Search Results (23)

Fouling, particularly from organic fouling and biofouling, poses a significant challenge in the RO/NF treatment of marginal waters, especially wastewater. Part 1 of this review detailed LMWOC fouling mechanisms. Part 2 focuses on countermeasures and applications. Effective fouling prevention relies on pretreatment, early detection, cleaning, optimized operation, and in situ membrane modification. Accurate fouling prediction is crucial. Preliminary tests using flat-sheet membranes or small-diameter modules are recommended. Currently, no specific fouling index exists for LMWOC fouling. Hydrophobic membranes, such as polyamide, are proposed as alternatives to the standard silt density index (SDI) filter. Once LMWOC fouling potential is assessed, suitable pretreatment methods can be implemented. These include adsorbents, specialized water filters, oxidative decomposition, and antifoulants. In situations where pretreatment is impractical, alternative strategies like high pH operation might be considered. Membrane cleaning becomes necessary upon fouling; however, standard cleaning often fails to fully restore the original flow. Specialized CIP chemicals, including organic solvent-based and oxidative agents, are required. Conversely, LMWOC fouling typically leads to a stabilized flow rate reduction rather than a continuous decline. Aggressive cleaning may be avoided if the resulting operating pressure increase is acceptable. When a significant flow rate drop occurs and LMWOC fouling is suspected, analysis of the fouled membrane is necessary for identification. Standard FT-IR often fails to detect LMWOCs. Solvent extraction followed by GC-MS is required. Pyrolysis GC-MS, which eliminates the extraction step, shows promise. The review concludes by examining how LMWOCs can be strategically utilized to enhance membrane rejection and restore deteriorated membranes. Full article

Background/Objectives: The pulmonary administration of antibiotics can be advantageous in treating pulmonary infections by promoting high intrapulmonary drug concentrations with reduced systemic exposure. However, limited benefits have been observed for pulmonary administration versus other administration routes due to its rapid clearance from the lung. Here, the effects of structural modifications on the epithelial permeability and antibacterial potency of a third-generation cephalosporin were investigated to improve the understanding of drug properties that promote intrapulmonary retention and how they may impact efficacy. Methods: Ceftazidime was modified by attaching 18 hydrophobic, hydrophilic, and mucus-binding motifs to the carboxylic acid distant from the beta-lactam by amidation. Epithelial permeability was investigated by drug transport assays using human bronchial epithelial air–liquid interface cultures. Antibacterial potency was determined by microtiter MIC assays with B. pseudomallei, P. aeruginosa, E. coli, and S. aureus. Results: A 40–50% reduction in the transepithelial transport rate was exhibited by two PEGylated ceftazidime analogs (mPEG8- and PEG5-pyrimidin-2-amine-ceftazidime) and n-butyl-ceftazidime. An increase in the transport rate was exhibited by four analogs bearing small and hydrophobic or negatively charged motifs (n-heptane-, phenyl ethyl-, glutamic acid-, and 4-propylthiophenyl boronic acid-ceftazidime). The antibacterial potency was reduced by ≥10-fold for most ceftazidime analogs against B. pseudomallei, P. aeruginosa, and E. coli but was retained by seven ceftazidime analogs primarily bearing hydrophobic motifs against S. aureus. Conclusions: The covalent conjugation of PEGs with MW > 300 Da reduced the epithelial permeability of ceftazidime, but these modifications severely reduced antibacterial activity. To improve the pulmonary retention of antibiotics with low membrane permeability, this work suggests future molecular engineering studies to explore high-molecular-weight prodrug strategies. Full article

