Search Results (120)

Measuring pH is a critical parameter in environmental monitoring, biomedical diagnostics, food safety, and industrial processes. Optical fiber sensors have proven highly effective for pH detection due to their exceptional sensitivity, rapid response, and resistance to electromagnetic interference, making them well suited for real-time monitoring. This review offers a comprehensive analysis of recent advances in optical fiber-based pH sensors, covering key techniques such as fluorescence-based, absorbance-based, evanescent wave, and interferometric methods. Innovations in Fiber Bragg Grating and Surface Plasmon Resonance technologies are also examined. The discussion extends to the impact of pH-sensitive coatings—ranging from nanomaterials and polymeric films to graphene-based compounds—on enhancing sensor performance. Recent advancements have also enabled automation in data analysis and improvements in remote sensing capabilities. The review further compares the economic viability of optical fiber sensors with traditional electrochemical methods, while acknowledging persistent issues such as temperature cross-sensitivity, long-term stability, and fabrication costs. Overall, recent developments have broadened the functionality and application scope of these sensors by improving efficiency, accuracy, and scalability. Future research directions are outlined, including advanced optical interrogation techniques, such as Addressed Fiber Bragg Structures (AFBSs), microwave photonic integration, and optimized material selection. These approaches aim to enhance performance, reduce costs, and enable the broader adoption of optical fiber pH sensors. Full article

This article presents the findings of an experimental study conducted on a vertical axis wind turbine (VAWT) tower instrumented with cascaded fiber Bragg grating (FBG) sensors to detect bending deformations. Structural health monitoring (SHM) is an essential need in the industry to reduce costs and maintenance time, and to prevent machine failures. First, FBG strain sensors were glued vertically along the tower to investigate the sensors behavior as a function of their height. The maximum signal-to-noise ratio is obtained when FBGs are placed at the tower base. Then, four packages were installed inside the tower, at the base, according to four cardinal directions. Each package contains an FBG strain sensor, and an extra temperature FBG for discrimination. The use of easy-to-deploy packages is a must for industrial installations. Afterwards, by using power spectral density (PSD) on the strain signals, three sources of tower oscillations are discovered: wind force, structure unbalance, and 1st tower mode resonance, each with its intrinsic frequency. Wind force and structure unbalance cause mechanical stresses at a frequency proportional to the wind turbine rotational speed, while the 1st tower mode frequency depends only on the machine geometry, regardless of the rotational speed. This study also analyzes the deformation amplitude for different rotational rates within the VAWT operational range (10–35 rpm). The resonance amplitude depends on the proximity of the rotational rate to the resonant frequency (22 rpm) and the duration at that rate. For structure unbalance, the oscillation amplitude increases with the rotational rate, due to the centrifugal effect. It is supposed that wind force deformation amplitude naturally depends on wind speed, which is unpredictable at a given precise time. The results of our experimental observations are very valuable for both the wind turbine manufacturer and owner. Full article

This work presents a novel $C{O}_2$ gas sensor based on a slotted polymer-phaseshift Bragg grating (SP-PSBG) waveguide filled with polyhexamethylene biguanide (PHMB) as the sensing medium. The transmission resonance, characterized by a narrow peak with a full width at half maximum (FWHM) of 1.6 nm within the Bragg grating bandgap, is highly responsive to refractive index changes in PHMB caused by variations in $C{O}_2$ concentration. Numerical simulations demonstrate a sensitivity of 14.4 pm/ppm, outperforming conventional gas sensors based on functional material coatings. This enhanced performance comes from the direct interaction between the PHMB-filled resonant structure and the cladding that contains $C{O}_2$ molecules, eliminating the need for polymer-coated cladding layers. The optimization approach employed in this design focuses on maximizing the optical confinement factor within the PHMB-filled slot, leading to an effective overlap between the guided optical mode and the sensing material. Full article

