Search Results (50)

Firstly, this paper reviews the fundamental theories of solid surface wettability and contact angle hysteresis. Subsequently, it further introduces four typical wettability-engineered surfaces with low hysteresis (superhydrophobic, superamphiphobic, super-slippery, and liquid-like smooth surfaces). Finally, it focuses on the latest research progress in the field of droplet manipulation on open planar surfaces with engineered wettability. To achieve droplet manipulation, the core driving forces primarily stem from natural forces guided by bioinspired gradient surfaces or the regulatory effects of external fields. In terms of bioinspired self-propelled droplet movement, this paper summarizes research inspired by natural organisms such as desert beetles, cacti, self-aligning floating seeds of emergent plants, or water-walking insects, which construct bioinspired special gradient surfaces to induce Laplace pressure differences or wettability gradients on both sides of droplets for droplet manipulation. Moreover, this paper further analyzes the mechanisms, advantages, and limitations of these self-propelled approaches, while summarizing the corresponding driving force sources and their theoretical formulas. For droplet manipulation under external fields, this paper elaborates on various external stimuli including electric fields, thermal fields, optical fields, acoustic fields, and magnetic fields. Among them, electric fields involve actuation mechanisms such as directly applied electrostatic forces and indirectly applied electrocapillary forces; thermal fields influence droplet motion through thermoresponsive wettability gradients and thermocapillary effects; optical fields cover multiple wavelengths including near-infrared, ultraviolet, and visible light; acoustic fields utilize horizontal and vertical acoustic radiation pressure or acoustic wave-induced acoustic streaming for droplet manipulation; the magnetic force acting on droplets may originate from their interior, surface, or external substrates. Based on these different transport principles, this paper comparatively analyzes the unique characteristics of droplet manipulation under the five external fields. Finally, this paper summarizes the current challenges and issues in the research of droplet manipulation on the open planar surfaces and provides an outlook on future development directions in this field. Full article

This study presents a bioinspired phase-change transparent flexible heater (PTFH) for programmable droplet manipulation under ultralow voltage. By embedding a self-junctioned copper nanowire network into paraffin-infused, porous PVDF-HFP gel matrices, the PTFH achieves rapid, non-contact, and reversible control of microdroplet mobility. The PTFH can be bent or tailored into diverse shapes (e.g., V/X configurations), enabling multidirectional droplet transport. Under ultralow voltage actuation (<1 V), the surface of PTFH melts the phase-change lubricant within 2 s, switching surface wettability from high adhesion (Wenzel state) to low adhesion (SLIPS state). By combining Laplace pressure and temperature gradients (up to 22 °C/mm), drive droplets at ~2.0 mm/s over distances of ~13.9 mm. Programmable droplet coalescence, curved-surface transport, and a microreactor design for batch reactions were also demonstrated. The PTFH exhibits excellent transparency (89% when activated), mechanical flexibility, and cyclic stability, offering a versatile platform for microreactors, microengines, and smart windows. Full article

Ice accumulation on cold surfaces presents significant operational and safety challenges in various fields such as power transmission, aviation, and polar marine transportation. This study investigates the effectiveness of selectively applied superhydrophobic patterns on hydrophilic substrates to locally control freezing behaviors. The freezing dynamics of water droplets impacting surfaces with hybrid wettability patterns were investigated experimentally under cold conditions. The results demonstrate that superhydrophobic surfaces significantly reduce the freezing rate due to decreased contact time and the contact region. By selectively placing superhydrophobic patterns on hydrophilic surfaces, the location of ice formation could be effectively manipulated. The use of multiple superhydrophobic stripes was found to segment the impacting droplets into several parts, implying the ability to selectively avoid ice accumulation at specific areas. Furthermore, experiments identified critical temperature thresholds at which the effectiveness of superhydrophobic stripes diminishes. When the temperature of the substrate is higher than −25 °C, the superhydrophobic stripes can sufficiently divide an impacting droplet leaving no ice at the superhydrophobic region. In the tested temperature range between −25 °C and −40 °C, the ice coverage ratio at the superhydrophobic region increases as temperature decreases, with a maximum value of 25.6 ± 2.33% at −40 °C. Superhydrophobic patterns also exhibited improved deicing efficiency during melting processes, highlighting their potential for robust ice management applications. Full article

