Search Results (144)

Brain ischemia is a severe condition caused by reduced cerebral blood flow, leading to the disruption of ion gradients in brain tissue. This imbalance triggers spreading depolarizations, which are waves of neuronal and glial depolarization propagating through the gray matter. Microelectrode arrays (MEAs) are essential for real-time monitoring of these electrophysiological processes both in vivo and in vitro, but their sensitivity and signal quality are critical for accurate detection of extracellular brain activity. In this study, we evaluate the performance of a flexible microelectrode array based on gold-coated zinc oxide nanorods (ZnO NRs), referred to as nano-fMEA, specifically for high-fidelity electrophysiological recording under pathological conditions. Acute mouse brain slices were tested under two ischemic models: oxygen–glucose deprivation (OGD) and hyperkalemia. The nano-fMEA demonstrated significant improvements in event detection rates and in capturing subtle fluctuations in neural signals compared to flat fMEAs. This enhanced performance is primarily attributed to an optimized electrode–tissue interface that reduces impedance and improves charge transfer. These features enabled the nano-fMEA to detect weak or transient electrophysiological events more effectively, making it a valuable platform for investigating neural dynamics during metabolic stress. Overall, the results underscore the promise of ZnO NRs in advancing electrophysiological tools for neuroscience research. Full article

This research examines the effect of annealing temperature on the growth orientation of zinc oxide (ZnO) nanorods and its subsequent influence on NO₂ gas sensing efficiency. Zinc oxide (ZnO) nanorods were synthesized using the chemical bath deposition method, followed by annealing at 300, 400, and 500 °C. Diffraction analysis confirmed that both non-annealed and annealed ZnO nanorods crystallize in a hexagonal wurtzite structure. However, increasing the annealing temperature shifts the growth orientation from the c-axis (002) toward the (100) and (101) directions. Microscopy images (FE-SEM) revealed a reduction in nanorod diameter as the annealing temperature increases. Optical characterization using UV–visible and photoluminescence spectroscopy indicated shifts in the band gap energy and emission properties. Contact angle measurements demonstrated the hydrophobic nature of the films. Gas sensing tests at 200 °C revealed that the ZnO thin film annealed at 400 °C achieved the highest NO₂ response of 5.88%. The study highlights the critical role of annealing in modifying the crystallinity, growth orientation, and defect states of ZnO thin films, ultimately enhancing their NO₂ detection capability. Full article

The currently used electrical energy devices for portable applications are in limited life and need of frequent recharging, it is a big bottleneck for wireless and transportation systems. The scientific community is motivated to find innovative and efficient devices to convert environmental energy into useful forms. Nanogenerator can mitigate this issue by harvesting ambient energy of different forms into useful electrical energy. Particularly flexible nanogenerators can efficiently convert ambient mechanical energy into electrical energy which can be fruitfully used for self-powered sensors and electronic appliances. Zinc oxide is an interesting photosensitive and piezoelectric material that is expected to play a vital role in the synergetic harvesting of environmental thermal, sound, mechanical, and solar energies. As ZnO can be synthesized using easy methods and materials at low cost, the conversion efficiencies of solar and other energy forms can increase considerably. ZnO is a versatile material with interesting semiconducting, optical, and piezoelectric properties; it can be used advantageously to harvest more than one type of ambient energy. The coupled semiconducting and piezoelectric properties of ZnO are attractive for fabricating nanogenerators capable of harvesting both ambient optical and mechanical energies simultaneously. These nanolevel conversion devices are much required to power remote and implantable devices without the need for additional power sources. The present review briefly discusses the principles and mechanisms of different energy harvesting abilities of ZnO nanorods and their composites by consolidating available literature. In addition, the developments taking place in nanogenerators of different kinds—such as photovoltaic, piezoelectric, pyroelectric, and triboelectrics for self-powered technology—and their progress in hybrid energy harvesting application is reviewed. Full article

