Search Results (338)

Rhodamine B (RhB) is a typical xanthene-based cationic dye. Its widespread application has brought serious safety and environmental risks. Heterogeneous Fenton systems based on zero-valent iron (Fe⁰) are promising for RhB degradation. However, bare Fe⁰ suffers from severe agglomeration and surface passivation. In this study, alumina with a large pore volume and high specific surface area was employed as a support to enhance Fe⁰ dispersion and stability. The catalyst was prepared via a glucose-assisted carbothermal reduction method, and the formation of Fe⁰ was confirmed by X-ray diffraction and electron microscopy analyses. Under optimal conditions (pH = 3.58, catalyst dosage = 0.8 g·L⁻¹, H₂O₂ = 10 mM), 10 mg·L⁻¹ RhB was completely degraded within 25 min, with a pseudo-first-order rate constant of 0.432 min⁻¹. This exhibits a faster degradation rate and efficiency advantage. Radical quenching experiments indicated that hydroxyl radicals (•OH) were the dominant reactive species, while singlet oxygen (¹O₂) also contributed to the degradation process. Two primary degradation pathways, including N-deethylation and hydroxylation, were identified. The catalyst showed moderate reusability with slight deactivation after repeated cycles. This study demonstrates that tailoring the pore structure of alumina supports is an effective strategy to enhance Fe⁰ dispersion, mass transfer, and catalytic performance in heterogeneous Fenton systems. Full article

Biogenically recovered mixed metal(loid) sulfides (BPS) obtained from metallurgical effluents were evaluated as sustainable photocatalysts for the solar-driven degradation of Rhodamine B (RhB). The material, recovered using biogenic sulfide produced by sulfate-reducing bacteria in an upflow anaerobic sludge bed reactor, was mainly composed of Sb₂S₃ and Bi-containing sulfide phases and exhibited a fibrous morphology and a narrow direct band gap of 1.306 eV. Under solar irradiation, BPS achieved RhB degradation efficiencies above 98% under the evaluated conditions (0.8 g L⁻¹ catalyst and 5 mg L⁻¹ dye), consistently outperforming reagent-grade Sb₂S₃. Photocatalytic degradation followed pseudo-first-order kinetics (R² > 0.90), and the apparent reaction rate constant was more than five times higher than that of the reference material under the best-performing conditions. A preliminary reusability assessment and post-reaction characterization after three photocatalytic cycles revealed no significant morphological or compositional changes in BPS. These results demonstrate that waste-derived metal(loid) sulfides recovered through a biogenic process can serve as effective solar photocatalysts, highlighting a promising circular-economy strategy for transforming metallurgical residues into value-added materials for water remediation. Full article

The pressing issues of organic pollutants contamination of aquatic ecosystems challenges current research. Herein, we prepared three melamine-based POFs, to remove organic dyes from water. Melamine was polymerized with 1,4-dibromobutane (POF-1,4), terephthalaldehyde (POF-TerA) and trimesic acid (POF-TriA), obtaining POFs of different structural order degree and aromaticity. POFs were characterized using FT-IR spectroscopy, thermal gravimetric analysis, BET, powder X-ray diffraction and scanning electron microscopy. They were employed to remove cationic (Rhodamine B, RhB and Methylene Blue, MB) and anionic dyes (Methyl Orange, MO and Eosin Yellow, EY), using UV-vis investigation. The adsorption process was studied from the kinetic and thermodynamic points of view and reusing the best adsorbent was also considered. Data collected evidence that adsorption capacity depends on the POF structure, with maximum adsorption capacity, according to Langmuir isotherm model, of 329 mg/g for POF-1,4/MO and 472 mg/g for POF-TerA/RhB. Interactions involved in the adsorption were also elucidated. Comparison with reported data demonstrates that our materials show comparable performance to some previously reported systems. Furthermore, POF-TriA, is effective for dye mixtures and reusable three times without performance loss, after washing with methanol, avoiding harsh acidic/basic treatments. Results obtained systematically relate the adsorption efficiency to structural features of melamine-based POFs, representing useful support in designing such materials to remove selected classes of contaminants. Full article

