Search Results (12)

Titanium alloy is a crucial structural material in the modern aerospace field due to its strong corrosion resistance and strength, low density, and reduced sensitivity to vibration load and impact load, as well as its ability to resist expansion in the case of cracks. However, during high-speed cutting of titanium alloy, it is prone to periodic saw-tooth chip formation, which can cause high-frequency fluctuations in the cutting force, aggravate the vibration of the machine tool system, and ultimately reduce the tool’s service life and the workpiece’s surface quality. In this study, we investigated the influence of the material constitutive law in modeling the Ti-6AL-4V saw-tooth chip formation and proposed a joint material constitutive law JC-TANH which was developed based on the Johnson–Cook constitutive law and the TANH constitutive law. It has two advantages of the two models (JC law and TANH law), which means that it can describe the dynamic properties accurately, the same as the JC model, not only under low strain but also under high strain. The most important thing is that it does not need to fit the JC curve at the early stage of strain changes. Additionally, we established a developed cutting model, which integrates the new material constitutive, and the improved SPH method to predict chip morphology, cutting and thrust forces which are collected by the force sensor; we also compared the data with experimental results. Experimental results show that this developed cutting model can better explain the shear localized saw-tooth chip formation and correctly estimate its morphology as well as the cutting forces. Full article

Magnesium alloys have broad applications, including medical implants and the aerospace sector owing to their great density and high strength-to-weight ratio. Dry cutting is a frequent technique for machining this material. However, it always leads to an excessive rise in temperature due to the absence of cooling at the cutting zone, which affects the machined surface integrity and chip morphology. In this study, chip morphology and surface integrity of the AZ31 magnesium alloy were investigated in the turning process using an internal cooling method called submerged convective cooling (SCC) to overcome the absence of cooling in dry cutting. This method can exploit the advantage of the high specific heat capacity of water as a cooling fluid without any reaction between water and magnesium to create a cooling element in the cutting zone. The chip morphologies and surface integrity were analyzed experimentally with varying cutting speeds under SCC and dry cutting. The experimental results revealed that SCC and dry cutting produced saw-tooth or serrated chip formation. The chips produced in dry cutting were continuous, while SCC was short and discontinuous as a result of a severe crack on the back surface of the chip. It was discovered that the grain refinement layer on the machined samples was thinner under SCC turning. SCC machining increased the microhardness of the AZ31 magnesium alloy by 60.5% from 55 HV to 88.3 HV, while dry turning exhibited a 49% increase in microhardness. The result revealed that surface roughness improved by 10.8%, 9.4% and 4.7% for cutting speeds (V) of 120, 180, and 240 m/min, respectively, under the SCC internal cooling. Based on the result obtained, SCC cutting outperformed dry cutting in terms of chip breakability, grain refinement, microhardness, and surface roughness. Full article

The implementation of magnesium alloys in a multitude of industries has been proven to be a mere effect of their attractive light weight, corrosion resistant, and biodegradable properties. These traits allow these materials to portray an excellent sustainable machinability. However, with increasing demand, it is essential to explore sustainable means of increasing production while mitigating reductions in sustainability. The current work aims to assess and optimize the high-speed machinability of AZ91 with the use of a vegetable oil-based minimum quantity lubrication (MQL) system using the grey relational analysis (GRA) on the basis of chip morphology and tool wear. The investigation entailed a full factorial design with MQL flow rate, cutting speed, and feed rate as the control parameters and flank wear, land width, chip contact length, saw-tooth pitch, chip segmentation ratio, chip compression ratio, and shear angle as the output responses. The optimal control parameters predicted and experimentally confirmed were an MQL flow rate of 40 mL/h, cutting speed of 300 m/min, and feed rate of 0.3 mm/rev. The usage of said optimal parameters results in a grey relational grade improvement of 0.2675 in comparison to the referenced first experimental run. Moreover, the MQL flow rate was regarded as the critical variable with a contribution percentage of 20% for the grey relational grade. Full article

The machinability of materials is highly affected by their hardness, and it affects power consumption, cutting tool life as well as surface quality while machining the component. This work deals with machining of annealed AISI 4340 alloy steel using a coated carbide tool under a dry environment. The microhardness of annealed and non-annealed workpieces was compared and a significant reduction was found in the microhardness of annealed samples. Microstructure examination of the annealed sample revealed the formation of coarse pearlite which indicated a reduction of hardness and improved ductility. A commercially CVD multilayer (TiN/TiCN/Al₂O₃/ZrCN) coated cemented carbide cutting tool was employed for turning quenched and tempered structural AISI 4340 alloy steel by varying machining speed, rate of feed, and depth of cut to evaluate the surface quality, machining forces, flank wear, and chip morphology. According to the findings of experiments, the feed rate possesses a high impact on surface finish, followed by cutting speed. The prominent shape of the serrated saw tooth chip was noticed at a higher cutting speed. Machined surface finish and cutting forces during turning is a function of the wear profile of the coated carbide insert. This study proves that annealing is a low-cost and economical process to enhance the machinability of alloy steel. Full article

