Search Results (56)

This paper explores the potential of phase change materials (PCM) for dynamically tuning the frequency response of a dumbbell u-slot defected ground structure (DGS)-based band stop filter. The DGSs are designed using co-planar waveguide (CPW) line structure on top of a barium strontium titanate (Ba_0.6Sr_0.4TiO₃) (BST) thin film. BST film is used as the high-dielectric material for the planar DGS. Lower insertion loss of less than −2 dB below the lower cutoff frequency, and enhanced band-rejection with notch depth of −39.64 dB at 27.75 GHz is achieved by cascading two-unit cells, compared to −12.26 dB rejection with a single-unit cell using BST thin film only. Further tunability is achieved by using a germanium telluride (GeTe) PCM layer. The electrical properties of PCM can be reversibly altered by transitioning between amorphous and crystalline phases. We demonstrate that incorporating a PCM layer into a DGS device allows for significant tuning of the resonance frequency: a shift in resonance frequency from 30.75 GHz to 33 GHz with a frequency shift of 2.25 GHz is achieved, i.e., 7.32% tuning is shown with a single DGS cell. Furthermore, by cascading two DGS cells with PCM, an even wider tuning range is achievable: a shift in resonance frequency from 27 GHz to 30.25 GHz with a frequency shift of 3.25 GHz is achieved, i.e., 12.04% tuning is shown by cascading two DGS cells. The results are validated through simulations and measurements, showcasing excellent agreement. Full article

The demand for reconfigurable devices for emerging RF and microwave applications has been growing in recent years, with additive manufacturing and photonic thermal treatment presenting new possibilities to supplement conventional fabrication processes to meet this demand. In this paper, we present the realization and analysis of barium–strontium–titanate-(Ba_0.5Sr_0.5TiO₃)-based ferroelectric variable capacitors (varactors), which are additively deposited on top of conventionally fabricated interdigitated capacitors and enhanced by photonic thermal processing. The ferroelectric solution with suspended BST nanoparticles is deposited on the device using an ambient spray pyrolysis method and is sintered at low temperatures using photonic thermal processing by leveraging the high surface-to-volume ratio of the BST nanoparticles. The deposited film is qualitatively characterized using SEM imaging and XRD measurements, while the varactor devices are quantitatively characterized by using high-frequency RF measurements from 300 MHz to 10 GHz under an applied DC bias voltage ranging from 0 V to 50 V. We observe a maximum tunability of 60.6% at 1 GHz under an applied electric field of 25 kV/mm (25 V/μm). These results show promise for the implementation of photonic thermal processing and additive manufacturing as a means to integrate reconfigurable ferroelectric varactors in flexible electronics or tightly packaged on-chip applications, where a limited thermal budget hinders the conventional thermal processing. Full article

Amidst the swift expansion of the electric vehicle industry, the imperative for alternative battery technologies that balance economic feasibility with sustainability has reached unprecedented importance. Herein, we utilized Perovskite-based oxide compounds barium titanate (BaTiO₃) and strontium titanate (SrTiO₃) nanoparticles as anode materials for lithium-ion batteries from straightforward and standard carbonate-based electrolyte with 10% fluoroethylene carbonate (FEC) additive [1M LiPF₆ (1:1 EC: DEC) + 10% FEC]. SrTiO₃ and BaTiO₃ electrodes can deliver a high specific capacity of 80 mA h g⁻¹ at a safe and low average working potential of ≈0.6 V vs. Li/Li⁺ with excellent high-rate performance with specific capacity of ~90 mA h g⁻¹ at low current density of 20 mA g⁻¹ and specific capacity of ~80 mA h g⁻¹ for over 500 cycles at high current density of 100 mA g⁻¹. Our findings pave the way for the direct utilization of perovskite-type materials as anode materials in Li-ion batteries due to their promising potential for Li⁺ ion storage. This investigation addresses the escalating market demands in a sustainable manner and opens avenues for the investigation of diverse perovskite oxides as advanced anodes for next-generation metal-ion batteries. Full article

