Search Results (14)

Additive manufacturing processes are among the most innovative manufacturing processes of this century. Powder-based direct metal deposition (DMD) is one of these processes. In the DMD process, local shielding takes place via the powder nozzle. The process is therefore critical for oxidation, especially for materials with an affinity for oxidation such as titanium, aluminum and their alloys. In order to study the oxidation behavior in more detail, the present gas dynamics must be further understood. Wirth and Wegener have made a first approach with their gas flow simulation. In this study, a measurement method for spatial oxygen concentration determination is presented. It can be shown that the spatial oxygen concentration follows the nozzle geometry. Furthermore, the coaxial nozzle is superior to the three-jet nozzle with respect to a low oxygen concentration from a carrier gas to shielding gas volume flow ratio of equal to or greater than 0.4. Finally, it can be shown that the use of a shielding gas chamber eliminates the optimization of the gas flow settings. Full article

Laser-directed energy deposition (LDED) is a promising technology for coating, repairing, and building near-net-shape 3D structures. However, the processing of copper alloys, specifically, has presented a significant challenge due to their low laser absorptivity at the 1060 nm laser wavelength and high thermal conductivity. This study undertook a methodical examination by employing a 2 kW disk laser, operating at a wavelength of 1064 nm, and a coaxial nozzle head to comprehensively examine the processability of the highly conductive CuCrZr alloy for expanding the range of materials that can be successfully processed using LDED. The investigation focuses not only on optimizing the input process parameters that are the laser power, scanning speed, powder feed rate, and overlap ratio, but also on planning the toolpath trajectory, as these factors were found to exert a substantial influence on processability, geometrical accuracy, and the occurrence of defects such as lack of fusion. The optimal toolpath trajectory discovered involved implementing a zigzag strategy combined with a 90° rotation of the scanning direction. Additionally, a start point rotation was considered between each layer to even out the deposition of the layers. Moreover, a contour with a radial path at the corners was introduced to enhance the overall trajectory. Based on the hierarchal experimental study, the appropriate ranges for the key process parameters that leads to 99.99% relative density have been identified. They were found to be from 1100 up to 2000 W for the laser power (P), and from 0.003 up to 0.016 g/mm for the amount of powder that is fed to the melt pool distance (F/V). Regarding the influence of process parameters on the microstructure of the samples with equal deposition height, it was observed that varying combinations of process parameters within the optimal processing window resulted in variations in grain size ranging from 105 to 215 µm. Full article

In this work, a semi-continuous functionally graded material (FGM) between an austenitic and a super duplex stainless steel was obtained. These materials are of great interest for the chemical, offshore, and oil and gas sectors since the austenitic stainless steel type 316L is common (and not so expensive) and super duplex stainless steels have better mechanical and corrosion resistance but are more expensive and complex in their microstructural phases formation and the obtention of the balance between their main phases. Using directed energy deposition, it was possible to efficiently combine two powders of different chemical compositions by automated mixing prior to their delivery into the nozzle, coaxially to the laser beam for melting. A dense material via additive manufacturing was obtained, with minimum defectology and with a semi-continuous and controlled chemical compositional gradient in the manufactured part. The evolution of ferrite formation has been verified and the phase fraction measured. The resulting microstructure, austenite/ferrite ratio, and hardness variations were evaluated, starting from 100% austenitic stainless-steel composition and with variants of 5% in wt.% until achieving 100% of super duplex steel at the end of the part. Finally, the correlation between the increase in hardness of the FGM with the increase in the ferrite phase area fraction was verified. Full article