Anionic boron clusters, such as [B₁₂X₁₂]²⁻ (X = Cl, Br, I), have attracted attention in pharmaceuticals due to their unique superchaotropic properties. In particular, [B₁₂Br₁₂]²⁻ (1) has demonstrated strong interactions with biomolecules, facilitating cargo translocation across plasma membranes. In this study, we investigated the effect of covalently attaching chlorinated dodecaborate moiety [B₁₂Cl₁₁O-]²⁻ to 6-carboxyfluorescein (6-FAM) (3) via a PEG3 linker to form conjugate (4). We compared the membrane permeability of this covalent conjugate with that of non-covalent interactions between 6-FAM (3) and [B₁₂Cl₁₂]²⁻ (2). Live-cell fluorescence imaging revealed that the covalent conjugate exhibited enhanced membrane permeability and water solubility while maintaining low cytotoxicity. These results highlight the potential of covalent conjugation with boron clusters for improving the cellular uptake of hydrophilic cargos. Full article

Injectable, in situ-forming hydrogels, both biocompatible and biodegradable, have garnered significant attention in tissue engineering due to their potential for creating adaptable scaffolds. The adaptability of these hydrogels, made from natural proteins and polysaccharides, opens up a world of possibilities. In this study, sodium alginate was used to synthesize alginate di-aldehyde (ADA) through periodate oxidation, resulting in a lower molecular weight and reduced viscosity, with different degrees of oxidation (54% and 70%). The dual-crosslinking mechanism produced an injectable in situ hydrogel. Initially, physical crosslinking occurred between ADA and borax via borax complexation, followed by chemical crosslinking with gelatin through a Schiff’s base reaction, which takes place between the amino groups of gelatin and the aldehyde groups of ADA, without requiring an external crosslinking agent. The formation of Schiff’s base was confirmed by Fourier-transform infrared (FT-IR) spectroscopy. At the same time, the aldehyde groups in ADA were characterized using FT-IR, proton nuclear magnetic resonance (¹H NMR), and gel permeation chromatography (GPC), which determined its molecular weight. Furthermore, borax complexation was validated through boron-11 nuclear magnetic resonance (¹¹B NMR). The hydrogel formulation containing 70% ADA, polyethylene glycol (PEG), and 9% gelatin exhibited a decreased gelation time at physiological temperature, attributed to the increased gelatin content and higher degree of oxidation. Rheological analysis mirrored these findings, showing a correlation with gelation time. The swelling capacity was also enhanced due to the increased oxidation degree of PEG and the system’s elevated gelatin content and hydrophilicity. The hydrogel demonstrated an average pore size of 40–60 µm and a compressive strength of 376.80 kPa. The lower molecular weight and varied pH conditions influenced its degradation behavior. Notably, the hydrogel’s syringeability was deemed sufficient for practical applications, further enhancing its potential in tissue engineering. Given these properties, the 70% ADA/gelatin/PEG hydrogel is a promising candidate and a potential game-changer for injectable, self-crosslinking applications in tissue engineering. Its potential to revolutionize the field is inspiring and should motivate further exploration. Full article

The emergence of defects during the early production phases of ferrous-alloy additively manufactured (AM) parts poses a serious threat to their versatility and adversely impacts their overall mechanical performance in industries ranging from aerospace engineering to medicine. Lack of fusion and gas entrapment during the manufacturing stages leads to increased surface roughness and porosities in the finished part. In this study, the efficacy of employing electroless nickel–boron (Ni-B) deposition to fill and level simulated AM defects was evaluated. The approach to levelling was inspired by the electrochemical deposition techniques used to fill vias in the electronics industry that (to some extent) resemble the size and shape of AM-type defects. This work investigated the use of surfactants to attenuate surface roughness in electroless nickel coatings, thereby achieving the preferential inhibition of the coating thickness on the surface and promoting the filling of the simulated defects. A cationic surfactant molecule, CTAB (cetyltrimethyl ammonium bromide), and a nonpolar surfactant, PEG (polyethylene glycol), at different concentrations were tested using a Ni-B electrolyte for the levelling study. It was found that the use of electroless Ni-B to fill simulated defects on ferrous alloys was strongly influenced by the concentration and nature of the surfactant. The highest levelling percentages were obtained for the heavy-molecular-weight PEG-mediated coatings at 1.2 g/L. The results suggest that electroless Ni-B deposition could be a novel and facile approach to filling defects in ferrous-based AM parts. Full article