Thin films of strontium titanate, which reveal high structure quality and tunable properties prospective for microwave applications at room temperature, were grown on a semi-insulating silicon carbide substrate using magnetron sputtering for the first time. The films’ growth mechanisms were studied using medium-energy ion scattering, and the films’ structures were investigated using X-ray diffraction. The electrical characteristics of planar capacitors based on strontium titanate films were measured at a frequency of 2 GHz using a high-precision resonance technique. It is shown that the tendency to improve the crystalline structure of strontium titanate film with an increase in the substrate temperature is most pronounced for films deposited at elevated working gas pressure under low supersaturation conditions. Planar capacitors formed on the basis of oriented SrTiO₃ films on silicon carbide showed tunability n = 36%, with a loss tangent of 0.008–0.009 at a level of slow relaxation of capacitance, which is significantly lower than the data published currently regarding planar tunable ferroelectric elements. This is the first successful attempt to realize a planar SrTiO₃ capacitor on a silicon carbide substrate, which exhibits a commutation quality factor more than 2500 at microwaves. Full article

The remarkable stability, suitable thermomechanical characteristics, and acceptable electrical properties of donor-doped strontium titanates make them attractive materials for fuel electrodes, interconnects, and supports of solid oxide fuel and electrolysis cells (SOFC/SOEC). The present study addresses the impact of processing and thermochemical treatment conditions on the electrical conductivity of SrTiO₃-derived ceramics with moderate acceptor-type substitution in a strontium sublattice. A-site-deficient Sr_0.85La_0.10TiO_3−δ and cation-stoichiometric Sr_0.85Pr_0.15TiO_3+δ ceramics with varying microstructures and levels of reduction have been prepared and characterized by XRD, SEM, TGA, and electrical conductivity measurements under reducing conditions. The analysis of the collected data suggested that the reduction process of dense donor-doped SrTiO₃ ceramics is limited by sluggish oxygen diffusion in the crystal lattice even at temperatures as high as 1300 °C. A higher degree of reduction and higher electrical conductivity can be obtained for porous structures under similar thermochemical treatment conditions. Metallic-like conductivity in dense reduced Sr_0.85La_0.10TiO_3−δ corresponds to the state quenched from the processing temperature and is proportional to the concentration of Ti³⁺ in the lattice. Due to poor oxygen diffusivity in the bulk, dense Sr_0.85La_0.10TiO_3−δ ceramics remain redox inactive and maintain a high level of conductivity under reducing conditions at temperatures below 1000 °C. While the behavior and properties of dense reduced Sr_0.85Pr_0.15TiO_3+δ ceramics with a large grain size (10–40 µm) were found to be similar, decreasing grain size down to 1–3 µm results in an increasing role of resistive grain boundaries which, regardless of the degree of reduction, determine the semiconducting behavior and lower total electrical conductivity of fine-grained Sr_0.85Pr_0.15TiO_3+δ ceramics. Oxidized porous Sr_0.85Pr_0.15TiO_3+δ ceramics exhibit faster kinetics of reduction compared to the Sr_0.85La_0.10TiO_3−δ counterpart at temperatures below 1000 °C, whereas equilibration kinetics of porous Sr_0.85La_0.10TiO_3−δ structures can be facilitated by reductive pre-treatments at elevated temperatures. Full article

