Search Results (24)

This study successfully developed a bio-based, photocurable, anionic–nonionic dual-functional chain extender, and sulfonated cardanol-based polyethylene glycol (SCP), derived from renewable resources—cardanol and polyethylene glycol—for application in waterborne polyurethane dispersions (WPUDs). Utilizing SCP as a chain extender, WPUDs were prepared through a typical acetone process with poly(butylene adipate) (PBA), isophorone diisocyanate (IPDI), and ethylene diamine (EDA) at a constant NCO/OH ratio of 1:1. This research focused on the effects of polyethylene glycol molecular weight and SCP dosage on the particle size, stability, and film-forming properties of the WPUD. Optimal dispersion stability and film-forming performance were achieved with a polyethylene glycol molecular weight of 1500 and a PBA to SCP molar ratio of 4:1, yielding a particle size of 0.326 ± 0.010 μm and excellent storage stability over six months. The resulting WPU coatings exhibited a tensile strength of 11.4 MPa, which increased to 16.8 MPa after UV irradiation owing to the formation of a semi-interpenetrating network via the photopolymerization of cardanol’s unsaturated side chains. UV cross-linking also enhanced water resistance, reducing the water absorption rate (WAR) from 18.68% to 4.21% and the water vapor transmission rate (WVTR) from 6.59 × 10⁻⁵ g·m⁻¹·Pa⁻¹·d⁻¹ to 2.26 × 10⁻⁵ g·m⁻¹·Pa⁻¹·d⁻¹, while also improving thermal stability. These findings demonstrate that SCP offers a sustainable and effective solution for developing high-performance WPU coatings. Full article

With the increasing demand for innovative electronic products, LED transparent screens are gradually entering the public eye. Polyimide (PI) materials combine high temperature resistance and high transparency, which can be used to prepare flexible copper-clad laminate substrates. The physical and chemical properties of PI materials differ from copper, such as their thermal expansion coefficients (CTEs), surface energy, etc. These differences affect the formation and stability of the interface between copper and PI films, resulting in a short life for LED transparent screens. To enhance PI-copper interfacial adhesion, aminopropyl-terminated polydimethylsiloxane (PDMS) can be used to increase the adhesive ability. Two diamine monomers with a trifluoromethyl structure and a sulfone group structure were selected in this research. Bisphenol type A diether dianhydride is a dianhydride monomer. All three of the above monomers have non−coplanar structures and flexible structural units. The adhesion and optical properties can be improved between the interface of the synthesized PI films and copper foil. PI films containing PDMS 0, 1, 3, and 5 wt% were analyzed using UV spectroscopy. The transmittance of the PI-1/3%, PI-1/5%, PI-2/3%, and PI-2/5% films were all more than 80% at 450 nm. Meanwhile, the T_d 5% and T_{d 10%} heat loss and Tg temperatures decreased gradually with the increase in PDMS. The peel adhesion of PI-copper foil was measured using a 180° peel assay. The effect of PDMS addition on peel adhesion was analyzed. PIs-3% films had the greatest peeling intensities of 0.98 N/mm and 0.85 N/mm. Full article

A four-step synthesis process of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e., acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee. Full article

