Search Results (16)

Surgical ASTM F139 stainless steel is used for temporary fixtures in the biomedical field. Tribocorrosion is a major concern in this application. The aim of the present work was to study the interplay between tribocorrosion behavior and the surface chemistry of the ASTM F139 stainless steel in phosphate-buffered saline solution (PBS). Sliding wear tests were conducted against alumina balls at different electrochemical potentials: open circuit potential (OCP), cathodic potential (−100 mV versus the OCP), and anodic potentials (+200 mV_Ag/AgCl and +700 mV_Ag/AgCl). The normal load was 20 N. The wear volume was estimated based on micrographs obtained from the wear tracks using confocal laser scanning microscopy. Moreover, the wear tracks were also examined by scanning electron microscopy (SEM). The surface chemistry of the ASTM F139 specimens was analyzed by X-ray photoelectron spectroscopy (XPS). The wear volume was dependent on the electrochemical potential, being maximized at +700 mVAg/AgCl. Delamination areas and grooves were observed in the wear tracks. Detailed assessment of the surface chemistry inside the wear tracks allowed identification of the main chemical species and their relative quantities, thus enabling correlation of the passive film composition with the observed tribocorrosion behavior. Full article

In this paper, the authors investigated the impact of DLC coatings doped with tungsten (a-C:H:W) coatings obtained using plasma-assisted physical vapor deposition (PVD) on the properties of the 100Cr6 steel. The results of the 100Cr6 steel specimens with and without the coating were compared. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis were used to observe the morphology of the coating surfaces and cross-sections and identify the elements in the coating composition. The contact angle of the investigated surfaces was measured with a tensiometer. Additionally, the effect of the coatings on the tribological properties of lubricated friction pairs was evaluated. Friction tests were performed on a ball-on-disc tribometer under lubrication with cutting fluid. The surface texture of the samples before and after the tribological tests was measured using a confocal profilometer. The results obtained from the tests and analysis allow for the conclusion that the use of DLC coatings a-C:H:W increases the hardness of 100Cr6 steel by three times. The values of the contact angles were indicative of surface hydrophilic characteristics. The tungsten-doped diamond-like coating under friction conditions reduced the coefficient of friction and wear. DLC coatings a-C:H:W lubricated with the cutting fluid improve the mechanical and tribological properties of 100Cr6 steel sliding surfaces under friction. Full article

This paper evaluates surface roughness effects on the properties of a-C:H:Si coatings obtained using plasma-assisted chemical vapor deposition (PACVD). Prior to coating deposition, the surfaces of the samples were subjected to grinding (Ra = 0.25) and then polishing (Ra = 0.05) or sandblasting (Ra = 1.41). Microscopic observations, measurements of thickness, wettability, surface topography, and tribological tests were used to characterize the substrate. The coating microstructure, thickness, and chemical content were investigated using scanning electron microscopy with energy dispersive spectroscopy (EDS). The geometric structure of the surface was examined using confocal microscopy before and after tribological tests. Tribological studies used a ball-on-disk sliding configuration in reciprocating motion under dry friction and cutting oil lubrication. The values of the contact angles were indicative of surface hydrophilic characteristics. Compared with the sandblasted surfaces, the adhesion strength of the coatings deposited on the polished surfaces was found to be higher. The coatings contributed to the improvement of friction and wear parameters. Under dry friction, a-C:H:Si coating friction coefficients and linear and volumetric wear on the polished surface were reduced compared with the sandblasted surface, respectively, by 10%, 83%, and 85%. In addition, the lubricant contributed to reducing the friction coefficients of the coating applied to the sandblasted sample compared with the polished sample without the coating by about 94%. Microscopic observations of wear traces allowed the determination of wear mechanisms; in the case of Ti13Nb13Zr, it was tribochemical wear through oxidation, while in the case of coatings, scratching and microcutting dominated. Full article

Metal matrix self-lubricating composites exhibit outstanding performance in various environments, reaching the required properties by modifying the reinforcement–matrix ratio and the production method. The present research investigated the effects on tribological performance and electrical properties of different pressure loads, maintaining pressing time, and sintering temperatures during the production of copper–10 wt% tungsten disulfide (Cu–WS₂) composite via powder metallurgy. Moreover, additional thermo-mechanical treatments were evaluated, namely second pressing and second sintering steps. The density and the hardness of the produced composites were measured, as well as the electrical resistivity, considering sliding electrical contacts as possible employment. The outputs of the wear tests were considered together with the analysis of the wear track via scanning electron microscopy and confocal laser scanning microscopy to understand wear mechanisms. Different production routes were compared in terms of electrical resistivity, wear coefficient, and specific wear rate, calculated by the confocal laser scanning microscopy, and friction coefficient, measured during the wear test. The main results highlighted that the increase in sintering temperature was detrimental to the hardness and tribological properties; higher load and additional pressing step determined a general improvement in the tested properties. Full article

