Search Results (51)

During high-current vacuum arcing, asymmetric arcing with off-center plasma columns may occur due to stochastic discharge initiation and mechanical motion, receiving less research attention than symmetric arcing. The objective of this paper is to numerically analyze the influence law of asymmetric arc ignition on arc parameters. For 60 mm diameter contacts, three arc conditions of symmetric arcing, 33% arc offset, and 67% arc offset were modeled. The results show that the arc offset causes asymmetry in the arc’s distribution. For 33% offset, the pressure and number density on the side away from the root of the arc is about 50% of root values, while these parameters fall below 20% for the 67% offset. Simultaneously, arc offset elevates peak parameter values: under 33% offset, maxima for ion pressure, ion density, ion temperature, electron temperature, and current density rise 12%, 11%, 6%, 6%, and 14% versus symmetric arcing; during 67% offset, these escalate significantly to 67%, 61%, 12%, 18%, and 47%. This study contributes to providing reference for the analysis of vacuum interruption processes under asymmetric arcing conditions. Full article

Breath-actuated nebulizers used in aerosol therapy are vital to children and patients with disabilities and stand out for their ability to accurat ely deliver medication while minimizing waste. Their performance can be measured according to the mass output and droplet size. This study aimed to analyze how the baffle impact surface geometries affect the pressure and flow streamlines inside the nebulizer using computational fluid dynamics (CFD). Computer-aided design models of conical symmetric, conical asymmetric, and arc-shaped baffle designs were analyzed using CFD simulations, with the optimal spray output validated through the differences in mass. Conical baffles exhibited superior pressure distribution and output streamlines at 0.25 cm protrusion, suggesting that the nebulizer spray performance can be enhanced by using such a conical baffle impact surface. This result serves as a valuable reference for future research. Full article

To address the stability control challenges of the “support-surrounding rock” system in fully mechanized top-coal caving faces within steeply dipping coal seams, this study employs an integrated approach combining theoretical analysis and numerical simulations, revealing the three-dimensional boundary morphology of the top-coal limit equilibrium zone and establishing a quantitative framework for boundary delineation. The results show that the boundary spatial morphology of the limit equilibrium zone in the fully mechanized caving stope in steeply dipping coal seams is an “asymmetric arc-shaped ribbon-like curved surface”. Along the inclined direction of the working face, the boundary distribution presents an “asymmetric circular-arc arch”, with the vault located in the middle-upper part of the working face. Along the strike direction of the working face, the distance from the boundary to the longwall face shows a gradually increasing pattern from top to bottom. Upon comparing the results from the numerical simulation, theoretical calculation, and field monitoring, a consistent overall pattern emerges. This consistency validates the rationality of the analytical representation of the boundary of the top-coal limit equilibrium zone. The research findings hold significant importance in predicting the stability of the “support-surrounding rock” system and the top-coal cavability. They can offer a scientific foundation for guiding the stability control practices of the support–surrounding rock within this type of mining stope. Full article

In this paper, we develop a new family of distributions supported on a bounded interval with a probability density function that is constructed from two elliptical arcs. The distribution can take on a variety of shapes and has three basic parameters: minimum, maximum, and mode. Compared to classical bounded distributions such as the beta and triangular distributions, the proposed semi-elliptical family offers greater flexibility in capturing diverse shapes of distributions, in symmetric and asymmetric settings. Its construction from elliptical arcs enables smoother transitions and more natural tail behaviors, making it suitable for applications where classical models may exhibit rigidity or over-simplicity. We give general expression for the density and distribution function of the new distribution. Properties of this distribution are studied and parameter estimation is discussed. Monte Carlo simulation results show the performance of our estimators under many sets of situations. Furthermore, we show the advantages of our distribution over the commonly used triangular distribution in approximating beta distributions. Full article

