Vehicle emissions are among the main sources of pollutants impairing air quality in urban areas. The level of pollution produced by traffic emissions is mainly influenced by the type of vehicles on the road, the volume of traffic and the distance from the street. However, weather conditions unfavorable to atmospheric dispersion can cause high level of vehicular traffic pollutants even at a great distance from busy roads. Indeed, high concentration peaks of the main combustion tracers, such as NOx, are measured by the local Environmental Agencies at both urban traffic and urban background sites.
The urban traffic stations, placed in close proximity to the busiest urban streets, are directly influenced by local traffic, while at background monitoring stations the pollution level should be influenced by the integrated contribution from all sources upwind of the station (Directive 2008/50/CE, received in Italy by the D.Lgs. 155—13 August 2010). However, vehicular emissions can strongly affect the urban air quality so much that during rush hours, traffic peaks are large even at urban background stations.
At urban traffic sites, vehicle emissions on the nearby roads sum with the urban background levels [1
], and higher NOx
concentration values are observed than at urban background stations. Moreover, the rural background concentrations can be attributed to natural sources and long range transport at local and global scale, with negligible influence of nearby sources. Therefore, according to the previous rationale [1
], to identify the contribution of local and distant emission sources to atmospheric pollution in urban areas, air quality observations at rural, urban background and urban traffic sites must be compared. A recent study [2
] demonstrated that the “Lenschow approach” [1
] is a valuable method to estimate the impact of cities on their air pollution only when two assumptions are concurrently fulfilled. The first is verified when the pollution concentrations experienced at rural background sites are not influenced by the emissions occurred within the city of interest, whereas the second requires that rural background concentrations are identical between rural and city locations when city emissions are set to zero.
With the aim of investigating the contribution of different emission sources to urban air pollution, several methods have been tested in recent years, such as interpolation methods or land use regression models [3
]. However, atmospheric dispersion models were proven to be among the most successful approach in reproducing pollutant concentrations, especially when applied for environmental impact assessments [7
]. The skill of dispersion models to account also for obstacle-resolving domains at very high resolution (at micro scale) [10
] makes them an effective tool to describe the fate of intra-urban atmospheric emissions and to support urban air pollution control strategies.
Nitrogen oxides (NOx
) in vehicle exhausts consist of NO and NO2
. The NO2
mass fraction of total NOx
) is of particular importance for several reasons: Its higher toxicity, causing irritation of airways in the human respiratory system and aggravation of respiratory diseases [11
], its higher atmospheric lifetime compared to NO and because regulatory limits are established for hourly maximum NO2
(Directive 2008/50/CE, received in Italy by the D.Lgs. 155—13 August 2010). NO is rapidly transformed to NO2
by photochemical atmospheric reactions, hence primary NO2
from vehicle exhaust emissions should be present mostly at urban traffic sites, i.e., in the immediate vicinity of the sources. Conversely, secondary NO2
should be prevailing at urban background sites, where air quality is affected by the combination of urban and regional pollutant contribution without the direct effect of nearby sources. Nevertheless, meteorological conditions favorable to air masses stagnation may produce similar concentration values at both urban traffic and background sites, consequently affecting also the atmospheric NO2
ratio. The estimation of NO2
concentration values by the means of dispersion models can therefore be very complex.
Several methods have been recently applied to discern local traffic impact from the background. Among the others, it is worth mentioning the interpolation of rolling minima and the differences in downwind and upwind pollutant averages, both tested by Hilker, N. et al. [13
] to distinguish between background and near-road pollution concentrations. Other statistical methods, based for example on hierarchical clustering or probabilistic approach such as the finite mixture models, have been implemented to estimate urban background concentrations using traffic and background measurements [14
]. An alternative to statistical methods, as introduced before, is represented by air quality dispersion models, which at the cost of high computing resources combined with the need of qualified users can be exploited to elaborate specific emission scenarios. More in detail, by applying the so called Brute-force method [15
] it is possible to isolate the effect of specific emission sources by performing and subtracting simulations with and without the source of interest.
On the other hand, when dispersion models are not designed to account for chemical reactions, different screening approaches have been defined by the EPA (Environmental Protection Agency) to calculate NO2
concentrations starting from NOx
emissions. The latter, usually called Ambient Ratio Method [17
], allow estimating the NO2
ratio produced by specific emission sources, useful for comparison with the measured NO2
ratio at the air quality station of interest.