Several researchers have examined the interest in using a thermoplastic to increase thermoset polymers’ shock resistance. However, fewer studies have examined the nature of the mechanisms involved between both kinds of polymers. This was the objective of our work, which was carried out using a gradual approach. First, we describe the synthesis of a poly(ether ether ketone) oligomer (oPEEK) with hydroxyl terminations from the reaction of hydroquinone and 4,4′-difluorobenzophenone in N-methyl-2-pyrrolidone. Then, the main physicochemical properties of this oligomer were determined using different thermal analyses (i.e., differential scanning calorimetry (DSC), thermogravimetric (ATG), and thermomechanical analyses) to isolate its response alone. The chemical characterisation of this compound using conventional analytical chemistry techniques was more complex due to its insolubility. To this end, it was sulfonated, according to a well-known process, to make it soluble and enable nuclear magnetic resonance (NMR) and size exclusion chromatography (SEC) experiments. Additional information about the structural and chemical characteristics of the oligomer and its average molecular weight could thus be obtained. The synthesis of an oligoPEEK with α,ω-hydroxyl end-groups and a molecular weight of around 5070 g/mol was thus confirmed by NMR. This value was in accordance with that determined by SEC analysis. Next, the reaction of oPEEK with an epoxy prepolymer was demonstrated using DSC and dynamic rheometry. To this end, uncured mixtures of epoxy prepolymer (DGEBA) with different proportions of oPEEK (3, 5, 10 and 25%) were prepared and characterised by both techniques. Ultimately, the epoxy-oPEEK mixture was cured with isophorone diamine. Finally, topological analyses were performed by atomic force microscopy (AFM) in tapping mode to investigate the interface quality between the epoxy matrix and the oPEEK particles indirectly. No defects, such as decohesion areas, microvoids, or cracks, were observed between both systems. Full article

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF₃ and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400 °C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis(trifluoromethyl)benzidine (TFMB) and bis(4-aminophenyl)sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis(4-aminophenyl)hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively. Full article

Most commercially available polymers are synthesized from compounds derived from petroleum, a finite resource. Because of this, there is a growing interest in the synthesis of new polymeric materials using renewable monomers. Following this concept, this work reports on the use of muconic acid as a renewable source for the development of new polyamides that can be used as proton-exchange membranes. Muconic acid was used as a comonomer in polycondensation reactions with 4,4′-(hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline, 2,5-diaminobencensulfonic acid, and 4,4′-diamino-2,2′-stilbenedisulfonic acid as comonomers in the synthesis of two new series of partially renewable aromatic–aliphatic polyamides, in which the degree of sulfonation was varied. Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (¹H, ¹³C, and ¹⁹F-NMR) techniques were used to confirm the chemical structures of the new polyamides. It was also observed that the degree of sulfonation was proportional to the molar ratio of the diamines in the feed. Subsequently, membranes were prepared by casting, and a complete characterization was conducted to determine their decomposition temperature (T_d), glass transition temperature (T_g), density (ρ), and other physical properties. In addition, water uptake (W_u), ion-exchange capacity (IEC), and proton conductivity (σ_p) were determined for these membranes. Electrochemical impedance spectroscopy (EIS) was used to determine the conductivity of the membranes. MUFASA34 exhibited a σ_p value equal to 9.89 mS·cm⁻¹, being the highest conductivity of all the membranes synthesized in this study. Full article

