Search Results (131)

The development of metallic coatings as Ni-Co alloys, with particular emphasis on their homogeneity, processability, and sustainability, is of the utmost significance. To address these challenges, the utilization of phenylsalicylimines (PSIs) as additives within deep eutectic solvents (DES) was investigated, assessing their influence on the electrodeposition process of these metals at an intermediate temperature of 60 °C, while circumventing aqueous reaction conditions. The findings demonstrated that the incorporation of PSIs markedly enhances coating uniformity, resulting in an optimal cobalt content of 37% and an average thickness of 24 µm. Electrochemical evaluations revealed improvements in charge and mass transfer, thereby optimizing process efficiency. Moreover, computational studies confirmed that PSIs form stable complexes with Co (II), modulating the electrochemical characteristics of the system through the introduction of the diethylamino electron-donating group, which significantly stabilizes the coordinated forms with both components of the DES. Additionally, the coatings displayed exceptional corrosion resistance, with a rate of 0.781 µm per year, and achieved an optimal hardness of 38 N HRC, conforming to ASTM B994 standards. This research contributes to the development of electroplating bath designs for metallic coating deposition and lays the groundwork for the advancement of sophisticated technologies in functional coatings that augment corrosion resistance and mechanical properties. Full article

Electro-oxidation of urea (UOR) in alkaline medium is one of the most effective alternative ways of producing green hydrogen, as the oxidation potential in UOR is less and thermodynamically more favorable than conventional water oxidation. The development of cost-effective materials in catalyzing UOR is recently seeking more attention in the research hotspot. Suitably modifying the Ni-based catalysts towards active site creation and preventing surface passivation is much important in this context, following which we reported the synthesis of Ni₃S₂ (NS) supported with CuCo (CC) bimetallic (NSCC). A simple hydrothermal route for NS synthesis and the electrodeposition method for CuCo (CC) deposition is adapted in a self-supported manner. The NS and CC catalysts exhibited sheet-like morphology, as confirmed by SEM and TEM analysis. The bimetallic CC deposition prevented the surface passivation of nickel sulfide (NS) over oxygen evolution reaction (OER) and improved the charge-transfer kinetics. The NSCC catalyst catalyzed UOR in an alkaline medium, which required a lower potential of 1.335 V vs. RHE to attain the current density of 10 mAcm⁻², with a lower Tafel slope value of 131 mVdec⁻¹. In addition, a two-electrode cell setup is constructed with an operating cell voltage of 1.512 V for delivering 10 mAcm⁻² current density. This study illustrates the new strategy of designing heterostructure catalysts for electrocatalytic UOR. Full article

This study focused on investigations of FeCo and FeNi nanowires prepared by template-assisted electrodeposition in polycarbonate membranes. Nanowires with a diameter of 100 nm and length of 6 µm were grown at different cathodic potentials and electrolyte compositions. Scanning electron microscopy images revealed densely packed arrays of continuous nanowires with smooth surfaces without visible porosity, regardless of the applied potential. Chemical analysis of nanowires pointed out weak sensitivity of chemical composition on the electrodeposition potential in the case of FeCo nanowires, in contrast to FeNi nanowires, where the increase of the cathodic potential resulted in higher Ni content. X-ray diffraction studies showed polycrystalline structure for all samples indicating B2 phase (Pm-3m) with isotropic growth of FeCo nanowires and FeNi₃ phase with a preferential growth along [111] direction in the case of FeNi nanowires. The peak broadening suggests a fine crystalline structure for both FeCo and FeNi materials with average crystallite sizes below 20 nm. Magnetic studies indicated an easy axis of magnetization parallel to the nanowire axis for all FeCo nanowires and potential-dependent anisotropy for FeNi nanowires. The present studies thus suggested the feasibility of producing segmented nanowires based on FeNi alloys, while poor chemical sensitivity to the applied potential was observed for the FeCo system. Full article

Medium-entropy alloys (MEAs) exhibit properties comparable or even superior to high-entropy alloys (HEAs). Due to their very good resistance in thermomechanical conditions and corrosive environments and unique electrical and magnetic properties, medium-entropy alloys are good candidates for coating applications. One of the most economically effective methods of producing metallic coatings is electrodeposition. In this work, the structure of an electrodeposited CoFeNi medium-entropy alloy coating on a copper substrate from a metal chlorides solution (FeCl₂ ∙ 4H₂O + CoCl₂ ∙ 6H₂O + NiCl₂ ∙ 6H₂O) with the addition of boric acid (H₃BO₃) was investigated. The coating was characterized by a nanocrystalline structure identified by transmission electron microscopy examination and X-ray diffraction methods. Based on XRD and TEM, the face-centered cubic (FCC) phase of the CoFeNi MEA coating was identified. The high corrosion resistance of the MEA coating in a 3.5% NaCl environment at 25 °C was confirmed by electrochemical tests. Full article

