Search Results (6,421)

Activated carbons are usually prepared from natural precursors (e.g., fruit stones or nutshells) by carbonization and activation processes carried out at 400–1000 °C. They exhibit well-developed porosity, and chemical activation introduces hydrophilic functional groups on their surface, providing excellent sorption properties. However, the high temperatures required during thermal treatment increase production costs. In this work, cost-reducing methods for preparing carbon sorbents are proposed. Carbonization of H₃PO₄ activated waste pistachio nutshells was performed using classical pyrolysis (500 or 550 °C, 30 min, N₂ atmosphere) and microwave treatment (power 1000 W, 20 min). The properties of the synthesized carbons were characterized using thermogravimetry and spectroscopic techniques including infrared (ATR), Raman, photoelectron (XPS) spectroscopies, and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS). Porous structure parameters were determined using nitrogen adsorption experiments. The efficiency of Pb²⁺ removal from spiked ultrapure, tap and river water was evaluated by batch sorption experiments and inductively coupled plasma–mass spectrometry. The most porous carbons were those prepared at 500 and 550 °C, with specific surface areas of 910 and 256 m²/g, respectively. Surface phosphates increased the Pb²⁺ sorption efficiency to 99% from ultrapure water, at an initial concentration of 300 µg Pb²⁺/L. The material obtained with the microwave method was not fully carbonized and remained nonporous, but it also exhibited 99% Pb²⁺ uptake from ultrapure water due to the presence of oxygen-containing surface groups. The Pb²⁺ removal from spiked tap and river water reached up to 84% and 94%, respectively, at the spiking level of 300 µg Pb²⁺/L. Full article

The rational design of electrode materials with tailored composition and architecture is crucial for advancing high-capability electrochemical energy storage systems. This study reports that gadolinium-modified NiFe₂O₄ nanosheet electrodes were effectively synthesized on nickel foam via a hydrothermal approach followed by thermal treatment. A series of compositions (NiFe, NiFe–Gd1, NiFe–Gd2, and NiFe–Gd3) were prepared to systematically examine the effect of Gd incorporation on structural features and electrochemical properties. X-ray diffraction (XRD) analysis confirmed the formation of the cubic spinel NiFe₂O₄ phase without detectable secondary phases, indicating that the crystal structure remains intact after Gd introduction. X-ray photoelectron spectroscopy (XPS) further verified the presence of Ni²⁺, Fe³⁺, and Gd³⁺ species within the lattice environment. Morphological analysis using field-emission scanning electron microscopy (FESEM) revealed a nanosheet-based architecture, where the optimized NiFe–Gd2 electrode exhibited a porous and interconnected nanosheet framework with abundant exposed edges. This structural configuration improves electrolyte penetration and facilitates efficient ion transport during charge storage processes. Electrochemical measurements demonstrated that the NiFe–Gd2 electrode delivers an areal capacitance of 5235 mF cm⁻² at 10 mA cm⁻², along with improved reaction kinetics and low internal resistance. An asymmetric supercapacitor assembled using NiFe–Gd2 as the positive electrode and activated carbon as the negative electrode operated stably within a 0–1.5 V potential window, achieving an energy density of 0.136 mWh cm⁻² and a power density of 3.14 mW cm⁻², while retaining 86.55% of its initial capacitance after 7000 cycles. These results highlight the potential of rare-earth engineering as a viable strategy for designing advanced spinel ferrite electrodes and pave the way for the development of high-performance, durable, and scalable supercapacitor systems for practical energy storage applications. Full article

