recommendations for optimizing the exploration and development of Upper Paleozoic coal-bearing shale gas resources in the Yangquan Block of the Qinshui Basin. Full article

The Carboniferous–Permian tight sandstone gas reservoirs in the Shenfu area of the Ordos Basin in China are characterized by the widespread development of multiple formations. However, significant differences exist among the tight sandstones of different formations, and their formation mechanisms and key controlling factors remain unclear, hindering the effective selection and development of favorable tight gas intervals in the study area. Through comprehensive analysis of casting thin section (CTS), scanning electron microscopy (SEM), cathodoluminescence (CL), X-ray diffraction (XRD), particle size and sorting, porosity and permeability data from Upper Paleozoic tight sandstone samples, combined with insights into depositional environments, burial history, and chemical reaction processes, this study clarifies the characteristics of tight sandstone reservoirs, reveals the key controlling factors of reservoir quality, confirms the differential evolutionary mechanisms of tight sandstone of different formations, reconstructs the diagenetic sequence, and constructs an evolution model of reservoir minerals and porosity. The research results indicate depositional processes laid the foundation for the original reservoir properties. Sandstones deposited in tidal flat and deltaic environments exhibit superior initial reservoir qualities. Compaction is a critical factor leading to the decline in reservoir quality across all formations. However, rigid particles such as quartz can partially mitigate the pore reduction caused by compaction. Early diagenetic carbonate cementation reduces reservoir quality by occupying primary pores and hindering the generation of secondary porosity induced by acidic fluids, while later-formed carbonate further densifies the sandstone by filling secondary intragranular pores. Clay mineral cements diminish reservoir porosity and permeability by filling intergranular and intragranular pores. The Shanxi and Taiyuan Formations display relatively poorer reservoir quality due to intense illitization. Overall, the reservoir quality of Benxi Formation is the best, followed by Xiashihezi Formation, with the Taiyuan and Shanxi Formations exhibiting comparatively lower qualities. Full article

The pore-throat structure of the extremely low-permeability sandstone reservoir in the Huachi area of the Ordos Basin is complex and highly heterogeneous. Currently, there are issues such as unclear understanding of the micro-pore-throat structural characteristics, primary controlling factors of reservoir quality, and classification boundaries of the reservoir in the study area, which seriously restricts the exploration and development effectiveness of the reservoir in this region. It is necessary to use a combination of various analytical techniques to comprehensively characterize the pore-throat structure and establish reservoir classification evaluation standards in order to better understand the reservoir. This study employs a suite of analytical and testing techniques, including cast thin sections (CTS), scanning electron microscopy (SEM), cathodoluminescence (CL), X-ray diffraction (XRD), as well as high-pressure mercury injection (HPMI) and constant-rate mercury injection (CRMI), and applies fractal theory for analysis. The research findings indicate that the extremely low-permeability sandstone reservoir of the Chang 3 section primarily consists of arkose and a minor amount of lithic arkose. The types of pore-throat are diverse, with intergranular pores, feldspar dissolution pores, and clay interstitial pores and microcracks being the most prevalent. The throat types are predominantly sheet-type, followed by pore shrinkage-type and tubular throats. The pore-throat network of low-permeability sandstone is primarily composed of nanopores (pore-throat radius r < 0.01 μm), micropores (0.01 < r < 0.1 μm), mesopores (0.1 < r < 1.0 μm), and macropores (r > 1.0 μm). The complexity of the reservoir pore-throat structure was quantitatively characterized by fractal theory. Nanopores do not exhibit ideal fractal characteristics. By splicing high-pressure mercury injection and constant-rate mercury injection at a pore-throat radius of 0.12 μm, a more detailed characterization of the full pore-throat size distribution can be achieved. The average fractal dimensions for micropores (Dh2), mesopores (Dc3), and macropores (Dc4) are 2.43, 2.75, and 2.95, respectively. This indicates that the larger the pore-throat size, the rougher the surface, and the more complex the structure. The degree of development and surface roughness of large pores significantly influence the heterogeneity and permeability of the reservoir in the study area. Dh2, Dc3, and Dc4 are primarily controlled by a combination of pore-throat structural parameters, sedimentary processes, and diagenetic processes. Underwater diversion channels and dissolution are key factors in the formation of effective storage space. Based on sedimentary processes, reservoir space types, pore-throat structural parameters, and the characteristics of mercury injection curves, the study area is divided into three categories. This classification provides a theoretical basis for predicting sweet spots in oil and gas exploration within the study area. Full article

This work investigated the structural response and phase transformation dynamics of silica-bearing cherts subjected to high-temperature processing (up to 1400 °C) and prolonged mechanochemical activation. Through a combination of X-ray diffraction (XRD) with Rietveld refinement, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and transmission electron microscopy (HRTEM), we trace the crystallographic pathways of quartz, moganite, tridymite, and cristobalite under controlled thermal and mechanical stress regimes. The experimental results demonstrated that phase behavior is highly dependent on intrinsic properties such as initial phase composition, impurity presence, and crystallinity. Heating at 1400 °C induced irreversible conversion of quartz, moganite, and tridymite into cristobalite. Samples enriched in cristobalite and tridymite exhibited notable increases in crystallinity, whereas quartz-dominant samples showed either stability or a decline in structural order. Rietveld analyses underscored the critical influence of microstrain and crystallite size on thermal resilience and phase persistence. Thermal profiles revealed by DSC and TGA expose overlapping processes including polymorphic transitions, minor phase dehydration, and redox-driven changes, likely associated with trace components. Mechanochemical processing resulted in partial amorphization and the emergence of phases such as opal and feldspar minerals (microcline, albite, anorthite), interpreted as the product of lattice collapse and subsequent reprecipitation. Heat treatment of chert leads to a progressive rearrangement and recrystallization of its silica phases: quartz collapses around 1000 °C before recovering, tridymite emerges as an intermediate phase, and cristobalite shows the greatest crystallite size growth and least deformation at 1400 °C. These phase changes serve as markers of high-temperature exposure, guiding the identification of heat-altered lithic artefacts, reconstructing geological and diagenetic histories, and allowing engineers to adjust the thermal expansion of ceramic materials. Mechanochemical results provide new insights into the physicochemical evolution of metastable silica systems and offer valuable implications for the design and thermal conditioning of silica-based functional materials used in high-temperature ceramics, glasses, and refractory applications. From a geoarchaeological standpoint, the mechanochemically treated material could simulate natural weathering of prehistoric chert tools, providing insights into diagenetic pathways and lithic degradation processes. Full article