This study presents an enhanced analytical approach for one-dimensional consolidation settlement by introducing a revised AJOP (arc joint via optimum parameters) equation assuming creep and strain rate effects can be neglected for both normally and overconsolidated clays. This modified equation integrates both curved and linear segments within a unified framework, enhancing accuracy across varying stress levels for normally consolidated clay. Additionally, the revised AJOP function, coupled with newly proposed equations for symmetrical and asymmetrical hysteresis, improves the modeling of overconsolidated clay. The findings from a comparative investigation using benchmark datasets and conventional methods, including the linear function (LF) and the curved function (CF), reveal that the revised AJOP method was found to reduce settlement prediction errors by up to 85% compared to LF method (particularly at shallow layers) and by 10–15% compared to the CF method (particularly at deep layers). The revised AJOP equation effectively resolves this error with a wide range of depths. Furthermore, results highlight the crucial impact of clay layering techniques on consolidation settlement predictions. Non-layered models yield lower settlement estimates compared to multilayer approaches, emphasizing the significance of the proper $e-log{{\mathsf{\sigma }}^{\prime }}_v$ relationship and layering techniques in enhancing prediction reliability. Full article

Traditional offline programming has limitations for large parts with significant machining or assembly deviations. This study proposes a 3D scanning-assisted method that generates accurate STereoLithography (STL) models and enables multi-layer multi-bead welding trajectory planning for large intersecting line workpieces. The proposed framework implements a robust STL model processing pipeline incorporating Random Sample Consensus (RANSAC)-based cylindrical approximation, cross-sectional slicing, and automated feature detection to achieve high-precision groove feature recognition. For asymmetric variable-section grooves, a multi-layer and multi-pass path-planning algorithm based on template affine projection transformation is developed to ensure accurate deposition of welds along complex geometric contours. Experimental validation demonstrates sub-millimeter trajectory accuracy (positional errors < 1.0 mm), meeting stringent arc welding specifications and substantially expanding the applicability of offline programming systems. Full article

Photic retinopathy is an uncommon clinical entity characterized by retinal damage brought on by excessive exposure to light without protection. It encompasses several distinct clinical categories, including solar maculopathy, handheld laser maculopathy, arc welding maculopathy, and iatrogenic macular degeneration. These clinical entities result from exposure to diverse light sources, such as solar radiation, laser pointers, welding arcs, and operating microscopes during ophthalmic procedures. Patients typically present with bilateral but asymmetric symptoms, including reduced visual acuity, central or paracentral scotomas, photophobia, metamorphopsia, and headaches. After exposure, most people can recover on their own in a matter of weeks to six months without the need for special care. However, thanks to their anti-inflammatory properties, several clinical cases reporting the use of steroids for acute photic retinopathy have been documented in the scientific literature, together with the use of antioxidants. The purpose of this review is to provide an update on this phototoxic maculopathy, describing its different clinical entities, diagnosis, and treatment options, and also focusing on the role of optical coherence tomography for its management. Full article

To address challenges in locating high-impedance grounding faults (HIGFs) and isolating fault areas in resonant grounding systems, this paper proposes a novel fault identification method based on coordinating a Peterson coil and a resistance grounding system. This method ensures power supply reliability by extinguishing the fault arc during transient faults with the Peterson coil. When a fault is determined to be permanent, the neutral point switches to a resistance grounding mode, ensuring regular distribution of zero-sequence currents in the network, thereby addressing the challenges of HIGF localization and fault area isolation. Fault calibration and nature determination rely on recognizing neutral point displacement voltage waveforms and dynamic characteristics, eliminating interference from asymmetric phase voltage variations. Fault area identification involves assessing the polarity of zero-sequence current waveforms attenuation during grounding mode switching, preventing misjudgments in grounding protection due to random initial fault angles and Peterson coil compensation states. Field experiments validate the feasibility of this fault location method and its control strategy. Full article