Astragalus species are traditionally used for diabetes, ulcers, leukemia, wounds, stomachaches, sore throats, abdominal pain, and toothaches. Although the preventive effects of Astragalus species against diseases are known, there is no record of the therapeutic effects of Astragalus alopecurus. In this study, we aimed to evaluate the in vitro antiglaucoma, antidiabetic, anti-Alzheimer’s disease, and antioxidant activities of the methanolic (MEAA) and water (WEAA) extracts of the aerial part of A. alopecurus. Additionally, its phenolic compound profiles were analyzed by liquid chromatography–tandem mass spectrometry (LC–MS/MS). MEAA and WEAA were evaluated for their inhibition ability on α-glycosidase, α-amylase, acetylcholinesterase (AChE), and human carbonic anhydrase II (hCA II) enzymes. The phenolic compounds of MEAA were analyzed by LC-MS/MS. Furthermore, total phenolic and flavonoid contents were determined. In this context, the antioxidant activity was evaluated by 1,1-diphenyl-2-picrylhydrazyl (DPPH), 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS), N,N-dimethyl-p-phenylene diamine (DMPD), ferric reducing antioxidant power (FRAP), cupric ions (Cu²⁺) reducing antioxidant capacity (CUPRAC), ferric ions (Fe³⁺) reducing, and ferrous ions (Fe²⁺) chelating methods. MEAA and WEAA had IC₅₀ values of 9.07 and 2.24 μg/mL for α-glycosidase, 693.15 and 346.58 μg/mL for α-amylase, 1.99 and 2.45 μg/mL for AChE, and 147.7 and 171.7 μg/mL for hCA II. While the total phenolic amounts in MEAA and WEAA were 16.00 and 18.50 μg gallic acid equivalent (GAE)/mg extract, the total flavonoid contents in both extracts were calculated as 66.23 and 33.115 μg quercetin equivalent (QE)/mg, respectively. MEAA and WEAA showed, respectively, variable activities on DPPH radical scavenging (IC₅₀: 99.02 and 115.53 μg/mL), ABTS radical scavenging (IC₅₀: 32.21 and 30.22 µg/mL), DMPD radical scavenging (IC₅₀: 231.05 and 65.22 μg/mL), and Fe²⁺ chelating (IC₅₀: 46.21 and 33.01 μg/mL). MEAA and WEAA reducing abilities were, respectively, Fe³⁺ reducing (λ₇₀₀: 0.308 and 0.284), FRAP (λ₅₉₃: 0.284 and 0.284), and CUPRAC (λ₄₅₀: 0.163 and 0.137). A total of 35 phenolics were scanned, and 10 phenolic compounds were determined by LC-MS/MS analysis. LC-MS/MS revealed that MEAA mainly contained isorhamnetin, fumaric acid, and rosmarinic acid derivatives. This is the first report indicating that MEAA and WEAA have α-glycosidase, α-amylase, AChE, hCA II inhibition abilities, and antioxidant activities. These results demonstrate the potential of Astragalus species through antioxidant properties and enzyme inhibitor ability traditionally used in medicine. This work provides the foundation for further research into the establishment of novel therapeutics for diabetes, glaucoma, and Alzheimer’s disease. Full article

Research into bio-based epoxy resins has intensified in recent decades. Here, it is of great importance to use raw materials whose use does not compete with food production. In addition, the performance of the newly developed materials should be comparable to that of conventional products. Possible starting materials are lignin degradation products, such as vanillin and syringaldehyde, for which new synthesis routes to the desired products must be found and their properties determined. In this article, the first synthesis of two amine hardeners, starting with vanillin and syringaldehyde, using the Smiles rearrangement reaction is reported. The amine hardeners were mixed with bisphenol A diglycidyl ether, and the curing was compared to isophorone diamine, 4-4′-diaminodiphenyl sulfone, and 4-Aminonbenzylamine by means of differential scanning calorimetry. It was found that the two amines prepared are cold-curing. As TG-MS studies showed, the thermal stability of at least one of the polymers prepared with the potentially bio-based amines is comparable to that of the polymer prepared with isophorone diamine, and similar degradation products are formed during pyrolysis. Full article

The formation of polymeric micro-patterns on various substrates via a photolithography procedure has been widely used in semiconductor fabrication. Standard polymer patterns are usually fabricated via photosensitive polymer varnishes, in which large amounts of potentially harmful solvents with weight ratios over 50 wt% have to be removed. In the current work, a novel pattern-formation methodology via solvent-free electrospun photosensitive polymeric fibrous membranes (NFMs) instead of the conventional photosensitive solutions as the starting photoresists was proposed and practiced. For this purpose, a series of preimidized negative auto-photosensitive polyimide (PSPI) resins were first prepared via the two-step chemical imidization procedure from the copolymerization reactions of 3,3′,4,4′-benzophenonetetracarboxylic- dianhydride (BTDA) and two ortho-methyl-substituted aromatic diamines, including 3,3′,5,5′-tetramethyl-4,4′-diaminodiphenylmethane (TMMDA) and 3,7-diamino-2,8-dimethyl- dibenzothiophene sulfone (TSN). The derived homopolymer PI-1 (BTDA-TMMDA) and the copolymers, including SPI-2~SPI-6, with the molar ratio of 5~25% for TSN in the diamine units, showed good solubility in polar solvents. Then, a series of PSPI NFMs were fabricated via standard electrospinning procedure with the developed PSPI solutions in N,N-dimethylacetamide (DMAc) with a solid content of 25 wt% as the starting materials. The derived PSPI NFMs showed good thermal stability with 5% weight loss temperatures higher than 500 °C in nitrogen. Meanwhile, the derived PSPIs showed good photosensitivity to the ultraviolet (UV) emitting wavelengths of i-line (365 nm), g-line (405 nm) and h-line (436 nm) of the high-pressure mercury lamps in both forms of transparent films and opaque NFMs. Fine micro-patterns with a line width of around 100 μm were directly obtained from the representative SPI-4 NFM via standard photolithography procedure. Full article