This study presents the development of a zinc oxide (ZnO) nanorod-based sensor for the detection and quantification of residual pesticides commonly found in tea plantations, with a focus on quinalphos and thiamethoxam. Exploiting the unique electrical characteristics of ZnO nanorods, the sensor exhibits high sensitivity and selectivity in monitoring trace levels of pesticide residues. The detection mechanism relies on measurable changes in electrical resistance when the ZnO nanorod-coated electrodes interact with varying concentrations of the target pesticides. A performance evaluation was carried out using water samples spiked with different pesticide concentrations. The sensor displayed distinct response profiles for each compound: a linear resistance–concentration relationship for quinalphos and a non-linear, saturating trend for thiamethoxam, reflecting their differential interactions with the ZnO surface. Statistical analysis confirmed the sensor’s reliability, reproducibility, and consistency across repeated measurements. The rapid response time and ease of fabrication underscore its potential for real-time, on-site pesticide monitoring. This method offers a promising alternative to traditional analytical techniques, enhancing food safety assurance and supporting sustainable agricultural practices through effective environmental surveillance. Full article

In this study, to enhance the output performance of a contact-separation mode triboelectric nanogenerator (TENG), a zinc oxide nanorod (ZnO NR) film with piezoelectric properties was integrated into a Polydimethylsiloxane (PDMS) film as the dielectric layer. The working mechanism of the PDMS-ZnO NR-based TENG was theoretically analyzed in two stages: charge transfer during contact electrification on the material surface and charge movement in the electrostatic induction process. The output characteristics of the PDMS-ZnO NR-based TENG were investigated and compared with those of a PDMS-based TENG. The experimental results demonstrate that the PDMS-ZnO NR-based TENG reached an open-circuit voltage of 39.34 V, representing an increase of 64.5% compared to the PDMS-based TENG. The maximum output power of a 4 cm × 4 cm PDMS-ZnO NR-based TENG reached 82.2 μW. Using a specially designed energy-harvesting circuit, the generated electrical energy was stored in a capacitor, which was charged to 1.47 V within 1 min and reached 3 V in just 2.78 min. This voltage was sufficient to power over 20 LEDs and small sensors. Additionally, the TENG was integrated into the sole of footwear, where the electrical signals generated by compression could be utilized for step counting and gait analysis. Full article

Flexible and wearable electronics often rely on piezoelectric materials, and Poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) membranes are popular for this application. However, their electromechanical performance is limited due to a relatively low piezoelectric coefficient. To address this, this study investigates the incorporation of zinc oxide (ZnO) nanorods (NRs) into a P(VDF-TrFE) nanofiber membrane matrix. ZnO NRs were synthesized and doped into well-aligned P(VDF-TrFE) nanofibers using electrospinning with a high-speed rotating drum. The impact of ZnO NRs’ mass fraction on the piezoelectric properties of the membranes was evaluated. Results show that a maximum piezoelectric coefficient ($d_{33}$) of −62.4 pC/N, 9.5 times higher than neat P(VDF-TrFE), was achieved. These enhanced membranes demonstrated excellent performance in finger-tapping and bending detection, making them promising for large-scale flexible sensor applications in wearable electronics. This approach offers a simple and effective route to improve the performance of piezoelectric materials in flexible devices. Full article