Laser direct metal deposition (LDMD) enables not only the preparation of high-performance coatings on the surfaces of low-property materials but also the three-dimensional direct manufacturing and re-manufacturing of parts. In the LDMD process, the spatial coupling characteristics of the powder flow and the laser beam are the key factors affecting the forming quality of the cladding layer. Based on the gas–solid two-phase flow theory, a numerical model of coaxial powder feeding was established by CFD. The powder flow characteristics of the lower part of the nozzle, the powder particle motion trajectory, and the optical-powder spatial coupling morphology and law were studied, and the relationship between the powder flow morphology, laser beam, and powder utilization was explored. On this basis, the law between the optical-powder coupling characteristics and the geometric characteristics of the cladding layer is discussed in conjunction with LDMD experiments. The results show that the powder concentration scalar located in the focal plane of the laser beam can be used to visualize the optical-powder coupling morphology. When the powder feeding speed exceeds the loading capacity of the carrier gas flow, the powder concentration in the center of the spot and the powder utilization rate decrease. When the carrier gas flow rate is 4.0 L/min and the powder feeding rate is 4.0 g/min, the best utilization rate achieved is 81.4%. In addition, the H (height) of the cladding layer is more sensitive to changes in the powder concentration than the W (width). These findings provide new ideas for nozzle structure design and the optimization of LDMD parameters. Full article

Laser metal deposition with coaxial wire feeding is a directed energy deposition process in which a metal wire is fed to a laser-induced melt pool. Oxidation occurring during the process is a major challenge as it significantly influences the mechanical properties of the produced part. Therefore, an inert gas atmosphere is required in the high temperature process zone, whereby local shielding offers significant cost advantages over an inert gas chamber. In this work, a novel local shielding gas nozzle was developed based on basic methods of fluid mechanics. A gas flow-optimized prototype incorporating internal cooling channels was additively manufactured by laser-powder bed fusion and tested for its effectiveness via deposition experiments. Using the developed local shielding gas concept, an unwanted mixing with the atmosphere due to turbulence was avoided and an oxide-free deposition was achieved when processing a stainless steel ER316LSi wire. Furthermore, the effects of the shielding gas flow rate were investigated, where a negative correlation with the melt pool temperature as well as the weld bead width was demonstrated. Finally, a solid cuboid was successfully built up without oxide inclusions. Overheating of the nozzle due to reflected laser radiation could be avoided by the internal cooling system. The concept, which can be applied to most commercially available coaxial wire deposition heads, represents an important step for the economical application of laser metal deposition. Full article

In the process of laser-based direct energy deposition, the particle concentration distribution and geometric characteristics of powder flow play an important role in laser–powder interaction and powder utilization, and they affect the forming quality and accuracy. In the current study, based on the geometry information of a powder nozzle and the divergence angles of a powder jet at the nozzle outlet, the geometric profile of a powder stream is analyzed. A set of formulas for calculating the geometric characteristics of the powder stream is derived based on an analytic geometry method. The influence of each parameter on the geometric characteristics of the powder stream is further studied using single-factor and sensitivity analyses. Validation is performed by comparing the results from the presented analytical expressions with those from experiments and/or simulations in published papers. The analytical formulas provided in this paper are simple and practical, providing a theoretical foundation for the control of powder flow and related processes in the forming process. Full article

Coaxial powder feeding technology in the field of metal additive manufacturing is booming. In this paper, a new laser cladding nozzle with powder feeding channels of inner and outer rings is designed. The nozzle works with a new kind of laser, which is a new heat source with an inner beam and outer beams. The water-cooling channels are simulated in Ansys Workbench. The simulation results present the temperature distribution of the working nozzle and the velocity of the cooling water. The thermal dilation of the nozzle in the working environment is also simulated. The results show that the loop water cooling channel could effectively reduce the high temperature of the nozzle down to about 200 °C. In addition, it could well restrain the thermal deformation of the nozzle lower to 0.35 mm. The equivalent stress of most parts is controlled under 360 MPa. Then, the powder flows of the inner and outer rings of the multiple powder feeding channels are simulated in Ansys Fluent. The convergence effect of the powder flow could be assumed and some significant parameters, such as the velocity, are acquired. The results present that these multiple powder feeding channels could realize the generation and removal of removable supports of workpieces with highly complex shapes and achieve a large processing range and good processing efficiency. The velocity of the powder flow at the outlet is elevated to about 5 mm/s. Then, the thermal cladding states under the new laser heat source of the powder are simulated in Workbench. The temperature of the melting process and the thermal deformation and the equivalent stress/strain of the additive parts are obtained in the emulation. The results emerge that the powder melting range and the ascending temperature of the melting pool are improved with this effect. The greatest temperature of the melting pool is about 2900 °C in the machining process, and the maximum thermal equivalent stress is 1.1407 × 10¹⁰ Pa. Full article

