Search Results (771)

Persistent reactive azo dyes released from textile finishing are a serious threat to water systems, but effective methods using sunlight to break them down are still limited. Everzol Yellow 3RS (EY-3RS) is particularly recalcitrant: past studies have relied almost exclusively on physical adsorption onto natural or modified clays and zeolites, and no photocatalytic pathway employing engineered nanomaterials has been documented to date. This study reports the synthesis, characterization, and performance of a visible-active ternary nanocomposite, Cu₄O₃/ZrO₂/TiO₂, prepared hydrothermally alongside its binary (Cu₄O₃/ZrO₂) and rutile TiO₂ counterparts. XRD, FT-IR, SEM-EDX, UV-Vis, and PL analyses confirm a heterostructured architecture with a narrowed optical bandgap of 2.91 eV, efficient charge separation, and a mesoporous nanosphere-in-matrix morphology. Photocatalytic tests conducted under midsummer sunlight reveal that the ternary catalyst removes 91.41% of 40 ppm EY-3RS within 100 min, markedly surpassing the binary catalyst (86.65%) and TiO₂ (81.48%). Activity trends persist across a wide range of operational variables, including dye concentrations (20–100 ppm), catalyst dosages (10–40 mg), pH levels (3–11), and irradiation times (up to 100 min). The material retains ≈ 93% of its initial efficiency after four consecutive cycles, evidencing good reusability. This work introduces the first nanophotocatalytic strategy for EY-3RS degradation and underscores the promise of multi-oxide heterojunctions for solar-driven remediation of colored effluents. Full article

TiO₂ was synthesized via the sol–gel method and employed as a support material for the deposition of CdS nanofibers using two novel techniques: impregnation and photodeposition. XRD characterization shows that crystallite size decreases when CdS is incorporated into TiO₂. UV-Vis spectroscopy showed that the bandgap of the CdS/TiO₂ heterostructured nanocomposites decreases compared to the raw TiO₂ support, making them very appropriate for photocatalytic applications in the visible region. The photocatalysts were tested for hydrogen production in methanol–water solutions under visible light conditions. It was observed that the TiC20 photocatalyst prepared by the impregnation method improved the photocatalytic activity compared with photodeposition technique (TiC20FD), achieving a maximum hydrogen production of 570.5 µmol H₂ ${\mathrm{g}}_{\mathrm{c}\mathrm{a}\mathrm{t}}^{-1}$ h⁻¹, while the latter attained 383.4 µmol H₂ ${\mathrm{g}}_{\mathrm{c}\mathrm{a}\mathrm{t}}^{-1}$ h⁻¹. Full article

The natural sunlight driven photocatalytic degradation of organic pollutants is a sustainable solution for water purification. The use of heterojunction nanocomposites in this process shows promise for improved photodegradation efficiency. In this work, nanocrystalline Zn₂SnO₄/SnO₂ obtained by the solid-state synthesis method was tested as a heterojunction photocatalyst material for the degradation of methylene blue (MB) and Rhodamine B (RhB) dyes as single and multicomponent systems in natural sunlight. Characterization of the structure and morphology of the synthesized nanocomposite using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) combined with energy dispersive X-ray spectroscopy (EDS), and photoluminescence (PL) spectroscopy confirmed the formation of Zn₂SnO₄/SnO₂ and heterojunctions between Zn₂SnO₄ and the SnO₂ nanoparticles. A photodegradation efficiency of 99.1% was achieved in 120 min with 50 mg of the photocatalyst for the degradation of MB and 70.6% for the degradation of RhB under the same conditions. In the multicomponent system, the degradation efficiency of 97.9% for MB and 53.2% for RhB was obtained with only 15 mg of the photocatalyst. The degradation of MB occurred through N-demethylation and the formation of azure intermediates and degradation of RhB occurred through sequential deethylation and fragmentation of the xanthene ring, both in single and multicomponent systems. Full article

