Search Results (780)

Ammonia emissions in poultry houses are common and pose health concerns for animals and workers. However, effective control of these emissions with sustainable products is lacking. Therefore, we investigated if an agricultural byproduct, cottonseed hulls, could be recycled through pyrolysis and used to remove ammonia from air. In this study, the efficacy of ammonia removal was observed using cottonseed hull biomaterials pyrolyzed at seven different temperatures: 250, 300, 350, 400, 500, 600, and 700 °C. In this study, ammonia was passed through a column filled with pyrolyzed material, and ammonia in the filtered air was monitored. The results showed that materials pyrolyzed at intermediate temperatures of 350 and 400 °C were the most efficient at ammonia removal and were able to adsorb approximately 3.7 mg NH₃/g of material. Despite extensive characterization, ammonia adsorption could not be linked to intrinsic material properties. Evaluation of the materials showed that the carbon in the pyrolyzed materials would be stable over time should the spent material be used as a soil amendment. Full article

To address the slow growth rate of photosynthetic bacteria (PSB), this study introduces pantothenic acid as a biological enhancing factor. The effects of pantothenic acid on PSB proliferation and its effectiveness in treating high-concentration ammonia–nitrogen wastewater were systematically evaluated. Additionally, the effects of different culture conditions, including dark aeration, darkness, light exposure, and light aeration, on PSB growth were investigated. The results show that optimal PSB growth was achieved with 20 mg/L of pantothenic acid; however, higher concentrations of pantothenic acid inhibited bacterial growth. The addition of pantothenic acid also significantly enhanced the performance of PSB in treating high-concentration organic wastewater, increasing the removal rates of COD, ammonia nitrogen, total phosphorus, and total nitrogen to 43.0%, 94.0%, 49.7%, and 51.0%, respectively. Furthermore, a synergistic effect between dark aeration and light exposure was observed. When the time of light and dark aeration was set at 1:1, the highest PSB yield was recorded, and the removal efficiencies of COD, ammonia nitrogen, total nitrogen, and total phosphorus increased to 71.4%, 95.3%, 57.1%, and 74.7%, respectively. Through the introduction of pantothenic acid and optimization of culture mode, the rapid growth of PSB and highly efficient treatment of organic wastewater were achieved, providing a new approach for advanced wastewater treatment and resource utilization. Full article

This paper presents the assessment of the possibility of ammonia adsorption on biochars from banana peels, chemically activated with potassium hydroxide (KOH) at different temperatures. The obtained materials were characterized in detail using a number of analytical techniques, including nitrogen adsorption (BET), scanning electron microscopy (SEM), elemental analysis (CHNS), thermal analysis (TG, DTG, DTA), Fourier transform infrared spectroscopy (ATR-FTIR), Raman spectroscopy, Boehm titration method and biochar surface pH. They revealed a largely developed microporous structure and a large specific surface area, ranging from 1134 to 2332 m² g⁻¹. The adsorption tests against ammonia in the gas phase showed a large adsorption capacity of the materials, up to 5.94 mmol g⁻¹ at 0 °C and 3.83 mmol g⁻¹ at 20 °C. The adsorption properties of the obtained biochars were confirmed to be significantly influenced by the surface chemistry (presence of the acidic functional groups). The research results indicate that the waste-based biomass, such as banana peels, can be an ecological and economical raw material for the production of highly effective adsorbents, useful in the removal of ammonia and other toxic gases polluting the environment. Full article

This study examined a strategy for effective reject water treatment involving hydrodynamic cavitation (HC) combined with subsequent adsorption using natural zeolites. Two experiments were conducted: The first involved the selection of optimal pre-treatment conditions of HC for biodegradability and to reduce the ammonium nitrogen and phosphate content. Three inlet pressures of 3, 5, and 7 bar and two types of cavitation inducers, i.e., multiple- and single-hole orifice plates, were evaluated. Adsorption experiments were conducted in batch mode using natural zeolite, and three doses of zeolite (50, 100, and 200 g/L) and six contact times (4–24 h) were examined. In the HC experiments, the application of 3 bar pressure, a single-hole cavitation inducer, and a cavitation time of 30 min resulted in the removal of ammonia nitrogen and phosphates amounting to 26.5 and 23%, respectively. In this case, 3.6-fold enhancement in the biodegradability index was also found. In the second experiment, the use of zeolite led to a decrease in the remaining content of both ammonia nitrogen and phosphates, improving the chemical oxygen demand-to-total nitrogen ratio. The highest removal efficacy was found for the highest zeolite dose of 200 g/L and the longest cavitation time of 24 h. Under these conditions, the ammonia nitrogen and phosphate removal rates were 70 and 94%, respectively. Full article

