Search Results (14)

In this study, polymer matrix composites based on high-density polyethylene (HDPE) and recycled HDPE (HDPEr) were reinforced with zinc oxide nanoparticles (ZnO NPs). Four formulations (M1-M4) with HDPE/HDPEr/ZnO NP mass ratios of 50/50/0, 48/47/5, 45/45/10, and 43/42/15 were produced via melt injection molding. Disc-shaped samples (Ø30 ± 0.1 mm × 2 ± 0.1 mm) were evaluated in unaged and aged states (840 h at 100% humidity and 100 °C) using scanning electron microscopy, X-ray diffraction, ultraviolet–visible and Fourier-transform infrared spectroscopy, water absorption, thermal resistance, and mechanical and dielectric testing. Among all composites, M2 showed the best performance, with the highest aging resistance (estimated lifetime of 3891 h in humidity and 2361 h in heat). It also exhibited superior mechanical properties, with the highest indentation hardness, Vickers hardness, and elastic modulus before (0.042 GPa, 3.846 HV, and 0.732 GPa) and after aging under humidity (0.042 GPa, 3.932 HV, 0.706 GPa) and elevated temperature (0.085 GPa, 7.818 HV, 1.871 GPa). Although ZnO NPs slightly reduced electrical resistivity, M2 showed the most stable dielectric properties. In its unaged state, M2 had 22%, 30%, and 3% lower surface resistivity, volume resistivity, and dielectric strength, respectively, than M1 polymer. M2 was identified as the optimal formulation, combining mechanical strength, dielectric stability, and resistance to moisture and heat. Full article

Styrene-butadiene-styrene (SBS)-modified asphalt, a widely utilised binder in pavement engineering, is susceptible to ageing due to the coupling effects of thermo-oxidation, ultraviolet radiation, and humidness. Due to the limited availability of high-quality asphalt resources, recycling aged asphalt has emerged as a vital strategy for addressing resource shortages and reducing environmental pollution. This study investigated the effects of thermal-ultraviolet-humidness coupled ageing on the pavement performance of SBS-modified asphalt, with a specific focus on the hot–wet climates of Guangzhou and Chengdu. Beijing’s standard climate serves as a reference for this study. Additionally, industrial animal oil was chosen as a rejuvenator for aged SBS-modified asphalt. The mechanisms underlying hot–wet coupling ageing and regeneration of SBS-modified asphalt were analysed using Fourier Transform Infrared Spectroscopy (FTIR) and Fluorescence Microscopy (FM). The findings indicate that thermal-oxidation and humidness accelerate sulphide formation, resulting in a marked increase in sulfoxide groups and facilitating the migration of lighter components, ultimately leading to asphalt hardening. Under high-temperature and humidness conditions, the butadiene index (BI) of asphalt decreased by 5.96% in Chengdu and 15.78% in Guangzhou compared to Beijing. The sulfoxide index (SI) and aromaticity index (CI) increased by 3.74% and 3.89% in Chengdu, and by 9.39% and 8.54% in Guangzhou, respectively, confirming the exacerbating effect of humidness on ageing. During the regeneration process, industrial animal oil effectively diluted polar molecules in aged asphalt, resulting in reductions in SI by 38.88%, 36.74%, and 37.74%, and in CI by 63.77%, 62.54%, and 63.11% under ageing conditions in Beijing, Guangzhou, and Chengdu, respectively. Rejuvenation is achieved by replenishing lighter components, thereby promoting the aggregation and swelling of the degraded SBS chains. Full article

Ginsenoside Re was the major bioactive component found rich in Panax ginseng C. A. Meyer, which exerted excellent cardiovascular protection, anti-inflammatory, and anti-oxidation effects. The generation of unexpected degradation products (DPs) may influence the therapeutic effect of Re, or even bring toxic effects to patients. However, to date, only a few reports were available about the stability of Re. The present study aims to systematically investigate the degradation behaviors of Re under different stress conditions, including hydrolysis (acidic, basic, and neutral), oxidation, humidity, thermal, and photolytic (ultraviolet and visible light) conditions. A total of thirteen DPs were putatively identified, and among them, nine were discovered for the first time in our study. The results showed that Re was sensitive to exposure to acidic, basic, and oxidation conditions. It underwent a series of chemical degradation reactions, including deglycosylation, dehydration, addition, oxidation at the double bond, and isomerization under various stress conditions. Structural characterization of these DPs was carried out by UHPLC-DAD-CAD and LC-LTQ/Orbitrap. A plausible mechanism of their formation was proposed to support the structures of all DPs of Re. In silico toxicity prediction and metabolism behavior assessment were done by Derek Nexus and Meteor Nexus software. Re and DP-1 to DP-6 were predicted to possess potential skin irritation/corrosion toxicity. DP-11 and DP-12 bear the potential for carcinogenicity, mutagenicity, irritation, hepatotoxicity, and skin sensitization. The observation of these DPs updates our knowledge regarding the stability of Re, which provides valuable information for quality control and to choose suitable storage conditions. Full article