The use of semiconductors for photocatalytic degradation of organic pollutants has garnered considerable attention as a promising solution to environmental challenges. Compared to TiO₂, BiPO₄ exhibits superior photocatalytic activity. However, its large band gap restricts its light absorption to the UV region. One effective technique for extending BiPO₄’s absorption wavelength into the visible spectrum is the construction of the heterostructure. This study aimed to synthesize monodisperse BiPO₄ nanorods via a solvothermal approach and fabricate BiPO₄/g-C₃N₄ heterojunctions with varying loadings through in situ deposition. Tetracyclines were employed as the target pollutant to evaluate the photocatalytic performance and stability of the prepared materials. The results indicated that 5 wt% of composite exhibited better photocatalytic performance than single catalysts, which showed the highest photodegradation efficiency of approximately 98% for tetracyclines. The prepared bi-photocatalyst presented favorable stability under sunlight irradiation, the photocatalytic activity of which remained almost unchanged after four cycles. The enhanced photocatalytic activity was attributed to the synergistic effect. Additionally, the possible degradation mechanism was elucidated utilizing the semiconductor energy band theory. Overall, this work presents new perspectives on synthesizing innovative and efficient visible-light-driven photocatalysts. It also offers a mechanistic analysis approach by integrating theoretical calculations with experimental observations. Full article

Free-standing copper oxide (Cu₂O)-copper hydroxide (Cu(OH)₂) nanocomposites with enhanced catalytic and antibacterial functionalities were synthesized on copper mesh using a green method based on spinach leaf extract and glycerol. EDX, SEM, and TEM analyses confirmed the chemical composition and morphology. The resulting Cu2O-Cu(OH)₂@Cu mesh exhibited notable hydrophobicity, achieving a contact angle of 137.5° ± 0.6, and demonstrated the ability to separate thick oils, such as HD-40 engine oil, from water with a 90% separation efficiency. Concurrently, its photocatalytic performance was evaluated by the degradation of methylene blue (MB) under a weak light intensity of 5 mW/cm², achieving 85.5% degradation within 30 min. Although its application as a functional membrane in water treatment may raise safety concerns, the mesh showed significant antibacterial activity against both Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria under both dark and light conditions. Using the disk diffusion method, strong bacterial inhibition was observed after 24 h of exposure in the dark. Upon visible light irradiation, bactericidal efficiency was further enhanced—by 17% for S. aureus and 2% for E. coli. These findings highlight the potential of the Cu₂O-Cu(OH)₂@Cu microfibers as a multifunctional membrane for industrial wastewater treatment, capable of simultaneously removing oil, degrading organic dyes, and inactivating pathogenic bacteria through photo-assisted processes. Full article

In this study, the surface photocatalytic activity of an anatase–titanium oxide (TiO_x) film was modified by a thin copper (Cu) layer with the subsequential oxidation annealing process. Through this simple annealing process, the photocatalytic activity of the TiO_x/Cu structure to decompose the methylene blue solution and inhibit the growth of Escherichia coli. could be optimized. With the help of a study on the conductive type required for the oxidation of a single Cu layer, an n/p nanocomposite heterojunction was realized, as this contact system anneals at temperatures of 350 °C and 450 °C. An extra electrical field at the contact interfaces that was be beneficial for separating the photo-generated electron–hole pairs (EHPs) under UV light irradiation was built. The built-in electrical field led to an increase in the structural photocatalytic activity. Moreover, as the p-type cuprous oxide (p-Cu₂O) structure oxidized by the annealed Cu layer could provide a high conduction band that is offset when in contact with the TiO_x film, the photogenerated EHPs on the TiO_x surface could be separated more effectively. Accordingly, the 350 °C-annealed sample, abundant in the nanocomposite TiO_x/Cu₂O heterojunction which could significantly retard the recombination of photo-generated carriers, corresponded to an increase of about 38% in the photocatalytic activity as compared with the single TiO_x film. Full article

Microplastics have emerged as pervasive contaminants in various ecosystems, raising considerable concerns regarding their impact on environmental health and public safety. The degradation of microplastics is thus recognized as a pressing global challenge. Photocatalytic degradation has emerged as a promising approach due to its potential for efficiency and environmental sustainability. Nevertheless, there remains a need to investigate emerging trends and advancements to understand and fully optimize this technique. Consequently, PRISMA guidelines were employed to define the search parameters, enable the identification of pertinent scholarly articles, and systematically gather bibliographic data from the published literature from 2005 to October 2024. A bibliometric analysis of 204 research articles derived from merged Scopus and Web of Science datasets was conducted to map the field’s research landscape. The analysis showed a robust annual publication growth rate of 17.94%, with leading contributions from China, India, Mexico, and the United Kingdom. Keyword analysis revealed that the commonly applied photocatalysts are titanium dioxide and zinc oxide in the photocatalytic degradation of polyethylene terephthalate, polypropylene, polystyrene, polyvinyl chloride, high-density polyethylene, and low-density polyethylene. Advances in collaboration across Asia and Europe have bolstered the research landscape. However, challenges persist in achieving cost-effective scalability, ensuring the safety of degradation byproducts, and translating laboratory findings into real-world applications. Emerging trends include the development of visible-light-responsive catalysts, advanced nanocomposites, and sustainable photocatalytic technologies. This study underscores the utility of bibliometric tools in identifying knowledge gaps and guiding the development of innovative approaches for microplastic degradation as part of environmental remediation efforts. Full article