The development of state-of-the-art gas sensors based on metal oxide semiconductors (MOS) to monitor hazardous and greenhouse gas (e.g., methane, CH₄, and carbon dioxide, CO₂) has been significantly advanced. Moreover, the morphological and topographical structures of MOSs have significantly influenced the gas sensors by means of surface catalytic activities. This work examines the impact of morphological and topological networked assembly of zinc oxide (ZnO) nanostructures, including microparticles and nanoparticles (0D), nanowires and nanorods (1D), nanodisks (2D), and hierarchical networks of tetrapods (3D). Gas sensors consisting of vertically aligned ZnO nanorods (ZnO–NR) and topologically interconnected tetrapods (T–ZnO) of varying diameter and arm thickness synthesized using aqueous phase deposition and flame transport method on interdigitated Pt electrodes are evaluated for methane detection. Smaller-diameter nanorods and tetrapod arms (nanowire-like), having higher surface-to-volume ratios with reasonable porosity, exhibit improved sensing behavior. Interestingly, when the nanorods’ diameter and interconnected tetrapod arm thickness were comparable to the width of the depletion layer, a significant increase in sensitivity (from 2 to 30) and reduction in response/recovery time (from 58 s to 5.9 s) resulted, ascribed to rapid desorption of analyte species. Additionally, nanoparticles surface-catalyzed with Pd (~50 nm) accelerated gas sensing and lowered operating temperature (from 200 °C to 50 °C) when combined with UV photoactivation. We modeled the experimental findings using a modified general formula for ZnO methane sensors derived from the catalytic chemical reaction between methane molecules and oxygen ions and considered the structural surface-to-volume ratios (S/V) and electronic depletion region width (L_d) applicable to other gas sensors (e.g., SnO₂, TiO₂, MoO₃, and WO₃). Finally, the effects of UV light excitation reducing detection temperature help to break through the bottleneck of ZnO-based materials as energy-saving chemiresistors and promote applications relevant to environmental and industrial harmful gas detection. Full article

The burgeoning field of biosensors has seen significant advancements with the induction of zinc oxide (ZnO) nanostructures, because of their unique structural, electrical, and optical properties. ZnO nanostructures provide numerous benefits for biosensor applications. Their superior electron mobility enables effective electron transfer between the bioreceptor and transducer, enhancing sensitivity and reducing detection limits. Furthermore, ZnO’s biocompatibility and non-toxicity make it ideal for in vivo applications, reducing the chances of adverse biological responses. This review paper explores the prospects of ZnO nanostructures in the development of biosensors, focusing on their morphological and structural characteristics. Various synthesis techniques, that include sol-gel, sputtering, and chemical vapor deposition, were successfully employed to prepare different ZnO nanostructures, like nanorods, nanotubes, and nanowires. The various findings in this field underscore the efficacy of ZnO nanostructures in enhancing the specificity and sensitivity of biosensors, presenting a promising avenue for the advancement of point-of-care diagnostic devices. Full article

Zinc oxide nanoparticles (ZnO NPs) were synthesized using a simple and eco-friendly precipitation method, employing a capping agent derived from chia seeds (Salvia hispanica). X-ray diffraction (XRD) analysis confirmed the formation of ZnO with a hexagonal crystal structure and an average crystallite size of less than 30 nm. Scanning electron microscopy (SEM) revealed distinct quasi-spherical and nanorod-like morphologies, while energy-dispersive X-ray spectroscopy (EDX) verified the presence of zinc and oxygen. Diffuse reflectance spectroscopy (DRS) indicated significant activity in the UV region, with the nanoparticles exhibiting a band gap of 3.25 eV. The photocatalytic efficiency of the synthesized ZnO NPs was evaluated through their ability to degrade diclofenac sodium (DCF) and para-nitrophenol (4-nitrophenol, PNP) under UV-LED irradiation, achieving pollutant removal rates exceeding 98%. The degradation mechanism is clarified by a detailed characterization of the reaction intermediates. These findings highlight the potential of ZnO NPs synthesized from chia seed extract for effective environmental remediation of pharmaceutical and organic pollutants. Full article