MgCr₂O₄ nanospinel samples were synthesized using a modified Pechini method, followed by controlled calcination. The resulting materials were evaluated in terms of crystal structure, particle morphology, and optical and electronic properties. Their oxidative activity towards the degradation of organic dyes was investigated via photocatalysis, Fenton-like, and photon-Fenton-like processes. Various analytical techniques were employed to characterize the samples, including X-ray diffraction (XRD) with Rietveld refinements, infrared (IR) spectroscopy, UV–Vis spectroscopy, colorimetry, and transmission and high-resolution transmission electron microscopy (TEM/HRTEM). Structural characterization revealed that MgCr₂O₄ crystallized after calcination at 600 °C, and Rietveld refinements confirmed cubic Fd-3m symmetry. IR spectra confirmed the short-range order through the presence of vibrational modes assigned to CrO₆^2- octahedra. UV–Vis spectroscopy indicated mixed Cr valences (Cr³+/Cr⁶+) for samples calcined at temperatures below 900 °C, with Cr⁶+ eliminated at higher temperatures, confirmed by electron paramagnetic resonance (EPR) spectroscopy. This suggests that an oxidation reaction occurred due to oxygen vacancies in the lattice. Optical bandgap (Eg) increased with temperature. Samples calcined at low temperatures were dark green and became more saturated at temperatures above 900 °C, suggesting photoresponse to visible light, as indicated by the Eg values. The oxidative activity of the nanospinels in degrading the dyes methylene blue (MB) and rhodamine B (RhB) under visible light depended on the nature of the dye, the catalyst concentration, and the use of H₂O₂ in the process to improve the formation of hydroxyl radicals (•OH), as confirmed by photohydroxylation of terephthalic acid (TA). The highest degradation rate was observed in the photo-Fenton-like process, with 96% and 97% degradation of RhB and MB dyes in 60 min, reaching a kinetic rate constant (${\mathit{K}}_{app}$) of 0.055 min⁻¹ and 0.051 min⁻¹, respectively. This study highlights the importance of controlling various parameters to promote the formation of reactive oxygen species (ROS) required for oxidative degradation by nanospinels. Full article

In this work, monodisperse carbon microspheres with an average diameter of approximately 900 nm were successfully synthesized via a hydrothermal method. To further tailor their surface properties, the layer-by-layer (LbL) self-assembly technique was employed, where the cationic polyelectrolyte poly(diallyldimethylammonium chloride) (PDDA) and the anionic polyelectrolyte poly(styrene sulfonate) (PSS) were alternately deposited on the microsphere surface, forming two and four bilayer assemblies, respectively. The resulting composite microspheres exhibited remarkable adsorption performance toward representative dyes in water solution, such as rhodamine B (RhB) and methylene blue (MB). Experimental results demonstrated that the incorporation of a single bilayer significantly reduced the specific surface area but introduced additional active adsorption sites, thereby enhancing dye removal efficiency. However, when the number of bilayers was further increased to two, partial pore coverage and blockage occurred, leading to a reduced surface area and consequently diminished adsorption capacity. These findings highlight that in LbL surface modification, more layers do not necessarily yield better performance, but rather an optimal assembly thickness exists. This insight provides valuable guidance for the rational design of advanced adsorbent materials for wastewater treatment. Full article

This paper reports the controlled synthesis of ZrO₂ nanocrystals via a peroxide-assisted hydrothermal (HT) route at 120 °C, with processing times ranging from 12 to 72 h, and investigates the correlation between structural evolution, defect chemistry, and functional properties. X-ray diffraction (XRD) combined with Rietveld refinement confirmed the formation of a monophasic monoclinic structure with high structural reliability. Microstructural analysis revealed progressive crystallite growth and lattice ordering with increasing reaction time, accompanied by subtle distortions in local coordination environments. Micro-Raman spectroscopy indicated improved medium-range structural organization at longer synthesis durations, while transmission electron microscopy showed quasi-spherical and nanorod-like aggregates formed through oriented attachment, with particle sizes of 6–9 nm. Optical investigations using diffuse reflectance spectroscopy revealed band gap energies of 3.45–3.65 eV, attributed to defect-induced intermediate electronic states associated primarily with oxygen vacancies. A comprehensive photoluminescence (PL) analysis suggests that the observed emission arises from defect-mediated recombination pathways involving localized states within the band gap, modulated by the interplay between structural order and residual defects. The role of hydrogen peroxide is discussed in terms of regulating oxygen vacancy concentration, promoting structural stabilization while preserving functional defect states. The results demonstrate that precise control of HT processing time enables tuning of structural disorder, defect density, optical response, and the enhanced photocatalytic performance of ZrO₂ toward RhB dye degradation, highlighting its potential for optoelectronic applications. Full article

