Search Results (10)

Calorimetry at the High Luminosity LHC (HL-LHC) faces many challenges, particularly in the forward direction, such as radiation tolerance and large in-time event pileup. To meet these challenges, the CMS Collaboration is preparing to replace its current endcap calorimeters from the HL-LHC era with a high-granularity calorimeter (HGCAL), featuring an unprecedented transverse and longitudinal segmentation, for both the electromagnetic and hadronic compartments, with 5D information (space–time–energy) read out. The proposed design uses silicon sensors for the electromagnetic section (with fluences above ${10}^{16} {\mathrm{n}}_{eq}{\mathrm{/cm}}^2$) and high-irradiation regions (with fluences above ${10}^{14} {\mathrm{n}}_{eq}{\mathrm{/cm}}^2$) of the hadronic section, while in the low-irradiation regions of the hadronic section, plastic scintillator tiles equipped with on-tile silicon photomultipliers (SiPMs) are used. Full HGCAL will have approximately 6 million silicon sensor channels and about 280 thousand channels of scintillator tiles. This will allow for particle-flow-type calorimetry, where the fine structure of showers can be measured and used to enhance particle identification, energy resolution and pileup rejection. In this overview we present the ideas behind HGCAL, the current status of the project, results of the beam tests and the challenges that lie ahead. Full article

We recently proposed a high-granularity calorimeter insert for the Electron-Ion Collider (EIC) that uses plastic scintillator tiles read out by SiPMs. Among its features are an ASIC-away-from-SiPM strategy for reducing cooling requirements and minimizing space use, along with employing 3D-printed frames to reduce optical crosstalk and dead areas. To evaluate these features, we built a 40-channel prototype and tested it using a 4 GeV positron beam at Jefferson Laboratory. The measured energy spectra and 3D shower shapes are well described by simulations, confirming the effectiveness of the design, construction techniques, and calibration strategy. This constitutes the first use of SiPM-on-tile technology in an EIC detector design. Full article

The upgrade of the A Toroidal LHC ApparatuS (ATLAS) hadronic Tile Calorimeter (TileCal) Low-Voltage Power Supply (LVPS) forms a part of the Phase-II Upgrade preparations undertaken by the ATLAS experiment for the data taking during the High-Luminosity Large Hadron Collider era. This paper serves to provide a detailed overview of the development of a Burn-in test station for an upgraded LVPS component known as a Brick. The production, quality assurance testing, and all associated apparatus are being jointly undertaken by the University of the Witwatersrand (Wits) and the University of Texas at Arlington (UTA). These Bricks are radiation-hard transformer-coupled buck converters that function to step-down bulk 200 VDC power to the 10 VDC required by the on-detector electronics. To ensure the high reliability of the Bricks, once installed within the TileCal, a Burn-in test station has been designed and built. The Burn-in station functions to implement a Burn-in procedure on eight Bricks simultaneously. This procedure subjects the Bricks to sub-optimal operating conditions, which function to accelerate their ageing, as well as to stimulate failure mechanisms. This results in elements of the Brick that would fail prematurely within the TileCal failing within the Burn-in station or experience performance degradation that can be detected by follow-up testing effectively screening out the non-performative sub-population. The Burn-in station is of fully custom design in both its hardware and software. The development of the test station will be explored in detail; the preliminary Burn-in procedure to be employed will be provided; the preliminary and final commissioning of the test station will be presented. The paper will culminate in the presentation and discussion of the Burn-in of a V8.4.2 Brick and the future outlook of the project. Full article

To overcome the shortcomings of the temperature sensitivity of exterior flexible facing tiles (EFFIs), a series of crosslinking carboxylic styrene-acrylate (SA) latices were prepared via the semicontinuous seed emulsion polymerization of glycidyl methacrylate (GMA), methacrylic acid (MAA), acrylic acid (AA), butyl acrylate (BA), and styrene (St), and were applied as binders to fabricate EFFTs with mineral powder. The obtained latices exhibited Bragg diffraction because of the narrow particle size distribution. Owing to the low dosage of emulsifiers and the crosslinking reaction between the epoxy group and the carboxyl group, the latex films displayed excellent water resistance, with water adsorption as low as 7.1%. The tensile test, differential scanning calorimeter (DSC) test, and dynamic mechanical analysis (DMA) indicated that at a GMA dosage of 4–6% the latex films had high mechanical strengths, which remained relatively stable in the temperature range of 10 to 40 °C. The optimal AA dosage was found in the range of 2 to 3%, at which the wet mixture exhibited good processability, conducive to forming an EFFT with a compact microstructure. Using the optimal SA latex, the obtained EFFT displayed a series of improved performances, including low water absorption, high mechanical strength, and stable self-supporting ability over a wide temperature range, exhibiting the application potential in the decoration and construction industries. Full article

The upgrade of the ATLAS hadronic tile-calorimeter (TileCal) Low-Voltage Power Supply (LVPS) falls under the high-luminosity LHC upgrade project. This article serves to provide an overview of the development of a burn-in test station for a Phase-II upgrade LVPS component known as a Brick. These Bricks are radiation hard transformer-coupled buck converters that function to step-down bulk 200 V DC power to the 10 V DC power required by the on-detector electronics. To ensure the high reliability of the Bricks, once installed within the TileCal, a burn-in test station has been designed and built. The Burn-in procedure subjects the Bricks to sub-optimal operating conditions that function to accelerate their aging as well as to stimulate failure mechanisms. This results in elements of the Brick that would fail prematurely within the TileCal failing within the burn-in station or to experience performance degradation that can be detected by followup testing effectively screening out the ’weak’ sub-population. The burn-in station is of a fully custom design in both its hardware and software. The development of the test station will be explored and the preliminary burn-in procedure to be employed will be presented. The commissioning of the burn-in station will be presented along with a summary and outlook of the project. Full article