Chemotherapy is currently one of the most widely used treatments for cancer. However, traditional chemotherapy drugs normally have poor tumor selectivity, leading to insufficient accumulation at the tumor site and high systemic cytotoxicity. To address this issue, we designed and prepared a boronic acid/ester-based pH-responsive nano-drug delivery system that targets the acidic microenvironment of tumors. We synthesized hydrophobic polyesters with multiple pendent phenylboronic acid groups (PBA-PAL) and hydrophilic PEGs terminated with dopamine (mPEG-DA). These two types of polymers formed amphiphilic structures through phenylboronic ester linkages, which self-assembled to form stable PTX-loaded nanoparticles (PTX/PBA NPs) using the nanoprecipitation method. The resulting PTX/PBA NPs demonstrated excellent drug encapsulation efficiency and pH-triggered drug-release capacity. In vitro and in vivo evaluations of the anticancer activity of PTX/PBA NPs showed that they improved the pharmacokinetics of drugs and exhibited high anticancer activity while with low systemic toxicity. This novel phenylboronic acid/ester-based pH-responsive nano-drug delivery system can enhance the therapeutic effect of anticancer drugs and may have high potential for clinical transformations. Full article

Thermally conductive phase-change materials (PCMs) were produced using the crosslinked Poly (Styrene-block-Ethylene Glycol Di Methyl Methacrylate) (PS-PEG DM) copolymer by employing boron nitride (BN)/lead oxide (PbO) nanoparticles. Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) methods were used to research the phase transition temperatures, the phase-change enthalpies (melting enthalpy (ΔH_m), and crystallization enthalpies (ΔH_c)). The thermal conductivities (λ) of the PS-PEG/BN/PbO PCM nanocomposites were investigated. The λ value of PS-PEG/BN/PbO PCM nanocomposite containing BN 13 wt%, PbO 60.90 wt%, and PS-PEG 26.10 wt% was determined to be 18.874 W/(mK). The crystallization fraction (F_c) values of PS-PEG (1000), PS-PEG (1500), and PS-PEG (10,000) copolymers were 0.032, 0.034, and 0.063, respectively. XRD results of the PCM nanocomposites showed that the sharp diffraction peaks at 17.00 and 25.28 °C of the PS-PEG copolymer belonged to the PEG part. Since the PS-PEG/PbO and the PS-PEG/PbO/BN nanocomposites show remarkable thermal conductivity performance, they can be used as conductive polymer nanocomposites for effective heat dissipation in heat exchangers, power electronics, electric motors, generators, communication, and lighting equipment. At the same time, according to our results, PCM nanocomposites can be considered as heat storage materials in energy storage systems. Full article

Polyethylene glycol 1000 (PEG1000) and epoxy resin E20 were used to synthesize the E20/PEG1000 polymer (EP1K), which was later transformed into a self-emulsifying water-based epoxy curing agent by reacting with m-Xylylenediamine (MXDA). The effects of molecular weight, the molar ratio of the raw materials, the catalyst dosage, and the different co-solvents on the properties of the prepared curing agent were systematically explored. The infrared absorption spectra of E20, EP1K, and the water-based epoxy curing agent were compared and analyzed. The coating properties of the waterborne epoxy varnish, which was based on water-based epoxy curing agents to emulsify and cure the resin E44, were systematically tested. The results demonstrated that with a molar ratio of 1:1:4 of PEG1000, E20, and MXDA, the boron trifluoride etherate (BF₃·Et₂O) as catalyst accounts for 0.3% of the total mass of E20 and PEG1000, and an applicable period of 3 h for the prepared varnish, the anti-corrosion performance, and mechanical properties of the coatings were excellent. Full article