This paper presents the development and validation of a high-resolution photonic and wireless monitoring system for knee-referenced gait cycle analysis. The proposed system integrates a single optical Fiber Bragg Grating (FBG) sensor with a resonance wavelength of 1547.76 nm and electronic modules with inertial and magnetic sensors, achieving a 10 p.m. wavelength resolution and 1° angular accuracy. The innovative combination of these components enables a direct correlation between wavelength variations and angular measurements without requiring goniometers or motion capture systems. The system’s practicality and versatility were demonstrated through tests with seven healthy individuals of varying physical attributes, showcasing consistent performance across different scenarios. The FBG sensor, embedded in a polymeric foil and attached to an elastic knee band, maintained full sensing capabilities while allowing easy placement on the knee. The wireless modules, positioned above and below the knee, accurately measured the angle formed by the femur and tibia during the gait cycle. The experimental prototype validated the system’s effectiveness in providing precise and reliable knee kinematics data for clinical and sports-related applications. Full article

Currently, optical fibers play a leading role in telecommunications, serve as special transmission components for industrial applications, and form the basis of highly sensitive sensor elements. One of the most commonly used modifications is the reduction in the initial dimensions of the cladding and core to a few or several micrometers, allowing the evanescent wave emerging from the tapered region to interact with the surrounding environment. As a result, the microfiber formed in this way is highly sensitive to any changes in its surroundings, making it an ideal sensing element. This article primarily focuses on reviewing the latest trends in science involving various types of optical microfibers, including tapers, rings, loops, coils, and tapered fiber Bragg gratings. Additionally, it discusses the most commonly used materials for coating fiber optic elements—such as metals, oxides, polymers, organic materials, and graphene—which enhance sensitivity to specific physical factors and enable selectivity in the developed sensors. Full article

We present and demonstrate a highly birefringent fiber Bragg grating (Hi-Bi FBG) that was fabricated using a femtosecond laser to induce a sawtooth stress region near the FBG. The FBG is fabricated with a femtosecond laser point-by-point method, while the sawtooth stress region is generated in fiber cladding using the femtosecond laser along a sawtooth path. This sawtooth stressor can introduce an anisotropic and asymmetric refractive index profile in the cross-section of the fiber, resulting in additional birefringence up to 2.97 × 10⁻⁴ along the axial direction of the FBG. The central wavelengths of the Hi-Bi FBG at the fast and slow axes exhibit different sensitivities to temperature and strain, allowing simultaneous measurement of the strain and temperature by tracking the resonant wavelength shifts in the two axes. The experimental results show that the temperature sensitivities of the fast and slow axes are 10.32 pm/°C and 10.42 pm/°C, while the strain sensitivities are 0.91 pm/µε and 0.99 pm/µε. The accuracy of this proposed sensor in measuring strain and temperature is estimated to be 2.2 µε and 0.2 °C. This approach addresses the issue of cross-sensitivity between temperature and strain and offers some advantages of low cost, compact size, and significant potential for advancements in practical multi-parameter sensing applications. Full article

The increasing demand for high-precision, real-time sensing in various fields has spurred the development of optical fiber grating sensors (OFGSs). This study reviews the research field of OFGSs, exploring their historical development, current trends, and future opportunities through scientometric analysis utilizing CiteSpace. The research landscape has grown exponentially since the early studies on fiber Bragg gratings and long-period fiber gratings in the 1990s. Bibliometric data reveal that engineering, optics, and instrumentation dominate OFGS research, with emerging interdisciplinary applications in environmental, biological, and medical sensing. Key contributors have advanced OFGSs through femtosecond laser inscription, novel materials, and intelligent system integration, as reflected in co-citation and keywords analyses. Trends such as AI-driven optimization, surface plasmon resonance, and 3D printing signal shift toward adaptive, multifunctional sensing systems capable of addressing diverse challenges. This review also maps the evolution of OFGS research, transitioning from foundational strain and temperature sensing to sophisticated systems for structural health monitoring, biomedical diagnostics, and robotics. Despite global disruptions, the field’s recovery highlights its critical role in advancing sensing technologies. By combining thematic insights from co-citation and keyword analyses, this study identifies both established directions and transformative opportunities, providing a holistic understanding of OFGS research and its trajectory. Full article