Biosensors based on electrolyte-gated organic field-effect transistors (EGOFETs) have attracted considerable attention due to their advantages, including low cost, inherent signal amplification, and low-voltage operation. A critical step influencing sensing performance is the integration of specific receptors onto the device surface. Among various strategies, the covalent immobilization of biorecognition elements onto gold surfaces via thiol chemistry is one of the most widely used approaches. In this study, we report the optimization of a mixed self-assembled monolayer (SAM) composed of 11-mercaptoundecanoic acid (11-MUA) and 3-mercaptopropionic acid (3-MPA) for label-free detection of human IgG using EGOFETs. The quality of the SAM was systematically modulated by varying the total concentration from 10 to 400 mM and characterized using X-ray Photoelectron Spectroscopy (XPS), Electrochemical Impedance Spectroscopy (EIS), Cyclic Voltammetry (CV), and Atomic Force Microscopy (AFM). The results revealed that a concentration of 50 mM yielded a densely packed and well-ordered monolayer. After covalent immobilization of anti-IgG antibodies via 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride/N-hydroxysuccinimide (EDC/NHS) chemistry and subsequent blocking with ethanolamine and bovine serum albumin (BSA), the functionalized gate electrodes were integrated into poly(3-hexylthiophene) (P3HT)-based EGOFETs. Electrical measurements demonstrated that EGOFET biosensors functionalized with the 50 mM SAM achieved optimal sensing performance. The devices exhibited a highly linear response (R² = 0.998) over a wide concentration range from 1 fM to 10 nM, with a LOD of 2.82 fM, and showed excellent selectivity against non-target immunoglobulins A and M (IgA and IgM). This SAM concentration optimization strategy provides a versatile approach for engineering high-performance EGOFET biosensors, with potential applicability to a broad range of disease biomarkers. Full article

Biopolymer-based packaging films possess outstanding performances and are being developed as the alternatives to traditional petroleum-based plastic packaging films with many non-ignorable shortcomings. In this study, chitosan, succinylated pullulan (SP), and berberine (BBR) were combined to fabricate novel biopolymer-based composite films (CSSPB) via the layer-by-layer assembly method. The effects of the incorporation of BBR on the physicochemical properties of the film were investigated. It was found that after BBR was added, the tensile strength (TS), elongation at break (EAB), hydrophobicity, and antioxidant capacities of the film were enhanced. The chemical bonding, crystalline properties, elemental composition, and thermal stability of the films were also characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA), respectively. The in vitro antifungal tests revealed the antifungal activities of the films with a relatively high BBR content against Colletotrichum gloeosporioides (CG). In the preservation experiments, the CSSPB films exhibited preservation effects on fresh-cut apples, which manifested as delaying browning, weight loss, an increase in the soluble solids content, and a decrease in hardness. The new CSSPB composite films were opined to hold application potential in the field of food packaging. Full article

UV-C irradiation enables digital zirconia colouring. This study investigates the atomic mechanism driving this defect-induced optical change. The band gap was calculated from the absorption spectra with the Tauc plot. The absorption spectra were measured using UV–visible spectroscopy. The surface composition was evaluated through X-ray photoelectron spectroscopy (XPS). The location of the oxygen vacancy was tested through electron paramagnetic resonance (EPR). The computer calculation using Density Functional Theory was conducted and the density of states (DOSs) were calculated. The band gap reduced rapidly from the baseline group (3.184 eV) to the 30 min irradiated group (3.097 eV). The XPS results showed that the electron density around O1s reduced and the electron density around Zr 3d increased. The EPR signal (g = 2.0037) increases progressively as the UV-C irradiation time is prolonged from 15 min to 24 h, indicating the accumulation of paramagnetic defect centres. The DOSs suggested the emergence of defect-associated states and band-edge tailing in oxygen deficient models, consistent with the experimentally observed reduction in the Tauc-derived optical band gap. This study confirmed the mechanism by which UV-C-induced oxygen vacancies modify the colour of 3Y-TZP. Full article

LaFeO₃ nanofibers and Ag-doped LaFeO₃ nanofibers were fabricated via an approach combining electrospinning with calcination. Their crystal structures, micro-morphologies, and chemical compositions were determined by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and Fourier-transform infrared spectroscopy. In addition, the conduction mechanisms and magnetic properties of the two samples were investigated using a semiconductor analyzer and a vibrating sample magnetometer. Rietveld refined X-ray diffraction analyses confirmed the orthorhombic structure. The two samples showed a nanofibrous structure. For Ag-doped LaFeO₃, the conduction was dominated by the ohmic conduction mechanism in a low-resistance state, while it was governed by space-charge-limited current conduction in a high-resistance state. It also showed a high on/off ratio of 3.6 × 10³. The coercivity and remanence values of Ag-doped LaFeO₃ were 200 Oe and 0.000404 emu g⁻¹. This, thus, indicates the considerable application potential of Ag-doped LaFeO₃ for resistive random-access memory devices and magnetoresistive random-access memory devices. Full article