In this study, a biochip was fabricated using a light-absorbing layer of a silicon solar element combined with serrated, interdigitated electrodes and used to identify four different types of cancer cells: CE81T esophageal cancer, OE21 esophageal cancer, A549 lung adenocarcinoma, and TSGH-8301 bladder cancer cells. A string of pearls was formed from dielectrophoretic aggregated cancer cells because of the serrated interdigitated electrodes. Thus, cancer cells were identified in different parts, and electron–hole pairs were separated by photo-excited carriers through the light-absorbing layer of the solar element. The concentration catalysis mechanism of GSH and GSSG was used to conduct photocurrent response and identification, which provides the fast, label-free measurement of cancer cells. The total time taken for this analysis was 13 min. Changes in the impedance value and photocurrent response of each cancer cell were linearly related to the number of cells, and the slope of the admittance value was used to distinguish the location of the cancerous lesion, the slope of the photocurrent response, and the severity of the cancerous lesion. The results show that the number of cancerous cells was directly proportional to the admittance value and the photocurrent response for all four different types of cancer cells. Additionally, different types of cancer cells could easily be differentiated using the slope value of the photocurrent response and the admittance value. Full article

The machining of nickel-based super alloys is challenging, owing to the generation of high cutting temperatures, as well as difficulty in maintaining dimensional accuracy and minimizing surface roughness, which compels the use of cutting fluids for reducing these issues due to efficient cooling/lubrication strategies. The present work investigates the comparative performance of four cooling/lubrication techniques: dry cutting, wet, minimum quantity lubricant (MQL) and compressed-air modes in turning Nitronic 60 steel using a new-generation SiAlON ceramic inserts. Several machinability parameters were analyzed for performance evaluation. For this purpose, 16 cycles of turning trials were performed based on Taguchi’s L₁₆ orthogonal array experimental design by varying cutting conditions and lubrication modes. MQL exhibits beneficial effects as compared to the other lubrication conditions concerning low cutting force, improved surface finish, decreased cutting temperature, longer tool life, and lower white layer thickness on machined surface. Burr formation on the saw-tooth chip surface, as well as friction, greatly influenced the tool flank wear due to improper cooling and poor lubrication approach in dry, wet, and compressed-air-cooled machining environments in comparison to MQL-machining. From an economical perspective, the tool life in MQL machining improved by 11%, 72%, and 138% in the comparison with flooded, compressed-air, and dry conditions, respectively. The results of the study demonstrate that using the MQL system can help with heat extraction capability, and provide some promising outcomes. Full article

Cutting, as the most widely used machining process, is applied in both primary and secondary wood processing. Optimum cutting conditions that result in the high quality of the machined surface and low energy consumption are crucial for wood processing. The effects of the feed speed, cutting speed and average chip thickness on the energy consumption and surface temperature of a circular saw blade during the cutting process of two types of plywood with a thickness of h = 14 mm is described in this paper. In experimental measurements, two circular saw blades with cutting tungsten carbide inserts for wood were used as tools. One circular saw blade was standard, and was not surface treated (CSB1), and second circular saw blade (CSB2) differed by the powder coating surface and the length of the cutting edge. In the experiment, the energy consumption and the surface temperature of the circular saw blade was measured in order to find the optimal cutting conditions for the most energy-efficient cutting process. The results show that the cutting power and the surface temperature of the circular saw blade increased when the feed speed increased. The investigated values of the surface-treated circular saw blade were lower compared to the values of the standard circular saw blade. When comparing the lightweight plywood with the classic plywood, experimentally obtained cutting power values of the circular saw were made 19% lower on average by using the circular saw blade CSB1. When using the CSB2 circular saw blade, these values of the cutting power of the circular saw were 22% lower on average. The surface temperature of the circular saw blade is the highest on the outer edge (tooth root area 31.7 °C) and decreases towards the center of the circular saw blade. There must be a reasonable compromise between machine productivity and energy consumption. Full article