A 56-day trial was conducted to assess the effects of rice straw (RS) and bamboo flour (BF) on growth performance, water quality, gill histology, and the bacterial community of water and the intestine of mandarin fish (Siniperca chuatsi) in biofloc technology systems. The results showed that mandarin fish in the RS and BF groups had comparable survival rates of 100.00 ± 0.00 and 93.33 ± 3.85%; feed conversion ratios of 1.13 ± 0.02 and 1.40 ± 0.15; and weight gain rates of 112.21 ± 1.56 and 100.92 ± 6.45%, respectively. From days 11 to 56 of the farming period, the BF group was more effective than the RS group in removing total ammonia nitrogen (TAN) and NO₂⁻-N, maintaining TAN levels below 0.24 ± 0.05 mg/L. During the early stage of the experiment, the TAN level in the RS group was higher; however, with the supplementation of a carbon source, it gradually decreased and eventually stabilized at 0.13 ± 0.03 mg/L later in the farming period. The secondary gill lamella in the RS group was curved and showed hyperplasia, and the basal gill lamellae showed an increase in the volume of interlamellar cell mass in the BF group. Genes related to denitrification (narG, napA, nirS, nirK, and nosZ) and anammox showed higher expression levels in the BF group than in the RS group, although the differences were not statistically significant (p > 0.05). The results of 16S rRNA sequencing research showed that both treatment groups’ intestinal and water bacterial communities had comparable levels of richness and diversity. Pseudomonas mosselii was the dominant bacterial species in the water. In the BF group, the dominant intestinal species were Bacillus halodurans and Caldalkalibacillus thermarum, while in the RS group, the dominant species was Plesiomonas shigelloides. In conclusion, rice straw and bamboo flour are applicable in BFT systems for mandarin fish culture, with good growth performance and water quality. The BF group showed higher nitrogen removal efficiency and denitrification gene expression than the RS group. Full article

Anaerobic digestion (AD) for food waste (FW) treatment has faced many challenges, especially ammonia nitrogen, acid, and salinity inhibition at a high organic loading rate (OLR). Therefore, a systematic understanding of the issues arising during the FW AD process is a necessity under a high OLR (over 3 g-VS/L d). Primarily, in terms of ammonia nitrogen inhibition, ammonia ions inhibit methane synthesis enzymes, and free ammonia (FAN) contributes to the imbalance of microbial protons. Regulation strategies include substrate C/N ratio regulation, microbial domestication, and ammonia nitrogen removal. In addition, with regard to acid inhibition, including volatile fatty acid (VFA) and long-chain fatty acid (LCFA) accumulation, the elevated acid concentration can contribute to reactive oxygen species stress, and a solution to this includes the addition of alkaline agents and trace elements or the use of microbial electrochemical and biofortification technology and micro-aeration-based AD technology. Furthermore, in terms of salinity inhibition, high salinity can result in a rapid increase in cell osmotic pressure, which can cause cell rupture, and water washing and bio-electrochemical AD are defined as solutions. Future research directions are proposed, mainly in terms of avoiding the introduction of novel containments into these regulation strategies and applying them in large-scale AD plants under a high OLR. Full article

High-ammonia-nitrogen organic wastewater poses significant challenges to traditional nitrogen removal processes due to their high energy consumption and carbon dependency, conflicting with global sustainability goals. Anammox presents a sustainable alternative with lower energy demands, yet its application is constrained by organic matter inhibition. This study aimed to optimize nitrogen and organic matter removal in Anammox systems by comparing two strategies: effluent recirculation and micro-aeration. Anammox reactors were operated under three conditions: (1) no recirculation (control group), (2) 100–300% effluent recirculation, (3) micro-aeration at 50–150 mL/min. The effects on total nitrogen (TN) and chemical oxygen demand (COD) removal were evaluated, alongside microbial community analysis via high-throughput sequencing. The results show that micro-aeration at 100 mL/min achieved 78.9% COD and 88.3% TN removal by creating micro-anaerobic conditions for metabolic synergy. Excessive aeration (150 mL/min) inhibited Anammox, dropping TN removal to 49.7%. Recirculation enriched Planctomycetota, while micro-aeration slightly increased Planctomycetota abundance at 45 cm and enhanced Proteobacteria and Chloroflexi for denitrification. Optimal conditions—200% recirculation and 100 mL/min aeration—improve efficiency via dilution and synergistic metabolism, providing a novel comparative framework for treating high-ammonia-nitrogen organic wastewater and filling a research gap in the parallel evaluation of Anammox enhancement strategies. Full article