Low-temperature methanation technology offers a promising pathway for carbon recycling and sustainable energy storage by enabling near-equilibrium CO₂ conversion under atmospheric pressure. However, efficiently activating CO₂ at low temperatures remains a significant challenge due to the kinetic limitations of hydrogenation intermediates. We construct a composite oxide–metal interface structure by anchoring highly dispersed CeCrO_x nanoclusters onto metallic nickel via an ion-exchange method. This catalyst exhibits superior activity compared to conventional Ni/oxide catalysts with identical composition. Under atmospheric pressure at 220 °C, it achieves nearly 80% CO₂ conversion with over 99% methane selectivity and maintains excellent catalytic performance and structural stability during a 240-h continuous test. Systematic characterizations, including high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, CO₂ temperature-programmed desorption, and in situ DRIFTS reflectance infrared Fourier-transform spectroscopy, reveal that the synergistic modification by CeO₂ and Cr₂O₃ not only optimizes the electronic structure of Ni to promote CO₂ adsorption and activation, but also enhances H₂ dissociation and intermediate conversion by regulating oxygen vacancy concentration and alkaline site distribution. Mechanistic studies indicate that the reaction follows a synergistic mechanism dominated by the formate pathway and assisted by the CO pathway. Moreover, the interfacial structure effectively stabilizes active sites and inhibits carbon deposition from CH₄ decomposition. This study provides a universal and effective strategy for designing Ni-based CO₂ conversion catalysts suited for mild reaction conditions and characterized by high energy efficiency. Full article

Recently, diamond-like carbon (DLC) films have been considered for enhancing the wear resistance of rubber because rubber exhibits a high coefficient of friction and is prone to wearing out. However, the significant difference in thermal expansion coefficients between DLC films and rubber often leads to high residual stresses and poor interfacial adhesion, which limits their application in dynamic seals. In this study, Cr-C/DLC composite films were prepared using magnetron sputtering, and the effects of varying Cr contents (0.8 at.%, 1.4 at.%, 4.3 at.%, and 7.0 at.%) on interfacial adhesion and tribological properties were investigated. Scanning electron microscopy (SEM) analysis revealed no distinct demarcation lines in the composite films, indicating strong adhesion to the substrate. X-ray photoelectron spectroscopy (XPS) analysis revealed that chromium doping promoted the conversion of sp³ bonds to sp² bonds. Adhesion and tribology tests revealed that introducing a Cr-C layer with higher Cr content within the range of 0.8 at.% to 7.0 at.% enhanced the film’s adhesion, reducing the CoF value of the composite film to 0.13–0.14. Specifically, the RF80 sample (4.3 at.% Cr) exhibited excellent interfacial adhesion and optimal tribological performance, with a CoF value reduced to 0.13 and wear rate of 3.1 × 10⁻⁴ mm³/(Nm). In summary, modulating the Cr doping content can significantly enhance the interfacial adhesion strength and tribological properties of Cr-C/DLC composite films on rubber surfaces, providing an effective solution for optimizing rubber seals. Full article

Janus nanoparticles (JNPs) synthesis has caught the scientific community’s attention due to their amphiphilic properties and extensive areas of application. In this work, different new copper–silica-based and silica-based JNPs were synthesized using a novel masking methodology and a self-assembly method based on sol–gel procedures, respectively. Moreover, various techniques were used to characterize the developed nanomaterials, including scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). Two types of copper–silica-based Janus nanoparticles were synthesized with a 40 to 70 nm size, while SiO₂-based JNPs of around 135 nm were obtained. The duality of different JNPs was confirmed by SEM and by a simple and economical route based on an emulsion stabilization path: analyzing dispersion/aggregation and associated behavior at the immiscible solvent interface. JNPs exhibited an extended residence time over 20 days at an immiscible solvent interface, thereby enhancing the resulting emulsion interface stability. This behavior highlighted their amphiphilic characteristics in comparison to conventional nanoparticles. Consequently, a procedure to determine nanoparticle amphiphilicity could be further standardized. Full article