Background: Digitally stained ex vivo confocal laser scanning microscopy (CLSM) scans are a possible alternative to formalin-fixed and paraffin-embedded (FFPE) and hematoxylin-eosin (H&E) stained slides. This study explores the diagnostic accuracy of digitally-stained CLSM scans in comparison to H&E-stained slides in various dermatologic diseases in a real-life setting. Methods: Samples of patients out of one selected dermatologic office were primarily scanned via CLSM; a diagnosis was made afterwards using FFPE- and H&E-stained slides by two experienced dermatopathologists. Primary outcomes were sensitivity and specificity of diagnosis in digitally stained CLSM scans in three separate diagnostic groups. Results: CLSM evaluation of epithelial tumors (n = 132) demonstrated a sensitivity of 64.3%/83.9% and a specificity of 84.2%/71.1%. Diagnosis of melanocytic tumors (n = 86) showed a sensitivity of 19.1%/85.1% and a specificity of 96.3%/66.7%. In the diagnosis of other tumors/cysts and inflammatory dermatoses (n = 42), a sensitivity of 96.4%/96.8% and a specificity of 57.1%/45.5% was reached. Conclusions: This study shows the possibilities and limitations of a broad use of CLSM. Because of a partly low diagnostic accuracy, such an application does not seem to be recommendable at present for every indication. Full article

In this work, we studied single-layer ZrN and CrN coatings, as well as multi-layer ZrN/CrN coatings deposited by the vacuum-arc method on WC-8 wt.% Co substrates. The sliding friction parameters were preset to simulate different operating conditions for coatings, i.e., severe and zero wear regimes. During the tests, the friction coefficient, acoustic emission (AE) and vibration signals were recorded. After testing, the worn surfaces of the samples were studied using confocal laser scanning and scanning electron microscopy, elemental microanalysis and synchrotron XRD. Estimation of vibration accelerations and AE energy turned out to be very effective means of monitoring the wear of coatings, while median AE frequency turned out to be a less informative one. With the increase in the normal load applied on the samples after testing at zero wear regime, the coefficient of friction increased and wear transition to severe wear regime occurred but vibration acceleration decreased. The multi-layer ZrN/CrN coatings demonstrated much higher wear resistance as compared to those of single-layer ZrN and CrN. Full article

(1) Background: The aim of this study was to compare the histopathological features of syndromic and non-syndromic odontogenic keratocysts (OKs) using conventional and Confocal Laser Scanning Microscopy (CLSM) with their biological behaviour. (2) Methods: Data from the medical records of 113 patients with histological diagnosis of (single and/or multiple) OKs were collected. Globally, 213 OKs (120 syndromic and 93 sporadic) were retrieved, and their histological slides were re-evaluated with conventional H&E staining and with autofluorescence on the same slides using CLSM (Nikon Eclipse E600 microscope). (3) Results: Syndromic OKs showed more satellite cysts than sporadic cases, as well as a basophilic layer in the basement membrane, which was absent in sporadic OKs; both were highlighted with CLSM. The basement membrane in syndromic OKs appeared amorphous and fragile, thus possibly being responsible for the epithelial detachment and collapse, with scalloped features. Furthermore, the basal epithelial layers in such cases also showed increased cellularity and proliferative activity. All these histological features may possibly justify their higher tendency to recur. (4) Conclusions: CLSM is useful advanced technology that could help to quickly and easily discriminate between syndromic and non-syndromic OKs and to more accurately predict their biological behaviour in order to set fitter clinico-radiological follow-ups for individual patients. Full article