Ternary heterojunction photocatalysts enhance the separation and transport of photogenerated charge carriers, thereby boosting their redox activity for use in environmental and sustainable energy applications. This study focuses on the synthesis of a TiO₂/Bi₂O₃/g-C₃N₄ heterojunction composite via a ceramic method with TiO₂ loadings of 80%, 85%, and 90% (denoted 80T-BC, 85T-BC, and 90T-BC, respectively) to investigate structure–property–performance relationships in photocatalytic dye degradation. The structural, optical, and morphological properties of the synthesised materials were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance UV–Vis spectroscopy (DRS). The photocatalytic performance was evaluated by measuring the degradation of Rhodamine B under visible light irradiation. Under optimised conditions (pH 6, initial RhB concentration of 5 mg/L, and a reaction time of 120 min), a degradation rate of 99% was achieved. Furthermore, the semiconductor demonstrated significant antibacterial activity against both Gram-negative (Pseudomonas aeruginosa) and Gram-positive (Staphylococcus aureus) bacteria. This study presents a promising strategy for modifying TiO₂-based semiconductors by incorporating different metal oxides. The formation of the resulting heterojunction significantly enhances photocatalytic efficiency, demonstrating strong potential for practical environmental remediation. Full article

In this study, a polyvinyl alcohol/carboxymethyl chitosan (PVA/CCTS) hydrogel was synthesized via free radical polymerization and employed for the adsorption of Rhodamine B (RhB) from aqueous solution. The hydrogel was systematically characterized by FTIR, SEM, XPS, and BET analyses, confirming its interconnected porous network and functional group composition. Under optimized conditions (adsorbent dosage = 0.1 g, pH = 6, RhB concentration = 65 mg·L⁻¹, and T = 298.15 ± 2 K), the maximum adsorption capacity reached 15.88 mg·g⁻¹. Kinetic analysis showed that the pseudo-second-order model best described the adsorption behavior under optimal conditions, indicating that the uptake of RhB is governed by multiple interaction mechanisms rather than simple physisorption alone. The equilibrium data were best fitted by the Freundlich isotherm (R² = 0.976), indicating surface heterogeneity of the hydrogel. Thermodynamic evaluation revealed an endothermic (ΔH = 28.38 ± 4.40 kJ·mol⁻¹), with adsorption efficiency improving at elevated temperatures. The hydrogel retained appreciable adsorption capacity after three adsorption–desorption cycles (5.78 mg·g⁻¹ at the third cycle). Density functional theory (DFT) calculations identified -COOH and -NH₂ groups as the primary active sites, and molecular electrostatic potential analysis confirmed that electrostatic interactions between the negatively charged hydrogel surface and cationic RhB drive the initial adsorption. Molecular dynamics (MD) simulations over 100 ns further demonstrated that van der Waals forces constitute the dominant driving force, supplemented by electrostatic interactions and hydrogen bonding, with the hydrogel’s cross-linked network stabilizing adsorbed RhB molecules. The integrated experimental computational approach provides a comprehensive mechanistic understanding of RhB adsorption on PVA/CCTS hydrogel, offering guidance for the rational design of polysaccharide-based adsorbents for dye-contaminated wastewater treatment. Full article

Manganese dioxide (MnO₂) modified biochar catalysts derived from biomass and waste polymer feedstocks were synthesized and evaluated as heterogeneous Fenton-like catalysts for solar-driven degradation of Rhodamine B (RhB) in aqueous systems. Biochars produced from maple wood and plastic waste (high-density polyethylene) provided porous carbon matrices with oxygen-rich surface functionalities that enabled effective MnO₂ loading and catalytic activity. Photocatalytic experiments conducted under real sunlight using a solar-collector reactor demonstrated faster RhB degradation compared to a conventional ultraviolet (UV) system, confirming the advantage of solar-driven operation. Complete RhB removal was achieved at initial concentrations of 100–300 ppm, whereas higher dye concentrations (500 ppm) exceeded the catalytic capacity within the tested reaction time. Kinetic analysis revealed catalyst-dependent reaction behaviors, indicating that degradation pathways were strongly influenced by the biopolymer-derived carbon structure and MnO₂ dispersion. Degradation efficiency was correlated with solar irradiance and reactor temperature, with higher UV index conditions enhancing catalytic performance. Reusability tests showed that the catalysts remained active over multiple cycles, although gradual decreases in reaction rates and catalyst recovery were observed. These results demonstrate the potential of biopolymer-derived carbon materials as effective solar-driven catalysts for wastewater treatment applications. Full article