In the present paper, composite thin films of barium strontium titanate (Ba_xSr_1−xTiO₃) with an acceptor modifier (magnesium oxide—MgO) were deposited on metal substrates (stainless steel type) using the sol–gel method. The composite thin films feature Ba_xSr_1−xTiO₃ ferroelectric solid solution as the matrix and MgO linear dielectric as the reinforcement, with MgO concentrations ranging from 1 to 5 mol%. Following thermal treatment at 650 °C, the films were analyzed for their impedance response. Experimental impedance spectra were modeled using the Kohlrausch–Williams–Watts function, revealing stretching parameters (β) in the range of approximately 0.78 to 0.89 and 0.56 to 0.90 for impedance and electric modulus formalisms, respectively. Notably, films modified with 3 mol% MgO exhibited the least stretched relaxation function. Employing the electric equivalent circuit method for data analysis, the “circle fit” analysis demonstrated an increase in capacitance from 2.97 × 10⁻¹² F to 5.78 × 10⁻¹⁰ F with the incorporation of 3 mol% MgO into BST-based thin films. Further analysis based on Voigt, Maxwell, and ladder circuits revealed trends in resistance and capacitance components with varying MgO contents, suggesting non-Debye-type relaxation phenomena across all tested samples. Full article

SnO₂-based gas sensors have been widely synthesized and used for the detection of various hazardous gases. However, the use of doped SnO₂ in sensing applications has recently attracted increased interest due to the formation of a synergistic effect between the dopant and the host. Moreover, in the case of a surface acoustic wave (SAW) sensor, the piezoelectric material used in the fabrication of the sensor plays a crucial role in defining the response of the SAW sensor. As a ferroelectric material, barium strontium titanate (Ba_0.6Sr_0.4TiO₃) has recently been studied due to its intriguing dielectric and electromechanical properties. Its high acoustic velocity and coupling coefficient make it a promising candidate for the development of acoustic devices; however, its use as a piezoelectric material in SAW sensors is still in its infancy. In this paper, we present the design, fabrication and validation of an indium doped SnO₂-based SAW gas sensor on Ba_0.6Sr_0.4TiO₃ thin film for room temperature (RT) applications. Pulsed laser deposition was used to deposit thin films of Ba_0.6Sr_0.4TiO₃ and indium-doped SnO₂. Different characterization techniques were employed to analyze the morphology and crystallization of the films. The performance of the fabricated sensor was validated by exposing it to different concentrations of ethanol and then analyzing the recorded frequency shift. The sensor exhibited fast response (39 s) and recovery (50 s) times with a sensitivity of 9.9 MHz/Δ. Moreover, the sensor had good linear response and reproducibility. The fabricated indium-doped SnO₂-based SAW gas sensor could be suitable for practical room temperature applications. Full article

Engineering of oxygen vacancies (Vo) in nanomaterials allows diligent control of their physicochemical properties. SrTiO₃ possesses the typical ABO₃ structure and has attracted considerable attention among the titanates due to its chemical stability and its high conduction band energy. This has resulted in its extensive use in photocatalytic energy-related processes, among others. Herein, we introduce the use of Flame Spray Pyrolysis (FSP); an industrial and scalable process to produce Vo-rich SrTiO₃ perovskites. We present two types of Anoxic Flame Spray Pyrolysis (A-FSP) technologies using CH₄ gas as a reducing source: Radial A-FSP (RA-FSP); and Axial A-FSP (AA-FSP). These are used for the control engineering of oxygen vacancies in the SrTiO_3-x nanolattice. Based on X-ray photoelectron spectroscopy, Raman and thermogravimetry-differential thermal analysis, we discuss the role and the amount of the Vos in the so-produced nano-SrTiO_3-x, correlating the properties of the nanolattice and energy-band structure of the SrTiO_3-x. The present work further corroborates the versatility of FSP as a synthetic process and the potential future application of this process to engineer photocatalysts with oxygen vacancies in quantities that can be measured in kilograms. Full article

