Search Results (11)

This article presents a stochastic model for the effect of interference caused by a sudden increase in the number of users that access a 4 QAM digital communication system. As demonstrated, the rapid increase in the number of users that access the system causes a non-stationary traffic in the network. A stochastic differential approach is used to model the epidemic interference effect. Full article

Modulation format identification (MFI) is one of the most critical functions embedded in digital coherent receivers in elastic optical networks (EONs). In view of inherent amplitude and phase characteristics of received signals, different modulation formats exhibit a set of notable features in the polar coordinate system, based on which an MFI scheme incorporating the Gaussian weighted k-nearest neighbors (KNN) algorithm was proposed to identify polarization division multiplexed (PDM)-QPSK/-16QAM/-32QAM/-64QAM/-128QAM signals. The performance of the proposed scheme was numerically verified in 28GBaud coherent optical communication systems. The numerical simulation results show that, to achieve 100% correct identification rates for all of the five modulation formats, the required minimum optical signal-to-noise ratios (OSNRs) were less than their relevant thresholds corresponding to the 20% forward error correction (FEC). The tolerable ranges of the residual chromatic dispersion (CD) for QPSK, 16QAM, 32QAM, 64QAM, and 128QAM were −1920 ps/nm~1920 ps/nm, −720 ps/nm~360 ps/nm, −1200 ps/nm~1680 ps/nm, −600 ps/nm~360 ps/nm, and −600 ps/nm~480 ps/nm, respectively. Meanwhile, the results demonstrate the maximum tolerable differential-group delay (DGD) for the QPSK, 16QAM, 32QAM, 64QAM, and 128QAM signals were 34 ps, 16 ps, 20 ps, 6 ps, and 1.2 ps, respectively. In addition, the simulated results also show that the proposed MFI scheme is robust against the fiber nonlinearities, even if the launch power is increased to 4 dBm. Full article

Digital terrestrial television is now implemented in many countries worldwide and is now mature. Digital Video Broadcasting-Terrestrial, second generation (DVB-T2) is the European standard adopted or deployed by European and African countries which uses Orthogonal Frequency-Division Multiplexing (OFDM) modulation to achieve good throughput performance. However, its main particularity is the number of subcarriers operated for OFDM modulation which varies from 1024 to 32,768 subcarriers. Also, mobile reception is planned in DVB-T2 in addition to rooftop antenna and portable receptions planned in DVB-T. However, the main challenge of DVB-T2 for mobile reception is the presence of a carrier frequency offset (CFO) which degrades the system performance by inducing an Intercarrier Interference (ICI) on the DVB-T2 signal. This paper evaluates the system performance in the presence of the CFO when Gaussian noise and a TU6 channel are applied. Universal Filtered Multicarrier (UFMC) and non-uniform constellations (NUCs) have previously demonstrated good performance in comparison with OFDM and Quadrature Amplitude Modulation (QAM) in DVB-T2. The impact of CFO on the UFMC- and NUC-based DVB-T2 system is additionally investigated in this work. The results demonstrate that the penalties induced by CFO insertion in UFMC- and NUC-based DVB-T2 are highly reduced in comparison to those for the native DVB-T2. At a bit error rate (BER) of ${10}^{-3}$, the CFO penalties induced by the native DVB-T2 are $0.96$$\mathrm{d}$$\mathrm{B}$ and 4 $\mathrm{d}$$\mathrm{B}$, respectively, when only Additive White Gaussian Noise (AWGN) is used and when TU6 is additionally considered. The penalties are equal to $0.84$$\mathrm{d}$$\mathrm{B}$ and $0.2$$\mathrm{d}$$\mathrm{B}$ for UFMC/NUC-based DVB-T2. Full article

To achieve higher visible light communication (VLC) traffic capacity, using the wide bandwidth light-emitting diode (LED) and spectral efficiency modulation signal, is currently the most commonly used method. In this demonstration, we apply the orthogonal frequency division multiplexing quadrature amplitude modulation (OFDM-QAM) with bit- and power-loading algorithm on single blue LED to achieve >1 Gbit/s VLC capacity, when a 400 MHz bandwidth avalanche photodiode (APD)-based receiver (Rx) is exploited for decoding. Here, the higher sensitivity APD can be applied to compensate for the wireless VLC link length in the proposed LED VLC system, and due to the lower LED illumination (255 to 40 lux), is used for the indoor access network after passing the wireless link length of 1 to 4 m. As a result, using single blue LED can achieve 0.962 to 1.057 Gbit/s OFDM rate with available 400 MHz bandwidth APD in poorly illuminated condition indoors without applying analogy equalization. Full article

