Search Results (11)

When cultivating on wheat bran or deactivated fungal mycelium as a model of “natural growth”, the ability of Trichoderma to synthesize extracellular L-lysine-α-oxidase (LysO) simultaneously with cell-wall-degrading enzymes (proteases, xylanase, glucanases, chitinases, etc.), responsible for mycoparasitism, was shown. LysO, in turn, causes the formation of H₂O₂ and pipecolic acid. These compounds are known to be signaling molecules and play an important role in the induction and development of systemic acquired resistance in plants. Antagonistic effects of LysO have been demonstrated against phytopathogenic fungi and Gram-positive or Gram-negative bacteria with dose-dependent cell death. The antimicrobial effect of LysO decreased in the presence of catalase. The generating intracellular ROS in the presence of LysO was also shown in both bacteria and fungi, which led to a decrease in viable cells. These results suggest that the antimicrobial activity of LysO is due to two factors: the formation of exogenous hydrogen peroxide as a product of the enzymatic oxidative deamination of L-lysine and the direct interaction of LysO with the cell wall of the micro-organisms. Thus, LysO on its own enhances the potential of the producer in the environment; namely, the enzyme complements the strategy of the fungus in biocontrol and indirectly participates in inducing SAR and regulating the relationship between pathogens and plants. Full article

The structural and electro-thermophysical characteristics of organosilicon elastomers modified with multilayer carbon nanotubes (MWCNTs) synthesized on Co-Mo/Al₂O₃-MgO and metallic (Cu or Ni) microparticles have been studied. The structures were analyzed with scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, and energy-dispersive X-ray spectroscopy (EDX). The main focus of this study was the influence of metallic dispersed fillers on the resistance of a modified elastomer with Cu and Ni to the degradation of electrophysical parameters under the action of applied electrical voltage. The distribution of the temperature field on the surface of a modified polymer composite with metallic micro-dimensional structures has been recorded. The collected data demonstrate the possibility of controlling the degradation caused by electrical voltage. It has been found that repeated on/off turns of the elastomer with an MWCNTs on 50 and 100 cycles leads to a deterioration in the properties of the conductive elastomer from the available power of 1.1 kW/m² (−40 °C) and, as a consequence, a decrease in the power to 0.3 kW/m² (−40 °C) after 100 on/off cycles. At the same time, the Ni additive allows increasing the power by 1.4 kW/m² (−40 °C) and reducing the intensity of the degradation of the conductive structures (after 100 on/off cycles up to 1.2 kW/m² (−40 °C). When Ni is replaced by Cu, the power of the modified composite in the heating mode increases to 1.6 kW/m² (−40 °C) and, at the same time, the degradation of the conductive structures in the composite decreases in the mode of cyclic offensives (50 and 100 cycles) (1.5 kW/m² (−40 °C)). It was found that the best result in terms of heat removal is typical for an elastomer sample with an MWCNTs and Cu (temperature reaches 93.9 °C), which indicates an intensification of the heat removal from the most overheated places of the composite structure. At the same time, the maximum temperature for the Ni additives reaches 86.7 °C. A sample without the addition of a micro-sized metal is characterized by the local unevenness of the temperature field distribution, which causes undesirable internal overheating and destruction of the current-conducting structures based on the MWCNTs. The maximum temperature at the same time reaches a value of 49.8 °C. The conducted studies of the distribution of the micro-sizes of Ni and Cu show that Cu, due to its larger particles, improves internal heat exchange and intensifies heat release to the surface of the heater sample, which improves the temperature regime of the MWCNTs and, accordingly, increases resistance to electrophysical degradation. Full article

Assaying changes in the amount of DNA in single cells is a well-established method for studying the effects of various perturbations on the cell cycle. A drawback of this method is the need for a fixation procedure that does not allow for in vivo study nor simultaneous monitoring of additional parameters such as fluorescence of tagged proteins or genetically encoded indicators. In this work, we report on a method of Histone Abundance Quantification (HAQ) of live yeast harboring a GFP-tagged histone, Htb2. We show that it provides data highly congruent with DNA levels, both in Saccharomyces cerevisiae and Ogataea polymorpha yeasts. The protocol for the DNA content assay was also optimized to be suitable for both Ogataea and Saccharomyces yeasts. Using the HAQ approach, we demonstrate the expected effects on the cell cycle progression for several compounds and conditions and show usability in conjunction with additional fluorophores. Thus, our data provide a simple approach that can be utilized in a wide range of studies where the effects of various stimuli on the cell cycle need to be monitored directly in living cells. Full article

