Search Results (82)

This paper presents the design, fabrication, and experimental evaluation of a capacitive micromachined ultrasonic transducer (CMUT) linear array for non-contact thickness measurement of marine engineering structures. A 16-element CMUT array was fabricated using a silicon–silicon wafer bonding process, and encapsulated in polyurethane to ensure acoustic impedance matching and environmental protection in underwater conditions. The acoustic performance of the encapsulated CMUT was characterized using standard piezoelectric transducers as reference. The array achieved a transmitting sensitivity of 146.82 dB and a receiving sensitivity of −229.55 dB at 1 MHz. A complete thickness detection system was developed by integrating the CMUT array with a custom transceiver circuit and implementing a time-of-flight (ToF) measurement algorithm. To evaluate environmental robustness, systematic experiments were conducted under varying water temperatures and salinity levels. The results demonstrate that the absolute thickness measurement error remains within ±0.1 mm under all tested conditions, satisfying the accuracy requirements for marine structural health monitoring. The results validate the feasibility of CMUT-based systems for precise and stable thickness measurement in underwater environments, and support their application in non-destructive evaluation of marine infrastructure. Full article

The motivation of this work is to enable the use of piezoelectric micromachined ultrasonic transducer (PMUT)-based implants within the human body for biomedical applications, particularly for power and data transfer for implanted medical devices. To protect surrounding tissue and ensure PMUT functionality over time, biocompatible and hermetic encapsulation is essential. This study investigates the impact of Parylene F-VT4 layers of various thicknesses as well as the effect of multilayer stacks of Parylene F-VT4 combined with atomic layer-deposited nanolayers of Al₂O₃ and HfO₂ on the mechanical and acoustic properties of PMUTs. PMUTs with various diameters (40 µm, 60 µm, and 80 µm) are fabricated and tested both as stand-alone devices and as arrays. The mechanical behavior of single stand-alone PMUT devices is characterized in air and in water using laser Doppler vibrometry (LDV), while the acoustic output of arrays is evaluated by pressure measurements in water. Experimental results reveal a non-monotonic change in resonance frequency as a function of increasing encapsulation thickness due to the competing effects of added mass and increased stiffness. The performance of PMUT arrays is clearly influenced by the encapsulation. For certain array designs, the encapsulation significantly improved the arrays’ pressure output, a change that is attributed to the change in the acoustic wavelength and inter-element coupling. These findings highlight the impact of encapsulation in modifying and potentially enhancing PMUT performance. Full article

Ultrasonic applications such as non-destructive testing, biomedical imaging or range measurements are currently based on piezoelectric bulk transducers. Yet, these kinds of transducers with their mm to cm dimensions are rather impractical in fields in which both frequencies in the kHz region and small-feature sizes are required. This fact mainly relates to the inverse relationship between the resonance frequency constant and the transducers’ dimension, yielding a higher frequency and attenuation with a decreasing size. Piezoelectric micromachined ultrasonic transducers (PMUTs), in comparison, incorporate a small-scale µm design while preserving the operating frequency in the desired kHz range. This contribution presents the detailed manufacturing of such a PMUT with a multiple ring electrode‑based structure to additionally adjust the sound pressure fields. The PMUT will be characterized by its deflection in air along with the characterization of the piezoelectric material lead zirconate titanate (PZT) itself. The measurements showed a maximum polarization of 21.8 µC/cm² at 50 kV/cm, the PMUT’s displacement of 30.50 nm/V in air when all electrodes are driven, and an adjustable deflection via different electrode excitations without the need for additional hardware. The ring design also offered the possibility to emit two distinct frequencies simultaneously. These results demonstrate the potential of the designs for small-feature-size applications as they are in high demand for implantable devices, miniaturized ultrasonic-based communication or drug delivery. Full article