In a recent study [18
], the single micro scale lagrangian particle model (LPM) Micro SWIFT SPRAY (MSS) [19
] was used to simulate the atmospheric dispersion of primary NOx
vehicular emissions in urban areas with intense traffic, in Modena and Reggio Emilia (Northern Italy), i.e., the dispersion of NO and primary NO2
, because LPMs are not able to simulate atmospheric chemistry processes. These two cities are located within the Po Valley, a European hotspot for NOx
, whose weather is characterised by calm winds [9
] and high pressure events producing long lasting high concentrations even in remote rural sites [20
dispersion produced by urban traffic flows was also simulated for the city of Modena [23
] adopting a multi-level modelling approach involving two different tools, the Parallel Micro SWIFT SPRAY (PMSS) [24
] modelling system able to estimate the primary contribution of urban sources taking into account the effect of street canyon in urban complex environment and the WRF-Chem model [26
]. This latter was applied to compute urban NOx
background concentrations produced by the sources located outside the urban area of Modena or by emission sectors different from traffic both in and out of the urban area. Among the main advantages expressed by WRF-Chem it is worth remembering the ability to simulate the chemical transformation of trace gases and aerosols that occur in the atmosphere [27
]. Therefore, it is possible to estimate the formation of secondary compounds starting from precursors, such as NO2
, by using specific computational schemes.
Within this paper the difference in NO2 and NOx between the regulatory air quality data collected at urban traffic and urban background stations, in Modena and Reggio Emilia, are investigated. Moreover, with the aim of estimating primary and secondary NO2 level at the urban background sites, observed concentrations at air quality stations are compared with NO2 and NOx concentrations simulated with the WRF-Chem model for the city of Modena. In addition, estimate of primary traffic emissions focusing on the same area, taken from the literature, was used for further discussion and comparison.
2. Materials and Methods
Direct surveys of traffic flow by Doppler radar traffic counters for periods of about two weeks were carried out in two medium-sized cities (just under 200 thousand inhabitants) of the Po valley, Modena and Reggio Emilia, located about 40 km and 60 km West of Bologna respectively. In both cities high-traffic urban roads near busy intersections were monitored by the traffic counters.
The survey took place from 28 October to 8 November 2016 in Modena and from 13 to 24 January 2014 in Reggio Emilia [18
]. During both measurement campaigns, either in Modena and in Reggio Emilia, hourly concentration of atmospheric NO and NOx
were provided by the local urban traffic station placed in close proximity to the high-traffic urban road monitored by traffic counters, and by the urban background station; all these stations belong to the regional air quality monitoring network of the regional environmental agency (Arpae) (Figure 1
). An estimation of the NO2
atmospheric concentration was given by considering the primary emissions (NO and NOx
) produced by the traffic recorded in the measurement campaigns.
The survey in Modena was carried out under typical autumn weather conditions in the Po Valley: Generally low rainfall, average wind speed <2 m s−1, 20% calm events (i.e., wind speed <1 m s−1), mixing height generally <300 m and average daily air temperature in the range 7.4 to 13.6 °C. From 29 October to 1 November 2016 the traffic was less intense than usual for a national holiday.
In Reggio Emilia the measurement campaign was carried out during unusual weather conditions for winter in the Central Po Valley: The survey period was characterized by strong atmospheric instability, exceptional rainfall, average wind speed <1 m s−1 and average daily air temperature in the range 3 to 10 °C, with a greater daytime excursion. During the whole January 2014 there were heavy rainfalls and uncommonly high temperatures, the largest for January over the period 2010–2017. These conditions were favorable to the atmospheric dispersion of pollutants.
In both case studies [18
] the NOx
emission factors (i.e., primary NO and NO2
) were evaluated according to the European EMEP/SEE guidelines [29
], using the data (time, length and speed of passing vehicles) recorded by the radars and the vehicle fleet composition data for the year 2015 in Modena [30
] and for the year 2013 in Reggio Emilia [31
]. Given the radar’s inability to count stationary vehicles, only warm emissions (engine at normal operating temperature) were considered. The hourly mass flows of NOx
emitted were estimated by coupling the hourly radar records with the EF value for each counted vehicle: the traffic emissions modulated according to the hourly variation of the traffic flows were thus obtained for each day of the two surveys.
The atmospheric dispersion of NOx emissions was simulated using the Micro SWIFT SPRAY (MSS) model over 500 m × 500 m domains with grid step of 2 m (square cells). The simulation was run at hourly time step, consistently with the meteorological data provided by CALMET (for Reggio) and COSMO (for Modena) mesoscale model simulations performed by Arpae.