Poly(amic acid) (PAA) was synthesized from dianhydride 4,4-(4,4-isopropylidenediphenoxy)bis(phthalic anhydride) and diamine bis [4-(3-aminophenoxy) phenyl] sulfone. Colorless and transparent polyimide (CPI) hybrid films were synthesized through thermal imidization after dispersing nanofillers using an intercalation method in a PAA solution. C16-GS and C16-MMT, in which hexadecylamine (C16) was substituted on graphene sheet (GS) and montmorillonite (MMT), respectively, were used as nanofillers to reinforce the CPI hybrid films. These two nanofillers were admixed in varying loadings of 0.25 to 1.00 wt%, and the morphology, thermal properties, and optical transparency of the hybrid films were investigated and compared. The results suggest that the thermal properties of the CPI hybrid films can be improved by adding only a small amount of nanofiller. Transmission electron microscopy results of the CPI hybrid film containing two types of fillers suggested that the fillers were well dispersed in the nano-size in the matrix polymer; however, some of the fillers were observed as agglomerated particles above the critical concentration of 0.50 wt%. Full article

For improving the hydrolytic stability of sulfonated polyimides consisting of five membered anhydrides, novel sulfonated polyimides (NSPIs) were prepared via polymerization of 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), with a novel diamine monomer with a pendant sulfonic acid group and 4,4-oxydianiline. Water uptake of this NSPI with an excellent film-forming ability was almost equal to that of Nafion^® 117, while their ion exchange capacity (IEC) was 22% higher than Nafion^® 117. The loss in weight decreased by 53% and loss in IEC decreased by 66% compared to that of Nafion^® 117; both were used to quantitatively measure hydrolytic stability, and radical oxidative stability also increased by 75% when compared with Nafion^® 117. Mechanically, this NSPI was superior, and its proton conductivity was higher than Nafion^® 117 at elevated temperatures. All these improvements were due to the introduction of this pendant group. Taken together, we herein report a promising renewable energy source based on SPIs capable of displaying proton conductivity and enhanced hydrophilicity. Full article

4,4′-(4,4′-isopropylidenediphenoxy)bis(phthalic anhydride) (BPADA) as a dianhydride and bis(3-aminophenyl) sulfone (APS) and bis(3-amino-4-hydroxyphenyl) sulfone (APS-OH) as diamines were used to synthesize two types of poly(amic acid) (PAA). Varying amounts (0–5.0 wt%) of water-soluble poly(vinyl alcohol) (PVA) were mixed with PAA, and the resulting blend was heat-treated at different stages to obtain the colorless and transparent polyimide (CPI) blend films. The synthesized blended film completely removed water-soluble PVA in water. The possibility as a porous membrane according to the pore size varied according to the amount of PVA was investigated. The dispersibility and compatibility of CPI containing APS-OH monomer were higher than those of the APS monomer. This could be attributed to the hydrogen-bonding interactions between the CPI main chains and PVA. Scanning electron microscopy was conducted to characterize the material. The results revealed that the pore size of the CPI blend film increased as the PVA concentration increased. It was confirmed that uniform pores of μm-size were observed in CPI. The thermal stabilities, morphologies, optical properties, and solubilities of two CPIs obtained using APS and APS-OH monomers were investigated and their properties were compared with each other. Full article