A 3D model was established to accurately simulate the internal and external powder stream characteristics of the coaxial discrete three-beam nozzle for laser metal deposition. A k-ε turbulence model was applied in the gas flow phase, and powder flow was coupled to the gas flow by a Euler-Lagrange approach as a discrete phase model. The simulated powder stream morphology was in good agreement with the experimental results of CCD and high-speed camera imaging. The simulation results showed that the length, diameter and shrinkage angle of the powder passage in the nozzle have different effects on the velocity and convergence characteristics of the powder stream. The influence of different particle size distribution and the inner laser shielding gas on the powder stream were also discussed in this study. By analyzing the powder stream caused by different incident directions of powder passage, and the collision process between powder and the inner wall, the basic principle of controlling powder stream convergence was obtained. Full article

The Laser Metal Deposition (LMD) process is an additive manufacturing method, which generates 3D structures through the interaction of a laser beam and a gas/powder stream. The stream diameter, surface density and focal plan position affect the size, efficiency and regularity of the deposit tracks. Therefore, a precise knowledge of the gas/powder streams characteristics is essential to control the process and improve its reliability and reproducibly for industrial applications. This paper proposes multiple experimental techniques, such as gas pressure measurement, optical and weighting methods, to analyze the gas and particle velocity, the powder stream diameter, its focal plan position and density. This was carried out for three nozzle designs and multiple gas and powder flow rates conditions. The results reveal that (1) the particle stream follows a Gaussian distribution while the gas velocity field is closer to a top hat one; (2) axial, carrier and shaping gas flow significantly impact the powder stream’s focal plan position; (3) only shaping gas, powder flow rates and nozzle design impact the powder stream diameter. 2D axisymmetric models of the gas and powder streams with RANS turbulent model are then performed on each of the three nozzles and highlight good agreements with experimental results but an over-estimation of the gas velocity by pressure measurements. Full article

The consequences of gravity and the nozzle inclination angle in the powder-fed Directed Energy Deposition (DED) process were examined in this study. We also sought to define guidelines and manufacturing strategies, depending on the DED system configuration and the nozzle type. To do so, two nozzle types were used: a continuous coaxial nozzle with a slit of 0.5 mm and a four-stream discrete coaxial nozzle. Although the main effects of the configurations and the nozzles are well-known, their effects on the clad characteristics and the deposition strategy are as yet unclear. In this paper, measurements of a single clad and the effects of different deposition strategies on cladding applications and inclined walls are presented, and the consequences for manufacturing processes are discussed. Based on a complete study of a single clad, working vertically, five different tilted deposition strategies were applied: three to a single clad and two to an inclined wall. The results for both the single clad and the inclined wall reflect a pattern of changes to height, width, area, and efficiency, at both small and large nozzle angles and deposition strategies. The inclined wall presents a maximum horizontal displacement that can be reached per layer, without geometrical distortions. The amount of material per layer has to be adapted to this limitation. Full article

Extreme high-speed laser material deposition, known by its German acronym EHLA, is a new variant of laser material deposition (LMD) with powdered additives. This variant’s process control is unlike that of LMD, where the powder melts as it contacts the melt pool. In the EHLA process, the laser beam melts the powder above the surface of the substrate to deliver a liquid to the melt pool. At a given intensity distribution in a laser beam, the heating of powder particles in the beam path depends largely on the three-dimensional powder particle density distribution (PDD) and the relative position within the laser beam caustic. As a key element of a comprehensive numerical process model for EHLA, this paper presents a statistical/numerical model of the powder-gas jet, as previously published in Experimentelle und modelltheoretische Untersuchungen zum Extremen Hochgeschwindigkeits-Laserauftragschweißen. The powder-gas jet is characterized experimentally and described with a mathematical model. This serves to map the PDD of the powder-gas flow—and particularly the particle trajectories for different grain fractions—as well as the powder mass flows and carrier and inert gas settings, to a theoretical model. The result is a numerical description of the particle trajectories that takes into account the measured particle size distribution with calculations made on the assumption of a constant particle velocity and linear trajectories of the particles. Full article