Speech recognition in noisy environments has long posed a challenge. Air conduction microphone (ACM), the devices typically used, are susceptible to environmental noise. In this work, a customized bone conduction microphone (BCM) system based on a piezoelectric micromachined ultrasonic transducer is developed to capture speech through real-time bone conduction (BC), while a commercial ACM is integrated for simultaneous capture of speech through air conduction (AC). The system enables simpler and more robust BC speech capture. The BC speech capture achieves a signal-to-noise amplitude ratio over five times greater than that of AC speech capture in an environment with a noise level of 68 dB. Instead of using only AC-captured speech, both BC- and AC-captured speech are input into a speech enhancement module. The noise-insensitive BC-captured speech serves as a speech reference to adapt the SE backbone of AC-captured speech. The two types of speech are fused, and noise suppression is applied to generate enhanced speech. Compared with the original noisy speech, the enhanced speech achieves a character error rate reduction of over 20%, approaching the speech recognition accuracy of clean speech. The results indicate that this speech enhancement method based on the fusion of BC- and AC-captured speech efficiently integrates the features of both types of speech, thereby improving speech recognition accuracy in noisy environments. This work presents an innovative system designed to efficiently capture BC speech and enhance speech recognition in noisy environments. Full article

This study proposes an innovative health management solution to address the defecation care needs of the elderly population. Traditional post-defecation care methods have significant limitations, particularly imposing a considerable psychological burden on patients. By leveraging the rich physiological information contained in bowel sounds, in this work, we designed and implemented a wearable defecation warning monitor based on scandium aluminum nitride (ScAlN) piezoelectric thin films and piezoelectric micromachined ultrasonic transducers (PMUTs). The proposed device mainly incorporates two core components: a bowel sound signal acquisition module and a real-time signal display graphical user interface (GUI) developed using the MATLAB R2023a platform. The research focuses on the systematic characterization and comparative analysis of the sound pressure sensitivity of three different signal readout structures. Experimental results demonstrate that the differential readout structure exhibits superior sensitivity. By continuously monitoring bowel sounds in healthy subjects both with and without the urge to defecate using the defecation warning monitor and a modified stethoscope, and conducting a comparative analysis of the experimental data, it is verified that the defecation warning monitor has significant advantages in clinical applications and demonstrates promising potential for defecation warning monitoring. Full article

An emerging alternative to conventional piezoelectric technologies, which continue to dominate the ultrasound medical imaging (US) market, is Capacitive Micromachined Ultrasonic Transducers (CMUTs). Ultrasound transducers based on this technology offer a wider frequency bandwidth, improved cost-effectiveness, miniaturized size and effective integration with electronics. These features have led to an increase in the commercialization of CMUTs in the last 10 years. We conducted a review to answer three main research questions: (1) What are the commercially available CMUT-based clinical sonographic devices in the medical imaging space? (2) What are the medical imaging applications of these devices? (3) What is the performance of the devices in these applications? We additionally reported on all the future work expressed by modern studies released in the past 2 years to predict the trend of development in future CMUT device developments and express gaps in current research. The search retrieved 19 commercially available sonographic CMUT products belonging to seven companies. Four of the products were clinically approved. Sonographic CMUT devices have established their niche in the medical US imaging market mainly through the Butterfly iQ and iQ+ for quick preliminary screening, emergency care in resource-limited settings, clinical training, teleguidance, and paramedical applications. There were no commercialized 3D CMUT probes. Full article

PMUTs have been widely studied in recent years, particularly those based on the SOI (silicon-on-insulator) process, which have been partially commercialized and are extensively used in advanced applications such as ultrasonic ranging and spatial positioning. However, there has been little research on their high-temperature reliability, a critical area for their use in extreme environmental conditions. In this study, we investigate the high-temperature characteristics of air-coupled PMUTs based on SOI under various structural conditions, employing both finite element analysis (FEA) and experimental validation. We assess the performance of PMUTs at elevated temperatures by examining key parameters such as resonant frequency, the electromechanical coupling coefficient, mechanical amplitude, and warpage, all analyzed as functions of temperature. The experimental results show that temperature-induced drift becomes more significant as the back cavity size increases and the top silicon layer thickness decreases. These findings are consistent with the trends observed in the finite element analysis. Specifically, a PMUT with a back cavity diameter of 1000 $\mathsf{\mu }$m and a top silicon thickness of 4 $\mathsf{\mu }$m exhibits a temperature drift rate of up to 47.3% when the operating temperature rises from room temperature to 200 °C. Furthermore, at elevated temperatures, the maximum electromechanical coupling coefficient improves by 68.6%, and the mechanical amplitude increases by 66.1%. Heating experiments using a 3D profiler reveal that warpage increases from 0.3 $\mathsf{\mu }$m to 2.15 $\mathsf{\mu }$m as the temperature reaches 150 °C. These findings offer important theoretical insights into the temperature-induced drift behavior of PMUTs under high-temperature conditions. This study provides a comprehensive understanding of the performance variations of PMUTs, including changes in electromechanical coupling, mechanical amplitude, and structural warpage, which are critical for their reliable operation in extreme environments. The results presented here can serve as a foundation for the design and optimization of PMUTs in applications that require high-temperature stability, ensuring their enhanced reliability and performance in such demanding conditions. Full article

