Next Article in Journal
Study of Deactivation in Suzuki Reaction of Polymer-Stabilized Pd Nanocatalysts
Next Article in Special Issue
Analysis and Optimization of Two Film-Coated Tablet Production Processes by Computer Simulation: A Case Study
Previous Article in Journal
Current State of Porous Carbon for Wastewater Treatment
Previous Article in Special Issue
Integration and Evaluation of Intra-Logistics Processes in Flexible Production Systems Based on OEE Metrics, with the Use of Computer Modelling and Simulation of AGVs
 
 
Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
Journals
Processes
Volume 8
Issue 12
10.3390/pr8121652
processes-logo
Submit to this Journal Review for this Journal Propose a Special Issue
► Article Menu

Article Menu

share Share announcement Help format_quote Cite question_answer Discuss in SciProfiles
first_page
settings
Order Article Reprints
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Abrasive Water Jet Cutting of Hardox Steels—Quality Investigation

by
Tibor Krenicky
1,*,
Milos Servatka
2,
Stefan Gaspar
1 and
Jozef Mascenik
1
1
Faculty of Manufacturing Technologies with a Seat in Presov, Technical University of Kosice, Sturova 31, 08001 Presov, Slovakia
2
IMSLOV, P. Horova 19, 08001 Presov, Slovakia
*
Author to whom correspondence should be addressed.
Processes 2020, 8(12), 1652; https://doi.org/10.3390/pr8121652
Submission received: 9 November 2020 / Revised: 9 December 2020 / Accepted: 12 December 2020 / Published: 14 December 2020
(This article belongs to the Special Issue Expanding the Horizons of Manufacturing: Towards Wide Integration, Smart Systems and Tools)
Browse Figures
Review Reports Versions Notes

Abstract

The paper aims to study the surface quality dependency on selected parameters of cuts made in Hardox™ by abrasive water jet (AWJ). The regression process was applied on measured data and the equations were prepared for both the Ra and Rz roughness parameters. One set of regression equations was prepared for the relationship of Ra and Rz on cutting parameters—pumping pressure, traverse speed, and abrasive mass flow rate. The second set of regression equations describes relationships between the declination angle in kerf as the independent variable and either the Ra or the Rz parameters as dependent variables. The models can be used to predict cutting variables to predict the surface quality parameters.
Keywords: abrasive water jet; cutting; surface quality; quality prediction abrasive water jet; cutting; surface quality; quality prediction

Share and Cite

MDPI and ACS Style

Krenicky, T.; Servatka, M.; Gaspar, S.; Mascenik, J. Abrasive Water Jet Cutting of Hardox Steels—Quality Investigation. Processes 2020, 8, 1652. https://doi.org/10.3390/pr8121652

AMA Style

Krenicky T, Servatka M, Gaspar S, Mascenik J. Abrasive Water Jet Cutting of Hardox Steels—Quality Investigation. Processes. 2020; 8(12):1652. https://doi.org/10.3390/pr8121652

Chicago/Turabian Style

Krenicky, Tibor, Milos Servatka, Stefan Gaspar, and Jozef Mascenik. 2020. "Abrasive Water Jet Cutting of Hardox Steels—Quality Investigation" Processes 8, no. 12: 1652. https://doi.org/10.3390/pr8121652

APA Style

Krenicky, T., Servatka, M., Gaspar, S., & Mascenik, J. (2020). Abrasive Water Jet Cutting of Hardox Steels—Quality Investigation. Processes, 8(12), 1652. https://doi.org/10.3390/pr8121652

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop