Search Results (43)

This article comprehensively reviews the tribological behavior of a Ti-6Al-4V alloy manufactured via electron beam powder bed fusion (EB-PBF), an additive manufacturing process for aerospace and biomedical applications. EB-PBF Ti-6Al-4V demonstrates wear resistance that is superior or comparable to conventional Ti-6Al-4V. The reported average friction coefficient ranges between ~0.22 and ~0.75 during sliding wear in dry and lubricated conditions against metallic and ceramic counterparts when loading 1–50 N under varied surface and heat treatment conditions, and between 1.29 and 2.2 during fretting wear against EB-PBF Ti-6Al-4V itself. The corresponding average specific wear rates show a broad range between ~8.20 × 10⁻⁵ mm³/Nm and ~1.30 × 10⁻³ mm³/Nm during sliding wear. Lubrication reduces the wear rates and/or the friction coefficient. Wear resistance can be improved via machining and heat treatment. Wear anisotropy is reported and primarily attributed to microhardness variations, which can be mitigated through lubrication and post-processing. The effects of applied load and frequency on EB-PBF Ti-6Al-4V are also discussed. The wear resistance at elevated temperatures shows a mixed trend that depends on the counterpart material and the testing methods. Wear mechanisms involve oxide tribo-layer formation, abrasive wear, and adhesive wear. Current limitations, future research directions, and a standardization framework are also discussed. Full article

Powder bed fusion of copper has been extensively investigated using both laser-based (PBF-LB/M) and electron beam-based (PBF-EB/M) additive manufacturing technologies. Each technique offers unique benefits as well as specific limitations. Near-infrared (NIR) laser-based LPBF is widely accessible; however, the high reflectivity of copper limits energy absorption, thereby resulting in a narrow processing window. Although optimized parameters can yield relative densities above 97%, issues such as keyhole porosity, incomplete melting, and anisotropy remain concerns. Green lasers, with higher absorptivity in copper, offer broader process windows and enable more consistent fabrication of high-density parts with superior electrical conductivity, often reaching or exceeding 99% relative density and 100% International Annealed Copper Standard (IACS). Mechanical properties, including tensile and yield strength, are also improved, though challenges remain in surface finish and geometrical resolution. In contrast, Electron Beam Powder Bed Fusion (EB-PBF) uses high-energy electron beams in a vacuum, eliminating oxidation and leveraging copper’s high conductivity to achieve high energy absorption at lower volumetric energy densities (~80 J/mm³). This results in consistently high relative densities (>99.5%) and excellent electrical and thermal conductivity, with additional benefits including faster scanning speeds and in situ monitoring capabilities. However, EB-PBF processes in general face their own limitations, such as surface roughness and powder smoking. This paper provides a comprehensive review of the current state of laser-based (PBF-LB/M) and electron beam-based (PBF-EB/M) powder bed fusion processes for the additive manufacturing of copper, summarizing key trends, material properties, and process innovations. Both approaches continue to evolve, with ongoing research aimed at refining these technologies to enable the reliable and efficient additive manufacturing of high-performance copper components. Full article

This study investigates the anodization behavior and surface modification of Ti6Al4V (Ti64) alloy components fabricated via electron beam powder bed fusion (EB-PBF), aiming to enhance their performance in biomedical applications. Ti64 samples were manufactured using optimized EB-PBF parameters to produce a uniform microstructure and surface quality. Electrochemical anodization at 40 V and 60 V for 2 h generated self-organized TiO₂ nanotube layers, followed by a heat treatment at 550 °C to improve crystallinity while preserving the nanotube morphology. Characterization using scanning electron microscopy (SEM) and atomic force microscopy (AFM) revealed that a lower voltage produced uniform, compact nanotubes with moderate roughness and higher hardness, whereas a higher voltage generated thicker, less ordered nanotubes with larger diameters, increased roughness, and slightly reduced mechanical performance. X-ray diffraction (XRD) confirmed the presence of anatase TiO₂ phases, and energy-dispersive spectroscopy (EDS) analysis revealed a homogeneous distribution of Ti and O. Mechanical testing via nanoindentation and nanoscratch techniques demonstrated superior hardness and adhesion in nanotubes formed at lower voltage due to their compact structure. Electrochemical measurements indicated significantly enhanced corrosion resistance in anodized samples, attributed to the dense and chemically stable TiO₂ layer that acts as a barrier to aggressive ions and reduces active corrosion sites. In vitro bioactivity analysis further confirmed improved apatite formation on anodized surfaces. These results demonstrate the synergistic potential of EB-PBF and controlled anodization for modifying the surface properties of Ti64 implants, leading to improved mechanical behavior, corrosion resistance, and biological performance suitable for biomedical applications. Full article