Upregulation of Vimentin (VIM), alpha-Tubulin (TUB) and Detyrosinated tubulin (GLU) in circulating tumor cells (CTCs) derived from breast cancer patients is related to poor prognosis. In the current study we evaluated for the first time, these cytoskeletal proteins in sixty Non-Small Cell Lung Cancer (NSCLC) patients’ CTCs (33 treatment-naïve and 27 pre-treated). Samples were isolated using the ISET platform and stained with a pancytokeratin (CK)/CD45/TUB, CK/GLU/VIM and CK/programmed death ligand 1 (PD-L1) combination of antibodies. Subsequently, slides were analyzed using confocal laser scanning microscopy. CTCs were detected in 86.7% of the patients. CTCs with TUB expression were identified in 65.4% (34/52) of the CK (+)-patients. GLU, VIM and PD-L1 were also evaluated. The frequency of the observed phenotypes was as follow: (CK+/GLU−/VIM−): 35.2%, (CK+/GLU+/VIM+): 63.0%, (CK+/GLU+/VIM−): 16.7%, (CK+/GLU−/VIM+): 72.2%, (CK+/PD-L1−): 75% and (CK+/PD-L1+): 55%. The OS was significantly decreased in patients with high GLU (3.8 vs. 7.9 months; p = 0.018) and/or high VIM (3.2 vs. 7.1 months; p = 0.029) expression in their CTCs. PD-L1 was also related to OS (3.4 vs. 7.21 months; p = 0.035). Moreover, TUB-high and TUB-low expression in CTCs inversely influenced patients’ OS as independent prognostic factors (p = 0.041 and p = 0.009). The current study revealed that TUB, GLU, VIM and PD-L1 were overexpressed in CTCs from NSCLC patients. Furthermore, the presence of GLU, VIM-positive and PD-L1 in CTCs is potentially related to patients’ outcomes. Full article

Image classification with convolutional neural networks (CNN) offers an unprecedented opportunity to medical imaging. Regulatory agencies in the USA and Europe have already cleared numerous deep learning/machine learning based medical devices and algorithms. While the field of radiology is on the forefront of artificial intelligence (AI) revolution, conventional pathology, which commonly relies on examination of tissue samples on a glass slide, is falling behind in leveraging this technology. On the other hand, ex vivo confocal laser scanning microscopy (ex vivo CLSM), owing to its digital workflow features, has a high potential to benefit from integrating AI tools into the assessment and decision-making process. Aim of this work was to explore a preliminary application of CNN in digitally stained ex vivo CLSM images of cutaneous squamous cell carcinoma (cSCC) for automated detection of tumor tissue. Thirty-four freshly excised tissue samples were prospectively collected and examined immediately after resection. After the histologically confirmed ex vivo CLSM diagnosis, the tumor tissue was annotated for segmentation by experts, in order to train the MobileNet CNN. The model was then trained and evaluated using cross validation. The overall sensitivity and specificity of the deep neural network for detecting cSCC and tumor free areas on ex vivo CLSM slides compared to expert evaluation were 0.76 and 0.91, respectively. The area under the ROC curve was equal to 0.90 and the area under the precision-recall curve was 0.85. The results demonstrate a high potential of deep learning models to detect cSCC regions on digitally stained ex vivo CLSM slides and to distinguish them from tumor-free skin. Full article

In this study, acrylonitrile butadiene styrene (ABS) and graphite powder—a solid lubricant—were filled and characterized for friction and wear responses. The fused deposition modeling (FDM) technique was utilized to synthesize ABS–graphite composites. A twin-screw extrusion approach was employed to create the composite filament of graphite–ABS that is suitable for the FDM process. Three graphite particle ratios ranging from 0% to 5% were explored in the ABS matrix. The wear and friction properties of ABS composites were examined using a pin on disc tribometer at varied sliding velocities and weights. As a result of the graphite addition in the ABS matrix, weight losses for FDM components as well as a decreased coefficient of friction were demonstrated. Furthermore, as the graphite weight percentage in the ABS matrix grows the value of friction and wear loss decreases. The wear mechanisms in graphite filled ABS composites and ABS were extensively examined using scanning electron microscopy and confocal microscopy. Full article

The aim of the present study was to evaluate the in vivo bone response to an additively manufactured zirconia surface compared to osseointegration into titanium (Ti) surfaces. Scanning electron microscopy, confocal laser scanning microscopy, and electron spectroscopy for chemical analysis were performed to assess the surface characteristics of implant specimens. For the in vivo evaluation, eight Ti implants and eight 3D-printed zirconia implants were used. The surface of four Ti implants was sandblasted, large-grit, and acid-etched (Ti-SLA group), while those of the other four Ti implants were left untreated (Ti-turned group). The zirconia implants had no further surface modification. Implants were placed into the tibiae of four rabbits; two received the Ti-SLA and zirconia implants and the other two received Ti-turned and zirconia implants. The experimental animals were sacrificed after four weeks of surgery, and the undecalcified microscopic slides were prepared. The bone–implant interface was analyzed by histomorphometry to evaluate the bone response. The degree of surface roughness showed that Ti-SLA was the highest, followed by zirconia and Ti-turned surfaces. The 3D-printed zirconia surface showed similar bone-to-implant contact to the Ti-turned surface, and Ti-SLA had the most bone-to-implant contact. The additively manufactured zirconia implant surface is biocompatible with respect to osseointegration compared to the commercially pure Ti surface. Full article