Accurate real-time temperature measurement under extreme thermal-pressure conditions remains challenging in aerospace. Sapphire fiber Bragg gratings (FBGs), exhibiting temperature measurement capabilities up to 1900 °C, demonstrate suitability for such extreme environments. However, the development of a high-performance demodulation system capable of processing sapphire FBG signals over wide spectral ranges at elevated speeds remains a technical challenge. This study presents a real-time FBG signal demodulation system that incorporates an all-dielectric subwavelength grating edge filter. The designed grating, comprising a TiO₂/Si₃N₄ subwavelength unit array, modulates Mie-type electric and magnetic multipole resonances to achieve precisely tailored transmission and reflection spectra. Simulation results indicate that the grating exhibits low ohmic loss, excellent linearity, complementary transmission/reflection characteristics, a wide linear range, and angular-dependent tunability. The designed edge-filter-based demodulation system incorporates dual single-point detectors to simultaneously monitor the transmitted and reflected signals. Leveraging the functional relationship between the center wavelength of the FBG and the detected signals, this system enables high-speed, wide-range interrogation of the center wavelength, thus facilitating real-time demodulation for wide-range temperature sensing. The proposed method and system are validated through theoretical modeling, offering an innovative approach for sapphire FBG signal demodulation under extreme thermal-pressure conditions. Full article

Fiber Bragg gratings (FBGs) are useful components in fiber optic sensing systems, which can be highly multiplexed and distributed. In recent years, fabrication using ultrafast lasers has made these devices much more versatile and robust, but questions concerning their high-temperature performance remain. The wavelength resonance of an FBG is naturally sensitive to various parameters of its environment; in particular, changes in the temperature or strain of a fiber tend to induce observable shifts in the Bragg wavelength. Thus, FBGs can offer reliable sensing solutions, provided they are isolated from other influences and their wavelength responses remain well characterized. Nonetheless, it is important to be aware that the isothermal wavelength drift of unstrained FBGs has been previously observed. When this occurs, it can lead to measurement errors and a requirement for sensor recalibration. This study presents a comparison of long-term isothermal wavelength drifts observed at 600 °C, 800 °C, 900 °C and 1000 °C for large numbers of Type II FBGs in different kinds of single-mode fibers. The results provide guidance for the design of high-temperature sensing systems, both in terms of fiber selection and for estimating the maximum time before recalibration becomes necessary to maintain a specified accuracy. Full article

The wavelength shift in TFBG cladding resonance is a practical parameter due to its independence from power fluctuations coming from the light source or fiber bends. It is possible to select the cladding modes that are characterized by the center wavelength shifts while changing the refractive index of the surrounding medium. In the case of a single TFBG, this parameter is strongly dependent on the input light polarization angle. In this paper, we present the possibility of reducing interference of polarization changes to measure the refractive index by using the wavelength shift in Bragg grating cladding modes with the cascade structure called the perpendicular TFBG (P-TFBG). The wavelength shift in the selected cladding mode was analyzed and compared in the case of a single grating and proposed cascade. In the case of P-TFBG, the dependence on the corresponding cladding mode of a single TFBG with the same inscription parameters is reduced to 16.15%. The analysis of mode wavelength instead of the previously reported amplitude provides a wider measurement range of possible SRI and protects the results from power fluctuations. Full article

Ultrafast fiber lasers have shown exceptional performance across various domains, including material processing, medical applications, and optoelectronic communication. The semiconductor saturable absorber mirror (SESAM) is a key enabler of ultrafast laser operation. However, the narrow wavelength range and limited modulation depth of conventional SESAMs pose challenges to further advancing ultrafast fiber laser technology. To address these limitations, we explored the integration of guided mode resonance (GMR) effects to enhance light–matter interaction within the absorption layer. By incorporating subwavelength dielectric film gratings onto the cap layer of SESAMs, we excited GMR and formed a microcavity structure in conjunction with the distributed Bragg mirror (DBR). This design significantly improved the absorption efficiency of InAs quantum dots. The experimental results demonstrate that the modulation depth of the SESAM increased from 6.7% to 17.3%, while the pulse width was reduced by 2.41 times. These improvements facilitated the realization of a high-quality, stable ultrafast fiber laser. This study not only broadens the application potential of ultrafast lasers in diverse fields but also offers a practical pathway for advancing SESAM technology toward industrial-scale deployment. Full article

