Next Article in Journal
In Silico and In Vitro Anti-Helicobacter Pylori Effects of Combinations of Phytochemicals and Antibiotics
Next Article in Special Issue
Simultaneous Quantitative Analysis of Six Isothiazolinones in Water-Based Adhesive Used for Food Contact Materials by High-Performance Liquid Chromatography–Tandem Mass Spectrometry (HPLC–MS/MS)
Previous Article in Journal
Fabrication of pH-Sensitive Tetramycin Releasing Gel and Its Antibacterial Bioactivity against Ralstonia solanacearum
Previous Article in Special Issue
Identification and Migration Studies of Photolytic Decomposition Products of UV-Photoinitiators in Food Packaging
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Migration Studies of Two Common Components of UV-curing Inks into Food Simulants

by
Miguel A. Lago
1,
Raquel Sendón
1,
Juana Bustos
2,
María T. Nieto
2,
Perfecto Paseiro Losada
1 and
Ana Rodríguez-Bernaldo de Quirós
1,*
1
Department of Analytical Chemistry, Nutrition and Food Science, Faculty of Pharmacy, University of Santiago de Compostela, E-15782 Santiago de Compostela, Spain
2
National Food Center, Spanish Agency of Food Safety and Nutrition, E-28220 Majadahonda, Spain
*
Author to whom correspondence should be addressed.
Molecules 2019, 24(19), 3607; https://doi.org/10.3390/molecules24193607
Submission received: 30 July 2019 / Revised: 25 September 2019 / Accepted: 4 October 2019 / Published: 7 October 2019
(This article belongs to the Special Issue Food Packaging Materials)

Abstract

The Rapid Alert System for Food and Feed (RASFF) has reported many cases of different UV curing inks components in foodstuffs during the last few years. These contaminants reach foodstuffs mainly by set-off, their principal migration mechanism from the package. Under this premise, this work has tried to characterize the process of migration of two common UV ink components: a photoinitiator (4-Methylbenzophenone) and a coinitiator (Ethyl-4-(dimethylamino) benzoate), from the most common plastic material used in food packaging low-density polyethylene (LDPE) into six different food simulants. The migration kinetics tests were performed at four different common storage temperatures, obtaining the key migration parameters for both molecules: the coefficients of diffusion and partition. The migration process was highly dependent on the storage conditions, the photoinitiator properties and the pH of the foodstuff.
Keywords: migration; 4-methylbenzophenone; ethyl-4-(dimethylamino) benzoate; diffusion coefficient; partition coefficient migration; 4-methylbenzophenone; ethyl-4-(dimethylamino) benzoate; diffusion coefficient; partition coefficient

Share and Cite

MDPI and ACS Style

Lago, M.A.; Sendón, R.; Bustos, J.; Nieto, M.T.; Paseiro Losada, P.; Rodríguez-Bernaldo de Quirós, A. Migration Studies of Two Common Components of UV-curing Inks into Food Simulants. Molecules 2019, 24, 3607. https://doi.org/10.3390/molecules24193607

AMA Style

Lago MA, Sendón R, Bustos J, Nieto MT, Paseiro Losada P, Rodríguez-Bernaldo de Quirós A. Migration Studies of Two Common Components of UV-curing Inks into Food Simulants. Molecules. 2019; 24(19):3607. https://doi.org/10.3390/molecules24193607

Chicago/Turabian Style

Lago, Miguel A., Raquel Sendón, Juana Bustos, María T. Nieto, Perfecto Paseiro Losada, and Ana Rodríguez-Bernaldo de Quirós. 2019. "Migration Studies of Two Common Components of UV-curing Inks into Food Simulants" Molecules 24, no. 19: 3607. https://doi.org/10.3390/molecules24193607

APA Style

Lago, M. A., Sendón, R., Bustos, J., Nieto, M. T., Paseiro Losada, P., & Rodríguez-Bernaldo de Quirós, A. (2019). Migration Studies of Two Common Components of UV-curing Inks into Food Simulants. Molecules, 24(19), 3607. https://doi.org/10.3390/molecules24193607

Article Metrics

Back to TopTop