In vivo optical imaging is an important application value in disease diagnosis. However, near-infrared nanoprobes with excellent luminescent properties are still scarce. Herein, two boron–dipyrromethene (BODIPY) molecules (BDP-A and BDP-B) were designed and synthesized. The BODIPY emission was tuned to the near-infrared (NIR) region by regulating the electron-donating ability of the substituents on its core structure. In addition, the introduction of polyethylene glycol (PEG) chains on BODIPY enabled the formation of self-assembled nanoparticles (NPs) to form optical nanoprobes. The self-assembled BODIPY NPs present several advantages, including NIR emission, large Stokes shifts, and high fluorescence quantum efficiency, which can increase water dispersibility and signal-to-noise ratio to decrease the interference by the biological background fluorescence. The in vitro studies revealed that these NPs can enter tumor cells and illuminate the cytoplasm through fluorescence imaging. Then, BDP-B NPs were selected for use in vivo imaging due to their unique NIR emission. BDP-B was enriched in the tumor and effectively illuminated it via an enhanced penetrability and retention effect (EPR) after being injected into the tail vein of mice. The organic nanoparticles were metabolized through the liver and kidney. Thus, the BODIPY-based nanomicelles with NIR fluorescence emission provide an effective research basis for the development of optical nanoprobes in vivo. Full article

Sialic acid (SA) is a well-known component of glycoproteins, which have applications in various functional processes on the cell’s surface. The colorimetric is a simpler and more convenient method for measuring SA due to its low-cost apparatus and visual signal changes. This work focused on the unpredictable interparticle crosslinking aggregation of the functionalized gold nanoparticles (AuNPs) in complex media. We proposed a balance of the Derjaguin–Landau–Verwey–Overbeek (DLVO)-type aggregation and molecule-based interaction method to solve this problem. Here, we report a novel colorimetric assay for the determination of SA using 4-mercaptophenyl boronic acid (4-MPBA) as an analyte’s recognition molecule, and negative charge PEG₄₀₀ was used to repulsive the interparticle crosslinking. The proposed sensing platform shows a linear relationship between the ratio of the absorbance intensity (A₅₂₅/A₆₆₀) and concentration of SA from 0.05 to 8 mM (R² = 0.997) and a detection limit of 48 μM was observed. The novel gold-based colorimetric sensor is easy to fabricate, reproducible in its test performance and has been successfully applied for the detection of SA in biological and healthcare product samples. Full article

The mobility of sustained molecules is influenced by viscoelasticity, which is strongly correlated with the diffusional property in polymeric liquid. However, the study of transient networks formed by a reversible crosslink, which is the viscoelastic liquid, was insufficient due to the absence of a model system. We compare the viscoelastic and diffusional properties of the transient networks, using the model system with controlled network connectivity (Tetra-PEG slime). According to independent measurements of viscoelasticity and diffusion, the root-mean-square distance the polymer diffuses during the viscoelastic relaxation time shows a large deviation from the self-size of the polymer, which is contrary to the conventional understanding. This decoupling between viscoelasticity and diffusion is unique for transient networks, suggesting that the viscoelastic relaxation is not induced by the diffusion of one prepolymer, particularly in the network with low connectivity. These findings will provide a definite basis for discussion to understand the viscoelasticity in transient networks. Full article

Organic nanomaterials have attracted considerable attention in the area of photodynamic and photothermal therapy, owing to their outstanding biocompatibility, potential biodegradability, well-defined chemical structure, and easy functionalization. However, it is still a challenge to develop a single organic molecule that obtains both photothermal and photodynamic effects. In this contribution, we synthesized a new boron-dipyrromethene (BODIPY)-based derivative (DPBDP) with an acceptor–donor–acceptor (A-D-A) structure by coupling 3,6-di(2-thienyl)-2,5-dihydropyrrolo [3,4-c] pyrrole-1,4-dione (DPP) and BODIPY. To enhance the hydrophilicity of the BODIPY derivative, the polyethylene glycol (PEG) chains were introduced to the meso- position of BODIPY core. The amphiphilic DPBDP was then self-assembled into related nanoparticles (DPBDP NPs) with improved hydrophilicity and enhanced absorbance in the NIR region. DPBDP NPs could simultaneously generate the singlet oxygen (¹O₂) and heat under the irradiation of a single laser (690 nm). The ¹O₂ quantum yield and photothermal conversion efficiency (PCE) of DPBDP NPs were calculated to be 14.2% and 26.1%, respectively. The biocompatibility and phototherapeutic effect of DPBDP NPs were evaluated through cell counting kit-8 (CCK-8) assay. Under irradiation of 690 nm laser (1.0 W/cm²), the half maximal inhibitory concentration (IC₅₀) of DPBDP NPs was calculated to be 16.47 µg/mL. Thus, the as-prepared DPBDP NPs could be acted as excellent candidates for synergistic photodynamic/photothermal therapy. Full article