Zinc oxide, due to its unique physicochemical properties, including dual piezoelectric and semiconductive ones, demonstrates a high application potential in various fields, with a particular focus on nanotechnology. Among ZnO nanoforms, nanorods are gaining particular interest. Due to their ability to efficiently transport charge carriers and photoelectric properties, they demonstrate significant potential in energy storage and conversion, as well as photovoltaics. They can be prepared via various methods; however, most of them require large energy inputs, long reaction times, or high-cost equipment. Hence, new methods of ZnO nanorod fabrication are currently being sought out. In this paper, an ultrasound-supported synthesis of ZnO nanorods with zinc acetate as a zinc precursor has been described. The fabrication of nanorods included the treatment of the precursor solution with ultrasounds, wherein various sonication times were employed to verify the impact of the sonication process on the effectiveness of ZnO nanorod synthesis and the sizes of the obtained nanostructures. The morphology of the obtained ZnO nanorods was imaged via a scanning electron microscope (SEM) analysis, while the particle size distribution within the precursor suspensions was determined by means of dynamic light scattering (DLS). Additionally, the dynamic viscosity of precursor suspensions was also verified. It was demonstrated that ultrasounds positively affect ZnO nanorod synthesis, yielding longer nanostructures through even reactant distribution. Longer nanorods were obtained as a result of short sonication (1–3 min), wherein prolonged treatment with ultrasounds (4–5 min) resulted in obtaining shorter nanorods. Importantly, the application of ultrasounds increased particle homogeneity within the precursor suspension by disintegrating particle agglomerates. Moreover, it was demonstrated that ultrasonic treatment reduces the dynamic viscosity of precursor suspension, facilitating faster particle diffusion and promoting a more uniform growth of longer ZnO nanorods. Hence, it can be concluded that ultrasounds constitute a promising solution in obtaining homogeneous ZnO nanorods, which is in line with the principles of green chemistry. Full article

Zinc oxide and titanium dioxide are materials with strong photocatalytic and antimicrobial activity. This activity is greater when the material is in nanocrystalline form. It has been seen that these properties are also present in the ZnO-TiO₂ nanocomposite material, and the extent depends on multiple factors, such as crystallinity, structural composition, crystallite size, and morphology. These structural properties can be varied by acting on the synthesis of the material, obtaining a wide variety of composites: random nanoparticles, nanorods, nanowires, nanotubes, nanofibers, tetrapods, core–shell, hollow spheres, inverse opal structures (IOSs), hierarchical structures, and films. When an interface between nanocrystallites of the two oxides is created, the composite system manages to have photocatalytic activity greater than that of the two separate oxides, and in certain circumstances, even greater than P25. The antimicrobial activity results also improved for the composite system compared to the two separate oxides. These two aspects make these materials interesting in various fields, such as wastewater and air treatment, energy devices, solar filters, and pharmaceutical products and in the context of the restoration of monumental cultural assets, in which their use has a preventive purpose in the formation of biofilms. In this review we analyse the synthesis techniques of ZnO-TiO₂ nanocomposites, correlating them to the shape obtained, as well as the photocatalytic and antimicrobial activity. It is also illustrated how ZnO-TiO₂ nanocomposites can have a less negative impact on toxicity for humans and the environment compared to the more toxic ZnO nanoparticles or ZnO. Full article

The optical characteristics and electrical behavior of zinc oxide nanorods (ZnO-NRs) and silver nanoparticles (Ag-NPs) were investigated using advanced scanning probe microscopy techniques. The study revealed that the ZnO nanorods had a length of about 350 nm, while the Ag nanoparticles were spherical with heights ranging from 5 to 14 nm. Measurements with Kelvin probe force microscopy (KPFM) showed that the work functions of ZnO nanorods were approximately 4.55 eV, higher than that of bulk ZnO, and the work function of Ag nanoparticles ranged from 4.54 to 4.56 eV. The electrical characterization of ZnO nanorods, silver nanoparticles, and their hybrid was also conducted using conductive atomic force microscopy (C-AFM) to determine the local current-voltage (I-V) characteristics, which revealed a characteristic similar to that of a Schottky diode. The current-voltage characteristic curves of ZnO nanorods and Ag nanoparticles both showed an increase in current at around 1 V, and the hybrid ZnONRs/AgNP exhibited an increase in turn-on voltage at around 2.5 volts. This suggested that the presence of Ag nanoparticles enhanced the electrical properties of ZnO nanorods, improving the charge carrier mobility and conduction mechanisms through a Schottky junction. The investigation also explored the optical properties of ZnO-NRs, AgNPs, and their hybrid, revealing absorption bands at 3.11 eV and 3.18 eV for ZnO-NRs and AgNPs, respectively. The hybrid material showed absorption at 3.13 eV, indicating enhanced absorption, and the presence of AgNP affected the optical properties of ZnO-NR, resulting in increased photoluminescence intensity and slightly changes in peak positions. Full article