The electrochemical reduction of nitrate to ammonia offers a promising solution for both alleviating nitrate pollution in wastewater and providing a sustainable ammonia source for agriculture use. This review focuses on the role of carbon-based catalysts in electrochemical nitrate reduction to ammonia, emphasizing their potential in addressing environmental pollution and supporting sustainable ammonia production. Carbon materials, known for their abundance, affordability, and eco-friendly properties, are central to this process. The review highlights key strategies for enhancing catalytic performance, including heteroatom doping, the development of porous structures, and the integration of metal/metal oxide nanoparticles. Additionally, it addresses significant challenges such as weak nitrate adsorption, slow reaction kinetics, and competition with the hydrogen evolution reaction. Through the integration of advanced material design, mechanistic insights, and innovative engineering strategies, this review provides valuable guidance for the future design of carbon-based catalysts, paving the way for significant advancements in both nitrate removal and sustainable ammonia synthesis. Full article

The recirculating aquaculture system (RAS) has been rapidly adopted worldwide in recent years due to its high productivity, good stability, and good environmental controllability (and therefore friendliness to environment and ecology). Nevertheless, the effluent from seawater RAS contains a high level of ammonia nitrogen which is toxic to fish, so it is necessary to overcome the salinity conditions to achieve rapid and efficient nitrification for recycling. The moving bed biofilm reactor (MBBR) has been widely applied often by using PE fillers for efficient wastewater treatment. However, the start-up of MBBR in seawater environments has remained a challenge due to salinity stress and harsh inoculation conditions. This study investigated a new PE-filler surface modification method towards the enhanced start-up of mariculture MBBR by combining liquid-phase oxidation and maifanstone powder. The aim was to obtain a higher porous surface and roughness and a strong adsorption and alkalinity adjustment for the MBBR PE filler. The hydrophilic properties, surface morphology, and chemical structure of a raw polyethylene filler (an unmodified PE filler), liquid-phase oxidation modified filler (LO-PE), and liquid-phase oxidation combined with a coating of a maifanstone-powder-surface-modified filler (LO-SCPE) were first investigated and compared. The results showed that the contact angle was reduced to 45.5° after the optimal liquid-phase oxidation modification for LO-PE, 49.8% lower than that before modification, while SEM showed increased roughness and surface area by modification. Moreover, EDS presented the relative content of carbon (22.75%) and oxygen (42.36%) on the LO-SCPE surface with an O/C ratio of 186.10%, which is 177.7% higher than that of the unmodified filler. The start-up experiment on MBBRs treating simulated marine RAS wastewater (HRT = 24 h) showed that the start-up period was shortened by 10 days for LO-SCPE compared to the PE reactor, with better ammonia nitrogen removal observed for LO-SCPE (95.8%) than the PE reactor (91.7%). Meanwhile, the bacterial community composition showed that the LO-SCPE reactor had a more diverse and abundant AOB and NOB. The Nitrospira has a more significant impact on nitrification because it would directly oxidize NH₄⁺-N to NO₃⁻-N (comammox pathway) as mediated by AOB and NOB. Further, the LO-SCPE reactor showed a higher NH₄⁺-N removal rate (>99%), less NO₂⁻-N accumulation, and a shorter adaption period than the PE reactor. Eventually, the NH₄⁺-N concentrations of the three reactors (R1, R2, and R3) reached <0.1 mg/L within 3 days, and their NH₄⁺-N removal efficiencies achieved 99.53%, 99.61%, and 99.69%, respectively, under ammonia shock load. Hence, the LO-SCPE media have a higher marine wastewater treatment efficiency. Full article