Efficient charge transfer and effective separation of photo-generated charge carriers are pivotal to the photocatalytic process. In this study, a novel CoAl₂O₄@nitrogen-doped graphitic carbon (CoAl₂O₄@NGC) composite photocatalyst was fabricated via a stepwise hydrothermal method coupled with high-temperature calcination, and its photocatalytic performance for CO₂ reduction was systematically investigated. X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoelectrochemical measurements were employed to characterize the phase structure, microstructure, surface chemical state and photoelectrochemical properties of the catalyst. Spinel-structured CoAl₂O₄ nanoparticles were uniformly anchored on the NGC substrate, forming a well-integrated composite interface. XPS analysis confirmed the coexistence of Co²⁺/Co³⁺ mixed valence states in CoAl₂O₄ which provides abundant redox sites for CO₂ activation. Photocatalytic tests showed that CoAl₂O₄@NGC exhibits excellent catalytic activity and cycling stability, with CO and CH₄ yields of 27.88 μmol·g⁻¹·h⁻¹ and 23.90 μmol·g⁻¹·h⁻¹, respectively. The narrow bandgap (1.54 eV) enhances visible light absorption, while efficient electron-hole separation and reduced charge transfer resistance improve photocatalytic efficiency. Theoretical calculations further reveal that CoAl₂O₄@NGC lowers the adsorption free energy of CO₂ and the energy barrier for COOH formation, thus facilitating the photocatalytic CO₂ reduction. This work provides insights for the design of efficient and stable photocatalysts for CO₂ reduction and deepens the understanding of the synergistic catalytic mechanism in the spinel/nitrogen-doped carbon composite system. Full article

In this study, Ti-Co-Ce getter films were deposited via magnetron sputtering to investigate their activation mechanism—the thermal removal of surface passivation layers to restore gas sorption capability. The morphology before and after film activation was characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The oxygen content on the film surface before and after activation was measured using an energy-dispersive X-ray spectrometer (EDS), and gas desorption during activation was monitored with a quadrupole mass spectrometer (QMS). The combined results confirmed the absence of O₂ desorption during activation, suggesting oxygen migration into the film bulk. Crucially, in situ X-ray photoelectron spectroscopy (XPS) combined with controlled Ar⁺ ion sputtering depth profiling (0–30 nm) was employed to directly probe the chemical-state evolution within the thin film before and after thermal activation at 400 °C, thereby providing direct evidence of the activation dynamics. The data reveal that within the 0–10 nm near-surface region, a strong oxygen chemical potential gradient drives rapid oxide reduction and inward migration of lattice oxygen. At depths of 20–30 nm, moderate reduction coupled with oxygen enrichment induces phase separation, while around 30 nm, a dynamic equilibrium between oxygen inflow and outflow is established. These findings provide a theoretical basis for optimizing activation processes and guiding the development of low-temperature getter materials. This work is particularly relevant for MEMS, vacuum electronics, and other applications with stringent thermal budgets, expanding the design possibilities for heat-sensitive device integration. Full article

High-quality direct reduced iron (DRI) powder is essential for applications in catalysis, adsorption, and electromagnetic materials. However, its tendency to reoxidize during processing presents a significant challenge. This study investigates the oxidation behavior of DRI powder during wet ball-milling treatment. Samples were characterized using chemical phase dissolution, X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) to assess both bulk and surface oxidation. The results reveal that significant oxidation occurs during the wet grinding and subsequent processing stages, with the relative oxidation degree (ROD) of the iron powder increasing sharply from 6.08% to 26.81% as the grinding time is extended from 20 to 40 min. SEM-EDS analysis indicates that oxidation is particularly pronounced in particles smaller than 10 μm. XRD confirms the gradual transformation of Fe⁰ to Fe₃O₄ with prolonged grinding, corroborating the chemical analysis. Furthermore, XPS analysis of the Fe 2p, Fe 3p, Fe 3s, and O 1s core levels reveals that the nanoscale surface is composed of Fe₂O₃, Fe₃O₄, Fe(OH)₃, and FeOOH—a composition distinctly different from the bulk Fe/Fe₃O₄ phases. These findings underscore the critical roles of particle size and mechanical activation in driving DRI reoxidation during wet milling. Full article