In this paper, the synthesis of TiC-coated carbon fibers (TiC-CFs) with varying thicknesses is achieved through the manipulation of the molten salt reaction, along with the fabrication of TiC-coated carbon fiber-reinforced aluminum matrix (TiC-CF/Al) composites via the vacuum pressure infiltration technique. The results show that modulating the holding time of the molten salt reaction significantly enhances the wettability between the carbon fiber (CF) and the aluminum, thereby augmenting the mechanical integrity of the composite materials. Should the holding time be excessively short, the coating on the CF surface develops an uneven distribution, and its efficacy in obstructing the direct interaction with the aluminum is inadequate. As the holding time prolongs, the TiC coating thickens, achieving a comprehensive coverage after 2 h of holding. The presence of a pristine TiC coating on the CF surface not only optimizes the wettability with the aluminum melt but also mitigates the reaction between the CF and aluminum. However, an excessively thick coating not only reduces the strength of the fibers, due to excessive reactions, but also makes the coating prone to detachment during the preparation process due to stress. At a holding time of 3 h, the tensile strength of the CF/Al composite material reaches its highest value, with a tensile strength of 103.93 MPa and an impressive 72.35% enhancement over that of the aluminum. Full article

Nature provides us with a wealth of inspiration for the design of bionic functional surfaces. Numerous types of plant leaves with exceptional wettability, anisotropy, and adhesion are extensively employed in many engineering applications. Inspired by the wettability, anisotropy, and adhesion of indocalamus leaves, bionic upper and lower surfaces (BUSs and BLSs) of the indocalamus leaf were successfully prepared using a facile approach combining laser scanning and chemical modification. The results demonstrated the BUSs and BLSs obtained similar structural features to the upper and lower surfaces of the indocalamus leaf and exhibited enhanced and more-controllable wettability, anisotropy, and adhesion. More importantly, we conducted a detailed comparative analysis of the wettability, anisotropy, and adhesion between BUSs and BLSs. Finally, BUSs and BLSs were also explored for the corresponding potential applications, including self-cleaning, liquid manipulation, and fog collection, thereby broadening their practical utility. We believe that this study can contribute to the enrichment of the research on novel biological models and provide significant insights into the development of multifunctional bionic surfaces. Full article

Over the last decade, researchers have developed a variety of new analytical and clinical diagnostic devices. These devices are predominantly based on microfluidic technologies, where biological samples can be processed and manipulated for the collection and detection of important biomolecules. Polydimethylsiloxane (PDMS) is the most commonly used material in the fabrication of these microfluidic devices. However, it has a hydrophobic nature (contact angle with water of 110°), leading to poor wetting behavior and issues related to the mixing of fluids, difficulties in obtaining uniform coatings, and reduced efficiency in processes such as plasma separation and molecule detection (protein adsorption). This work aimed to consider the fabrication aspects of PDMS microfluidic devices for biological applications, such as surface modification methods. Therefore, we studied and characterized two methods for obtaining hydrophilic PDMS surfaces: surface modification by bulk mixture and the surface immersion method. To modify the PDMS surface properties, three different surfactants were used in both methods (Pluronic^® F127, polyethylene glycol (PEG), and polyethylene oxide (PEO)) at different percentages. Water contact angle (WCA) measurements were performed to evaluate the surface wettability. Additionally, capillary flow studies were performed with microchannel molds, which were produced using stereolithography combined with PDMS double casting and replica molding procedures. A PDMS microfluidic device for blood plasma separation was also fabricated by soft lithography with PDMS modified by PEO surfactant at 2.5% (v/v), which proved to be the best method for making the PDMS hydrophilic, as the WCA was lower than 50° for several days without compromising the PDMS’s optical properties. Thus, this study indicates that PDMS surface modification shows great potential for enhancing blood plasma separation efficiency in microfluidic devices, as it facilitates fluid flow, reduces cell aggregations and the trapping of air bubbles, and achieves higher levels of sample purity. Full article

Polymers are essential in several sectors, yet some applications necessitate surface modification. One practical and eco-friendly option is non-thermal plasma exposure. The present research endeavors to examine the impacts of dielectric barrier discharge atmospheric pressure plasma on the chemical composition and wettability properties of acrylonitrile butadiene styrene surfaces subject to the action of additive manufacturing. The plasma source was produced by igniting either helium or argon and then adjusted to maximize the operational conditions for exposing polymers. The drop in contact angle and the improvement in wettability after plasma exposure can be due to the increased oxygen-containing groups onto the surface, together with a reduction in carbon content. The research findings indicated that plasma treatment significantly improved the wettability of the polymer surface, with an increase of up to 60% for both working gases, while the polar index increased from 0.01 up to 0.99 after plasma treatment. XPS measurements showed an increase of up to 10% in oxygen groups at the surface of He–plasma-treated samples and up to 13% after Ar–plasma treatment. Significant modifications were observed in the structure that led to a reduction of its roughness by 50% and also caused a leveling effect after plasma treatment. A slight decrease in the glass and melting temperature after plasma treatment was pointed out by differential scanning calorimetry and broadband dielectric spectroscopy. Up to a 15% crystallinity index was determined after plasma treatment, and the 3D printing process was measured through X-ray diffraction. The empirical findings encourage the implementation of atmospheric pressure plasma-based techniques for the environmentally sustainable manipulation of polymers for applications necessitating higher levels of adhesion and specific prerequisites. Full article