This study investigates the optimization of an ammonia-based leaching process for the recovery of lithium and cobalt from spent LiCoO₂ cathodes, coupled with an energy-efficient ammonia stripping approach. Kinetic analysis revealed that both lithium and cobalt extraction follow pseudo-first-order kinetics, with activation energies of 76.54 kJ/mol and 97.22 kJ/mol, respectively, indicating a chemically controlled process. Optimal leaching conditions were established at 6 M NH₃, 1.5 M (NH₄)₂CO₃, liquid-to-solid ratio of 10:1, and 70 °C for 5 h, achieving 82.5% lithium and 96.1% cobalt recovery. The ammonia stripping process was optimized for energy efficiency, with operations at 95–98 °C providing the best balance between rapid NH₃ removal and energy consumption. At 98 °C, energy demand was reduced to ~282 kJ/mol, a sevenfold improvement over lower temperature operations. A stepwise separation strategy was developed, involving selective lithium precipitation at pH 10.7–10.8, followed by controlled ammonia stripping to precipitate cobalt at pH 8.8–9.0. This integrated approach offers a promising alternative to conventional acid-based recycling methods, combining high metal recovery with improved energy efficiency and reagent recyclability. Full article

This study evaluated the pollutant removal efficiency of two decentralized wastewater treatment plants (WWTPs) located in the high-altitude southern Andes of Ecuador, Acchayacu and Churuguzo, from 2015 to 2024. Acchayacu previously operated using an upflow anaerobic filter (UAF), and from 2021, it transitioned to using vertical-subsurface-flow constructed wetlands (VSSF-CWs). In contrast, Churuguzo employs surface-flow constructed wetlands (SF-CWs). These systems were assessed based on parameters such as the five-day biochemical oxygen demand (BOD₅), chemical oxygen demand (COD), total phosphorus, organic nitrogen, ammonia nitrogen, total solids, fecal coliforms (TTCs), and total coliforms (TCs). The data were divided into two subperiods to account for the change in technology in Acchayacu. Statistical analysis was conducted to determine whether significant differences existed between the treatment efficiencies of these technologies, and the SF-CW was found to consistently outperform both the UAF and VSSF-CW in removing organic matter and microbial pollutants. This difference is likely attributed to the longer hydraulic retention time, lower hydraulic loading rate, and vegetation type. The findings highlight the environmental implications of treatment technology selection in WWTPs, particularly regarding the quality of receiving water bodies and their potential applications for public health, proper water resource management, and the design of decentralized systems in high-altitude regions, especially in developing countries. Full article

Microalgae–fungal pellets (MFPs) effectively degrade pollutants in high-density aquaculture wastewater; however, their structural instability limits their long-term applicability. This study evaluated the effects of three crosslinking agents, sodium alginate (SA), chitosan (CTS), and polyvinyl alcohol (PVA), on enhancing the stability of MFPs. The results demonstrated that the initial 20 g/L SA-crosslinked MFP sample (SMFP₀) exhibited significantly improved structural stability, maintaining superior mechanical hardness (57.05 g) after 9 days. Further analysis revealed that SMFP₀ exhibited a more negative absolute Zeta potential (−13.05 mV), increased fluorescence intensity (0.020) in its tightly bound extracellular polymeric substances (TB-EPSs), and significantly higher protein (PN, 64.22 mg/L) and polysaccharide (PS, 56.99 mg/L) concentrations compared with the control (p < 0.05). These findings suggest that SMFP₀ possesses physicochemical properties that are conducive to microalgae–fungal aggregation. A scanning electron microscopy (SEM) analysis confirmed that the SA gel network enhanced the system’s stability by strengthening the microalgae–fungal interfacial adhesion and maintaining a porous, light-permeable structure. In practical wastewater treatment, SMFP₀ achieved superior removal rates for COD (84.19%), ammonia nitrogen (95.29%), total nitrogen (89.50%), and total phosphorus (93.46%) compared with non-crosslinked MFPs (p < 0.05). After 9 days of continuous operation (SMFP₉), the pollutant removal efficiencies remained comparable to those observed in the initial stage of the non-crosslinked system, indicating improved structural durability for extended practical application. Full article

