Search Results (22)

The high yttria content of a stabilized zirconia (YSZ) (38 wt% Y₂O₃) coating was deposited by atmospheric plasma spraying (APS) from Metco 207 powders on an Inconel 718 (Ni-based superalloy) substrate. As a metal coating connection, a layer of cermet powder (Ni-20% Al—410NS) was used before the ceramic layer deposition. The electro-chemical corrosion resistance of these materials was tested using Inconel cylinders with a diameter of 10 mm and a thickness of 1 mm, with and without the ceramic layer. Linear and cyclic measurements were obtained in H₂SO₄ electrolyte media at pH = 2. Electro-impedance spectroscopy (EIS) experiments were performed on the sample covered with the ceramic layer to evaluate the interface behavior. Scanning electron microscopy (SEM), along with equipment to determine chemical composition, and an energy dispersive spectrometry (EDS) detector were used to characterize the material surface before and after corrosion tests. It was observed that the corrosion resistance of Inconel was influenced by the bonding layer and the ceramic coating. Full article

The use of metal-coated ceramic powders not only effectively enhances the wettability of the metal–ceramic interface but also promotes a more uniform microstructure in Ti(C,N)-based cermets, which is advantageous for improving their mechanical properties. In this study, ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders were synthesized via the spray-drying-in-situ carbothermal reduction method. Subsequently, Ti(C,N)-based cermets were effectively fabricated using the as-prepared ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. The impact of reaction temperature, heating rate, and isothermal time on the phase and microstructure of prepared powders was analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Additionally, the microstructure of the as-sintered cermets was experimentally investigated. The findings reveal that the complete reduction of Co and Ni metal salts, pre-coated on the surface of (Ti,W,Mo,Ta)(C,N) particles, can be achieved through rapid heating (10 °C/min) in a specific temperature range (600–1000 °C) with an isothermal time of 3 h at a lower reduction temperature (1000 °C). The synthesized powders have only two phases: the (Ti,W,Mo,Ta)(C,N) phase and Co/Ni phase, and no other heterogeneous phases were observed with an oxygen content of 0.261 wt.%. Notably, the conventional core–rim structure was not dominant in the cermets obtained from the prepared Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. Moreover, the heterogeneous segregation effect of the Co/Ni coating on the ultrafine powder particles resulted in a finer microstructure than the traditional cermets with the same composition. However, the grain size is mainly in the range of 0.5–0.8 μm. The weaker residual stresses at the core and rim interfaces and the finer particle distributions could theoretically enhance the toughness of Ti(C,N)-based cermets, simultaneously. Full article

Ti(C,N)-based cermet is a kind of composite material composed of a metal binder phase and a Ti(C,N)-hard phase, which is widely used in the fields of cutting machining and wear-resistant parts due to its high hardness, good toughness, wear resistance, and chemical stability. In recent years, the research on the replacement of traditional Ni, Co, and Fe binder phases by novel binder phases such as intermetallic compounds and high-entropy alloys has made remarkable progress, which significantly improves the mechanical properties, wear resistance, corrosion resistance, and high-temperature oxidation resistance of Ti(C,N)-based cermets. This paper reviews the latest research results, summarizes the mechanism of the new binder to improve the performance of metal–ceramics, and looks forward to the future research directions. Full article

This study demonstrated a silver (Ag) and samarium-doped ceria (SDC) mixed ceramic and metal composite (i.e., cermet) as a cathode for low-temperature solid oxide fuel cells (LT-SOFCs). Introducing the Ag-SDC cermet cathode for LT-SOFCs revealed that the ratio between Ag and SDC, which is a crucial factor for catalytic reactions, can be tuned by the co-sputtering process, resulting in enhanced triple phase boundary (TPB) density in the nanostructure. Ag-SDC cermet not only successfully performed as a cathode to increase the performance of LT-SOFCs by decreasing polarization resistance but also exceeded the catalytic activity of platinum (Pt) due to the improved oxygen reduction reaction (ORR). It was also found that less than half of Ag content was effective to increase TPB density, preventing oxidation of the Ag surface as well. Full article