We propose a novel reception scheme for twin single-sideband (twin-SSB) signals using just a single photodetector (PD), significantly reducing the system complexity and cost. To detect a twin-SSB with power-unbalanced quadrature-phase shift keying (QPSK) sidebands upon detection via a single PD at the receiver side, two QPSKs carried in two sidebands are coherently superposed and detected in a 16-ary quadrature amplitude modulation (16-QAM) format. This technique notably diminishes the linearity and effective number of bits required for the transmitter components in high-speed optical transmission systems. Moreover, a hierarchical blind-phase search (HBPS) algorithm is proposed to compensate for the imperfect phase rotation of QPSK signals during transmission. To demonstrate the effectiveness of our proposed method, we successfully conducted simulations of 112 Gb/s 16-QAM signal transmission over a 10 km standard single-mode fiber (SSMF), achieving bit error ratios (BERs) of $7.84\times {10}^{-4}$, well below the 7% hard-decision forward error correction (HD-FEC) threshold of $3.8\times {10}^{-3}$. In addition, the synthetic transmission scheme proposed in this paper is compared with the traditional 16-QAM signal transmission scheme, and the results show that the proposed scheme does not introduce a performance cost with the same received optical power (ROP) and transmission distance. Full article

In this paper, a 4 amplitude shift keying (4-ASK) fast orthogonal frequency division multiplexing (FOFDM) scheme was experimentally investigated over a turbulent air–water channel for optical wireless communications. The experiment results showed that the 4-ASK-FOFDM modulated signals were not sensitive to weak atmospheric turbulence, and the bit-error rate (BER) was lower than the 7% forward error correction (FEC) limit of 3.8 × 10⁻³. Under the condition of the same spectra efficiency, the 4-ASK-FOFDM scheme just had a tiny performance penalty compared to the 16-QAM-OFDM scheme. Consequently, the 4-ASK-FOFDM scheme is a promising alternative to the conventional 16-QAM-OFDM scheme in optical wireless communications. Full article

We experimentally incubate a ground-breaking design, for the first time, of concurrent electro-optical semiconductor optical amplifier Mach–Zehnder interferometer mixing (SOA-MZI) based on a differential transformation methodology. Projecting the simultaneous electro-optical mixing system and improving its efficiency and quality achievement in optical and electrical features is a crucial task due to the characteristics of an optical pulse source (OPS) operating with a repetition rate of $f=$ 58.5 GHz and a pulse width duration of 1 picosecond (ps). The resultant of the contemporaneous electro-optical mixing exhibits exceptional passive power stability, reaching 0.8% RMS over a two-hour period. Furthermore, when the optical bandpass filter is controlled at the data wavelength of 1540 nm, we achieve up to 30 dBm of the overall mean output power with an optical conversion gain of 46 dB and an exceptionally high optical signal-to-noise ratio reaching 80 dB. Using orthogonal frequency division multiplexing (OFDM) signals, each data subcarrier is modulated using 128 quadratic amplitude modulation (128-QAM) at carrier frequencies $f_k$ and simultaneously up-mixed to high aim frequencies $nf\pm f_k$ at the SOA-MZI output. Additionally, the resulting OFDM_128-QAM up-mixed signal is examined using the specifications for the error vector magnitudes (EVMs) and the electrical conversion gains (ECGs). The SOA-MZI mixing experiment can handle high frequencies up to 120 GHz. Positive ECGs are followed by a sharp reduction over the entire band of the aim frequencies. The highest frequency range achieved during the realistic investigation is shown at $2f+f_4=$ 120 GHz, where the EVM reaches 8% with a symbol rate of 15 GSymb/s. Furthermore, the concurrent OFDM_128-QAM up-mixed signal achieves an absolute maximum bit rate of 80.4 Gbit/s. The investigation into the simultaneous electro-optical mixing regime is finally supported by unmatched characterization improvements. Full article

Quadrature amplitude modulation (QAM) constellation and Golay complementary sequences (GCSs) are usually applied in orthogonal frequency division multiplexing (OFDM) systems to obtain a higher data rate and a lower peak-to-mean envelope power ratio (PMEPR). In this paper, after a sufficient search of the literature, it was found that increasing the family size is an effective way to improve the data rate, and the family size is mainly determined by the number of offsets in the general structure of QAM GCSs. Under the guidance of this idea, we propose a new construction for $4^q$-QAM GCSs through generalized Boolean functions (GBFs) based on a new description of a $4^q$-QAM constellation, which aims to enlarge the family size of GCSs and obtain a low PMEPR. Furthermore, a previous construction of $4^q$-QAM GCSs presented by Li has been proved to be a special case of the new one, and the family size of new sequences is much larger than those previously mentioned, which means that there was a great improvement in the data rate. On the other hand, a previous construction of 16-QAM GCSs presented by Zeng is also a special case of the new one in this paper, when $q=2$. In the meantime, the proposed sequences have the same PMEPR upper bound as the previously mentioned sequences presented by Li when applied in OFDM systems, which increase the data rate without degrading the PMEPR performance. The theoretical analysis and simulation results show that the proposed new sequences can achieve a higher data rate and a low PMEPR. Full article