Activated sludge treatment is plagued by high secondary pollution risks, and ship antifouling paint particles (APPs) as hazardous heavy metal-rich solid wastes generated from hull derusting wastewater, pose severe environmental threats and intractable disposal dilemmas. This study developed a novel pilot-scale activated sludge reduction process coupling APPs-derived carbon-based catalysts with ultrasound-Fe²⁺/peroxydisulfate (PDS) advanced oxidation. Columnar catalysts were fabricated via direct carbonization-molding using waste APPs from an 82,000 deadweight bulk carrier were used as the sole raw material to prepare columnar catalysts via direct carbonization-molding; single-factor and orthogonal experiments optimized process parameters, Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray Photoelectron Spectroscopy (XPS) characterized catalyst and sludge properties, free radical quenching experiments elucidated reaction mechanisms and a 90-day continuous pilot run assessed catalytic stability. The process achieved a 43.5% sludge removal rate under optimal conditions, accompanied by 100% toluene and 92.3% phenolic compound degradation, as well as efficient total phosphorus (TP) and total nitrogen (TN) removal. Mechanistic studies via characterization and quenching experiments confirmed the catalyst enhanced PDS activation through free/non-free radical synergy and accelerated Fe²⁺/Fe³⁺ redox cycling. A 90-day continuous pilot operation demonstrated excellent long-term catalytic stability, with sludge removal rate remaining above 38%. This “waste treating waste” technology realizes high-value APPs resource utilization, provides a low-carbon sludge disposal pathway, and offers a scalable solution for collaborative pollution control in the wastewater treatment and shipping industries. Full article

Cu₂ZnSn(S,Se)₄ (CZTSSe) is a candidate thin-film photovoltaic material; however, its performance is restricted by innate defect-induced nonradiative recombination. Low-concentration Ge doping has been identified as an efficient way to mitigate these defects, but the selenization temperature remains an important process parameter that governs the structure and optoelectronic characteristics of CZTSSe absorbers. In the present work, low-concentration Ge-doped Cu₂ZnSn_0.95Ge_0.05S₄ (CZTGS) precursor films were synthesized through a green, n-butylammonium butyrate-based solution approach. The effects of the selenization temperature (530–570 °C) on the microstructure, composition, and photovoltaic performance of Cu₂ZnSn_0.95Ge_0.05(S,Se)₄ (CZTGSSe) films and devices were comprehensively investigated. X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectrometer (EDS), atomic force microscopy (AFM) were performed to comprehensively characterize the synthesized samples, and the results suggested that the selenization temperature dramatically altered the film grain growth, crystallinity, elemental retention and surface roughness. Specifically, the film that underwent selenization at 550 °C presented the best crystallinity, which was accompanied by large-scale even grains, efficient Ge⁴⁺ addition to the kesterite lattice and the lowest surface roughness. These better properties in terms of structure and composition resulted in the lowest carrier transport resistance (R_s = 8.6 Ω∙cm²), improved recombination resistance (R_j = 5.9 kΩ∙cm²), inhibited nonradiative recombination, and prolonged carrier lifetime (τ_EIS = 35.8 μs). Therefore, the resulting CZTGSSe thin-film solar cell had an 8.69% better power conversion efficiency (PCE), while its open-circuit voltage (V_OC) was 0.42 V, the fill factor (FF) was 55.51%, and the short-circuit current density (J_SC) was 37.71 mA·cm⁻². Our results elucidate the mechanism by which the selenization temperature regulates low-concentration Ge-doped kesterite devices and provide more insights into the optimization of processes for cost-effective, high-performance, and green thin-film solar cells. Full article

Based on density functional theory, the structural, mechanical, and photoelectric properties of the perovskite material Cs₂SeCl₆ were systematically studied under pressures ranging from 0 to 50 GPa. Analysis of structural parameters indicates that the lattice constant, unit cell volume, and bond length decrease progressively with increasing pressure. Notably, the material maintains structural stability across the entire pressure range. Electronic property calculations show that Cs₂SeCl₆ retains an indirect band gap under pressure, with the band gap value monotonically decreasing as pressure increases. The orbital contributions remain almost unchanged at different pressures. The conduction band is mainly composed of Cl-p and Se-p orbitals, while the valence band is dominated by Cl-p orbitals. The analysis of the effective mass indicates that the transport capability of charge carriers is enhanced under compression. Mechanical stability and ductility were evaluated by calculating the elastic constants and derived mechanical moduli, confirming that the material remains mechanically stable under high pressure. Optical properties were investigated by computing the dielectric function, reflectivity, refractive index, optical absorption coefficient, and extinction coefficient. Collectively, the findings of this work demonstrate that the pressurized Cs₂SeCl₆ exhibits excellent structural robustness, improved charge transport, and promising photoelectric performance, making it a strong candidate for applications in solar cells and other photoelectronic devices. Full article