The future availability of synthetic polymers is compromised due to the continuous depletion of fossil reserves; thus, the quest for sustainable and eco-friendly specialty polymers is of the utmost importance to ensure our lifestyle. In this regard, this study reports on the use of oleic acid as a renewable source to develop new ionomers intended for proton exchange membranes. Firstly, the cross-metathesis of oleic acid was conducted to yield a renewable and unsaturated long-chain aliphatic dicarboxylic acid, which was further subjected to polycondensation reactions with two aromatic diamines, 4,4′-(hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline and 4,4′-diamino-2,2′-stilbenedisulfonic acid, as comonomers for the synthesis of a series of partially renewable aromatic-aliphatic polyamides with an increasing degree of sulfonation (DS). The polymer chemical structures were confirmed by Fourier transform infrared (FTIR) and nuclear magnetic resonance (¹H, ¹³C, and ¹⁹F NMR) spectroscopy, which revealed that the DS was effectively tailored by adjusting the feed molar ratio of the diamines. Next, we performed a study involving the ion exchange capacity, the water uptake, and the proton conductivity in membranes prepared from these partially renewable long-chain polyamides, along with a thorough characterization of the thermomechanical and physical properties. The highest value of the proton conductivity determined by electrochemical impedance spectroscopy (EIS) was found to be 1.55 mS cm⁻¹ at 30 °C after activation of the polymer membrane. Full article

Transparent polyimides (PI) films with outstanding overall performance are attractive for next generation optoelectronic and microelectronic applications. Semi-alicyclic PIs derived from alicyclic dianhydrides and aromatic diamines have proved effective to prepare transparent PIs with high transmittance. To optimize the combined properties of semi-alicyclic PIs, incorporating bulky trifluoromethyl groups into the backbones is regarded as a powerful tool. However, the lack of fundamental understanding of structure–property relationships of fluorinated semi-alicyclic PIs constrains the design and engineering of advanced films for such challenging applications. Herein, a series of semi-alicyclic PIs derived from alicyclic dianhydrides and trifluoromethyl-containing aromatic diamines was synthesized by solution polycondensation at high temperature. The effects of alicyclic structures and bulky trifluoromethyl groups on thermal, dielectric and optical properties of PIs were investigated systematically. These PI films had excellent solubility, low water absorption and good mechanical property. They showed high heat resistance with T_g in the range of 294–390 °C. It is noted that tensile strength and thermal stability were greatly affected by the rigid linkages and alicyclic moieties, respectively. These films exhibited obviously low refractive indices and significantly reduced dielectric constants from 2.61 to 2.76, together with low optical birefringence and dielectric anisotropy. Highly transparent films exhibited cutoff wavelength even as low as 298 nm and transmittance at 500 nm over 85%, displaying almost colorless appearance with yellowness index (b*) below 4.2. The remarkable optical improvement should be mainly ascribed to both weak electron-accepting alicyclic units and bulky electron-withdrawing trifluoromethyl or sulfone groups. The present work provides an effective strategy to design molecular structures of optically transparent PIs for a trade-off between solution-processability, low water uptake, good toughness, high heat resistance, low dielectric constant and excellent optical transparency. Full article

Hydrolytic stability and oxidative stability are the core properties of sulfonated polynaphthylimides (SPIs) as proton exchange membranes. The chemical structure of SPIs directly influences the performance. Herein, three different series of branched SPIs were designed and prepared using 1,3,5-tris (2-trifluoromethyl-4-aminophenoxy) benzene as a trifunctional monomer and three non-sulfonated diamine monomers, such as 4,4′-oxydianiline (ODA), 2,2-bis[4-(4-aminophenoxy)phenyl]hexafluoropropane (6FODA), and 4,4′-(9-fluorenylidene)dianiline (BFDA). The effect of the chemical structure and degree of branching on SPIs properties is discussed. The results showed that by controlling the chemical structure and degree of branching, the chemical stability of SPIs changed significantly. SPI-6FODA with two ether linkages and a hydrophobic CF₃ group has higher hydrolytic stability than SPI-ODA with only one ether linkage. In addition, with the increase of the introduced B₃ monomer, the oxidation stability of SPI-6FODA has been greatly improved. We successfully synthesized SPIs with a high hydrolytic stability and oxidative stability. Full article