This study investigated how welding affects the thermal deformation of square cells produced for casks, which are dry storage containers for spent nuclear fuel. We aimed to minimize structural deformation by utilizing STS316L as the material for the square cells. We explored a method of subdividing the square cells and joining them through butt welding. Keeping the upper plate thickness constant, GTA butt welding was conducted while varying the column’s wall thickness, followed by measurement with a laser vision sensor. The heat conduction and thermal strain were then calculated using a finite element analysis (FEM). Both experimental and analytical results confirmed that there was significant thermal deformation in the cases of thick-walled columns due to variations in heat conduction distribution, with the resulting deformation patterns depending on thickness. Full article

The eastern Qaidam Basin (EQB), along with its surrounding orogenic belts, witnessed complicated tectonic movements in the period from the late Paleozoic to the early Mesozoic. As strategic succeeding strata, the Carboniferous strata (CST) in the EQB have gradually become a research hotspot in recent years. However, the question of how tectonism controlled the tempo-spatial evolution of the CST has yet to be studied. To resolve these issues, we collated statistics related to unconformities, seismic interpretation, and basin modeling in this study. The results show that the structure of the CST was mostly controlled by NNE-striking faults, namely the Zongjia and Ainan Fault, in the period from the Carboniferous to the Triassic time. During the Carboniferous time, the sedimentation of the CST was controlled by medium-high angle potential normal faults. The CST experienced two stages of tectonic subsidence and subsequent burial: the highest average subsidence and burial rate of 45 m/Ma and 12 m/Ma occurred at 340~285 Ma, decreasing to 15 m/Ma and 7.5 m/Ma between 305 Ma and 250 Ma. However, the maximum burial (~5500 m) took place at ~250 Ma. From the end of the late Permian to the late Triassic (254~195 Ma), the overall exhumation rate of the CST has averaged 38.71 m/Ma, and 75 m/Ma in the southern margin of the Huobuxun Depression. The CST near the piedmont margins of the EQB suffered essential denudation at 254~195 Ma, resulting in small amounts of the residual CST. In these areas, the CST were deformed with a steepening dip during this time and were characterized by the combinations of syncline-anticlinal asymmetric folds with the high-angle interlimb. These findings indicated that the tempo-spatial evolution of the CST was possibly influenced by the sedimentary and tectonic transition, and was a combined response to Paleo-Tethys Ocean subduction, and arc-continental collisions since the late Paleozoic to early Mesozoic periods. Full article

During the refining stage of electric arc furnace (EAF) operation, molten steel is stirred to facilitate gas/steel/slag reactions and the removal of impurities, which determines the quality of the steel. The stirring process can be driven by the injection of oxygen, which is carried out by burners operating in lance mode. In this study, a computational fluid dynamics (CFD) platform is used to simulate the liquid steel flow dynamics in an industrial-scale scrap-based EAF. The CFD platform simulates the three-dimensional, transient, non-reacting flow of the liquid steel bath stirred by oxygen injection to analyze the mixing process. In particular, the CFD study simulates liquid steel flow in an industrial-scale EAF with three asymmetric coherent jets, which impacts the liquid steel mixing under different injection conditions. The liquid steel mixing is quantified by defining two variables: the mixing time and the standard deviation of the flow velocity. The results indicate that the mixing rate of the bath is determined by flow dynamics near the injection cavities and that the formation of very low-velocity regions or ‘dead zones’ at the center of the furnace and the balcony regions prevents flow mixing. This study includes a baseline case, where oxygen is injected at 1000 SCFM in all the burners. Two sets of cases are also included: The first set considers cases where oxygen is injected at a reduced and at an increased uniform flow rate, 750 and 1250 SCFM, respectively. The second set considers cases with non-uniform injection rates in each burner, which keep the same total flow rate of the baseline case, 3000 SCFM. Comparison between the two sets of simulations against the baseline case shows that by increasing the uniform flow rate from 1000 to 1250 SCFM, the mixing time is reduced by 10.9%. Moreover, all the non-uniform injection cases reduce the mixing time obtained in the baseline case. However, the reduction in mixing times in these cases is accompanied by an increase in the standard deviations of the flow field. Among the non-uniform injection cases, the largest reduction in mixing time compared to the baseline case is 10.2%, which is obtained when the largest flow rates are assigned to coherent jets located opposite each other across the furnace. Full article

