Search Results (14)

In this work, conductive polymers, i.e., polyaniline (PANI) and its copolymers with polypyrrole (PPy), polythiophene (PTh), and poly (3,4-ethylenedioxythiophene) (PEDOT) were synthesized following chemical oxidative polymerization methods and used in the construction of supercapacitor devices. These conductive copolymers were characterized by structural (FTIR, XRD), morphological (FESEM), electrochemical (CV and GCD), and impedance spectroscopy studies. The PANI-PPy copolymer showed higher sp. capacitance of 420 F/g and cyclic capacitive retention of 97.8% compared to the other copolymers. Additionally, Tafel extrapolation studies demonstrated that the PANI-PEDOT had the lowest corrosion rate. To further assess performance, asymmetric supercapacitor devices (ASDs) were fabricated using prepared materials. GCD analysis demonstrated that the PANI-PTh//AC device achieved a sp. capacitance of 81 F/g and power density of 550 W/kg, while the PANI-PPy//AC device exhibited a capacitance of 69 F/g. PANI-PTh//AC device shows superior performance over other electrode configurations. Full article

Supercapacitor/pseudocapacitor structures with electrodes and electrolytes based on conductive polymers, but not only, have been analyzed using advanced molecular dynamics simulation techniques. Results indicated in the literature were used to confirm the results obtained for the specific capacitance and energetic performances of the systems. New material classes like Polymer-MXene electrodes ((PANI)/Ti₃C₂, PFDs/Ti₃C₂T_x) present increased capacitance in comparison with simple polymeric composites (PETC or PTh). Combinations of polymers and metallic oxide, like PANI/V₂O₅, present high capacitance, but new variants can provide improved performance. Different techniques, like electrode doping, adding different salts in the electrolyte (gel electrolyte), and using porous electrodes, can also improve performance. Steps for the non-invasive simulation method with HFSS (Ansys) are defined, and the materials are described at the molecular level as well as the interactions between atomic groups. Macroscopic properties of the system are determined (conductivity, specific energy) and represented on parametric graphs. A complex set of parameters is varied in order to optimize the structures through parameter correlation. Different stages of correlation are considered in order to establish the final sample design and improve energetic performance. An increase of about 8–28% can be obtained concerning the specific energy of the supercapacitor. Prediction, design, atypical behavior, and resonance are addressed using this technique. Full article

New materials and the interactions between them are the basis of novel energy storage devices such as supercapacitors and batteries. In recent years, because of the increasing demand for electricity as an energy source, the development of new energy storage materials is among the most actively studied topics. Conductive polymers (CPs), because of their intrinsic electrochemical activity and electrical conductivity, have also been intensively explored. While most of the high capacitance reported in the literature comes from hybrid materials, for example, conductive polymers composed of metal oxides and carbon materials, such as graphene and carbon nanotubes, new chemistry and the 3D structure of conductive polymers remain critical. This comprehensive review focuses on the basic properties of three popular conductive polymers and their composites with carbon materials and metal oxides that have been actively explored as energy storage materials, i.e., polypyrrole (PPy), polyaniline (PANi), and polythiophene (PTh), and various types of electrolytes, including aqueous, organic, quasi-solid, and self-healing electrolytes. Important experimental parameters affecting material property and morphology are also discussed. Electrochemical and analytical techniques frequently employed in material and supercapacitor research are presented. In particular, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) are discussed in detail, including how to extract data from spectra to calculate key parameters. Pros and cons of CP-based supercapacitors are discussed together with their potential applications. Full article