The ability to control process parameters over time and build space in electron beam powder bed fusion (PBF-EB) opens up unprecedented opportunities to tailor the process and use materials of a different nature in the same build. The present investigation explored the various methods used to adapt the PBF-EB process for the production of functionally graded materials (FGMs). In this way, two pre-alloyed powders—a stainless steel (SS) powder and a highly alloyed cold work tool steel (TS) powder—were combined during processing in an S20 Arcam machine. Feasibility experiments were first carried out in a downscaled build setup, in which a single powder container was installed on top of the rake system. In the container, one powder was placed on top of the other (SS/TS) so that the gradient materials were produced as the powders were spread and intermixed during the build. The process was later scaled up to an industrial machine setup, where a similar approach was implemented using two configurations of powder disposal: SS/SS + TS/TS and TS/TS + SS/SS. Each configuration had an intermediate layer of powder blend. The FGMs obtained were characterized in terms of their microstructure and local and macromechanical properties. For the microstructural analysis, optical microscopy, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX) were performed on the polished cross-sections. This provided evidence of gradual microstructural and compositional transitions in the samples, with a shift from SS to TS and vice versa. Nanoindentation experiments confirmed that there was a consequent gradient in the hardness, stiffness, and wear ratio from the softer and ductile SS to the harder and stiff TS. Scratch experiments revealed gradual evolution in the sliding wear behavior of the printed materials. A “progressive spring” and a “hardness-tailored punching tool” were fabricated as demonstrators. The results obtained demonstrate the great potential to gradually tailor the composition, microstructure, mechanical properties, and wear resistance by combining different powders, and they suggest that any PBF-EB system can be repurposed to build gradient materials without hardware modification. Potential applications include the tooling industry, where hard and wear-resistant materials are needed for the surfaces of tools, with tougher and more ductile materials used in the cores of tools. Full article

In additive manufacturing, controlling hot cracking in non-weldable nickel-based superalloys poses a significant challenge for forming complex components. This study introduces a multiple preheating process for the forming surface in electron beam powder bed fusion (EB-PBF), employing a dual-band infrared surface temperature measurement technique instead of the conventional base plate thermocouple method. This new approach reduces the temperature drop during forming, decreasing surface cooling by 28.6% compared to traditional methods. Additionally, the precipitation of carbides and borides is reduced by 38.5% and 80.1%, respectively, lowering the sensitivity to liquefaction cracking. This technique enables crack-free forming at a lower powder bed preheating temperature (1000 °C), thereby improving the powder recycling rate by minimizing powder sintering. Microstructural analysis confirms that this method reduces low-melting eutectic formation and alleviates liquefaction cracking at high-angle grain boundaries caused by thermal cycling. Consequently, crack-free IN738 specimens with high-temperature durability were successfully achieved, providing a promising approach for the EB-PBF fabrication of crack-resistant IN738 components. Full article

Inconel 718 is a widely popular aerospace superalloy known for its high-temperature performance and resistance to oxidation, creep, and corrosion. Traditional manufacturing methods, like casting and powder metallurgy, face challenges with intricate shapes that can result in porosity and uniformity issues. On the other hand, Additive Manufacturing (AM) techniques such as Powder Bed Fusion (PBF) and Direct Energy Deposition (DED) can allow the creation of intricate single-part components to reduce weight and maintain structural integrity. However, AM parts often exhibit directional solidification, leading to anisotropic properties and potential crack propagation sites. To address this, post-processing treatments like HIP and heat treatment are necessary. This study explores the effects of the raster and stochastic spot melt scanning strategies on the microstructural and mechanical properties of IN718 parts fabricated using Electron Beam Powder Bed Fusion (EB-PBF). This research demonstrates that raster scanning produces columnar grains with higher mean aspect ratios. Stochastic spot melt scanning facilitates the formation of equiaxed grains, which enhances microstructural refinement and lowers anisotropy. The highest microstructural values were recorded in the raster-produced columnar grain structure. Conversely, the stochastic melt-produced transition from columnar to equiaxed grain structure demonstrated increased hardness with decreasing grain size; however, the hardness of the smallest equiaxed grain structure was slightly less than that of the columnar grain structure. These findings underscore the vital importance of scanning strategies in optimizing the EB-PBF process to enhance material properties. Full article

The use of an electron beam (EB) as a heating source in EB-based powder bed fusion (PBF-EB) has several limitations, such as reduced powder recyclability, short machine service intervals, difficulties with heating large areas and the limited processability of charge-sensitive powders. Near-infrared (NIR) heating was recently introduced as a feasible replacement and/or complement to EB heating in PBF-EB. This work further investigates the feasibility of using NIR to eliminate the need for a build platform as well as to enable easier repairing of parts in PBF-EB. NIR-assisted Ti-6Al-4V builds were successfully carried out by starting from a loose powder bed without using a build platform. The results do not only confirm that it is possible to eliminate the build platform by the aid of NIR, but also that it can be beneficial for the process cleanliness and improve the surface quality of built parts. Furthermore, a 430 stainless-steel (SS) component could be repaired by positioning it in a loose 316L SS powder bed using a fully NIR-heated PBF-EB process. Full article