Pioneering studies on the additive manufacturing of a cermet heterogeneous material using SiC ceramic fiber were carried out. Unique studies of the damage staging (cratering) and the transition to the destruction of the formed material during high-speed impact created with the help of an electrodynamic mass accelerator have been carried out. It has been shown that the use of ceramic fiber in a metal matrix reduces the impact crater depth by 22% compared to material with ceramic particles. For the first time, the phase composition of the resulting composite was studied using synchrotron radiation. It was shown that, as a result of laser exposure, silicon carbide SiC is dissolved in the titanium matrix with the formation of secondary compounds of the TiC and Ti5Si3C types. It has been established that the use of SiC ceramic fibers leads to their better dissolution, in contrast to the use of SiC ceramic particles, with the formation of secondary phase compounds, and to an increase in mechanical characteristics. Full article

Self-propagating high-temperature synthesis (SHS) is a good way to prepare ZrB₂-ZrC/metal cermet composites. In this work, ZrB₂-ZrC/Ni cermet composites with various Ni contents were successfully fabricated by SHS using the Ni-Zr-B₄C system. The effects of Ni content and particle size of the B₄C powder on the SHS reaction were investigated. The results indicated that with an increase in Ni content, the adiabatic temperature, maximum combustion temperature, ignition delay time, and ceramic particle size in the product all showed a gradually decreasing trend. The SHS products and the ignition of the SHS reactions were significantly dependent on the B₄C particle size. The formation mechanism of ZrB₂ and ZrC during SHS from the Ni-Zr-B₄C system was proposed based on the combustion wave quenching experiment. Full article

To obtain highly homogeneous cobalt–nickel aluminate spinels with small crystallite sizes, CoNiAl alloy thin films were primarily deposited using Laser-induced Thermionic Vacuum Arc (LTVA) as a versatile method for performing processing of multiple materials, such as alloy/composite thin films, at a nanometric scale. Following thermal annealing in air, the CoNiAl metallic thin films were transformed into ceramic oxidic (Co,Ni)Al₂O₄ with controlled composition and crystallinity suitable for thermal stability and chemical resistance devices. Structural analysis revealed the formation of (Co,Ni)Al₂O₄ from the amorphous CoNiAl alloys. The mean crystallite size of the spinels was around 15 nm. Thermal annealing induces a densification process, increasing the film thickness together with the migration process of the aluminum toward the surface of the samples. The sheet resistance changed drastically from 200–240 Ω/sq to more than 10⁶ Ω/sq, revealing a step-by-step conversion of the metallic character of the thin film to a dielectric oxidic structure. These cermet materials can be used as inert anodes for the solid oxide fuel cells (SOFCs), which require not only high stability with respect to oxidizing gases such as oxygen, but also good electrical conductivity. These combination metal–ceramics are known as bi-layer anodes. By controlling the crystallite size and the interplay between the oxide/metal composite, a balance between stability and electrical conductivity can be achieved. Full article

Cermet is an advanced class of material consisting of a hard ceramic phase along with a metallic binding phase with the combined advantages of both the ceramic and the metal phase. The superior properties of this class of materials are particularly useful in high-temperature, tribological, and machining applications. This review paper seeks to provide a comprehensive overview of the various cermet systems. More specifically, the most commonly used cermet systems based on tungsten carbide (WC), titanium carbide (TiC), titanium carbonitride (TiCN), and aluminum oxide (Al₂O₃) are discussed based on their development, properties, and applications. The effect of different metallic binders and their composition on the tribological and mechanical properties of these cermet systems is elaborated. The most common processing techniques for cermet systems, such as powder metallurgy (PM), reaction synthesis (RS), thermal spray (TS), cold spray (CS), and laser-based additive manufacturing techniques are discussed. The influence of the processing parameters in each case is evaluated. Finally, the applications and challenges of cermet systems are summarized. Full article