Sustainable manufacturing has received great attention in the last few decades for obtaining high quality products with minimal costs and minimal negative impacts on environment. Sustainable machining is one of the main sustainable manufacturing branches, which is concerned with improving environmental conditions, reducing power consumption, and minimizing machining costs. In the current study, the performance of three sustainable machining techniques, namely dry, compressed air cooling, and minimum quantity lubrication, is compared with conventional flood machining during the turning of austenitic stainless steel (Nitronic 60). This alloy is widely used in aerospace engine components, medical applications, gas power industries, and nuclear power systems due to its superior mechanical and thermal properties. Machining was performed using SiAlON ceramic tool with four different cutting speeds, feeds and a constant depth of cut. Consequently, various chip characteristics such as chip morphology, chip thickness, saw tooth distance and chip segmentation frequency were analyzed with both optical and scanning electron microscopes. Performance assessment was performed under the investigated cutting conditions. Our results show that the tool life under MQL machining are 138%, 72%, and 11% greater than dry, compressed air, and flooded conditions, respectively. The use of SiAlON ceramic tool results is more economically viable under the MQL environment as the overall machining cost per component is lower ($0.27) as compared to dry ($0.36), compressed air ($0.31), and flooded ($0.29) machining conditions. The minimum quantity lubrication technique outperformed the other investigated techniques in terms of eco-friendly aspects, economic feasibility, and technical viability to improve sustainability. Full article

Cancer cell–immune cell hybrids and cancer immunotherapy have attracted much attention in recent years. The design of efficient cell pairing and fusion chips for hybridoma generation has been, subsequently, a subject of great interest. Here, we report a three-layered integrated Microfluidic Flip-Chip (MFC) consisting of a thin through-hole membrane sandwiched between a mirrored array of microfluidic channels and saw-tooth shaped titanium electrodes on the glass. We discuss the design and operation of MFC and show its applicability for cell fusion. The proposed device combines passive hydrodynamic phenomenon and gravitational sedimentation, which allows the transportation and trapping of homotypic and heterotypic cells in large numbers with pairing efficiencies of 75~78% and fusion efficiencies of 73%. Additionally, we also report properties of fused cells from cell biology perspectives, including combined fluorescence-labeled intracellular materials from THP1 and A549, mixed cell morphology, and cell viability. The MFC can be tuned for pairing and fusion of cells with a similar protocol for different cell types. The MFC can be easily disconnected from the test setup for further analysis. Full article

Considering that iron-based super alloy is a kind of difficult-to-cut material, it is easy to produce work hardening and serious tool wear during machining. Therefore, this work aims to explore the chip change characteristics and tool wear mechanism during the processing of iron-based super alloy, calculate the fractal dimensions of chip morphology and tool wear morphology, and use fractals to analyze their change trend. Meanwhile, a new cutting tool with a super ZX coating is used for a high-speed dry turning experiment. The results indicate that the morphology of the chip is saw-tooth, and its color changes gradually, due to the oxidation reaction. The main wear mechanisms of the tool involve abrasive wear, adhesive wear, oxidation wear, coating spalling, microcracking and chipping. The fractal dimension of the tool wear surface and chip is increased with the improvement of cutting speed. This work investigates the fractal characteristics of chip morphology and tool wear morphology. The fractal dimension changes regularly with the change of tool wear, which plays an important role in predicting this tool wear. It is also provides some guidance for the efficient processing of an iron-based super alloy. Full article

The in-situ TiB₂/7050Al composite is a new kind of Al-based metal matrix composite (MMC) with super properties, such as low density, improved strength, and wear resistance. This paper, for a deep insight into its cutting performance, involves a study of the chip formation process and finite element simulation during orthogonal cutting in-situ TiB₂/7050Al MMC. With chips, material properties, cutting forces, and tool geometry parameters, the Johnson–Cook (J–C) constitutive equation of in-situ TiB₂/7050Al composite was established. Then, the cutting simulation model was established by applying the Abaqus–Explicit method, and the serrated chip, shear plane, strain rate, and temperature were analyzed. The experimental and simulation results showed that the obtained material’s constitutive equation was of high reliability, and the saw-tooth chips occurred commonly under either low or high cutting speed and small or large feed rate. From result analysis, it was found that the mechanisms of chip formation included plastic deformation, adiabatic shear, shearing slip, and crack extension. In addition, it was found that the existence of small, hard particles reduced the ductility of the MMC and resulted in segmental chips. Full article

Microstructure and chip formation were evaluated during the step shoulder down-milling of Ti-6Al-4V using a water-miscible vegetable oil-based cutting fluid. Experiments were conducted using the Cut-list fluid supply system previous developed by the authors and a conventional cutting fluid supply system. A thin plastically deformed layer below the machined surface was observed during the metallurgical investigation of the surfaces produced using both systems. Despite noticeable reductions in cutting fluid consumption achieved by Cut-list, no significant disparity was found in microstructural damage. The microstructure of the machined surfaces was strongly affected by cutting speed and fluid flow rate with a discontinuous serrated chip being the principal type. However, increases in cutting fluid flow rate associated with increased cutting speed significantly changed chip morphology where average distance between chip segments increased with cutting speed. Cut-list produced smaller saw-tooth height and larger segmented width, while the transition from aperiodic to periodic serrated chip formation was governed by cutting speed and feed rate. Chip segmentation frequency and shear angle were also sensitive to cutting speed. Full article