Abnormal heating will reduce the insulation performance of composite insulators or even cause insulator fracture, and the abnormal heating phenomenon is more serious under high-humidity conditions. Therefore, in this paper, the voltage withstand test of abnormal heating composite insulators caused by aging and damp sheath, decay-like core rod, and contamination were carried out under different ambient humidity. The heating and discharge of composite insulators were observed by infrared thermal imager and ultraviolet imager, and its temperature characteristics were analyzed from the aspects of heating range, heating shape, and temperature difference. In addition, in order to study the abnormal heating mechanism of composite insulators, the micro-morphology, chemical groups and dielectric properties of the silicon rubber of composite insulators with aging and damp sheath and the decay-like core rod were also measured. It is found that the temperature characteristics of the three types of abnormal heating composite insulators are different, and the temperature difference increases with the increase of humidity. The deterioration of silicone rubber and core rod material is the internal reason for the abnormal heating of composite insulators, and high-humidity conditions will exacerbate the heating phenomenon. Full article

This study explores the impact on the stability of drying and the encapsulation of a camu camu extract (CCX) using the non-thermal, high-throughput electrospraying assisted by pressurized gas (EAPG) technique. The dried and encapsulated products by the EAPG processing techniques were compared in terms of total soluble phenolic compounds, antioxidant activity, and storage stability. Whey protein concentrate (WPC) and zein (ZN) were selected as the protective excipients for encapsulation. Dried and encapsulated products were obtained in the form of microparticles, which were smaller and more spherical in the case of the encapsulates. No significant differences were observed in the total polyphenolic content (TSP), and only relatively small differences in the antioxidant capacity were measured among samples. The generated products were subjected to various storage conditions to assess their stability and the preservation of the TSP and the antioxidant properties, i.e., 0% relative humidity (RH) and 4 °C; 0% RH and 21 °C; 23% RH and 21 °C; 56% RH and 21 °C; and UV light exposure. The results indicated that ZN encapsulation notably enhanced the retention of total soluble polyphenols and the antioxidant activity compared to WPC and dried CCX, especially in the ratio of 2:1 (encapsulating polymer: dried CCX). This study demonstrates the potential of protein-based encapsulation, particularly using ZN, for stabilizing bioactive compounds against degradation mechanisms induced by humidity, temperature, or ultraviolet radiation exposure. Full article

Polymeric materials degrade as they react with environmental conditions such as temperature, light, and humidity. Electromagnetic radiation from the Sun’s ultraviolet rays weakens the mechanical properties of polymers, causing them to degrade. This study examined the phenomenon of polymer aging due to exposure to ultraviolet radiation. The study examined three specific objectives, including the key theories explaining ultraviolet (UV) radiation’s impact on polymer decomposition, the underlying testing procedures for determining the aging properties of polymeric materials, and appraising the current technical methods for enhancing the UV resistance of polymers. The study utilized a literature review methodology to understand the aging effect of electromagnetic radiation on polymers. Thus, the study concluded that using additives and UV absorbers on polymers and polymer composites can elongate the lifespan of polymers by shielding them from the aging effects of UV radiation. The findings from the study suggest that thermal conditions contribute to polymer degradation by breaking down their physical and chemical bonds. Thermal oxidative environments accelerate aging due to the presence of UV radiation and temperatures that foster a quicker degradation of plastics. Full article

Severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) has been responsible for the initiation of the global pandemic since 2020. The virus spreads through contaminated air particles, fomite, and surface-contaminated porous (i.e., paper, wood, and masks) and non-porous (i.e., plastic, stainless steel, and glass) materials. The persistence of viruses on materials depends on porosity, adsorption, evaporation, isoelectric point, and environmental conditions, such as temperature, pH, and relative humidity. Disinfection techniques are crucial for preventing viral contamination on animated and inanimate surfaces. Currently, there are few effective methodologies for preventing SARS-CoV-2 and other coronaviruses without any side effects. Before infection can occur, measures must be taken to prevent the persistence of the coronavirus on the surfaces of both porous and non-porous inanimate materials. This review focuses on coronavirus persistence in surface materials (inanimate) and control measures. Viruses are inactivated through chemical and physical methods; the chemical methods particularly include alcohol, chlorine, and peroxide, whereas temperature, pH, humidity, ultraviolet irradiation (UV), gamma radiation, X-rays, ozone, and non-thermal, plasma-generated reactive oxygen and nitrogen species (RONS) are physical methods. Full article