Due to their compact sizes, low power consumption levels, and convenient integration capabilities, piezoelectric micromachined ultrasonic transducers (PMUTs) have gained significant attention for enabling environmental sensing functionalities. However, the frequency inconsistency of the PMUT arrays often leads to directional errors with the ultrasonic beams. Herein, we propose a reconfigurable PMUT array based on a Sc_0.2Al_0.8N piezoelectric thin film for in-air ranging. Each element of the reconfigurable PMUT array possesses the ability to be independently replaced, enabling matching of the required frequency characteristics, which enhances the reusability of the device. The experimental results show that the frequency uniformity of the 2 × 2 PMUT array reaches 0.38% and the half-power beam width (θ_−3dB) of the array measured at 20 cm is 60°. At a resonance of 69.7 kHz, the sound pressure output reaches 7.4 Pa (sound pressure level of 108.2 dB) at 19 mm, with a reception sensitivity of approximately 11.6 mV/Pa. Ultimately, the maximum sensing distance of the array is 7.9 m, and it extends to 14.1 m with a horn, with a signal-to-noise ratio (SNR) of 19.5 dB. This research significantly expands the ranging capability of PMUTs and showcases their great potential in environmental perception applications. Full article

Piezoelectric micromachined ultrasonic transducers (PMUTs) show considerable promise for application in ultrasound imaging, but the limited bandwidth of the traditional PMUTs largely affects the imaging quality. This paper focuses on how to arrange cells with different frequencies to maximize the bandwidth and proposes a multi-frequency PMUT (MF-PMUT) linear array. Seven cells with gradually changing frequencies are arranged in a monotonic trend to form a unit, and 32 units are distributed across four lines, forming one element. To investigate how the arrangement of cells affects the bandwidth, three different arrays were designed according to the extent of unit aggregation from the same frequency. Underwater experiments were conducted to assess the acoustic performance, especially the bandwidth. We found that the densest arrangement of the same cells produced the largest bandwidth, achieving a 92% transmission bandwidth and a 50% burst-echo bandwidth at 6 MHz. The mechanism was investigated from the coupling point of view by finite element analysis and laser Doppler vibrometry, focusing on the cell displacements. The results demonstrated strong ultrasound coupling in the devices, resulting in larger bandwidths. To exploit the advanced bandwidth but reduce the crosstalk, grooves for isolation were fabricated between elements. This work proposes an effective strategy for developing advanced PMUT arrays that would benefit ultrasound imaging applications. Full article

Piezoelectric micromachined ultrasonic transducers (PMUTs) have been widely applied in distance sensing applications. However, the rapid movement of miniature robots in complex environments necessitates higher ranging capabilities from sensors, making the enhancement of PMUT sensing distance critically important. In this paper, a scandium-doped aluminum nitride (ScAlN) PMUT based on a flexurally suspended membrane is proposed. Unlike the traditional fully clamped design, the PMUT incorporates a partially clamped membrane, thereby extending the vibration displacement and enhancing the output sound pressure. Experimental results demonstrate that at a resonant frequency of 78 kHz, a single PMUT generates a sound pressure level (SPL) of 112.2 dB at a distance of 10 mm and achieves a high receiving sensitivity of 12.3 mV/Pa. Distance testing reveals that a single PMUT equipped with a horn can achieve a record-breaking distance sensing range of 11.2 m when used alongside a device capable of simultaneously transmitting and receiving ultrasound signals. This achievement is significant for miniaturized and integrated applications that utilize ultrasound for long-range target detection. Full article