The galvanostatic electrodeposition of cobalt–nickel alloy coatings performed out on a 304 stainless steel substrate. The electrolyte baths contained metals salts, along with boric acid and sodium benzene sulfonate (SBS) as an organic additive in the deposition process. Structural and topographic analyses were performed using SEM-EDS and AFM techniques, respectively. The findings confirm the formation of nanostructured coatings. The images depicting various stages of coating formation indicated the inhibitory role of the organic additive. The presence of SBS enabled the formation of a coating composed of grains with diverse geometries and significantly reduced surface roughness. Hydrogen evolution was conducted in an alkaline environment (1 M NaOH). Overpotentials for the different structures were recorded at 10 mA/cm², yielding 196 mV and 225 mV for the coatings deposited with and without SBS, respectively. Additionally, experiments were performed in a laboratory-designed electrolyzer, which allowed for the measurement of gas volumes (H₂ and O₂) generated under constant voltage and current conditions. The results demonstrated that the obtained coatings perform more effectively as hydrogen evolution cathodes than currently used materials, particularly under higher current densities. Electrolysis was conducted for 8 h, revealing improved stability of the coating deposited in the presence of SBS. Full article

This paper presents a non-enzymatic sensor for glucose detection in an environment where glucose and insulin coexist. The sensor is based on a three-electrode chip fabricated by etching the copper foil of a printed circuit board. The working electrode is coated with a graphene oxide-polyvinyl alcohol composite film, followed by the electroplating of a nickel–cobalt layer and an additional surface treatment using O₂ plasma. The experimental results indicate that within a glucose concentration of 2 mM to 10 mM and an insulin concentration of 0.1 mM to 1 mM, the measured current exhibits a linear relationship with the concentration of glucose or insulin, regardless of whether cyclic voltammetry or linear sweep voltammetry is used. However, the detection limit for insulin is 0.01 mM, ensuring that glucose detection remains unaffected by insulin interference. In this sensor, nickel–cobalt serves as a catalyst for glucose and insulin detection, while the graphene oxide-polyvinyl alcohol composite enhances sensing performance. Full article

The development of advanced electrocatalysts plays a pivotal role in enhancing hydrogen production through water electrolysis. In this study, we employed a two-step electrodeposition method to fabricate a 3D porous Cu-Co-Ni alloy with superior catalytic properties and long-term stability for hydrogen evolution reaction (HER). The resulting trimetallic alloy, Cu@Cu-Ni-Co, demonstrated significant improvements in structural integrity and catalytic performance. A comparative analysis of electrocatalysts, including Cu, Cu@Ni-Co, and Cu@Cu-Ni-Co, revealed that Cu@Cu-Ni-Co achieved the best results in alkaline media. Electrochemical tests conducted in 1.0 M NaOH showed that Cu@Cu-Ni-Co reached a current density of 10 mA cm⁻² at a low overpotential of 125 mV, along with a low Tafel slope of 79.1 mV dec⁻¹. The catalyst showed exceptional durability, retaining ~95% of its initial current density after 120 h of continuous operation at high current densities. Structural analysis confirmed that the enhanced catalytic performance arises from the synergistic interaction between Cu, Ni, and Co within the well-integrated trimetallic framework. This integration results in a large electrochemical active surface area (ECSA) of 380 cm² and a low charge transfer resistance (15.76 Ω), facilitating efficient electron transfer and promoting superior HER activity. These findings position Cu@Cu-Ni-Co as a highly efficient and stable electrocatalyst for alkaline HER in alkaline conditions. Full article