In order to analyze the contribution of all the emissions sectors except vehicular traffic, a chemical transport simulation was performed at very high resolution (1 km) only for the Modena case study. The WRF-Chem model [26
], which represents the state of the art system for numerical weather prediction coupled with aerosol and chemical modules to estimate air pollution concentrations, was applied over three nested domains (Figure 2
). The outer domain, with a resolution of 15 km covers most of the central Europe, while the central and the innermost domains focus respectively on the Northern part of Italy (at 3 km resolution) and on the Emilia-Romagna region (Northern Italy) with a resolution of 1 km. The vertical structure of the model includes 35 levels, with 12 of them in the lowest 3 km and the center of the first one approximately located at 35 m above the terrain. The maximum model altitude is fixed at 50 hPa.
The WRF-Chem set-up further encompasses the MOSAIC aerosol scheme and the MOZART gas-phase chemical mechanism. ECMWF ERA5 reanalysis data were used to drive meteorological simulation as boundary and initial condition, while the Corine Land Cover data were substituted to the original USGS dataset traditionally provided with the WRF-Chem code.
The emission data used in this case study are from the TNO-MACC III inventory. Two simulations were produced: One including emissions by all SNAP sectors of the inventory (hereafter full WRF-Chem background), and one without the traffic emissions for the urban area of Modena (hereafter WRF-Chem background). For this latter simulation the TNO-MACC emissions were post-processed with the aim of excluding traffic contribution to city pollution level. The original inventory was downscaled to 1 km within the innermost WRF-Chem domain for the 71–75 SNAP sectors using traffic modelled data as a proxy variable. The latter were estimated by the Municipality of Modena with the PTV VISUM model for a typical morning rush of a working day. Once created the downscaled grid dataset, the TNO-MACC III traffic emissions within the urban area of Modena were set to zero. Finally, NO2 and NOx background concentrations were modelled with WRF-Chem in the urban area of Modena considering the modified version of the TNO-MACC III inventory. It follows that secondary NO2 background concentrations are due to precursors in TNO-MACC III anthropogenic emissions. In order to estimate the WRF-Chem background bias in reproducing urban concentration levels, the additional full WRF-Chem background simulation was also performed.
4. Results and Discussion
With the aim of assessing the effect of the emissions in urban areas at traffic and background sites, measured concentrations of NOx and NO2
/NOx ratio were compared and investigated along with the simulation results. The modelling activity consists in the hourly NOx
concentrations reproduced at traffic sites with MSS at micro-scale resolution, for the duration of both the measurement campaigns, in Modena and Reggio Emilia [18
]. Moreover, the NO2
background concentrations were also estimated with the WRF-Chem model for the period between 28 October and 8 November 2016, only for the city of Modena [23
The micro-scale simulated concentrations were compared with NOx
observations at the urban traffic and urban background stations for both Modena and Reggio Emilia [18
], showing generally underestimation by the models.
A previous study [18
] suggests that, at urban traffic sites, inaccuracy or omissions in the estimate of primary traffic emissions might have contributed to cause this underestimation by the models. A further, relevant, possible cause of underestimation of simulated concentrations was indicated in the large contribution of secondary NO2
at urban traffic sites, a contribution that was not simulated by the micro-scale model. Indeed MSS, based on its characteristics, is not able to account for chemical reactions but can consider only the dispersion of primary NO and NO2
], assuming them as inert.
4.1. Air Quality Observations and Traffic Emission Inventory
For the two cases studied, a very similar trend of NOx
concentrations observed in urban traffic and in urban background sites during the survey was clearly shown (Pearson coefficient r = 0.80 for Reggio Emilia and r = 0.84 for the Modena case) [18
]. This is mainly due to the prevailing local meteorology, affected by the morphological conformation of the Po Valley and by the low intensity wind regime, with recurrent calm episodes that favor air masses homogenization. It’s worth noting that during the measurement campaign in Modena, persistent atmospheric stability conditions occurred, occasionally causing higher NOx
levels at the urban background than in the urban traffic site.
differences between measurements at the traffic and background stations respectively (hereafter ΔNOx
) can be explained by the local traffic emissions, whose contribution to air quality was modelled (and underestimated) by MSS. This underestimation, in the present work, was initially ascribed only to an underestimation of primary NOx
by the dispersion models. To verify this assumption, the ΔNO2
ratio (where ΔNO2
is the difference between the NO2
observations at urban traffic and at urban background sites), was compared with the primary NO2
ratio in total vehicular emissions derived from literature [33
] for the local vehicle fleet [30
]. The NO2
/NOx ratio in urban background observations is also considered in the comparison.