The energy state of endosteal implants is dependent on the material, manufacturing technique, cleaning procedure, sterilization method, and surgical manipulation. An implant surface carrying a positive charge renders hydrophilic properties, thereby facilitating the absorption of vital plasma proteins crucial for osteogenic interactions. Techniques to control the surface charge involve processes like oxidation, chemical and topographical adjustments as well as the application of nonthermal plasma (NTP) treatment. NTP at atmospheric pressure and at room temperature can induce chemical and/or physical reactions that enhance wettability through surface energy changes. NTP has thus been used to modify the oxide layer of endosteal implants that interface with adjacent tissue cells and proteins. Results have indicated that if applied prior to implantation, NTP strengthens the interaction with surrounding hard tissue structures during the critical phases of early healing, thereby promoting rapid bone formation. Also, during this time period, NTP has been found to result in enhanced biomechanical fixation. As such, the application of NTP may serve as a practical and reliable method to improve healing outcomes. This review aims to provide an in-depth exploration of the parameters to be considered in the application of NTP on endosteal implants. In addition, the short- and long-term effects of NTP on osseointegration are addressed, as well as recent advances in the utilization of NTP in the treatment of periodontal disease. Full article

Chemical instability of liquid-repellent surfaces is one of the nontrivial hurdles that hinders their real-world applications. Although much effort has been made to prepare chemically durable liquid-repellent surfaces, little attention has been paid to exploit the instability for versatile use. Herein, we propose to create hydrophilic patterns on a superhydrophobic surface by taking advantage of its chemical instability induced by acid solution treatment. A superhydrophobic Cu(OH)₂ nanoneedle-covered Cu plate that shows poor stability towards HCl solution (1.0 M) is taken as an example. The results show that 2.5 min of HCl solution exposure leads to the etching of Cu(OH)₂ nanoneedles and the partial removal of the self-assembled fluoroalkyl silane molecular layer, resulting in the wettability transition from superhydrophobocity to hydrophilicity, and the water contact angle decreases from ~160° to ~30°. Hydrophilic dimples with different diameters are then created on the superhydrophobic surfaces by depositing HCl droplets with different volumes. Afterwards, the hydrophilic dimple-patterned superhydrophobic surfaces are used for water droplet manipulations, including controlled transfer, merging, and nanoliter droplet deposition. The results thereby verify the feasibility of creating wettability patterns on superhydrophobic surfaces by using their chemical instability towards corrosive solutions, which broadens the fabrication methods and applications of functional liquid-repellent surfaces. Full article

The performance of carbon geo-sequestration is influenced by several parameters, such as the heterogeneity of the reservoir, the characteristics of the caprock, the wettability of the rock, and the salinity of the aquifer brine. Although many characteristics, like the formation geology, are fixed and cannot be altered, it is feasible to choose and manipulate other parameters in order to design an optimized storage programme such as the implementation of CO₂ injection techniques, including continuous injection or water alternating CO₂, which can significantly increase storage capacity and guarantee secure containment. Although WAG (water-alternating-gas) technology has been widely applied in several industrial sectors such as enhanced oil recovery (EOR) and CO₂ geo-sequestration, the impact of the CO₂-to-water ratio on the performance of CO₂ geo-sequestration in heterogeneous formations has not been investigated. In this study, we have constructed a 3D heterogeneous reservoir model to simulate the injection of water alternating gas in deep reservoirs. We have tested several CO₂-water ratios, specifically the 2:1, 1:1, and 1:2 ratios. Additionally, we have estimated the capacity of CO₂ trapping, as well as the mobility and migration of CO₂. Our findings indicate that injecting a low ratio of CO₂ to water (specifically 1:2) resulted in a much better performance compared to situations with no water injection and high CO₂-water ratios. The residual and solubility trappings were notably increased by 11% and 19%, respectively, but the presence of free mobile CO₂ was reduced by 27%. Therefore, in the reservoir under investigation, the lower CO₂-water ratio is recommended due to its improvement in CO₂ storage capacity and containment security. Full article

A significant growth of research on digital microfluidics has been achieved over the past several decades, and the field is still attracting increasing attention for fulfilling relevant mechanisms and potential applications. Numerous studies have been devoted to actively manipulating droplets in a variety of fundamental and applicational scenarios. In this work, the deformation of ferromagnetic fluid droplets is studied under an external uniform magnetic field. The droplets are precisely dispersed on the bottom surface of a container assembled with polymer methacrylate (PMMA) plates. Mineral oil is applied instead of air as the surrounding medium for easy stretching and preventing water solvent evaporation in ferrofluid. The design and processing of the container are firstly carried out to observe the shape and characterize the wettability of the droplets in the immiscible mineral oil medium. Furthermore, the droplets’ deformation and the working mechanism are given under the action of the horizontal uniform magnetic field. At different magnetic field intensities, the droplet is stretched in the horizontal direction parallel to the applied field. Due to volume conservation, the dimension in the height reduces correspondingly. With the coupling effect of magnetic force, viscous force and interfacial tension, the contact angle first increases with the magnetic field and then basically remains unchanged upon magnetization saturation. Consistent with the experimental results, the numerical method clearly reveals the field coupling mechanism and the nonlinear deformation of the sessile droplet. Full article