The accelerated aging of polyethylene terephthalate (PET) multifilament yarns containing nano or microparticles of titanium dioxide (TiO₂), silicon carbide (SiC), or fluorite (CaF₂) at a maximum percentage of 2% has been studied. For this, the yarn samples were introduced into a climatic chamber at 50 °C, 50% relative humidity, and an ultraviolet A (UVA) irradiance of 1.4 W/m². They were then removed from the chamber after periods of between 21 and 170 days of exposure. Subsequently, the variation in weight average molecular weight, number molecular weight, and polydispersity was evaluated by gel permeation chromatography (GPC), the surface appearance was evaluated using scanning electron microscopy (SEM), the thermal properties were evaluated using differential scanning calorimetry (DSC), and the mechanical properties were evaluated using dynamometry. The results showed that, at the test conditions, there was degradation in all of the exposed substrates, possibly due to the excision of the chains that make up the polymeric matrix, which resulted in the variation in the mechanical and thermal properties depending on the type and size of the particle used. This study provides insight into the evolution of the properties of PET-based nano- and microcomposites and might be helpful when selecting materials for specific applications, which is of great interest from an industrial point of view. Full article

The development of additive manufacturing methods known as “3D printing” started in the 1980s. In these methods, spatial models are created from a semi-finished product such as a powder, filament or liquid. The model is most often created in layers, which are created from the semi-finished product, which is most often subjected to thermal treatment or using light or ultraviolet rays. The technology of additive manufacturing has both advantages and disadvantages when compared to the traditionally used methods of processing thermoplastic materials, such as, for example, injection or extrusion. The most important advantages are low cost, flexibility and speed of manufacturing of elements with different spatial shapes. From the point of view of the user of the product, the most important disadvantages are the lower mechanical properties and lower resistance to environmental factors that occur during the use of the manufactured products. The purpose of this review is to present current information and a compilation of features in the field of research on the effects of the interactions of different types of environments on the mechanical properties of 3D-manufactured thermoplastic products. Changes in the structure and mechanical properties of the material under the influence of factors such as humidity, salt, temperature, UV rays, gasoline and the environment of the human body are presented. The presented article enables the effects of environmental conditions on common materials used in 3D printing technology to be collated in one place. Full article

To reduce the waste from yak hair and introduce resource recycling into the yak-related industry, an eco-friendly yak keratin-based bioplastic film was developed. We employed yak keratin (USYK) from yak hair, soy protein isolate (SPI) from soybean meal as a film-forming agent, transglutaminase (EC 2.3.2.13, TGase) as a catalytic crosslinker, and glycerol as a plasticizer for USYK-SPI bioplastic film production. The structures of the USYK-SPI bioplastic film were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-Ray diffraction (XRD). The mechanical properties, the thermal behavior, light transmittance performance, and water vapor permeability (WVP) were measured. The results revealed that the added SPI possibly acted as a reinforcement. The formation of Gln-Lys isopeptide bonds and hydrophobic interactions led to a stable crosslinking structure of USYK-SPI bioplastic film. The thermal and the mechanical behaviors of the USYK-SPI bioplastic film were improved. The enhanced dispersion and formation of co-continuous protein matrices possibly produced denser networks that limited the diffusion of water vapor and volatile compounds in the USYK-SPI bioplastic films. Moreover, the introduction of SPI prompted the relocation of hydrophobic groups on USYK molecules, which gave the USYK-SPI bioplastic film stronger surface hydrophobicity. The SPI and USYK molecules possess aromatic amino residuals (tyrosine, phenylalanine, tryptophan), which can absorb ultraviolet radiation. Thus, the USYK-SPI bioplastic films were shown to have an excellent UV barrier. The synergy effect between USYK and SPI is not only able to improve rigidity and the application performance of keratin-based composite film but can also reduce the cost of the keratin-based composite film through the low-cost of the SPI alternative which partially replaces the high-cost of keratin. The data obtained from this research can provide basic information for further research and practical applications of USYK-SPI bioplastic films. There is an increasing demand for the novel USYK-SPI bioplastic film in exploit packaging material, biomedical materials, eco-friendly wearable electronics, and humidity sensors. Full article