Cermet coatings with ceramic and metal characteristics will play an increasingly important role in extending the service life of critical components in harsh service environments. In this paper, CoCrAlTaY-30Al₂O₃ (wt.%) cermet coating was prepared by air plasma spraying technique. The effect of powder feeding rate on the microstructure and mechanical properties of the coating and its high-temperature oxidation behavior was investigated. The results showed that the CoCrAlTaY-30Al₂O₃ spraying powder mainly consisted of Al₅Co₂, α-Al₂O₃, Co, Cr₇C_3, and TaC in five phases. The microstructure of cermet coating was uniform and its porosity was relatively low. The coating was mainly composed of Al₅Co₂, Cr, and Al₂O₃ phases, and the change of powder feeding rate had no obvious effect on the phase composition of the coating. When the powder feeding rate was 32 g/min, the minimum porosity of the coating was (3.68 ± 0.86)%, and the maximum Vickers hardness and binding strength were (664.9 ± 55.9) HV0.3 and (78.6 ± 6.6) MPa, respectively. The oxidation rate constant k_p1 of the coating at 1050 °C was 0.066 mg²∙cm⁻⁴∙h⁻¹, and the fitted curve R² value was 0.99547. In the oxidization initial stages, the alloy elements Co, Al, and Cr in the cermet coating were rapidly oxidized to form CoO, Al₂O₃, and Cr₂O₃. Then Al₂O₃ and Cr₂O₃ reacted with CoO to form Co(Al,Cr)₂O₄ spinel oxides. The θ-Al₂O₃ phase was formed after initial oxidation while the θ-Al₂O₃ phase was completely transformed into α-Al₂O₃ after 200 h. The oxide film mainly contained Co(Cr,Al)₂O₄, Cr₂O₃, and α-Al₂O₃ phases. Full article

Ta/Ti/Ni/ceramic multilayered composites were successfully prepared by combustion synthesis. Laminated composites Ti–Ta–(Ti + 0.65C)–Ni–(Ti + 1.7B)–(Ti + 1.7B)–Ta–Ni-Ti and 3(Ti + 1.7B)–Ta–(5Ti + 3Si)–Ta–(Ti + 1.7B)–Ta–(5Ti + 3Si)–Ta–3(Ti + 1.7B) were combustion synthesized in an Ar atmosphere using (1) metallic foils (Ti, Ta, Ni) and (2) reactive tapes (Ti + 0.65C), (Ti + 1.7B), and (5Ti + 3Si), which, upon combustion, yielded ceramic layers as starting materials. The microstructure, crystal structure, and chemical composition of multilayered composites were characterized by SEM, EDX, and XRD. Their flexural strength was measured at 1100 °C. Upon combustion, Ta foils turned strongly joined with Ti ones due to the development of high temperature in the reactive layers yielding TiC_x and TiB_y. The formation of a liquid phase between metallic foils and reactive tapes and mutual interdiffusion between melted components during combustion favored strong joining between refractory metallic foils. Good joining between metals and ceramics is reached due to the formation of thin interfacial layers in the form of cermets and eutectic solutions. Full article

WC-based hardmetals are employed widely as wear-resistant ceramic–metal composites for tools and wear parts. Raw materials supply, environmental concerns and some limitations of hardmetals have directed efforts toward development of alternative wear-resistant composites–cermets. We present a current state of knowledge in the field of ceramic-rich (≥50 vol%) cermets behavior in abrasion and erosion conditions, which are the dominant types of wear in many industrial applications. Distinction is made between two-body and three-body abrasion, solid-particle erosion, and slurry erosion. Cermets, in particular TiC-, Ti(C,N)- and Cr₃C₂-based composites and hardmetals, are compared for their abrasive and erosive wear performance and mechanism. The review enabled formulation of tribological conditions in which cermets may be comparable or have potential to outperform WC-Co hardmetals. Hardmetals, in general, outperform cermets in abrasion and solid-particle erosion at room and moderate temperatures. However, cermets demonstrate their potential mainly in severe conditions—at elevated temperatures and corrosive (oxidation, electrochemical corrosion) environments. Full article