The test was performed using for each city the regulatory air quality observations from urban traffic and urban background sites collected during both the measurement campaigns, which were featured by very different weather conditions (Table 1
The ratio in primary NO2/NOx by vehicular emissions had a very similar result for Modena and Reggio Emilia, due to the similarity between their fleet composition; nonetheless the ΔNO2/ΔNOx and the NO2/NOx ratios at urban background are quite different.
The 2014 campaign showed in Reggio Emilia similar figures for primary NO2/NOx emissions and ΔNO2/ΔNOx ratios, and both are in the order of one third of NO2/NOx urban background ratio. This may indicate that the extra secondary NO2 at the urban traffic site is negligible when compared to the urban background one, and also that the direct impact of vehicular emissions at the urban background site is little. Conversely over the same period of the campaign in Reggio Emilia, the ΔNO2/ΔNOx ratio in Modena was much larger (about 73% more) than the ratio in the emissions of primary NO2/NOx and is in the order of two thirds of the NO2/NOx at the urban background site.
The uncommon weather conditions, favorable to pollutant dispersion, occurred during the campaign of January 2014 and emphasized the differences between traffic and background sites as it is clearly shown mostly from Reggio Emilia case study.
During the 2016 campaign the ΔNO2/ΔNOx ratio in Modena was much larger than the ratio in primary emissions of NO2/NOx, while the NO2/NOx ratio at the urban background is the same of the ΔNO2/ΔNOx. This suggests similar pollution sources between the urban traffic and urban background site of Modena, although with different intensities, i.e., the larger concentration observed at the urban traffic site originates from a similar source mix of the concentration observed at the urban background site. This occurrence is amplified by the concurrent weather conditions, which favor air masses stagnation and homogenization of aged emissions, determining similar pollution facies across the whole urban area.
However, these same weather conditions had a different effect in Reggio Emilia, where the ΔNO2/ΔNOx ratio at the urban traffic site is larger (ca. 71% more) than primary NO2/NOx ratio in emissions, but it is much lower (just over half) than the NO2/NOx ratio at the urban background site.
This is also confirmed by the comparison among the ratio between urban and rural background NO2
concentrations for the 2016 campaign period in Modena and Reggio Emilia, with the yearly average values provided by the local environmental agency [35
] for western-central Po valley. Over the full 2016 the ratio between the NO2
yearly average at the urban background and rural background sites in western-central Po valley was ca. 1.7 (170%), while the same ratio during the 2016 campaign period in Modena was 2.17 (217%) and in Reggio Emilia was about 1.37 (137%). NO2
levels observed at urban background in Modena during the 2016 campaign is comparable to the annual maximum among the average levels at all the urban background stations of the region: concurrent meteorological events particularly adverse for air quality in the whole region amplified the typical effects of autumn, occasionally leading to higher concentrations observed at the urban background than at the urban traffic site, as mentioned above.
The location of the monitoring sites of Reggio Emilia is probably better representative than for Modena of the different atmospheric pollution levels for the city, also in case of weather conditions unfavorable to pollutant dispersion in atmosphere. A large contribution of secondary NO2 at traffic site, as occurs mainly in Modena, may cause a considerable underestimation of MMS simulated concentrations.
4.2. Atmopsheric Modelling and Observations
Only for the 2016 campaign in Modena, the NO2 and NOx background concentrations were also estimated by the WRF-Chem model at 1 km resolution for the urban area of Modena. Two different simulations were performed in order to assess the contribution of different emission sources to the urban pollution level: Full WRF-Chem background and WRF-Chem background. For both these simulations, unlike for MSS, primary and secondary NO2 are included in NO2 evaluation by WRF-Chem.
Results from the modelling activity are presented in this section as follow. Firstly, the general WRF-Chem error in reproducing observations at urban background in Modena and at rural background sites is assessed. Secondly, simulated concentrations from the WRF-Chem background run are compared with observations and then with the full WRF-Chem background results (model-to-model inter-comparison). Finally, model results and observations are combined to deduce some additional considerations.