The widespread presence of stable and hazardous organic contaminants, such as synthetic dyes, in industrial effluents necessitates the development of resilient treatment strategies capable of achieving efficient degradation and decolorization of dye pollutants. Conventional treatment processes often fail to remove such recalcitrant compounds, prompting growing interest in integrated advanced systems. Photocatalytic membranes represent a promising solution due to the synergistic combination of physical separation and catalytic degradation. In this study, zinc oxide (ZnO) thin films were deposited by spin coating onto smectite–zeolite ceramic membranes (MS10/Z90), applying one (M1), two (M2), and three (M3) successive coating layers to control catalyst thickness. SEM analysis confirmed that increasing the number of layers resulted in a thicker and more homogeneous ZnO coating, while XRD revealed enhanced crystallinity and larger crystallite size. Water permeability decreased progressively from 623 L·h⁻¹·m⁻²·bar⁻¹ for the uncoated membrane to 506, 439, and 350 L·h⁻¹·m⁻²·bar⁻¹ for M1, M2, and M3, respectively. Photocatalytic performance was evaluated using Rhodamine B (RhB) (10 mg·L⁻¹) under UV irradiation (365 nm, 18 W) for 180 min, achieving degradation efficiencies of 83.0%, 94.6%, and 99.1% for M1, M2, and M3, respectively. The degradation kinetics followed a pseudo-first-order model, with rate constants increasing with catalyst layer thickness. Free radical scavenging assays confirmed that hydroxyl radicals (•OH) were the primary reactive species responsible for RhB degradation. These findings highlight the critical influence of ZnO layer thickness and mass transfer on photocatalytic performance, demonstrating the potential of ZnO-coated ceramic membranes for efficient pollutant degradation and in situ photocatalytic regeneration. Permeability measurements after photocatalytic treatment confirmed effective flux recovery, supporting the operational durability of the developed membranes. Full article

Metal–organic frameworks (MOFs) are unique microporous materials being explored for a wide range of applications. Their porosity and high surface areas can readily be exploited for guest–host interactions, separations, and photochemical catalysis, but many suffer from poor charge separation and fast electron–hole recombination. Introducing structural defects, such as missing linkers or metal nodes, can create unsaturated metal sites and alter band structure, conductivity, and light absorption, improving photocatalytic performance. UiO-66-NH₂ and MIL-125-NH₂ are water-stable, visible-light-absorbing MOFs well suited for photocatalytic degradation of organic dyes. In this work, the influence of defect engineering on photocatalytic properties of MOFs was investigated using formic and acetic acid modulators with UiO-66-NH₂ and variable temperature with MIL-125-NH₂ during synthesis. The resulting materials were characterized by XRD, FTIR and SEM/EDS. Defect states were tracked using N₂ adsorption/BET analysis and UV–Vis spectroscopy. Photocatalytic activity was evaluated by monitoring Rhodamine B (RhB) degradation in aqueous solution under simulated solar irradiation. It was found that increased temperature beyond 120 °C during synthesis promotes mesopore formation and decreases the bandgap in MIL-125-NH₂, resulting in a more photoactive material. Defective MIL-125-NH₂ synthesized at 150 °C showed the most defects and proved to be the best photocatalyst investigated in this study. Formic acid modulation in UiO-66-NH₂ generated smaller crystallites that slightly increased the bandgap; however, the surface area decreased proportionally with the amount of formic acid used. The decreased surface area and observed enhancement in photocatalytic degradation of RhB suggest that formic acid introduces defects into the UiO-66-NH₂ framework that enhance photocatalytic properties. UiO-66-NH₂ treated with acetic acid resulted in larger crystals, increased bandgaps, and increased surface areas, suggesting that acetic acid simply modulates growth rather than imparting defects to the framework. Full article

The degradation of aquatic pollutants using eco-friendly and non-toxic photocatalytic materials is a pivotal strategy for water pollution remediation. However, single-component photocatalysts typically suffer from low photocatalytic efficiency due to limited light absorption spectra and rapid recombination of photogenerated charge carriers. This study reports a novel and facile one-step mixing strategy for realizing triple synergistic modifications: heterostructured composite construction, specific surface area regulation, and efficient photogenerated electron–hole pair separation of Bi₂MoO₆ (BMO) via composite enhancement with low-cost and intrinsically green g-C₃N₄ (CN), which avoids the high cost, complex processes, and potential pollution risks of precious metal/heavy metal modification for BMO. Under visible-light irradiation, the BMO composite modified with 15 wt% CN achieved a dye removal rate of 85.1% within 60 min, representing a 1.6-fold enhancement in photocatalytic performance compared with that achieved using pristine BMO. We further clarify the unique photocatalytic mechanism of the CN/BMO heterojunction via radical quenching experiments, identifying photogenerated holes (h⁺) and superoxide radicals (·O₂⁻) as the dominant active species for Rhodamine B (RhB) degradation. This study systematically demonstrates a scalable photocatalyst preparation method that integrates controllable specific surface area, rational heterostructure construction, and simple operation, and we provide an in-depth investigation into the photocatalytic reaction process and underlying synergistic enhancement mechanism. The proposed non-metallic modification route provides a new theoretical and experimental basis for the design of high-efficiency BMO-based photocatalysts, and the as-prepared CN/BMO composite holds great potential for practical application in sustainable solar-driven water purification. Full article