Metal-organic frameworks (MOFs) are a very promising platform for applications in various industries. In recent years, a variety of methods have been developed for the preparation and modification of MOFs, providing a wide range of materials for different applications in life science. Despite the wide range of different MOFs in terms of properties/sizes/chemical nature, they have not found wide application in biomedical practices at present. In this review, we look at the main methods for the preparation of MOFs that can ensure biomedical applications. In addition, we also review the available options for tuning the key parameters, such as size, morphology, and porosity, which are crucial for the use of MOFs in biomedical systems. This review also analyses possible applications for MOFs of different natures. Their high porosity allows the use of MOFs as universal carriers for different therapeutic molecules in the human body. The wide range of chemical species involved in the synthesis of MOFs makes it possible to enhance targeting and prolongation, as well as to create delivery systems that are sensitive to various factors. In addition, we also highlight how injectable, oral, and even ocular delivery systems based on MOFs can be used. The possibility of using MOFs as therapeutic agents and sensitizers in photodynamic, photothermal, and sonodynamic therapy was also reviewed. MOFs have demonstrated high selectivity in various diagnostic systems, making them promising for future applications. The present review aims to systematize the main ways of modifying MOFs, as well as the biomedical applications of various systems based on MOFs. Full article

The development of reliable and effective functional materials that can be used in various technological fields and environmental conditions is one of the goals of modern nanotechnology. Heating elements’ manufacturing requires understanding the laws of heat transfer under conditions of different supply voltages, as this expands the possibilities of such materials’ application. Elastomers based on silicon-organic compounds and polyurethane modified with multi-walled carbon nanotubes (MWCNTs) were studied at various concentrations of Ni/MgO or Co-Mo/MgO and voltages (220, 250, and 300 V). It was found that an increase in voltage from 220 to 300 V leads to an initial increase in specific power on one-third followed by a subsequent decrease in a specific power when switched on again to 220 V (for −40 °C) of up to ~44%. In turn, for a polyurethane matrix, an increase in voltage to 300 V leads to an initial peak power value of ~15% and a decrease in power when switched on again by 220 V (for −40 °C) to ~36% (Ni/MgO -MWCNT). The conducted studies have shown that the use of a polyurethane matrix reduces power degradation (associated with voltage surges above 220 V) by 2.59% for Ni/MgO–based MWCNT and by 10.42% for Co-Mo/MgO. This is due to the better heat resistance of polyurethane and the structural features of the polymer and the MWCNT. The current studies allow us to take the next step in the development of functional materials for electric heating and demonstrate the safety of using heaters at a higher voltage of up to 300 V, which does not lead to their ignition, but only causes changes in electrophysical parameters. Full article

The turn to hydrogen as an energy source is a fundamentally important task facing the global energetics, aviation and automotive industries. This step would reduce the negative man-made impact on the environment on the one hand, and provide previously inaccessible power modes and increased resources for technical systems, predetermining the development of an absolutely new life cycle for important areas of technology, on the other. The most important aspect in this case is the development of next-generation technologies for hydrogen industry waste management that will definitely reduce the negative impact of technology on the environment. We consider the approaches and methods related to new technologies in the area of hydrogen storage (HS), which requires the use of specialized equipment equipped with efficient and controlled temperature control systems, as well as the involvement of innovative materials that allow HS in solid form. Technologies for controlling hydrogen production and storage systems are of great importance, and can be implemented using neural networks, making it possible to significantly improve all technological stages according to the criteria of energy efficiency reliability, safety, and eco-friendliness. The recent advantages in these directions are also reviewed. Full article

Of great importance in materials science is the design of effective functional materials that can be used in various technological fields. Nanomodified materials, which have fundamentally new properties and provide previously unrealized properties, have acquired particular importance. When creating heating elements and materials for deformation measurement, it is necessary to understand the patterns of heat release under conditions of mechanical deformation of the material, as this expands the potential applications of such materials. A study of elastomers modified with multi-walled carbon nanotubes (MWCNTs) has been carried at the MWCNTs concentration of 1–8 wt.%. The modes of heat release of nanomodified elastomers at a voltage of 50 V at different levels of tension are reported. The increment of the MWCNTs concentration to 7 wt.% leads to an increment in the power of heat emissions. It is worth noting the possibility of using the obtained elastomer samples with MNT as sensitive elements of strain sensors, which will allow obtaining information about physical and chemical parameters following the principles of measuring the change in electrical resistance that occurs during stretching and torsion. The changes in conductivity and heat emission under different conditions have been studied in parallel with Raman mapping and infrared thermography. The reported studies allow to make the next step to develop flexible functional materials for the field of electric heating and deformation measurement based on elastic matrices and nanoscale conductive fillers. Full article