This article presents a wide-angle-scanning leaky-wave antenna (LWA) based on a composite right/left-handed (CRLH) transmission line. In contrast to traditional semiconductor elements, thin-film ferroelectric capacitors were implemented in the CRLH unit cells to enable electric beam scanning. The proposed CRLH LWA has a single-layer design without metalized vias and is compatible with PCB and thin-film technologies. To fabricate the CRLH LWA prototype, dielectric material substrates and thin-film ferroelectric capacitors were manufactured, and their characteristics were investigated. Double-sided metalized fluoroplast-4 reinforced with fiberglass with a permittivity of 2.5 was used as a substrate for CRLH LWA prototyping. A solid solution of barium strontium titanate (Ba${}_x$Sr${}_{1-x}$TiO${}_3$) with a composition of $x=0.3$ was used as a ferroelectric material in electrically tunable capacitors. The characteristics of the manufactured ferroelectric thin-film capacitors were measured at a frequency of 1 GHz using the resonance method. The capacitors have a tunability of about two and a quality factor of about 50. The antenna prototype consists of ten units with a total length of 1.25 wavelengths at the operating frequency of close to 2.4 GHz. The experimental results demonstrate that the main beam can be shifted within the range of −40 to 16 degrees and has a gain of up to 3.2 dB. The simple design, low cost, and excellent wide-angle scanning make the proposed CRLH LWA viable in wireless communication systems. Full article

While dental poly methyl methacrylate(PMMA) possesses distinctive qualities such as ease of fabrication, cost-effectiveness, and favorable physical and mechanical properties, these attributes alone are inadequate to impart the necessary impact strength and hardness. Consequently, pure PMMA is less suitable for dental applications. This research focused on the incorporation of Strontium titanate (SrTiO₃-STO) and hybrid filler STO/Manganese oxide (MnO₂) to improve impact resistance and hardness. The potential of STO in reinforcing PMMA is poorly investigated, while hybrid filler STO/MnO₂ has not been presented yet. Differential scanning calorimetry is conducted in order to investigate the agglomeration influence on the PMMA glass transition temperature (T_g), as well as the leaching of residual monomer and volatile additives that could pose a threat to human health. It has been determined that agglomeration with 1 wt% loading had no influence on T_g, while the first scan revealed differences in evaporation of small molecules, in favor of composite PMMA-STO/MnO₂, which showed the trapping potential of volatiles. Investigations of mechanical properties have revealed the significant influence of hybrid STO/MnO₂ filler on microhardness and total absorbed impact energy, which were increased by 89.9% and 145.4%, respectively. Results presented in this study revealed the reinforcing potential of hybrid nanoparticles that could find application in other polymers as well. Full article

Solid oxide fuel cells are characterized by a high efficiency for converting chemical energy into electricity and fuel flexibility. This research work focuses on developing durable and efficient anodes for solid oxide fuel cells (SOFCs) based on exsolving nickel from the perovskite structure. A-site-deficient La- and Ni-doped strontium titanates (La_0.2Sr_0.7Ti_0.95Ni_0.05O_3−δ, LSTN) were synthesized using four different techniques and mixed with Ce_0.8Gd_0.2O_2−δ (GDC) to form the SOFC anode. The synthesis routes of interest for comparison included solid-state, sol-gel, hydrothermal, and co-precipitation methods. LSTN powders were characterized via XRD, SEM, TPR, BET and XPS. In situ XRD during reduction was measured and the reduced powders were analyzed using TEM. The impact of synthesis route on SOFC performance was investigated. All samples were highly durable when kept at 0.5 V for 48 h at 800 °C with H₂ fuel. Interestingly, the best performance was observed for the cell with the LSTN anode prepared via co-precipitation, while the conventional solid-state synthesis method only achieved the second-best results. Full article