In Figure 3
the observed NOx
concentrations at urban background site in Modena are depicted along with modelled NOx
concentrations from the full WRF-Chem background and from the WRF-Chem background runs. In order to perform further comparisons and to support supplementary discussions, the observed rural background concentrations are also shown in the same figure.
The performances of the full WRF-Chem NOx
background simulation show that despite a general underestimation (MB equal to −17 µg m−3
, corresponding to −23% of NMB), modelled concentrations have a pattern similar to NOx
observations. In addition, further statistical analysis was conducted following the metrics suggested by Hanna, S. and Chang, J. [36
] for atmospheric dispersion. Table 2
summarizes the performance of the model in terms of FB, NMSE, FAC2 and NAD, along with respective benchmark values. Statistical scores show that WRF-Chem fulfills the acceptance criteria for almost all the metrics, also NAD (equal to 0.32) can be considered in line with the values suggested by Hanna, S. and Chang, J. [36
] since the proposed reference benchmarks are not to be considered rigid thresholds, but rather a general indication derived from many evaluation exercises involving many models and many types of observations.
As far NO2
is concerned (not shown), full WRF-Chem background presents a fraction of predicted concentrations within a factor of two of observations (FAC2) equal to 60%, greater than the reference criteria (50%). Moreover, regarding NMSE the model expresses its best performance with score equal to 0.70, largely lower than the acceptance benchmark (6). Also NAD, which score is 0.31 is very close to the acceptance value (0.30) and thus, as for NOx
, can be considered in line with the respective target. Notwithstanding the model seems to express good performances for the metrics defined by Hanna, S. and Chang, J. [36
], it is worth noting that modelled NO2
concentrations are characterized by a pronounced positive bias equal to +15 µg m−3
, corresponding to +50% of NMB; confirmed also by the FB with value equal to −0.40. This latter outcome may suggest that despite the overall sum of nitrogen oxides is simulated quite well, for this application the model tends to overestimate the amount of NO converted in NO2
, causing an overestimation of NO2
and therefore also a strong underestimation in simulated NO.
Since the goal of the WRF-Chem simulation was to estimate the pollution level in background areas, being this the most suitable application for this tool [27
], modelled NO2
concentrations from the full emissions run were also compared against observations at 10 rural background stations located within the innermost WRF-Chem domain. Modelled NOx
concentrations are negatively biased for all of the 10 stations, with a minimum MB equal to −10 µg m−3
(corresponding to −56% of NMB), nevertheless modelled NOx
concentrations for two stations were biased for about 1 µg m−3
(respectively −3% and −5% of NMB). In addition, simulated NOx
concentrations at 9 of the 10 stations present FAC2 equal or greater than 50% (Figure 4
), which is the reference value suggested by Hanna, S. and Chang, J. [36
] for “good” model performance. Average FAC2 over all the stations is 61%.
As for NOx
, modelled NO2
concentrations at rural background sites tend to be negatively biased, with 7 of the 10 stations characterized by negative bias. The minimum MB between modelled and observed NO2
is equal to −11 µg m−3
(−47% of NMB) and maximum MB is +4 µg m−3
(+23% of NMB). It is also worth mentioning that for 4 measurement sites modelled concentrations present an absolute bias less than 2 µg m−3
(corresponding to +3%, +9%, −4% and −7% of NMB) (Figure 4
). Average FAC2 over all the stations is 75%, with 9 of the 10 stations above 50% as suggested by Hanna, S. and Chang, J. [36
In the comparison with 2016 campaign observations in Modena (Figure 3
), the hourly NOx
concentrations simulated in full WRF-Chem background were quite correlated with hourly NOx
measured at Modena urban background site (Pearson correlation coefficient r
= 0.34), on the other hand WRF-Chem background hourly NOx
concentrations, obtained without accounting for traffic emissions in the urban area of Modena (Figure 3
), showed a lower correlation with hourly NOx
measured at Modena urban background site (Pearson correlation coefficient r
= 0.23). Moreover, the cumulative sum of NOx
simulated by full WRF-Chem background results in 76.8% of the observed values, conversely for WRF-Chem background this sum accounts for a small fraction (28.6%) of the observed urban background, and this is consistent with the exclusion of traffic emissions within the urban area (56% of the total NOx
emissions in the province of Modena [37
]) in this WRF-Chem simulation. This differences between full WRF-Chem background and WRF-Chem background confirms the outcome of the observation analysis (Table 1
), i.e., that the NOx
concentrations at urban background site in Modena are significantly impacted by traffic emissions.