Nanotechnology plays an important role in biological research, especially in the development of delivery systems with lower toxicity and greater efficiency. These include not only metallic nanoparticles, but also biopolymeric nanoparticles. Biopolymeric nanoparticles (BPNs) are mainly developed for their provision of several advantages, such as biocompatibility, biodegradability, and minimal toxicity, in addition to the general advantages of nanoparticles. Therefore, given that biopolymers are biodegradable, natural, and environmentally friendly, they have attracted great attention due to their multiple applications in biomedicine, such as drug delivery, antibacterial activity, etc. This review on biopolymeric nanoparticles highlights their various synthesis methods, such as the ionic gelation method, nanoprecipitation method, and microemulsion method. In addition, the review also covers the applications of biodegradable polymeric nanoparticles in different areas—especially in the pharmaceutical, biomedical, and agricultural domains. In conclusion, the present review highlights recent advances in the synthesis and applications of biopolymeric nanoparticles and presents both fundamental and applied aspects that can be used for further development in the field of biopolymeric nanoparticles. Full article

Effective and durable treatment of glioblastoma is an urgent unmet medical need. In this article, we summarize a novel approach of a physical method that enhances the effectiveness of radiotherapy. High atomic number nanoparticles that target brain tumors are intravenously administered. Upon irradiation, the nanoparticles absorb X-rays creating free radicals, increasing the tumor dose several fold. Radiotherapy of mice with orthotopic human gliomas and human triple negative breast cancers growing in the brain showed significant life extensions when the nanoparticles were included. An extensive study of the properties of the iodine-containing nanoparticle (Niodx) by the Nanotechnology Characterization Laboratory, including sterility, physicochemical characterization, in vitro cytotoxicity, in vivo immunological characterization, and in vivo toxicology, is presented. In summary, the iodine nanoparticle Niodx appears safe and effective for translational studies toward human use. Full article

Cobalt nanoparticles (CoNPs) are promising nanomaterials with exceptional catalytic magnetic, electronic, and chemical properties. The nano size and developed surface open a wide range of applications of cobalt nanoparticles in biomedicine along with those properties. The present review assessed the current environmentally friendly synthesis methods used to synthesize CoNPs with various properties, such as size, zeta potential, surface area, and magnetic properties. We systematized several methods and provided some examples to illustrate the synthetic process of CoNPs, along with the properties, the chemical formula of obtained CoNPs, and their method of analysis. In addition, we also looked at the potential application of CoNPs from water purification cytostatic agents against cancer to theranostic and diagnostic agents. Moreover, CoNPs also can be used as contrast agents in magnetic resonance imaging and photoacoustic methods. This review features a comprehensive understanding of the synthesis methods and applications of CoNPs, which will help guide future studies on CoNPs. Full article

Several metal nanoparticles have been developed for medical application. While all have their benefits, gold nanoparticles (AuNPs) are ideal in cancer therapy and diagnosis as they are chemically inert and minimally toxic. Several studies have shown the potential of AuNPs in the therapeutic field, as photosensitizing agents in sonochemical and photothermal therapy and as drug delivery, as well as in diagnostics and theranostics. Although there is a significant number of reviews on the application of AuNPs in cancer medicine, there is no comprehensive review on their application both in therapy and diagnostics. Therefore, considering the high number of studies on AuNPs’ applications, this review summarizes data on the application of AuNPs in cancer therapy and diagnostics. In addition, we looked at the influence of AuNPs’ shape and size on their biological properties. We also present the potential use of hybrid materials based on AuNPs in sonochemical and photothermal therapy and the possibility of their use in diagnostics. Despite their potential, the use of AuNPs and derivatives in cancer medicine still has some limitations. In this review, we provide an overview of the biological, physicochemical, and legal constraints on using AuNPs in cancer medicine. Full article