Laser Powder Directed Energy Deposition (LP-DED) can produce thin-wall features on the order of 1 mm. These features are essential for large structures operating in extreme environments such as regeneratively cooled nozzles and heat exchangers, which often make use of refractory metals. In this work, the mechanical behavior of LP-DED C103 was investigated via quasi-static tensile testing and low cycle fatigue (LCF) testing. The effects of vacuum stress relief (SR) and hot isostatic pressing (HIP) heat treatments were investigated for specimens in the vertical and horizontal build orientations during tensile testing. The AB and SR properties were lower than literature values for wrought and laser powder bed fusion (L-PBF) bulk components but higher than electron beam powder bed fusion (EB-PBF). The application of a HIP cycle improved strength by 7% and ductility by 27% past the initial as-built condition. Fracture images reveal that interlayer stress concentration sites are responsible for fracture in specimens in the vertical orientation. Meanwhile, fracture in the horizontal specimens mainly propagates at a slanted angle typical of plane stress conditions. The LCF results show cycles to failure ranging from 100 cycles to 8000 cycles for max strain levels of 2% and 0.5%, respectively. Fractography on the fatigue specimens reveals an increasing propagation zone as max strain levels are increased. The impact of these findings and future work are discussed in detail. Full article

A high-alloy (Cr-Mo-V) cold-work tool steel was manufactured by laser powder-bed fusion (PBF-LB) without preheating and by electron-beam powder-bed fusion (PBF-EB) with the build temperature set at 850 °C. The solidification rates, cooling, and thermal cycles that the material was subjected to during manufacturing were different in the laser powder-bed fusion than electron-beam powder-bed fusion, which resulted in very different microstructures and properties. During the solidification of the PBF-LB steel, a cellular–dendritic structure was formed. The primary cell size was 0.28–0.32 µm, corresponding to a solidification rate of 2.0–2.5 × 10⁶ °C/s. No coarse primary carbides were observed in the microstructure. Further rapid cooling resulted in the formation of a martensitic microstructure with high amounts of retained austenite. The high-retained austenite explained the low hardness of 597 ± 38 HV. Upon solidification of the PBF-EB tool steel, dendrites with well-developed secondary arms and a carbide network in the interdendritic space were formed. Secondary dendrite arm spacing was in the range of 1.49–3.10 µm, which corresponds to solidification rates of 0.5–3.8 × 10⁴ °C/s. Cooling after manufacturing resulted in the formation of a bainite needle-like microstructure within the dendrites with a final hardness of 701 ± 17 HV. These findings provide a background for the selection of a manufacturing method and the development of the post-treatment of a steel to obtain a desirable final microstructure, which ensures that the final tool’s performance is up to specification. Full article

This review explores the critical role of powder quality in metal 3D printing and the importance of effective powder recycling strategies. It covers various metal 3D printing technologies, in particular Selective Laser Melting, Electron Beam Melting, Direct Energy Deposition, and Binder Jetting, and analyzes the impact of powder characteristics on the final part properties. This review highlights key challenges associated with powder recycling, including maintaining consistent particle size and shape, managing contamination, and mitigating degradation effects from repeated use, such as wear, fragmentation, and oxidation. Furthermore, it explores various recycling techniques, such as sieving, blending, plasma spheroidization, and powder conditioning, emphasizing their role in restoring powder quality and enabling reuse. Full article

Titanium parts fabricated by additive manufacturing, i.e., laser or electron beam-powder bed fusion (L- or EB-PBF), usually exhibit columnar grain structures along the build direction, resulting in both microstructural and mechanical anisotropy. Post-heat treatments are usually used to reduce or eliminate such anisotropy. In this work, Ti-6Al-2Zr-1Mo-1V (TA15) alloy samples were fabricated by L-PBF to investigate the effect of post-heat treatment and load direction on the dynamic response of the samples. Post-heat treatments included single-step annealing at 800 °C (HT) and a hot isotropic press (HIP). The as-built and heat-treated samples were dynamically compressed using a split Hopkinson pressure bar at a strain rate of 3000 s⁻¹ along the horizontal and vertical directions paralleled to the load direction. The microstructural observation revealed that the as-built TA15 sample exhibited columnar grains with fine martensite inside. The HT sample exhibited a fine lamellar structure, whereas the HIP sample exhibited a coarse lamellar structure. The dynamic compression results showed that post-heat treatment at 800 °C led to reduced flow stress but enhanced uniform plastic strain and damage absorption work. However, the HIP samples exhibited both higher stress, uniform plastic strain, and damage absorption work owing to the microstructure coarsening. Additionally, the load direction had a subtle influence on the flow stress, indicating the negligible anisotropy of flow stress in the samples. However, there was more significant anisotropy of the uniform plastic strain and damage absorption. The samples had a higher load-bearing capacity when dynamically compressed perpendicular to the build direction. Full article