The biochars obtained by pyrolyzing tomato stems at temperatures of 400, 500, 600, and 700 °C were characterized, and their ability to absorb anionic (Direct Orange 26, DO26) and cationic (Rhodamine B, RhB) dyes from aqueous solutions was investigated. The effects of solution pH and ionic strength were studied. It was found that the adsorption process of both dyes was pH-dependent, but no effect of ionic strength was observed. The kinetics of dye adsorption on biochars were well described by the pseudo-second-order model. The equilibrium adsorption data were analyzed using the Freundlich, Langmuir, and Temkin isotherms. All three equations described dye adsorption on biochars quite well, although a slightly better fit was observed for the Freundlich model. The maximum adsorption capacities of BCs ranged from 54.44 mg/g (BC400) to 108.1 mg/g (BC700) for DO26 and from 4.483 mg/g (BC700) to 8.887 mg/g (BC400) for RhB. The study reveals that biochars derived from tomato stems can be used as efficient, low-cost adsorbents for the removal of anionic and cationic dyes from water. Full article

A highly efficient pyro-catalytic system based on a g-C₃N₄/ZnO composite has been developed for dye degradation under near-room-temperature thermal cycling (25–60 °C). This system integrates pyroelectric charge generation with electrochemical redox reactions. The g-C₃N₄/ZnO for pyro-catalytic Rhodamine B (RhB) dye decomposition with 95.6% efficiency in the dark, whereas pristine g-C₃N₄ reached only approximately 60.1% under identical conditions. The degradation mechanism is primarily driven by the in situ generation of superoxide (•O₂⁻) and hydroxyl (•OH) radicals, as verified by radical quenching experiments. The formation of the composite facilitates the efficient spatial separation of pyroelectric-induced charges, thereby endowing g-C₃N₄/ZnO with a significantly enhanced pyro-catalytic performance compared to g-C₃N₄ alone. This study demonstrates the promising application of g-C₃N₄/ZnO as a high-performance pyro-catalyst under mild thermal conditions, offering a sustainable and light-independent strategy for wastewater treatment by utilizing ambient temperature fluctuations. Full article

Hydrogel fluorescent microspheres function as versatile tracers with applications spanning across biomedicine, complex plasma systems, hydrodynamics, and drug delivery. However, the controlled release of fluorescent material in hydrogel microspheres is challenging to achieve. The fluorescent hydrogel microsphere (namely poly(ethylene glycol) diacrylate@rhodamine B-tannic acid, PEGDA@RhB-TA) was fabricated by incorporating tannic acid and RhB into PEGDA microspheres. The stable encapsulation and responsive release of RhB can be achieved by leveraging the non-covalent interactions between TA and RhB. RhB was stably encapsulated within PEGDA microspheres through noncovalent interactions (hydrophobic interactions, hydrogen bonding, π–π, and ion–π interactions) between RhB and TA. Both molecular dynamics simulations by GROMACS and experimental results confirmed the noncovalent binding mechanisms between RhB and TA. The microspheres retained RhB following 24 h immersion in a highly concentrated salt solution (1 M NaCl) and exhibited minimal RhB release (7.1%) under heating at 80 °C for 24 h. However, PEGDA@RhB-TA microspheres underwent rapid RhB release in a 50% v/v ethanol–water solution, liberating 73% of the encapsulated dye within 24 h. TA within the PEGDA@RhB-TA microsphere acts as a molecular lock by forming non-covalent interactions with RhB, significantly enhancing the stability of encapsulated RhB, and enabling the responsive release of RhB under specific conditions. Upon introduction into a microfluidic chip, PEGDA@RhB-TA microspheres enable the calculation of flow velocity through position tracking using high-speed camera imaging and fluorescence microscopy. These microspheres overcome the dual challenges of tracer stability and controlled release, making them suitable for fluid tracing and measuring flow rates. Full article