The Tile Calorimeter (TileCal) is a sampling hadronic calorimeter covering the central region of the ATLAS experiment, with steel as the absorber and plastic scintillators as the active medium. The High-Luminosity phase of the LHC, delivering five times the LHC’s nominal instantaneous luminosity, is expected to begin in 2029. TileCal will require new electronics to meet the requirements of a 1 MHz trigger, higher ambient radiation, and to ensure better performance under high pile-up conditions. Both the on- and off-detector TileCal electronics will be replaced during the shut-down of 2026–2028. The photomultiplier tube (PMT) signals from every TileCal cell will be digitized and sent directly to the back-end electronics, where the signals are reconstructed, stored, and sent to the first level of the trigger at a rate of 40 MHz. This will provide better precision in the calorimeter signals used by the trigger system and will allow the development of more complex trigger algorithms. The modular front-end electronics feature radiation-tolerant, commercial, off-the-shelf components and a redundant design to maintain system performance in case of single points of failure. The timing, control, and communication interface with the off-detector electronics is implemented with modern Field-Programmable Gate Arrays (FPGAs) and high-speed fiber optic links running up to 9.6 Gb/s. The TileCal upgrade program has included extensive R&D and test beam studies. A Demonstrator module with reverse compatibility with respect to the existing system was inserted in ATLAS in August 2019 for testing in actual detector conditions. The ongoing developments for on- and off-detector systems, together with expected performance characteristics and results of test-beam campaigns with the electronics prototypes, will be discussed. Full article

A novel high-granularity, dual-readout calorimetric technique (ADRIANO2) is under development as part of the research program of T1604 Collaboration. (Talk Presented at the 19th International Conference on Calorimetry in Particle Physics (CALOR 2022), University of Sussex, Sussex, UK, 16–20 May 2022). The building block of such a calorimeter consists of a pair of optically isolated, small size tiles made of scintillating plastic and lead glass. The prompt Čerenkov light from the glass can be exploited to perform high resolution timing measurements, while the high granularity provides good resolution of the spatial components of the shower. Dual-readout compensation and particle flow techniques can be applied simultaneously to the scintillation and to the Čerenkov section, providing excellent energy resolution as well as PID particle identification. These characteristics make ADRIANO2 a 6-D detector, suited for High Energy as well as High Intensity experiments. A report on the status of the ADRIANO2 project, preliminary measurements of light yield, and current and future R&D plans by T1604 Collaboration are discussed. Full article

Based on the particle-flow paradigm, a new hadronic calorimeter (HCAL) with scintillating glass tiles is proposed to address major challenges from precision measurements of jets at the future lepton colliders, such as the Circular Electron Positron Collider (CEPC). Tiles of high-density scintillating glass, with a high-energy sampling fraction, can significantly improve the hadronic energy resolution in the low-energy region (typically below 10 GeV for major jet components at Higgs factories). The hadronic energy resolution of single hadrons and the effects of key parameters of scintillating glass have been evaluated in the Geant4 full simulation, followed by the physics benchmark studies on the Higgs boson with jets in the final state. R&D efforts of scintillating glass materials are ongoing within a dedicated collaboration since 2021 with the aim to achieve a high light yield, a high density, and a low cost. Measurements have been performed for the first batches of scintillating glass samples including the light yield, emission and scintillation spectra, scintillation decay times, and cosmic responses. An optical simulation model of a single scintillating glass tile has been established to provide guidance in the development of scintillating glass. Highlights of the expected detector performance and the latest scintillating glass developments are presented in this contribution. Full article

The Tile Calorimeter (TileCal) is the central hadronic calorimeter of the ATLAS experiment at the LHC. This sampling device is made of steel plates acting as absorber and scintillating tiles as active medium. The wavelength-shifting fibers collect the light from scintillators and carry it to the photomultiplier tubes (PMTs). The analogue signals from the PMTs are amplified, shaped and digitized by sampling the signal every 25 ns and stored on detector until a trigger decision is received. The TileCal front-end electronics read out the signals produced by 9852 channels, whose dynamic range covers the interval from 30 MeV to 2 TeV. Each stage of the signal propagation from scintillation light to the signal reconstruction is monitored and calibrated. During LHC Run-2, high-momentum isolated muons and isolated hadrons have been used to study and validate the electromagnetic scale and the hadronic response, respectively. The time resolution was studied with multi-jet events. Results of performance studies that address calibration, stability, energy scale, uniformity and time resolution are presented. Full article

The increase in instantaneous luminosity during the high-luminosity phase of the LHC represents a significant challenge for future detectors. A strategy to cope with high-pileup conditions is to add a fourth dimension to the measurements of the hits, by exploiting the time separation of the various proton–proton primary collisions. According to LHCb simulation studies, resolutions of about 10–20 picoseconds, at least an order of magnitude shorter than the average time span between primary interactions, would be greatly beneficial for the physics reach of the experiment. Microchannel plate (MCP) photomultipliers are compact devices capable of measuring the arrival time of charged particles with the required resolution. The technology of large-area picosecond photodetectors (LAPPDs) is under investigation to implement a timing layer that can be placed within a sampling calorimeter module with the purpose of measuring the arrival time of electromagnetic showers. LAPPD performances, using a Gen-I tile with a delay-line anode and a Gen-II with a capacitively coupled anode, have been measured thoroughly both with laser (wavelength of 405 nm and pulse width of 27.5 ps FWHM) and high-energy electron (1–5.8 GeV) beams. Time resolutions of the order of 30 ps for single photoelectrons and 15 ps for electromagnetic showers initiated by 5-GeV electrons, as measured at the shower maximum, are obtained. Full article