Laser Cladding is one of the leading processes within Additive Manufacturing technologies, which has concentrated a considerable amount of effort on its development. In regard to the latter, the current study aims to summarize the influence of the most relevant process parameters in the laser cladding processing of single and compound volumes (solid forms) made from AISI 316L stainless steel powders and using a coaxial nozzle for their deposition. Process speed, applied laser power and powder flow are considered to be the main variables affecting the laser cladding in single clads, whereas overlap percentage and overlapping strategy also become relevant when dealing with multiple clads. By setting appropriate values for each process parameter, the main goal of this paper is to develop a processing window in which a good metallurgical bond between the delivered powder and the substrate is obtained, trying simultaneously to maintain processing times at their lowest value possible. Conventional metallography techniques were performed on the cross sections of the laser tracks to measure the effective dimensions of clads, height and width, as well as the resulting dilution value. Besides the influence of the overlap between contiguous clads and layers, physical defects such as porosity and cracks were also evaluated. Optimum process parameters to maximize productivity were defined as 13 mm/s, 2500 W, 30% of overlap and a 25 g/min powder feed rate. Full article

For the purpose of improving the productivity of laser metal deposition (LMD), the focus of current research is set on increasing the deposition rate, in order to develop high-deposition-rate LMD (HDR-LMD). The presented work studies the effects of the powder stream on HDR-LMD with Inconel 718. Experiments have been designed and conducted by using different powder feeding nozzles—a three-jet and a coaxial powder feeding nozzle—since the powder stream is mainly determined by the geometry of the powder feeding nozzle. After the deposition trials, metallographic analysis of the samples has been performed. The laser intensity distribution (LID) and the powder stream intensity distribution (PID) have been characterized, based on which the processes have been simulated. Finally, for verifying and correcting the used models for the simulation, the simulated results have been compared with the experimental results. Through the conducted work, suitable boundary conditions for simulating the process with different powder streams has been determined, and the effects of the powder stream on the process have also been determined. For a LMD process with a three-jet nozzle a substantial part of the powder particles that hit the melt pool surface are rebounded; for a LMD process with a coaxial nozzle almost all the particles are caught in the melt pool. This is due to the different particle velocities achieved with the two different nozzles. Moreover, the powder stream affects the heat exchange between the heated particles and the melt pool: a surface boundary condition applies for a powder stream with lower particle velocities, in the experiment provided by a three-jet nozzle, and a volumetric boundary condition applies for a powder stream with higher particle velocities, provided by a coaxial nozzle. Full article

Laser cladding process was performed on a commercial Ti-6Al-4V (α + β) titanium alloy by means of tungsten carbide-nickel based alloy powder blend. Nd:YAG laser with a 2.2-KW continuous wave was used with coaxial jet nozzle coupled with a standard powder feeding system. Four-track deposition of a blended powder consisting of 60 wt % tungsten carbide (WC) and 40 wt % NiCrBSi was successfully made on the alloy. The high content of the hard WC particles is intended to enhance the abrasion resistance of the titanium alloy. The goal was to create a uniform distribution of hard WC particles that is crack-free and nonporous to enhance the wear resistance of such alloy. This was achieved by changing the laser cladding parameters to reach the optimum conditions for favorable mechanical properties. The laser cladding samples were subjected to thorough microstructure examinations, microhardness and abrasion tests. Phase identification was obtained by X-ray diffraction (XRD). The obtained results revealed that the best clad layers were achieved at a specific heat input value of 59.5 J·mm⁻². An increase by more than three folds in the microhardness values of the clad layers was achieved and the wear resistance was improved by values reaching 400 times. Full article