Older residential dwellings in New Zealand frequently suffer from poor indoor environmental quality (IEQ) due to an ageing housing stock. Recent New Zealand surveys indicated around 50% of children live in houses that do not meet acceptable standards for thermal comfort. Children in these houses frequently experience respiratory conditions caused by dampness and mould during winter. New regulatory standards requiring a fixed heating source in the main living room of rental houses can increase rents and may result in the heating source not being utilized. This study evaluates an alternative low-cost portable air filter/sterilizer (PFUV) dehumidifier device for improving IEQ within the building envelope using Ultraviolet Germicidal Irradiation (UVGI) and a polyester filter (dual-10 30/30). This paper compares the effectiveness of the PFUV dehumidifier device and a conventional heat pump in terms of measured particulate matters as well as fungal profiles using Potato Dextrose Agar (PDA) plates. The PFUV dehumidifier successfully reduced the relative humidity to within a healthy range of (44–49%) compared to not running the device (54–60%), thereby reducing the suitability of the environment for mould growth. Additionally, the PFUV device achieved a reduction in average particulate matter (PM_2.5) to within the range of 0.16 to 0.53 µg/m³ compared to the range of 1.06 to 2.42 µg/m³ before using the device. Full article

In this paper, the interrelation between temperature distribution and dry band on wet contaminated insulators is studied by theoretical analysis, numerical simulation, and a high-voltage artificial contamination experiment. The influences of the composition of the contaminant and the relative humidity of the environment on the moisture absorption of the contamination layer are studied. It is indicated that the critical relative humidity (CRH) of the soluble mixture in the contamination layer decreases with the increase of the variety of soluble substances. This can be considered as a previously neglected reason for the inconsistency between the result of an artificial contamination test and that of a natural contamination test. Furthermore, the influences of the maximum temperature, wind speed, altitude, relative humidity, and the composition of the contamination on the water evaporation rate of the contaminated layer are also studied. The formation of dry band is predicted by studying the law of water transport in the contamination layer. The influence of the location, width, drying degree, and quantity of dry bands on the insulator surface temperature are studied by numerical simulation. An infrared thermal imager and ultraviolet camera are adopted to measure the temperature distribution and the discharge phenomenon on the insulator surface separately, which verifies the above numerical simulation. The study results deepen the research on the moisture absorption characteristics, the law of temperature distribution, the formation of dry bands, and the influence of dry bands on the temperature distribution of wet contaminated insulators. Full article

Despite their excellent electrical and optical properties, Ag nanowires (NWs) suffer from oxidation when exposed to air for several days. In this study, we synthesized a Cs carbonate-incorporated overcoating layer by spin-coating and ultraviolet curing to prevent the thermal oxidation of Ag NWs. Cs incorporation increased the decomposition temperature of the overcoating layer, thus enhancing its thermal resistance. The effects of the Cs carbonate-incorporated overcoating layer on the optoelectrical properties and stability of Ag NWs were investigated in detail. The Ag NW electrode reinforced with the Cs carbonate-incorporated overcoating layer exhibited excellent thermal oxidation stability after exposure to air for 55 days at 85 °C and a relative humidity of 85%. The novel overcoating layer synthesized in this study is a promising passivation layer for Ag NWs against thermal oxidation under ambient conditions. This overcoating layer can be applied in large-area optoelectronic devices based on Ag NW electrodes. Full article

A selective, specific and stability-indicating gradient reverse phase highperformance liquid chromatographic (HPLC) method was developed for the determination of Ranitidine in presence of its impurities, forced degradation products and placebo substances such as saccharide and parabens. Ultraviolet detection was performed at 230 nm. Separate portions of the drug product and ingredients were exposed to stress conditions to induce oxidative, acidic, basic, hydrolytic, thermal and photolytic degradation. Ranitidine was found to degrade significantly at acidic, basic and oxidative stress conditions but was stable at heat and humidity. The developed method was validated as per International Conference on Harmonization (ICH) guidelines. The method was validated over this range for (i) system suitability (ii) specificity, (iii) precision, (iv) limit of detection and limit of quantification, (v) linearity, (vi) accuracy, (vii) robustness. The method was found to be precise, accurate, linear and robust. The proposed method was successfully employed for estimation of Ranitidine impurities in pharmaceutical preparations. Full article