This study investigates the potential benefits of integrating coarser particle size distributions (PSDs) of 45–106 µm into laser-based powder bed fusion of metals (PBF-LB/M), aiming to reduce costs while maintaining quality standards. Despite the considerable advantages of PBF-LB/M for producing intricate geometries with high precision, the high cost of metal powders remains a barrier to its widespread adoption. By exploring the use of coarser PSDs, particularly from electron beam-based powder bed fusion of metals (PBF-EB/M), significant cost-saving opportunities are identified. Through a comprehensive powder characterization, process analysis, and mechanical property evaluation, this study demonstrates that PBF-LB/M can effectively utilize coarser powders while achieving comparable mechanical properties as those produced with a 20–53 µm PSD. Adaptations to the process parameters enable the successful processing of coarser powders, maintaining high relative density components with minimal porosity. Additionally, market surveys reveal substantial cost differentials between PBF-LB/M and PBF-EB/M powders, indicating a 40% cost reduction potential for the feedstock material by integrating coarser PSDs into PBF-LB/M. Overall, this study provides valuable insights into the economic and technical feasibility of printing with coarser powders in PBF-LB/M, offering promising avenues for cost reduction without compromising quality, thus enhancing competitiveness and the adoption of the technology in manufacturing applications. Full article

Electron beam–powder bed fusion (PBF-EB) is an additive manufacturing process that utilizes an electron beam as the heat source to enable material fusion. However, the use of a charge-carrying heat source can sometimes result in sudden powder explosions, usually referred to as “Smoke”, which can lead to process instability or termination. This experimental study investigated the initiation and propagation of Smoke using in situ high-speed synchrotron radiography. The results reveal two key mechanisms for Smoke evolution. In the first step, the beam–powder bed interaction creates electrically isolated particles in the atmosphere. Subsequently, these isolated particles get charged either by direct irradiation by the beam or indirectly by back-scattered electrons. These particles are accelerated by electric repulsion, and new particles in the atmosphere are produced when they impinge on the powder bed. This is the onset of the avalanche process known as Smoke. Based on this understanding, the dependence of Smoke on process parameters such as beam returning time, beam diameter, etc., can be rationalized. Full article

This study provides a methodology for exploring the microstructural and mechanical properties of the Haynes^®282^® alloy produced via the Powder Bed Fusion-Electron Beam (PBF-EB) process. Employing 2D Electron Backscatter Diffraction (EBSD) data, we have successfully generated 3D representations of columnar microstructures using the Representative Volume Element (RVE) method. This methodology allowed for the validation of elastic properties through Crystal Elasticity Finite Element (CEFE) computational homogenization, revealing critical insights into the material behavior. This study highlights the importance of accurately representing the grain morphology and crystallographic texture of the material. Our findings demonstrate that created virtual models can predict directional elastic properties with a high level of accuracy, showing a maximum error of only ~5% compared to the experimental results. This precision underscores the potential of our approach for predictive modeling in Additive Manufacturing (AM), specifically for materials with complex, non-homogeneous microstructures. It can be concluded that the results uncover the intricate link between microstructural features and mechanical properties, underscoring both the challenges encountered and the critical need for the accurate representation of grain data, as well as the significance of achieving a balance in EBSD area selection, including the presence of anomalies in strongly textured microstructures. Full article

This study focuses on the surface modification of Ti₆Al₄V scaffolds produced through additive manufacturing using the Powder-Bed Fusion Electron-Beam Melting (PBF-EB) technique. From our perspective, this technique has the potential to enhance implant osseointegration, involving the growth of a layer of titanium dioxide nanotubes (TiO₂) on surfaces through anodic oxidation. Scaffolds with anodized surfaces were characterized, and the formation of a nanoporous and crystalline TiO₂ layer was confirmed. The analysis of cell morphology revealed that cells adhered to the anodized surfaces through their filopodia, which led to proliferation during the initial hours. However, it was observed that the adhesion of Saos-2 cells was lower on anodized scaffolds compared to both built and chemically polished scaffolds throughout the cell culture period. The results obtained here suggest that while anodic oxidation is effective in achieving a nanoporous surface, cell adhesion and interaction were affected by the weak adhesion of cell filopodia to the surface. Thus, combining surface treatment techniques to create micro- and nanopores may be an effective alternative for achieving a favorable cellular response when the objective is to enhance the performance of porous titanium scaffolds in the short term. Full article