In this study, a sulfur-doped cobalt–iron catalyst (CoFeS/NF) was synthesized on a nickel foam (NF) substrate via a facile one-step electrodeposition method, and its performance in urea electrolysis for hydrogen production was systematically investigated. Sulfur doping induced significant morphology optimization, forming a highly dispersed nanosheet structure, which enhanced the specific surface area increase by 1.9 times compared with the undoped sample, exposing abundant active sites. Meanwhile, the introduction of sulfur facilitated electron redistribution at the surface modulated the valence states of nickel and cobalt, promoted the formation of high-valence Ni³⁺/Co³⁺, optimized the adsorption energy of the reaction intermediates, and reduced the charge transfer resistance. Electrochemical evaluations revealed that CoFeS/NF achieves a current density of 10 mA cm⁻² at a remarkably low potential of 1.18 V for the urea oxidation reaction (UOR), outperforming both the undoped catalyst (1.24 V) and commercial RuO₂ (1.35 V). In addition, the catalyst also exhibited excellent catalytic activity and long-term stability in the total urea decomposition process, which was attributed to the amorphous structure and the synergistic enhancement of corrosion resistance by sulfur doping. This study provides a new idea for the application of sulfur doping strategy in the design of multifunctional electrocatalysts, which promotes the coupled development of urea wastewater treatment and efficient hydrogen production technology. Full article

Research into the introduction of alloying and reinforcing nanocomposites into nickel (Ni) coatings has been motivated by the need for tribologically superior coatings that will improve energy efficiency. Using pulse electrodeposition, this work investigates the effects of adding cobalt (Co) as the alloying nanoparticle and silicon carbide (SiC), zirconium oxide (ZrO₂), and aluminium oxide (Al₂O₃) as reinforcing nanocomposites to Ni coatings. The surface properties, mechanical strength, nanotribological behaviour, and wettability of these coatings were analysed. Surface characteristics were evaluated by the use of a Scanning Electron Microscope, revealing a grain dimension reduction of approximately ~7–43% compared to pristine Ni coatings. When alloying and reinforcing nanocomposites were added to Ni coatings, nanoindentation research showed that there was an increase in nanohardness of ~12% to ~69%. This resulted in an improvement in the tribological performance from approximately 2% to 65%.The hydrophilic nature of Ni coatings was observed with wettability analysis. This study demonstrates that nanocomposite reinforcement can be used to customise Ni coatings for applications that require exceptional tribological performance. The results point to the use of Ni-Co coatings for electronics and aerospace sectors, with more improvements possible with the addition of reinforcing nanoparticles. Full article

In this study, nickel–cobalt (Ni–Co) coatings were fabricated via electrodeposition using a 2² central composite factorial design with two central and two axial points, totaling ten experiments. The effects of pH and current density on the coatings’ chemical composition and properties were evaluated. Coatings were characterized by microstructure, morphology, magnetic properties, and corrosion resistance. The results showed that pH significantly influenced chemical composition, while current density had no notable effect. Acidic pH produced cobalt-rich coatings (43–81 at.%), with uniform morphology, higher saturation magnetization, and lower corrosion resistance. Maximum cobalt content (81 at.%) resulted in a mixed face-centered cubic (fcc) + hexagonal close-packed (hcp) phase. Alkaline pH yielded nickel-rich coatings (89–95 at.%), featuring nodular morphology, lower magnetization, higher corrosion resistance, and, exclusively, the fcc phase. The highest polarization resistance (66.1 kΩ) occurred at pH 8.83 and 60 mA/cm², while resistance decreased with increasing cobalt content. The pH effect on deposition was linked to the formation of citrate complexes: ammonia and citrate complexes promoted nickel deposition under alkaline conditions, while stable cobalt complexes dominated in an acidic pH. These findings highlight the potential to tailor Ni–Co coatings for applications such as corrosion-resistant coatings (nickel-rich) or magnetic devices (cobalt-rich). Full article

The NiCo₂O₄ Nanosheets@Carbon fibers composites have been successfully synthesized by a facile co-electrodeposition process. The mesoporous NiCo₂O₄ nanosheets aligned vertically on the surface of carbon fibers and crosslinked with each other, producing loosely porous nanostructures. These hybrid composite electrodes exhibit high specific capacitance in a three-electrode cell. The asymmetric supercapacitor (NiCo₂O₄ Nanosheets@Carbon fibers//Graphene oxide) displayed a high specific capacitance of 91 F g⁻¹ and excellent cycling stability with a capacitance retention of 94.5% at 5 A g⁻¹ after 10,000 cycles. The device also achieved a notable energy density of 52 Wh kg⁻¹ coupled with a power density of 3.5 kW kg⁻¹ and a high power density of 7.1 kW kg⁻¹ with an energy density of 21 Wh kg⁻¹. This study shed light on the great potential of this asymmetric device as future supercapacitor. Full article