The present work reports the synthesis of indigo-dye-incorporated polyaniline (Indigo-PANI), poly(1-naphthylamine) (Indigo-PNA), poly(o-phenylenediamine) (Indigo-POPD), polypyrrole (Indigo-PPy), and polythiophene (Indigo-PTh) via an ultrasound-assisted method. The synthesized oligomers were characterized using FTIR, UV–visible spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), fluorescence studies, and thermogravimetric analysis (TGA). The experimental data were theoretically compared to analyze the vibrational and electronic spectra via time-dependent density-functional theory (TD-DFT) by applying the Becke, three-parameter, and Lee-Yang-Parr (B3LYP) method with a 6-311G (d,p) basis set. The experimental, theoretical vibrational, and electronic spectra were found to be in close agreement and confirmed the successful incorporation of indigo dye in PANI, PNA, POPD, PPy, and PTh. These studies confirmed that multifunctional oligomers could be synthesized through a facile technique by incorporating dye moieties to enhance their optoelectronic properties, allowing them to be utilized as near-infrared-emitting probes for photodynamic therapy. Full article

The three-layer electrode consisting of the inner, middle, and outer layers of polythiophene (PTh), polyaniline (PANI), and poly(neutral red) (PNR), respectively, was developed, characterized, and tested as a potentiometric sensor for citrates. The spectroscopic and morphological findings based on Raman spectroscopy and scanning electron microscopy, respectively, demonstrated the consecutive formation of individual polymeric layers derived from PTh, PANI, and PNR in the multilayer system. The sharper and narrower peak profiles of PNR in the case of the three-layer system revealed a more organized structure than for the PNR layer alone. The PNR layer in such a novel arrangement shows the highest selectivity towards citrates among the tested carboxylates. Simultaneously, the unwanted influence of the underlying Pt surface is eliminated. The potentiometric characteristics of the proposed potentiometric sensor were examined at the detection of citrates in the real-world samples, compared with results for PNR simple electrode, and corresponded with the reference capillary electrophoresis and literature-based spectrophotometric method. Full article

Advanced conductors (such as conducting and semiconducting polymers) are vital building blocks for modern technologies and biocompatible devices as faster computing and smaller device sizes are demanded. Conjugated conducting and semiconducting polymers (including poly(3,4-ethylenedioxythiophene) (PEDOT), polyaniline (PANI), polythiophene (PTh), and polypyrrole (PPy)) provide the mechanical flexibility required for the next generation of energy and electronic devices. Electrical conductivity, ionic conductivity, and optoelectronic characteristics of advanced conductors are governed by their texture and constituent nanostructures. Thus, precise textural and nanostructural engineering of advanced conjugated conducting and semiconducting polymers provide an outstanding pathway to facilitate their adoption in various technological applications, including but not limited to energy storage and harvesting devices, flexible optoelectronics, bio-functional materials, and wearable electronics. This review article focuses on the basic interconnection among the nanostructure and the characteristics of conjugated conducting and semiconducting polymers. In addition, the application of conjugated conducting and semiconducting polymers in flexible energy devices and the resulting state-of-the-art device performance will be covered. Full article

The purpose of this review article is to outline the extended applications of polyurethane (PU)-based nanocomposites incorporated with conductive polymeric particles as well as to condense an outline on the chemistry and fabrication of polyurethanes (PUs). Additionally, we discuss related research trends of PU-based conducting materials for EMI shielding, sensors, coating, films, and foams, in particular those from the past 10 years. PU is generally an electrical insulator and behaves as a dielectric material. The electrical conductivity of PU is imparted by the addition of metal nanoparticles, and increases with the enhancing aspect ratio and ordering in structure, as happens in the case of conducting polymer fibrils or reduced graphene oxide (rGO). Nanocomposites with good electrical conductivity exhibit noticeable changes based on the remarkable electric properties of nanomaterials such as graphene, RGO, and multi-walled carbon nanotubes (MWCNTs). Recently, conducting polymers, including PANI, PPY, PTh, and their derivatives, have been popularly engaged as incorporated fillers into PU substrates. This review also discusses additional challenges and future-oriented perspectives combined with here-and-now practicableness. Full article