Splitting a droplet into several segments is of great significance in many applications such as the detection of tiny liquid samples, whereas the surface tension tends to hold liquid to remain as one drop, causing difficulty in separating the droplet into pieces. In this work, a method is proposed to split an impacting droplet with a relatively high velocity or Weber number into two halves by a superhydrophobic wire. The effects of the wire wettability and the impact velocity of the droplet on the splitting phenomena and the efficacy to an anti-icing application are investigated. Compared to a hydrophilic wire, a superhydrophobic wire splits an impacting droplet at a relatively high speed of the Weber number greater than 3.1 and inhibits ice accretion at the temperature as low as −20 °C. The results suggest that a superhydrophobic wire can be utilized in the droplet manipulation and anti-icing applications such as power lines in high latitude areas. Full article

Water collection remains a fundamental challenge to stable and efficient operation of the solar desalination system. Functional surfaces that can realize self-actuation of droplets have shown great potential in improving droplet dynamics without external energy. Therefore, a surface that can make a droplet move spontaneously along a curve was designed for smart droplet manipulation, and the mechanism of the droplet motion was revealed through molecular dynamics simulations. Influences of the wettability difference between the curved track and the background, the width of curved track, and the temperature were evaluated via simulations. The results show that the surface on which the curved track and the background are both hydrophobic enables a faster actuating velocity of the droplet than the hydrophilic-hydrophobic surface and the hydrophilic-hydrophilic surface. The width of the curved track also affects the actuating velocity of the droplet and increasing the TRACK width can increase the actuating velocity of the droplet. However, actuation of the droplet slows down if the width of the curved track is too large. Overall, the mechanism driving the motion of the droplet along the curve was investigated, which opens new opportunities for the application and manufacturing of water collection in solar desalination. Full article

Multifunctional super-repellent composite coatings play an important part in academic and industrial fields, while it is still a great challenge to effectively integrate a variety of functions into one material. Mg alloys having low density, high strength-to-weight ratio, and good shielding, are widely used in electronic devices, while it is susceptible to sever corrosion especially in moist air and ocean atmosphere. Here, a versatile superhydrophobic coating with organic-inorganic hybrid structure and hierarchical surface textures, integrating robust wettability with design manipulation is synthesized by assembling modified SiO₂ nanoparticles on polytetrafluoroethylene (PTFE) layer on the AZ31 Mg alloy. The composite coating has good water repellency with a contact angle of 170.5°, due to the micro/nano textures and low surface energy. The composite coating increases the corrosion potential of AZ31 Mg from −1.483 V to −1.243 V, and reduces the corrosion current density by 3 orders of magnitude. Remarkably, the superhydrophobic coating displays enticing damage-resistance (>40 cycles), superior environmental stability (thermal shock and outdoor placement) and self-cleaning function. Moreover, the composite coatings display excellent electrical properties with superior voltage resistance (>30 V/μm), and high resistivity (>10¹² Ω∙cm), as well the coating has a low dielectric constant (≈3.91) and dielectric loss (0.0094), which are great advantages for the electronic or electrical engineering applications. We expect that the versatile super-repellent coating can be used as candidates for novel advanced energy materials, especially in harsh environments. Full article

The rapid development of graphene-based nanotechnologies in recent years has drawn extensive attention in environmental applications, especially for water treatment. Three-dimensional graphene-based macrostructures (GBMs) have been considered to be promising materials for practical water purification due to their well-defined porous structure and integrated morphology, and displayed outstanding performance in pollutant abatement with easy recyclability. Three-dimensional GBMs could not only retain the intrinsic priorities of 2D graphene, but also emerge with extraordinary properties by structural manipulation, so rational design and construction of 3D GBMs with desirable microstructures are important to exploit their potential for water treatment. In this review, some important advances in surface modification (chemical doping, wettability, surface charge) and geometrical control (porous structure, oriented arrangement, shape and density) with respect to 3D GBMs have been described, while their applications in water purification including adsorption (organic pollutants, heavy metal ions), catalysis (photocatalysis, Fenton-like advanced oxidation) and capacitive desalination (CDI) are detailly discussed. Finally, future challenges and prospective for 3D GBMs in water purification are proposed. Full article