In this paper, the uplink in a two-hop 5G new radio co-operative system using Relay Nodes (RNs) in millimeter bands has been simulated and studied. We focus on an uplink Amplify-and-Forward Relay Node (A&F RN) and Decode-and-Forward Relay Node (D&F RN) with an mmWave-band transceiver chain (Tx/Rx). We study two uplink mmWave MIMO D&F relaying protocols assuming, firstly, the complete knowledge of the uplink channel and, secondly, the uplink channel estimation through a Least Square (LS) algorithm. To verify the benefits of the proposed uplink mmWave MIMO co-operative network, a link-level co-operative simulator has been developed using Matlab${}^{\mathrm{TM}}$ and Simulink${}^{\mathrm{TM}}$ software, where an indoor-to-outdoor scenario and mmWave transceiver with off-the shelf components are considered. The main novelty of this link-level co-operative simulator and the implemented relay nodes is the usage of signals with 5G NR features, such as UL-SCH transport channel coding and PUSCH generation, which are the other main contributions of this article. Based on the numerical results in terms of the achievable Bit Error Rate (BER) and throughput, we show that the two-hop uplink co-operative network substantially improves the performance in the communications between the NR-User Equipment (NR-UE) and the logical 5G Radio Node (gNodeB). For example, the results from using uplink mmWave NR-D&F protocols far exceed those achieved with the uplink mmWave NR-A&F algorithm; in the case of the 64-QAM modulation scheme for the SISO technique, an improvement of 6.5 Mbps was achieved using the D&F PCE protocol, taking into account that the 256-QAM constellation is higher by 4.05 Mbps. On the other hand, an average throughput enhancement of 28.77 Mbps was achieved when an uplink mmWave (2 × 4 × 4) D&F PCE strategy was used versus an uplink mmWave SISO D&F LS protocol for a Signal-to-Noise Ratio (SNR) = 20 dB and 64-QAM signal. However, an improvement of 56.42 Mbps was reached when a 256-QAM modulation scheme was employed. Furthermore, this paper introduces the first study to develop an uplink mmWave MIMO 5G co-operative network platform through a Software Defined Radio (SDR) from a practical implementation point of view. Full article

An underwater universal filtered multicarrier (UFMC)-based voice transmission scheme is proposed using a 512-point inverse discrete Fourier transform, utilizing 10 sub-bands, and that each had 20 subcarriers. In this proposed UFMC method, the adaptive modulation technologies with 4 quadrature amplitude modulation (QAM), 16-QAM, and low-density parity-check (LDPC) channel coding were integrated. Additionally, the bit error rate (BER), transmission power weighting, the ratios of power-saving, and underwater voice transmission performance with perfect channel estimation (PCE), and 5% and 10% channel estimation errors (CEEs) were investigated. The underwater voice transmission had a BER quality of service ${10}^{-3}$. Simulation results showed that the PCE outperformed 5% and 10% CEEs, under 4-QAM, with gains of 0.5 and 0.9 dB, respectively, and a BER of $4\times {10}^{-4}$. The PCE outperformed 5% and 10% CEEs, under 16-QAM, with gains of 0.5 and 2.4 dB, respectively, and a BER of $8.5\times {10}^{-4}$. The proposed UFMC scheme can be applied to underwater voice transmission with a BER below ${10}^{-3}$ The proposed system showed a superior capability to contend with additive white Gaussian noise, underwater multipath channel fading, and CEEs. Full article

Analog fronthauling is currently promoted as a bandwidth and energy-efficient solution that can meet the requirements of the Fifth Generation (5G) vision for low latency, high data rates and energy efficiency. In this paper, we propose an analog optical fronthaul 5G architecture, fully aligned with the emerging Centralized-Radio Access Network (C-RAN) concept. The proposed architecture exploits the wavelength division multiplexing (WDM) technique and multicarrier intermediate-frequency-over-fiber (IFoF) signal generation per wavelength in order to satisfy the demanding needs of hotspot areas. Particularly, the fronthaul link employs photonic integrated circuit (PIC)-based WDM optical transmitters (Txs) at the baseband unit (BBU), while novel reconfigurable optical add-drop multiplexers (ROADMs) cascaded in an optical bus are used at the remote radio head (RRH) site, to facilitate reconfigurable wavelength switching functionalities up to 4 wavelengths. An aggregate capacity of 96 Gb/s has been reported by exploiting two WDM links carrying multi-IF band orthogonal frequency division multiplexing (OFDM) signals at a baud rate of 0.5 Gbd with sub-carrier (SC) modulation of 64-QAM. All signals exhibited error vector magnitude (EVM) values within the acceptable 3rd Generation Partnership Project (3GPP) limits of 8%. The longest reach to place the BBU away from the hotspot was also investigated, revealing acceptable EVM performance for fiber lengths up to 4.8 km. Full article