In recent years, the use of cermets has shown significant growth in the industry due to their interesting features that combine properties of metals and ceramics, and there are different possible types of cermets, depending on their composition. This review focuses on cemented tungsten carbides (WC), and tungsten carbonitrides (WCN), and it is intended to analyze the relationship between chemical composition and processing techniques of these materials, which results in their particular microstructural and mechanical properties. Moreover, the use of cermets as a printing material in additive manufacturing or 3D printing processes has recently emerged as one of the scenarios with the greatest projection, considering that they manufacture parts with greater versatility, lower manufacturing costs, lower raw material expenditure and with advanced designs. Therefore, this review compiled and analyzed scientific papers devoted to the synthesis, properties and uses of cermets of TiC and WC in additive manufacturing processes reported thus far. Full article

This work analyzes the differences found in hard metal coatings produced by two high velocity thermal spray techniques, namely high velocity oxy-fuel (HVOF) and high velocity air-fuel (HVAF). Additionally, the effect of the metallic matrix and ceramic composition and the original carbide grain size on coating properties is compared to the most studied standard reference material sprayed by HVOF, WC-Co. For this evaluation, the physical properties of the coatings, including feedstock characteristics, porosity, thickness, roughness, hardness, and phase composition were investigated. Several characterization methods were used for this purpose: optical microscopy (OM), scanning electronic microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), and X-ray Diffraction (XRD), among others. The final performance (abrasive wear and corrosion resistance) shown by the coatings obtained by these two methodologies was also analyzed. Thus, the abrasive wear resistance was analyzed by the rubber-wheel test, while the corrosion resistance was characterized with electrochemical methods. The characterization results obtained clearly showed that the coatings exhibit different microstructures according to feedstock powder characteristics (carbide grain size and/or composition) and the thermal spray process used for its deposition. Thus, the incorporation of WB to the cermet composition led to a high hardness coating, and the complementary hardness and toughness of the WC-Co coatings justify its better abrasion resistance. The presence of Ni on the metal matrix increases the free corrosion potential of the coating to more noble region. However, the WC-Co coatings show a lower corrosion rate and hence a higher protective performance than the rest of the coatings. Full article

Open-celled ceramic composite foams were prepared from NiO and yttria-stabilized zirconia (YSZ) powders by the polymer sponge replication (Schwartzwalder) technique using the respective aqueous dispersions. Mechanically stable NiO–YSZ foams with an average porosity of 93 vol.% were obtained. After chemical reduction of the NiO phase with hydrogen, cellular Ni–YSZ cermet structures were obtained. They are characterized by an electric conductivity up to 19∙10³ S∙m⁻¹ which can be adjusted by both, the Ni volume fraction, and the sintering/reduction procedure. The NiO–YSZ ceramic foams, as well as the cellular Ni–YSZ cermets prepared therefrom, were characterized with respect to their microstructure by scanning electron microscopy, confocal Raman microscopy and X-ray diffraction with Rietveld analysis. In addition, the compressive strength, the electric conductivity and the thermal conductivity were determined. The collected data were then correlated to the sample microstructure and porosity and were also applied for modelling of the mechanical and electric properties of the bulk Ni–YSZ strut material. Full article

The aim of the research was to disclose the performance of ceramic-metal composites, in particular TiC-based cermets and WC-Co hardmetals, as tool materials for friction stir welding (FSW) of aluminium alloys, stainless steels and copper. The model tests were used to study the wear of tools during cutting of metallic workpiece materials. The primary focus was on the performance and degradation mechanism of tool materials during testing under conditions simulating the FSW process, in particular the welding process temperature. Carbide composites were produced using a common press-and-sinter powder metallurgy technique. The model tests were performed on a universal lathe at the cutting speeds enabling cutting temperatures comparable the temperatures of the FSW of aluminium alloys, stainless steels and pure copper. The wear rate of tools was evaluated as the shortening of the length of the cutting tool nose tip and reaction diffusion tests were performed for better understanding of the diffusion-controlled processes during tool degradation (wear). It was concluded that cermets, in particular TiC-NiMo with 75–80 wt.% TiC, show the highest performance in tests with counterparts from aluminium alloy and austenitic stainless steel. On the other hand, in the model tests with copper workpiece, WC-Co hardmetals, in particular composites with 90–94 wt.% WC, outperform most of TiC-based cermet, including TiC-NiMo. Tools from ceramic-metal composites wear most commonly by mechanisms based on adhesion and diffusion. Full article