WRF-Chem background was compared also with NOx
rural background observations for the same 2016 campaign period (Figure 3
): the NOx
rural background observations represent about 81% of WRF-Chem background, i.e., NOx
WRF-Chem background results closer to the order of rural rather than urban background intensity.
The ratio between NO2
concentrations simulated in the full WRF-Chem background and in the WRF-Chem background for the Modena urban area were compared with observed concentration ratio at urban background site for the 2016 campaign period. NO2
in full WRF-Chem background is equal to 82.2% and in WRF-Chem background is equal to 91.5%, values that are twice or more than twice with respect to the observed NO2
ratio at the urban background site (41.8%, Table 1
) and are also higher than all the NO2
urban background observed ratios evaluated in the present work (Table 1
NO2/NOx in the full WRF-Chem background and in the WRF-Chem background for the Modena urban area were also compared with observed concentration ratio at the nearest rural background site for the studied monitoring period: NO2/NOx in the full WRF-Chem background resulted comparable, while NO2/NOx in the WRF-Chem background higher also than this ratio (ca. 82.7%), confirming the large uncertainty that WRF-Chem has in reproducing NO2 concentrations in the urban environment of Modena.
The study focuses on NOx
observations in Modena and Reggio Emilia, two cities of the western-central Po Valley (Northern Italy), a European hotspot for NOx
, characterized by recurrent wind calm episodes [9
] and high-pressure conditions leading to long-lasting high concentrations also at remote rural sites. For the Modena case study, local background NOx
concentrations were also simulated by the WRF-Chem model taking into account two different scenarios. The first one considered the full set of the emissions in the TNO-MACC III inventory and the second one did not account for the contribution of the vehicular emissions in the urban area of Modena. This latter case was assessed in order to estimate the contribution of urban traffic in Modena to atmospheric concentrations.
In the first part of the study an analysis of measured concentrations at urban background and urban traffic sites, combined with Lagrangian dispersion modelling output from previous study, has been carried out. Results showed that despite for the Reggio Emilia case study the formation of extra secondary NO2 at the urban traffic site is negligible with respect to the urban background, the situation for the urban area of Modena is completely different. More in detail the NO2/NOx measured ratio at urban background station in Modena is very similar with the ΔNO2/ΔNOx ratio obtained by differentiating measured concentrations at traffic and background sites, suggesting that observations at both the locations (background and traffic areas) originates from similar pollution sources. Furthermore, the same outcomes highlighted the role of local weather conditions in affecting large contribution of secondary NO2 also at the urban traffic sites, so much to determine complete pollutant homogenization in the whole urban area.
In the second section of the manuscript, modelled WRF-Chem concentrations accounting for the full set of emissions were compared with observations at urban and rural sites to test the capability of the model in reproducing the observed trend. At rural background stations, despite a general underestimation of the observations, modelled concentrations were on average simulated reasonably well for both NOx and NO2, with statistical metrics in line with reference benchmark values for rural dispersion modelling. At urban traffic site, hourly simulated NOx concentrations exhibited a good agreement with observation notwithstanding the latter tended to be underestimated (NMB equal to −23% and r = 0.34). Other statistical metrics such as FB, NMSE, NAD and FAC2 fulfilled the acceptance criteria proposed in literature for dispersion modelling in urban environment. As far modelled NO2 concentrations are concerned, even though the NMSE, NAD and FAC2 statistical scores fulfilled the reference acceptance criteria, simulated concentrations presented a significant positive bias corresponding to a NMB equal to +50%.
Due to the poor representativeness of modelled NO2 concentrations at urban environment, additional analyses were mainly conducted for NOx concentrations. In particular, the second evaluation focused on the inter-comparison between the two WRF-Chem simulations accounting for different set of emissions. NOx simulated without the contribution of traffic emissions in Modena, represented a very small fraction of the urban background observation (28.6%), in contrast with the 76.8% of the full emissions run for the same location, confirming as the difference between the two (48.2%) is consistent with local emission inventory for traffic emissions (56% of the total NOx emissions). In addition, the reduction of the Pearson correlation coefficient between modelled and measured time series between the two simulations (respectively r = 0.34 and r = 0.23) pointed out the relevance of traffic emissions also at the urban background station, confirming the findings of the observation analysis.
Finally, the bias in the modelling results for NO2 from both WRF-Chem simulations limits thorough considerations regarding origin and amount of secondary NO2 in Modena, and an improved application of this model is needed to better investigate the role of traffic emissions in this urban area.