In cold rolling, a textured roll can be used to imprint a desired surface topography onto the sheet during rolling. This work proposes the use of diamond-like carbon (DLC) coatings to protect the surface topography of the rolls in replacement of the carcinogenic hard chrome. For that, hydrogenated amorphous carbon (a-C:H) was deposited on plasma nitrided tool steel, both for ground and textured specimens. Changes in surface topography due to DLC coating were assessed using a confocal microscope. Coating adhesion was evaluated using the method VDI 3198. The specimens were characterized using X-ray diffraction (XRD), microhardness test and scanning electron microscopy (SEM). The coating was characterized using Raman spectroscopy (RS) and X-ray photoelectron spectroscopy (XPS). The results showed a soft multilayer coating consisting of a plasma nitrided layer for load support, a Si-rich interlayer to improve adhesion and an a-C:H top layer. DLC deposition reduced the roughness of the textured specimens. The coating resulted in relatively stable friction and good durability, with small damage and negligible wear even under dry sliding. Full article

Laser-induced periodic surface structures (LIPSS, ripples) with ~500–700 nm period were produced on titanium alloy (Ti6Al4V) surfaces upon scan processing in air by a Ti:sapphire femtosecond laser. The tribological performance of the surfaces were qualified in linear reciprocating sliding tribological tests against balls made of different materials using different oil-based lubricants. The corresponding wear tracks were characterized by optical and scanning electron microscopy and confocal profilometry. Extending our previous work, we studied the admixture of the additive 2-ethylhexyl-zinc-dithiophosphate to a base oil containing only anti-oxidants and temperature stabilizers. The presence of this additive along with the variation of the chemical composition of the counterbodies allows us to explore the synergy of the additive with the laser-oxidized nanostructures. Full article

According to the stoichiometric ratios of Mo-10Si-7B, Mo-12Si-8.5B, Mo-14Si-9.8B, and Mo-25Si-8.5B, some new Mo-Si-B alloys doped with 0.3 wt % lanthanum (III) oxide (La₂O₃) were prepared via liquid-liquid (L-L) doping, mechanical alloying (MA), and hot-pressing (HP) sintering technology. The phase-composition and microstructure were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). The worn surfaces of the plate specimens were studied by confocal laser scanning microscopy (CLSM). Then, the tribological properties of Mo-Si-B alloy doped with sliding plate specimens of 0.3 wt % La₂O₃ were investigated against the Si₃N₄ ball specimens. The friction coefficients of Mo-Si-B alloys decreased and the wear rates of the alloys increased with test load. The high-temperature friction and wear behavior of Mo-Si-B alloy are related to the surface-oxidation and contact-deformation of the alloy at a high temperature. The low friction coefficients and the reduced wear rates are thought to be due to the formation of low friction MoO₃ films. MoO₃ changed the contact state of the friction pairs and behaved as lubricating films. Full article

MicroRNA-21 (miR-21) is upregulated in many cancers including colon cancers and is a prognostic indicator of recurrence and poor prognosis. In colon cancers, miR-21 is highly expressed in stromal fibroblastic cells and more weakly in a subset of cancer cells, particularly budding cancer cells. Exploration of the expression of inflammatory markers in colon cancers revealed tumor necrosis factor alpha (TNF-α) mRNA expression at the invasive front of colon cancers. Surprisingly, a majority of the TNF-α mRNA expressing cells were found to be cancer cells and not inflammatory cells. Because miR-21 is positively involved in cell survival and TNF-α promotes necrosis, we found it interesting to analyze the presence of miR-21 in areas of TNF-α mRNA expression at the invasive front of colon cancers. For this purpose, we developed an automated procedure for the co-staining of miR-21, TNF-α mRNA and the cancer cell marker cytokeratin based on analysis of frozen colon cancer tissue samples (n = 4) with evident cancer cell budding. In all four cases, TNF-α mRNA was seen in a small subset of cancer cells at the invasive front. Evaluation of miR-21 and TNF-α mRNA expression was performed on digital slides obtained by confocal slide scanning microscopy. Both co-expression and lack of co-expression with miR-21 in the budding cancer cells was noted, suggesting non-correlated expression. miR-21 was more often seen in cancer cells than TNF-α mRNA. In conclusion, we report that miR-21 is not linked to expression of the pro-inflammatory cytokine TNF-α mRNA, but that miR-21 and TNF-α both take part in the cancer expansion at the invasive front of colon cancers. We hypothesize that miR-21 may protect both fibroblasts and cancer cells from cell death directed by TNF-α paracrine and autocrine activity. Full article