Photodetectors and gas sensors are vital in modern technology, spanning from environmental monitoring to biomedical diagnostics. This paper explores the UV detection and gas sensing properties of a zinc oxide (ZnO) nanorod array (ZNA) grown on silver nanowire mesh (AgNM) using a hydrothermal method. We examined the impact of different zinc acetate precursor concentrations on their properties. Results show the AgNM forms a network with high transparency (79%) and low sheet resistance (7.23 Ω/□). A sol–gel ZnO thin film was coated on this mesh, providing a seed layer with a hexagonal wurtzite structure. Increasing the precursor concentration alters the diameter, length, and area density of ZNAs, affecting their performance. The ZNA-AgNM-based photodetector shows enhanced dark current and photocurrent with increasing precursor concentration, achieving a maximum photoresponsivity of 114 A/W at 374 nm and a detectivity of 6.37 × 10¹⁴ Jones at 0.05 M zinc acetate. For gas sensing, the resistance of ZNA-AgNM-based sensors decreases with temperature, with the best hydrogen response (2.71) at 300 °C and 0.04 M precursor concentration. These findings highlight the potential of ZNA-AgNM for high-performance UV photodetectors and hydrogen gas sensors, offering an alternative way for the development of future sensing devices with enhanced performance and functionality. Full article

This study explores the enhancement of silicon-based solar cell performance and durability through the application of zinc oxide (ZnO) nanocomposite film coatings. Utilizing the sol–gel method, ZnO nanorods were synthesized and dispersed within a polyvinyl butyral (PVB) matrix, resulting in uniform nanocomposite films. Comprehensive characterization using X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), UV-Visible spectroscopy, and contact angle measurements confirmed the effective integration and desirable properties of ZnO within the PVB matrix. The ZnO coatings demonstrated superior UV absorptivity, significantly blocking UV radiation at 355 nm while maintaining high transparency in the visible range. This led to improvements in key photovoltaic parameters, including short circuit current (J_sc), open-circuit voltage (V_oc), efficiency (η), and fill factor (FF). Although a minor reduction in Isc was observed due to the ZnO layer’s influence on the light absorption spectrum, the overall efficiency and fill factor experienced notable enhancements. Furthermore, the thermal load on the solar cells was effectively reduced, mitigating UV-induced degradation and thereby prolonging the operational lifespan of the solar panels. Under damp heat conditions, the coated solar panels exhibited remarkable durability compared to their uncoated counterparts, underscoring the protective advantages of ZnO films. These findings highlight the potential of ZnO nanocomposite coatings to significantly boost the efficiency, reliability, and longevity of silicon-based solar panels, making them more viable for long-term deployment in diverse environmental conditions. Full article

Hot water treatment (HWT) is a versatile technique for synthesizing metal oxide nanostructures (MONSTRs) by immersing metal substrates in hot water, typically in glass beakers. The proximity of substrates to the heat source during HWT can influence the temperature of the substrate and subsequently impact MONSTR growth. In our study, zinc (Zn) substrates underwent HWT at the base of a glass beaker in contact with a hot plate and at four different vertical distances from the base. While the set temperature of deionized (DI) water was 75.0 °C, the substrate locations exhibited variations, notably with the base reaching 95.0 °C. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and Raman spectroscopy showed stoichiometric and crystalline zinc oxide (ZnO) nanorods. ZnO rods on the base, exposed to higher temperatures, displayed greater growth in length and diameter, and higher crystallinity. Nanorods with increasing vertical distances from the base exhibited a logarithmic decrease in length despite identical temperatures, whereas their diameters remained constant. We attribute these findings to crucial HWT growth mechanisms like surface diffusion and “plugging”, influenced by temperature and water flow within the beaker. Our results provide insights for optimizing synthesis parameters to effectively control MONSTR growth through HWT. Full article