The calculation of conformal mapping for irregular domains is a crucial step in deriving analytical and semi-analytical solutions for irregularly shaped tunnels in rock masses using complex theory. The optimization methods, iteration methods, and the extended Melentiev’s method have been developed and adopted to calculate the conformal mapping function in tunnel engineering. According to the strict definition and theorems of conformal mapping, it is proven that these three methods only map boundaries and do not guarantee the mapping’s conformal properties due to inherent limitations. Notably, there are other challenges in applying conformal mapping to tunnel engineering. To tackle these issues, a practical procedure is proposed for the conformal mapping of common tunnels in rock masses. The procedure is based on the extended SC transformation formulas and corresponding numerical methods. The discretization codes for polygonal, multi-arc, smooth curve, and mixed boundaries are programmed and embedded into the procedure, catering to both simply and multiply connected domains. Six cases of conformal mapping for typical tunnel cross sections, including rectangular tunnels, multi-arc tunnels, horseshoe-shaped tunnels, and symmetric and asymmetric multiple tunnels at depth, are performed and illustrated. Furthermore, this article also illustrates the use of the conformal mapping method for shallow tunnels, which aligns with the symmetry principle of conformal mapping. Finally, the discussion highlights the use of an explicit power function as an approximation method for symmetric tunnels, outlining its key points. Full article

Renewable energy sources have a multifaceted impact on power grids, ranging from the reliability and quality of electricity to the selective impact on equipment. While renewables used to be distributed in distribution networks, now their capacity is commensurate with thermal power plants and their impact on the grid should not be underestimated. According to the statistics on the interruption of the bulk electric networks, one of the main reasons for emergency shutdowns of extra high-voltage power lines are single-phase short circuits. The problem of mathematical modeling of the limit modes in terms of static stability is very relevant to the design and operation of electric power systems (EPS). Calculations of limit modes have both an independent value and a component of other electrical engineering tasks related to ensuring the required level of reliability and cost-effectiveness of the operation of the united PS. Despite the great degree of development of issues of planning and control of electric modes, system accidents associated with unacceptable loads of network elements occur in the Ukrainian energy industry. Non-phase modes regularly occur in electric power systems, which can lead to an unacceptable load of intersystem network elements, which imposes significant restrictions on their throughput. Single-phase short circuits are more than 95% of other damage that occurs in the line. The use of single-phase auto reclose on the transmission lines allows disconnecting only the damaged phase for a short period of time and not the entire transmission line. This action preserves the transit of electricity along the line and prevents the violation of the stability of parallel operation. To achieve this, the current-free pause of the single-phase auto reclose should last as short as possible. On the other hand, an important task to be solved when using single-phase auto reclose is to choose the minimum duration of the current-free pause necessary for its success. The problem studied in this paper deals with the safety and correct operation of transmission lines (TS) of the Ukrainian bulk power system in special conditions (not predictable, changing due to frequent attacks). For a quickly changing configuration, the power grid uses switches, and in the case of ultra-high voltage, the TS needs to solve the problem of secondary arc currents and recovering stresses in the place of arc burning after its extinction. One of the methods of reducing secondary arc currents and recovering stresses in the place of arc burning after its extinction is the implementation of single-phase automatic reclosing (SPAR). The main theoretical result of the paper is a proposed mathematical model of a compensated power transmission line based on the use of matrix n-poles, which makes it possible to model in detail stationary power transmission modes, including the SPAR mode. The proposed mathematical model of three-phase power transmission has been created using phase coordinates and can be used for the analysis of complex asymmetric modes. The main practical result of the paper is physically interpreted simplified models of three-phase TS, which can be used for the study of resonant overvoltages and currents of the feeding arc in non-full-phase circuit SPAR. The conclusion that can be drawn from the obtained results points out which line lengths must take into account the influence of longitudinal asymmetry when choosing the inductive resistance, i.e., take into account the dependence of the mode parameters on the location of the damaged phase. The observed results show that the largest values of the multiplicity of overvoltages will take place in phase B. The novelty of the work is the developed technique that makes it possible to determine in advance, depending on the disconnected phase of the line, the values of the primary conductivities of the STC (static thyristor compensators) and the corresponding angles of control of the thyristor switches, which satisfy almost complete compensation of the secondary arc at any point of the line in the specific condition (hard) of the bulk power system operation. Full article