In this study, we investigate the electrodeposition of various metals on silicon. Mn, Co, Ni, Ru, Pd, Rh, and Pt were identified as promising candidates for controlled electrodeposition onto silicon. Electrochemical evaluations employing cyclic voltammetry, Scanning Electron Microscopy (SEM) associated with energy-dispersive X-Ray Spectroscopy (SEM-EDS), and X-Ray Photoelectron Spectroscopy (XPS) techniques confirmed the deposition of Pd, Rh, and Pt as nanoparticles. Multi-cycle charge-controlled depositions were subsequently performed to evaluate the possibility of achieving tunable electrodeposition of nanostructured rhodium on n-doped silicon. The procedure increased surface coverage from 9% to 84%, with the average particle size diameter ranging from 57 nm to 168 nm, and with an equivalent thickness of the deposits up to 43.9 nm, varying the number of charge-controlled deposition cycles. The electrodeposition of rhodium on silicon presents numerous opportunities across various scientific and technological domains, driving innovation and enhancing the performance of devices and materials used in catalysis, electronics, solar cells, fuel cells, and sensing. Full article

In this study, a three-dimensional (3D) interconnected porous Ni/SiC skeleton (3D Ni/SiC) was synthesized by binder-free hydrogen bubble template-assisted electrodeposition in an electrolyte containing Ni²⁺ ions and SiC nanopowders. This 3D Ni/SiC skeleton served as a substrate for directly synthesizing nickel–cobalt layered double hydroxide (LDH) nanosheets via electrodeposition, allowing the formation of a nickel–cobalt LDH nanosheet-decorated 3D Ni/SiC skeleton (NiCo@3D Ni/SiC). The multiscale hierarchical structure of NiCo@3D Ni/SiC was attributed to the synergistic interaction between the pseudocapacitor (3D Ni skeleton and Ni–Co LDH) and electrochemical double-layer capacitor (SiC nanopowders). It provided a large specific surface area to expose numerous active Ni and Co sites for Faradaic redox reactions, resulting in an enhanced pseudocapacitance. The as-fabricated NiCo@3D Ni/SiC structure demonstrated excellent rate capability with a high areal capacitance of 1565 mF cm⁻² at a current density of 1 mA cm⁻². Additionally, symmetrical supercapacitor devices based on this structure successfully powered commercial light-emitting diodes, indicating the potential of as-fabricated NiCo@3D Ni/SiC in practical energy storage applications. Full article

In this study, we have prepared Ni-W/Cr₃C₂ composite electrodeposits through the diffuse reinforcement mechanism of chromium carbide nanoparticles. These electrodeposits exhibit excellent corrosion resistance and are designed to effectively protect the structural materials of pipe columns under the harsh CO₂ corrosion environments faced by carbon sequestration and utilization technologies. A systematic investigation was conducted into the micro-morphology, profile undulation, phase composition, and surface chemical state of the electrodeposits. Furthermore, the corrosion-resistant behavior of Ni-W/Cr₃C₂ composite electrodeposits was investigated in simulated corrosive environments (i.e., brine solution containing 3.5 wt% NaCl and CO₂-saturated brine). We then evaluated their corrosion response under the aforementioned conditions using electrochemical methods. In addition, the EIS of electrodeposited coatings revealed that the dense oxide film layer formed on the surface of the deposits, which acted as a primary barrier against corrosion, playing a pivotal role in maintaining the overall corrosion resistance of the material. Full article

The Ni-GQDs composite plating was created using direct current (DC), single-pulse, and double-pulse power supplies, with GQDs serving as additives under supercritical CO₂ conditions. A comparative analysis was conducted to evaluate the effects of different electrodeposition power sources on the microstructure and properties of the Ni-GQDs composite plating. High-Resolution Transmission Electron Microscopy (HRTEM) was employed to investigate the distribution of GQDs within the composite plating as well as to analyze d-spacing and diffraction patterns. Scanning Electron Microscopy (SEM) was utilized to illustrate the surface morphology of the plating and assess its surface quality. The grain size and preferred orientation of the plated layer were examined using X-ray Diffraction (XRD), while Atomic Force Microscopy (AFM) was used to evaluate the roughness of the surface. To compare the abrasion resistance of the various plating types, wear amounts and friction coefficients were measured through friction and wear tests. Additionally, corrosion resistance tests were performed to assess the corrosion resistance of each plating variant. The results indicate that the Ni-GQDs-III composite layers produced via double-pulse electrodeposition exhibit superior surface quality, characterized by smaller grain sizes, enhanced surface flatness, reduced surface roughness, and improved resistance to wear and corrosion. Full article