Thin film technology shows great promise in fabricating electronic devices such as gas sensors. Here, we report the fabrication of surface acoustic wave (SAW) sensors based on thin films of (1 − x) Ba(Ti_0.8Zr_0.2)O_3−x(Ba_0.7Ca_0.3)TiO₃ (BCTZ50, x = 50) and Polyethylenimine (PEI). The layers were deposited by two laser-based techniques, namely pulsed laser deposition (PLD) for the lead-free material and matrix assisted pulsed laser evaporation (MAPLE) for the sensitive polymer. In order to assay the impact of the thickness, the number of laser pulses was varied, leading to thicknesses between 50 and 350 nm. The influence of BCTZ film’s crystallographic features on the characteristics and performance of the SAW device was studied by employing substrates with different crystal structures, more precisely cubic Strontium Titanate (SrTiO₃) and orthorhombic Gadolinium Scandium Oxide (GdScO₃). The SAW sensors were further integrated into a testing system to evaluate the response of the BCTZ thin films with PEI, and then subjected to tests for N₂, CO₂ and O₂ gases. The influence of the MAPLE’s deposited PEI layer on the overall performance was demonstrated. For the SAW sensors based on BCTZ/GdScO₃ thin films with a PEI polymer, a maximum frequency shift of 39.5 kHz has been obtained for CO₂; eight times higher compared to the sensor without the polymeric layer. Full article

Thin films of strontium titanate, which have nonlinear properties that are promising for microwave applications, were grown on a polycrystalline aluminum oxide substrate using magnetron sputtering and high-temperature annealing. It was shown that the improvement of the film structure with an increase in the deposition temperature was clearly correlated with both an increase in nonlinearity and an improvement in the loss level. A capacitor based on an SrTiO₃ film deposited at a deposition temperature of 900 °C and subjected to annealing demonstrated a tunability of 46% with a loss tangent of 0.009–0.014 at a frequency of 2 GHz. This was the first successful attempt to form a planar SrTiO₃ capacitor on an alumina substrate, which exhibited a commutation quality factor of above 3000 in the microwave range. Full article

Epitaxial lithium ferrite (LiFe₅O₈) films with different thicknesses were successfully fabricated on strontium titanate (SrTiO₃) (001) substrates using the magnetron sputtering deposition technique. The microstructural and magnetic properties of the films were characterized by an advanced transmission electron microscope and a magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. In addition to misfit dislocations, orientation domains form in thinner films and twin boundaries appear in thicker films, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement showed that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing antiferromagnetic twin boundaries. Our results provide a way of tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness. Full article

Perovskite-type Sr(Ti,V)O_3-δ ceramics are promising anode materials for natural gas- and biogas-fueled solid oxide fuel cells, but the instability of these phases under oxidizing conditions complicates their practical application. The present work explores approaches to the fabrication of strontium titanate-vanadate electrodes from oxidized precursors. Porous ceramics with the nominal composition SrTi_1−yV_yO_z (y = 0.1–0.3) were prepared in air via a solid state reaction route. Thermal processing at temperatures not exceeding 1100 °C yielded composite ceramics comprising perovskite-type SrTiO₃, pyrovanadate Sr₂V₂O₇ and orthovanadate Sr₃(VO₄)₂ phases, while increasing firing temperatures to 1250–1440 °C enabled the formation of SrTi_1−yV_yO₃ perovskites. Vanadium was found to substitute into the titanium sublattice predominantly as V⁴⁺, even under oxidizing conditions at elevated temperatures. Both perovskite and composite oxidized ceramics exhibit moderate thermal expansion coefficients in air, 11.1–12.1 ppm/K at 30–1000 °C, and insignificant dimensional changes induced by reduction in a 10%H₂-N₂ atmosphere. The electrical conductivity of reduced perovskite samples remains comparatively low, ~10⁻¹ S/cm at 900 °C, whereas the transformation of oxidized vanadate phases into high-conducting SrVO_3−δ perovskites upon reduction results in enhancement in conductivity, which reaches ~3 S/cm at 900 °C in porous composite ceramics with nominal composition SrTi_0.7V_0.3O_z. The electrical performance of the composite is expected to be further improved by optimization of the processing route and microstructure to facilitate the reduction of the oxidized precursor and attain better percolation of the SrVO₃ phase. Full article