A new polymeric construct is proposed as a starting material for a liver-targeted delivery system in the present communication. The polymeric material has been designed to be sensitive to pH variations and potentially loaded with hydrophobic antitumoral agents. It is based on one of the most used copolymers in the field of nanomedicine: PEG-PLA. The latter, usually obtained by polymerization of lactic acid on the hydroxyl-terminated polyether, is assembled by the pH-reversible condensation between a phenylboronic acid-ended methoxy PEG 2000 (MeO-PEG2000-PBA) and a galactose-capped PLA of 1–10 kDa (PLA-Gal). Our approach is based on the strategic assumption that would allow a new ligand presentation strategy in which Gal is both a structural element for the stimulus-responsive PEG de-shielding and the targeting moiety. Indeed, Gal has a vicinal diol able to form a reversible boronate ester with a B(OH) 2 residue, which is cleavable at the acidic pH of the tumor microenvironment, and it is also recognized by the asialoglycoprotein receptor, which is hyper-expressed on the membrane of hepatocytes. The functionalization of the two blocks is presented here, and they are characterized using NMR, FTIR, and GPC. The analytical evaluation of the ability of the boronated PEG and Gal to condense in a pH sensible way completes the study. Full article

In this work, gamma-ray shielding features of crosslinked polystyrene-b-polyethyleneglycol block copolymers (PS-b-PEG) blended with nanostructured selenium dioxide (SeO₂) and boron nitride (BN) particles were studied. This research details several radiation shielding factors i.e., mass attenuation coefficient (${\mu }_m$), linear attenuation coefficient (${\mu }_L$), radiation protection efficiency (RPE), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP). The irradiation properties of our nanocomposites were investigated with rays from the ¹⁵²Eu source (in the energy intervals from 121.780 keV to 1408.010 keV) in a high-purity germanium (HPGe) detector system, and analyzed with GammaVision software. Moreover, all radiation shielding factors were determined by theoretical calculus and compared with the experimental results. In addition, the morphological and thermal characterization of all nanocomposites was surveyed with various techniques i.e., nuclear magnetic resonance (NMR), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM). Acceptable compatibility was revealed and observed in all nanocomposites between the experimental and theoretical results. The PS-b-PEG copolymer and nanostructured SeO₂ and BN particles exerted a significant effect in enhancing the resistance of the nanocomposites, and the samples with high additive rates exhibited better resistance than the other nanocomposites. From the achieved outcomes, it can be deduced that our polymer-based nanocomposites can be utilized as a good choice in the gamma-irradiation-shielding discipline. Full article

Chemotherapy has led to many undesirable side effects, as these are toxic drugs that are unable to differentiate between cancer and normal cells. Polyphenols (tea catechins) are an ideal option as alternative chemotherapeutics owing to their inherent anticancer properties, antioxidant properties and being naturally occurring compounds, are deemed safe for consumption. However, without proper administration, the bioavailability of these compounds is low and inefficient. Therefore, proper delivery of these phenolic compounds is vital for cancer therapy. Herein, we analyzed three potential solutions to creating nanoparticle drugs using naturally occurring phenolic compounds (piceatannol (PIC), epigallocatechin gallate hydrophilic (EGCG) and l-epicatechin (EPI)). By using a simple pi-pi stacking mechanism, we utilized boronated PEG (PEG-Br) as an anchor to efficiently load EPI, PIC and EGCG, respectively, to produce three effective phenolic compound-based nanoparticles, which could be delivered safely in systemic circulation, yet detach from its cargo intracellularly to exert its anticancer effect for effective cancer therapy. Full article