Mesoporous silicas of MCM-41 and MCM-48 types were synthesized and modified with copper using the ammonia-driven deposition precipitation (ADP) method, resulting in highly dispersed copper species. Samples with varying copper loadings were thoroughly characterized in terms of their porous structure, metal content, copper species’ aggregation, and the stability of deposited forms under reaction conditions. Copper-modified mesoporous silicas exhibited excellent catalytic performance in the low-temperature NH₃-SCR process. Their activity in NO to NO₂ oxidation suggests that the fast-SCR pathway plays a significant role in NO_x conversion at low temperatures. However, direct ammonia oxidation limited SCR efficiency at higher temperatures. These findings demonstrate the potential of ADP-modified copper–silica catalysts for effective and selective NO_x removal under low-temperature conditions. Full article

With the rapid development of the global aquaculture industry, the issue of effluent pollution from aquaculture has become increasingly severe. Effective management of aquaculture effluent is an urgent requirement for the sustainable development of the aquaculture industry, with a key focus on the efficient removal of nitrogen. Heterotrophic bacteria assimilation technology offers advantages such as high efficiency and resource recovery; however, its application in effluent treatment remains limited. Therefore, this study aimed to identify the optimal carbon source for the heterotrophic bacteria assimilation process and to optimize its operating parameters using response surface methodology (RSM). The results revealed that the sucrose group achieved the highest total ammonia nitrogen (TAN) removal rate of 85.1%, significantly outperforming molasses (77.0%) and glucose (62.9%), with microbial biomass also significantly higher than in the other groups. Metagenomic analysis indicated that sucrose promotes the formation of efficient denitrifying microbial communities by enriching the phylum Bacteroidota and the denitrifying functional bacteria Xanthomarina, thereby significantly enhancing denitrification efficiency. The optimal carbon source was determined to be sucrose. Using the optimal parameters of microbial biomass at 1.7 g/L, a hydraulic retention time of 36 h, and a chemical oxygen demand-to-total nitrogen (COD/TN) ratio of 26, the removal rates of total nitrogen (TN), TAN, and nitrite nitrogen (NO₂⁻-N) exceeded 85%, while the removal rate of nitrate nitrogen (NO₃⁻-N) surpassed 60%. A significant interaction was observed between microbial biomass and hydraulic retention time, which notably affected denitrification efficiency (p < 0.05). This study provides theoretical support for the harmless and resourceful treatment of aquaculture effluent, contributing to the green and sustainable development of the aquaculture industry. Full article

The excessive input of nitrogen and phosphorus pollutants into surface water bodies poses a serious threat to the aquatic ecosystem. As an efficient porous adsorbent material, ceramsite shows remarkable potential in the field of simultaneous nitrogen and phosphorus removal. In this study, Fe₂O₃ catalyzed the decomposition of K₂CO₃ to generate CO and CO₂ gases, leading to the formation of a large number of pore structures in the composite ceramsite. Subsequently, adsorption experiments were conducted on the obtained ceramsite. The regulatory mechanisms of the ceramsite dosage and solution pH on its adsorption performance were revealed. The experiments show that as the ceramsite dosage increased from 2.1 g/L to 9.6 g/L, the adsorption capacities of ammonia–nitrogen and phosphorus decreased from 0.4521 mg/g and 0.4280 mg/g to 0.1430 mg/g and 0.1819 mg/g, respectively, while the removal rates increased to 68.66% and 58.22%, respectively. This indicates that the competition between the utilization efficiency of adsorption sites and the mass-transfer limitation between particles dominates this process. An analysis of the pH effect reveals that the adsorption of ammonia–nitrogen reached a peak at pH = 10 (adsorption capacity of 0.4429 mg/g and removal rate of 81.58%), while the optimal adsorption of phosphorus occurred at pH = 7 (adsorption capacity of 0.3446 mg/g and removal rate of 86.40%). This phenomenon is closely related to the interaction between the existing forms of pollutants and the surface charge. Kinetic and thermodynamic studies show that the pseudo-second-order kinetic model (R² > 0.99) and the Langmuir isothermal model can accurately describe the adsorption behavior of the ceramsite for ammonia–nitrogen and phosphorus, confirming that the adsorption is dominated by a monolayer chemical adsorption mechanism. This study explores the dosage–efficiency relationship and pH response mechanism of Fe₂O₃-catalyzed porous ceramsite for nitrogen and phosphorus adsorption, revealing the interface reaction pathway dominated by Fe₂O₃ catalysis and chemical adsorption. It provides theoretical support for the construction of porous ceramsite and the development of an efficient technology system for the synergistic removal of nitrogen and phosphorus. Full article