Proper treatment and disposal of industrial pollutants of all kinds are a global issue that presents significant techno-economical challenges. The presence of pollutants such as heavy metal ions (HMIs) and organic dyes (ODs) in wastewater is considered a significant problem owing to their carcinogenic and toxic nature. Additionally, industrial gaseous pollutants (GPs) are considered to be harmful to human health and may cause various environmental issues such as global warming, acid rain, smog and air pollution, etc. Conductive polymer-based nanomaterials have gained significant interest in recent years, compared with ceramics and metal-based nanomaterials. The objective of this review is to provide detailed insights into different conductive polymers (CPs) and their nanocomposites that are used as adsorbents for environmental remediation applications. The dominant types of CPs that are being used as adsorbent materials include polyaniline (PANI), polypyrrole (Ppy), and polythiophene (PTh). The various adsorption mechanisms proposed for the removal of ODs, HMIs, and other GPs by the different CPs are presented, together with their maximum adsorption capacities, experimental conditions, adsorption, and kinetic models reported. Full article

The use of graphene and its derivatives with excellent characteristics such as good electrical and mechanical properties and large specific surface area has gained the attention of researchers. Recently, novel nanocomposite materials based on graphene and conducting polymers including polyaniline (PANi), polypyrrole (PPy), poly (3,4 ethyldioxythiophene) (PEDOT), polythiophene (PTh), and their derivatives have been widely used as active materials in gas sensing due to their unique electrical conductivity, redox property, and good operation at room temperature. Mixing these two materials exhibited better sensing performance compared to pure graphene and conductive polymers. This may be attributed to the large specific surface area of the nanocomposites, and also the synergistic effect between graphene and conducting polymers. A variety of graphene and conducting polymer nanocomposite preparation methods such as in situ polymerization, electropolymerization, solution mixing, self-assembly approach, etc. have been reported and utilization of these nanocomposites as sensing materials has been proven effective in improving the performance of gas sensors. Review of the recent research efforts and developments in the fabrication and application of graphene and conducting polymer nanocomposites for gas sensing is the aim of this review paper. Full article

In this study, a super porous polymeric network prepared from a natural polymer, carboxymethyl cellulose (CMC), was used as a scaffold in the preparation of conductive polymers such as poly(Aniline) (PANi), poly(Pyrrole) (PPy), and poly(Thiophene) (PTh). CMC–conductive polymer composites were characterized by Fourier transform infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA) techniques, and conductivity measurements. The highest conductivity was observed as 4.36 × 10⁻⁴ ± 4.63 × 10⁻⁵ S·cm⁻¹ for CMC–PANi cryogel composite. The changes in conductivity of prepared CMC cryogel and its corresponding PAN, PPy, and PTh composites were tested against HCl and NH₃ vapor. The changes in conductivity values of CMC cryogel upon HCl and NH₃ vapor treatment were found to increase 1.5- and 2-fold, respectively, whereas CMC–PANi composites showed a 143-fold increase in conductivity upon HCl and a 12-fold decrease in conductivity upon NH₃ treatment, suggesting the use of natural polymer–conductive polymer composites as sensor for these gases. Full article

Polyethyleneimine (PEI) cryogels with interconnected superporous morphology were synthesized via the cryopolymerization technique. Then, conductive polymers, poly(Aniline) (PANi), poly(Pyrrole) (PPy), and poly(Thiophene) (PTh) were prepared within these PEI cryogels. Then, the conductive polymer embedding PEI composites’ characterization was carried morphologically using scanning electron microscope (SEM) by means of Fourier Transform Infrared Radiation (FT-IR) spectrometer, and by means of electrical conductivity measurements using an electrometer. Among all the prepared cryogel conductive polymer composites, the highest value in terms of conductivity was determined for PEI/PANi cryogel composites with 4.80 × 10⁻³ S.cm⁻¹. Afterward, to prepare polymeric ionic liquid (PIL) forms of PEI and PEI/PANi composites. To assess the effect of anions on the conductivities of the prepared composites, PEI-based cryogels were anion ex-changed after protonation with HCl by treatment of aqueous solutions of sodium dicyanamide (Na⁺[N(CN)₂]⁻), ammonium hexafluorophosphate (NH₄⁺[PF₆]⁻), sodium tetrafluoroborate (Na⁺[BF₄]⁻), and potassium thiocyanate (K⁺[SCN]⁻), separately. Furthermore, PEI-based cryogel composites and their PIL forms were tested as a sensor for CO₂ gas. The higher conductivity changes were observed on bare PEI cryogel and PEI⁺[BF4]⁻ PIL cryogels with 1000-fold decrease on conductivity upon 240 min CO₂ exposure. The sensitivity and recovery percent of bare PEI and PEI⁺[BF₄]⁻ PIL cryogels were shown almost the same with a two-fold decrease in the presence of 0.009 mole of CO₂ gas, and approximately 30% recovery after the fifth consecutive reuse. Full article