To address the problems of low resolution, compression artifacts, complex noise, and color loss in image restoration, we propose a High-Quality Prior-Guided Blind Face Restoration Generative Adversarial Network (HPG-GAN). This mainly consists of Coarse Restoration Sub-Network (CR-Net) and Fine Restoration Sub-Network (FR-Net). HPG-GAN extracts high-quality structural and textural priors and facial feature priors from coarse restoration images to reconstruct clear and high-quality facial images. FR-Net includes the Facial Feature Enhancement Module (FFEM) and the Asymmetric Feature Fusion Module (AFFM). FFEM enhances facial feature information using high-definition facial feature priors obtained from ArcFace. AFFM fuses and selects asymmetric high-quality structural and textural information from ResNet34 to recover overall structural and textural information. The comparative evaluations on synthetic and real-world datasets demonstrate superior performance and visual restoration effects compared to state-of-the-art methods. The ablation experiments validate the importance of each module. HPG-GAN is an effective and robust blind face deblurring and restoration network. The experimental results demonstrate the effectiveness of the proposed network, which achieves better visual quality against state-of-the-art methods. Full article

Asymmetry, such as non-centrosymmetry in the crystal or chiral structure and local symmetry breaking, plays an important role in the discovery of new phenomena. The honeycomb structure is an example of an asymmetric structure. Ce${}_2$Pt${}_6$Al${}_{15}$ is a candidate for a frustrated system with honeycomb Ce-layers, which have been reported to show near the quantum critical point. However, the ground state of Ce${}_2$Pt${}_6$Al${}_{15}$ depends on the sample, and analysis of the crystal structure is difficult due to the presence of stacking disorder. We synthesized polycrystalline Ce${}_2$Pt${}_6$Al${}_{15}$ using arc melting method (AM-Ce${}_2$Pt${}_6$Al${}_{15}$) and single-crystalline Ce${}_2$Pt${}_6$Al${}_{15}$ using flux method (F-Ce${}_2$Pt${}_6$Al${}_{15}$). The prepared samples were characterized by electron probe micro-analysis (EPMA), single and powder X-ray diffraction methods, measured magnetic properties and X-ray absorption spectroscopy (XAS). The composition ratio of AM-Ce${}_2$Pt${}_6$Al${}_{15}$ was stoichiometric, although it contained a small amount (i.e., a few percent) of the impurity Ce${}_2$Pt${}_9$Al${}_{16}$. Meanwhile, the composition ratio of F-Ce${}_2$Pt${}_6$Al${}_{15}$ deviated from stoichiometry. The X-ray absorption fine structure (XAFS) spectrum of AM-Ce${}_2$Pt${}_6$Al${}_{15}$ at the Ce L${}_3$-edge was similar to that of CeF${}_3$, which possesses the Ce${}^{3+}$ configuration, indicating that the valence of Ce in Ce${}_2$Pt${}_6$Al${}_{15}$ is trivalent; this result is consistent with that for the magnetic susceptibility. To determine the precise structure, we analyzed the extended X-ray absorption fine structure (EXAFS) spectra of Ce L${}_3$- and Pt L${}_3$-edges for Ce${}_2$Pt${}_6$Al${}_{15}$, and found that the EXAFS spectra of Ce${}_2$Pt${}_6$Al${}_{15}$ can be explained not as a hexagonal Sc${}_{0.6}$Fe${}_2$Si${}_{4.9}$-type structure but, instead, as an orthorhombic structure with honeycomb structure. Full article