The effects of mechanical vibrations on control system stability could be significant in control systems designed on the assumption of rigid-body dynamics, such as launch vehicles. Vibrational loads can also cause damage to launch vehicles due to fatigue or excitation of structural resonances. This paper investigates a method to control structural vibrations in real time using a finite number of strain measurements from a fiber Bragg grating (FBG) sensor array. A scaled test article representative of the structural dynamics associated with an actual launch vehicle was designed and built. The main modal frequencies of the test specimen are extracted from finite element analysis. A model of the test article is developed, including frequency response, thruster dynamics, and sensor conversion matrices. A model-based robust controller is presented to minimize vibrations in the test article by using FBG measurements to calculate the required thrust in two cold gas actuators. Controller performance is validated both in simulation and on experiments with the proposed test article. The proposed controller achieves a 94% reduction in peak–peak vibration in the first mode, and 80% reduction in peak–peak vibration in the second mode, compared to the open loop response under continuously excited base motion. Full article

The paper presents the results of developing Er-doped optical fibers for creating random single-frequency lasers in the wavelength range of 1570–1610 nm. The possibility of broadening the luminescence band of Er³⁺ ions in silicate glasses in the long-wavelength region of the spectrum by introducing a high concentration of P₂O₅, as well as by additional doping with Sb₂O₃, is investigated. It is found that both approaches do not improve the dynamics of luminescence decay in the L-band. In addition, Er₂O₃-GeO₂-Al₂O₃-SiO₂ and Er₂O₃-GeO₂-Al₂O₃-P₂O₅-SiO₂ glasses were studied as the core material for L-band optical fibers. The developed fibers exhibited high photosensitivity and a high gain of 5 and 7.2 dB/m, respectively. In these fibers, homogeneous arrays of extended weakly reflecting Bragg gratings were recorded directly during the fiber drawing process. Samples of arrays 5 m long and with a narrow reflection maximum at ~1590 nm were used as the base for laser resonators. Narrow-band random laser generation in the wavelength region of 1590 nm was recorded for the first time. At a temperature of 295 K, the laser mode was strictly continuous wave and stable in terms of output power. The maximal power exceeded 16 mW with an efficiency of 16%. Full article

This study explores the achievement of a tunable true time-delay (TTD) system for a microwave phased-array antenna (MPAA) by incorporating the reversible phase-transition property of phase-change material (PCM) with Bragg gratings (BGs) and a cascade of three phase-shifted Bragg grating resonators (CPSBGRs). The goal was to design a low-power-consuming, non-volatile highly tunable compact TTD system for beam steering. A programmable on/off reflector was designed by changing a PCM-incorporated BG/CPSBGR from one phase to another. By arranging several programmable on/off reflectors in a row, a delay line was realized, and by incorporating several delay lines, the TTD system was achieved. Numerical simulations and parametric analyses were conducted for the evaluation of the TTD system’s performance at an operating wavelength of 1550 nm and 1550.6 nm for programmable on/off reflectors with BGs and CPSBGRs. The findings point out the effectiveness of incorporating PCMs with BGs/CPSBGRs, thereby maintaining a high performance with less complexity. Full article

The hybrid heterostructures formed between two-dimensional (2D) materials and organic molecules have gained great interest for their potential applications in advanced photonic and optoelectronic devices, such as solar cells and biosensors. Characterizing the interfacial structure and dynamic properties at the molecular level is essential for realizing such applications. Here, we report a time-resolved sum-frequency generation (TR-SFG) approach to investigate the hybrid structure of polymethyl methacrylate (PMMA) molecules and 2D transition metal dichalcogenides (TMDCs). By utilizing both infrared and visible light, TR-SFG can provide surface-specific information about both molecular vibrations and electronic transitions simultaneously. Our setup employed a Bragg grating for generating both a narrowband probe and an ultrafast pump pulse, along with a synchronized beam chopper and Galvo mirror combination for real-time spectral normalization, which can be readily incorporated into standard SFG setups. Applying this technique to the TMDC/PMMA interfaces yielded structural information regarding PMMA side chains and dynamic responses of both PMMA vibrational modes and TMDC excitonic transitions. We further observed a prominent enhancement effect of the PMMA vibrational SF amplitude for about 10 times upon the resonance with TMDC excitonic transition. These findings lay a foundation for further investigation into interactions at the 2D material/organic molecule interfaces. Full article