With the urgent requirement for high-performance rechargeable Li-S batteries, besides various carbon materials and metal compounds, lots of conducting polymers have been developed and used as components in Li-S batteries. In this review, the synthesis of polyaniline (PANI), polypyrrole (PPy) and polythiophene (PTh) is introduced briefly. Then, the application progress of the three conducting polymers is summarized according to the function in Li-S batteries, including coating layers, conductive hosts, sulfur-containing compounds, separator modifier/functional interlayer, binder and current collector. Finally, according to the current problems of conducting polymers, some practical strategies and potential research directions are put forward. We expect that this review will provide novel design ideas to develop conducting polymer-containing high-performance Li-S batteries. Full article

Polyaniline (PANI), polypyrrole (Ppy), and polythiophene (PTh) composite nanoparticles with embedded glucose oxidase (GOx) were formed by enzymatic polymerization of corresponding monomers (aniline, pyrrole, and thiophene). The influence of monomers concentration, the pH of solution, and the ratio of enzyme/substrate on the formation of PANI/GOx, Ppy/GOx, and PTh/GOx composite nanoparticles were spectrophotometrically investigated. The highest formation rate of PANI-, Ppy-, and PTh-based nanoparticles with embedded GOx was observed in the sodium acetate buffer solution, pH 6.0. The increase of optical absorbance at λ_max = 440 nm, λ_max = 460 nm, and λ_max = 450 nm was exploited for the monitoring of PANI/GOx, Ppy/GOx and PTh/GOx formation, respectively. It was determined that the highest polymerization rate of PANI/GOx, Ppy/GOx, and PTh/GOx composite nanoparticles was achieved in solution containing 0.75 mg mL⁻¹ of GOx and 0.05 mol L⁻¹ of glucose. The influence of the enzymatic polymerization duration on the formation of PANI/GOx and Ppy/GOx composite nanoparticles was spectrophotometrically investigated. The most optimal duration for the enzymatic synthesis of PANI/GOx and Ppy/GOx composite nanoparticles was in the range of 48–96 h. It was determined that the diameter of formed PANI/GOx and Ppy/GOx composite nanoparticles depends on the duration of polymerization using dynamic light scattering technique (DLS), and it was in the range of 41–167 nm and 65–122 nm, when polymerization lasted from 16 to 120 h. Full article

Conductive polymers have been widely investigated in various applications. Several conductive polymers, such as polyaniline (PANI), polypyrrole (PPy), poly(3,4-ethylenedioxythiophene) (PEDOT)), and polythiophene (PTh) have been loaded with various semiconductor nanomaterials to prepare the composite photocatalysts. However, a critical review of conductive polymer-based composite photocatalysts has not been available yet. Therefore, in this review, we summarized the applications of conductive polymers in the preparation of composite photocatalysts for photocatalytic degradation of hazardous chemicals, antibacterial, and photocatalytic hydrogen production. Various materials were systematically surveyed to illustrate their preparation methods, morphologies, and photocatalytic performances. The synergic effect between conductive polymers and semiconductor nanomaterials were observed for a lot of composite photocatalysts. The band structures of the composite photocatalysts can be analyzed to explain the mechanism of their enhanced photocatalytic activity. The incorporation of conductive polymers can result in significantly improved visible-light driven photocatalytic activity by enhancing the separation of photoexcited charge carriers, extending the light absorption range, increasing the adsorption of reactants, inhibiting photo-corrosion, and reducing the formation of large aggregates. This review provides a systematic concept about how conductive polymers can improve the performance of composite photocatalysts. Full article