This paper introduces a novel design for a liquid-deployed Piezoelectric Micromachined Ultrasonic Transducer (PMUT). This design was specifically developed to resonate at a lower ultrasonic frequency than a PMUT with a circular, fully clamped diaphragm with the same diameter. Furthermore, the novel design was also optimised to enhance its ultrasonic radiation reception capabilities. These parametric enhancements were necessary to develop a PMUT device that could form part of an eventual microscale sensory device used for the Structural Health Monitoring (SHM) of reinforced concrete (RC) structures. Through these two enhancements, an eventual microscale sensor can be made smaller, thus taking up a smaller die footprint and also be able to be deployed further apart from each other. Eventually, this would reduce the developed distributed sensor system’s cost. The innovative design employed a configuration where the diaphragm was only pinned at particular points along its circumference. This paper presents results from Finite Element Modelling (FEM), as well as experimental work that was conducted to develop and test this novel PMUT. The experimental work presented involved both laser vibrometry and ultrasonic radiation lab work. The results show that when compared to a clamped diaphragm design, the novel device managed to achieve the required reduction in resonant frequency and presented an enhanced sensitivity to incoming ultrasonic radiation. Full article

Ultrasound is widely applied in diverse domains, such as medical imaging, non-destructive evaluation, and acoustic communication. Piezoelectric micromachined ultrasonic transducers (PMUTs) capable of generating and receiving ultrasonic signals at the micrometer level have become a prominent technology in the field of ultrasound. It is important to enrich the models of the PMUTs to meet the varied applications. In this study, a series of PMUT devices featured with various top electrode configurations, square, circular, and doughnut, were designed to assess the influence of shape on the emission efficacy. It was demonstrated that the PMUTs with a circular top electrode were outperformed, which was calculated from the external acoustic pressure produced by the PMUTs operating in the fundamental resonant mode at a specified distance. Furthermore, the superior performance of PMUT arrays were exhibited through computational simulations for the circular top electrode geometries. Conventional microelectromechanical systems (MEMS) techniques were used to fabricate an array of PMUTs based on aluminum nitride (AlN) films. These findings make great contributions for enhancing the signal transmission sensitivity and bandwidth of PMUTs, which have significant potential in non-destructive testing and medical imaging applications. Full article

In this paper, we present a bolt preload monitoring system, including the system architecture and algorithms. We show how Finite Element Method (FEM) simulations aided the design and how we processed signals to achieve experimental validation. The preload is measured using a Piezoelectric Micromachined Ultrasonic Transducer (PMUT) in pulse-echo mode, by detecting the Change in Time-of-Flight (CTOF) of the acoustic wave generated by the PMUT, between no-load and load conditions. We performed FEM simulations to analyze the wave propagation inside the bolt and understand the effect of different configurations and parameters, such as transducer bandwidth, transducer position (head/tip), presence or absence of threads, as well as the frequency of the acoustic waves. In order to couple the PMUT to the bolt, a novel assembly process involving the deposition of an elastomeric acoustic impedance matching layer was developed. We achieved, for the first time with PMUTs, an experimental measure of bolt preload from the CTOF, with a good signal-to-noise ratio. Due to its low cost and small size, this system has great potential for use in the field for continuous monitoring throughout the operative life of the bolt. Full article

This paper delves into enhancing the performance of ScAlN-based Piezoelectric Micromachined Ultrasonic Transducers (PMUTs) through the implementation of Polydimethylsiloxane (PDMS) acoustic lenses. The PMUT, encapsulated in PDMS, underwent thorough characterization through the utilization of an industry-standard hydrophone calibration instrument. The experimental results showed that the ScAlN-based PMUT with the PDMS lenses achieved an impressive sensitivity of −160 dB (re: 1 V/μPa), an improvement of more than 8 dB compared to the PMUT with an equivalent PDMS film. There was a noticeable improvement in the −3 dB main lobe width within the frequency response when comparing the PMUT with PDMS encapsulation, both with and without lenses. The successful fabrication of high-performance PDMS lenses proved instrumental in significantly boosting the sensitivity of the PMUT. Comprehensive performance evaluations underscored that the designed PMUT in this investigation surpassed its counterparts reported in the literature and commercially available transducers. This encouraging outcome emphasizes its substantial potential for commercial applications. Full article

To address the requirements of sonar imaging, such as high receiving sensitivity, a wide bandwidth, and a wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with the SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a −6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of 1.37 V/μPa/mm², which significantly surpasses the performance of previously reported PMUTs. The −6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured as 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity compared to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of AlN PMUTs in future studies. Full article