Nowadays, there is an urgent need for efficient photocatalysts and adsorbents for environmentally relevant applications. This study investigates the effect of polyaniline (PANI) on the structure and performance of carbonized nanocomposites composed of PANI and TiO₂ nanotubes (NTs), focusing on their photocatalytic degradation efficiency and dye adsorption capacity. The hypothesis was that PANI forms conductive carbon domains and stabilizes the anatase phase during thermal treatment, enhancing the performance of TiO₂-NTs as photocatalysts. Nanocomposites based on PANI and TiO₂-NTs (TTP) were synthesized through chemical oxidative polymerization of aniline (ANI) in the presence of TiO₂-NTs using two TiO₂/ANI molar ratios of 50 and 150 and subsequently carbonized at 650 °C, yielding CTTP-50 and CTTP-150. The novel CTTP composites and carbonized pristine TiO₂-NTs (CTNT) were characterized by various techniques, including TEM, UV-Vis diffuse reflectance, Raman spectroscopy, XRD, and TGA. Their performance regarding dye adsorption and photocatalytic degradation under visible light was evaluated with Acid Orange 7, Methylene Blue, and Rhodamine B. CTTP-150 exhibited the highest adsorption capacity and photodegradation rate, attributed to the synergistic effect of PANI, which stabilizes the TiO₂ phase and enhances visible-light absorption and adsorption. Full article

The development of high-performance photocatalysts is vital for combating water pollution and microbial contamination. In this study, visible-light-active Z-scheme heterojunction nanocomposites composed of Co₃O₄ and Nb₂O₅ (CNNC) were synthesized via co-crystallization and subsequent high-pressure annealing to enhance photocatalytic and antimicrobial performance. Structural and optical analyses via XRD, FESEM, TEM, XPS, and PL confirmed the heterojunction formation between porous Co₃O₄ nanoparticles (CONP) and columnar orthorhombic Nb₂O₅ nanoparticles (NONP). The CNNC exhibited significantly improved photocatalytic activity, achieving degradation efficiencies of 95.1% for methylene blue, 72.6% for tetracycline, and 90.0% for Congo red within 150 min. Kinetic studies showed that CNNC’s rate constants were 367% and 466% of those of CONP and NONP, respectively. Moreover, CNNC demonstrated a strong antibacterial effect on Staphylococcus aureus and Escherichia coli with ZOI values of 9.3 mm and 6.8 mm, respectively. Mechanistic analysis revealed that the Z-scheme charge-transfer pathway improved charge separation and reduced electron–hole recombination, contributing to the promoted photocatalytic efficiency. The nanocomposite also showed robust stability and recyclability over five times. These results highlight the promise of CNNC as a bifunctional, visible-light-driven photocatalyst for pollutant decomposition and microbial control. Full article

The growing presence of hazardous organic pollutants in wastewater poses severe environmental and health risks, necessitating sustainable and efficient treatment solutions. Traditional remediation methods have limitations, highlighting the need for innovative approaches. A green synthesis method was developed to produce TiO₂-CeO₂ nanocomposites using Cleistocalyx operculatus leaf extract. The photocatalytic efficiency of the synthesized nanocomposites was evaluated under simulated sunlight by degrading Methylene Blue (MB) dye. Various compositions were tested to determine the optimal performance. The 0.1% TiO₂-CeO₂ nanocomposite achieved the highest degradation efficiency (95.06% in 150 min) with a reaction rate constant (k) of 18.5 × 10⁻² min⁻¹, outperforming commercial TiO₂ (P25, 74.85%, k ≈ 3.7 × 10⁻² min⁻¹). Additionally, the material maintained excellent stability over eight consecutive cycles with only a slight decrease in efficiency from 95.85% to 93.28%. The enhanced photocatalytic activity is attributed to the synergistic effects of CeO₂ incorporation, which enhances charge separation, extends visible light absorption, and promotes reactive oxygen species (ROS) generation. These findings highlight the potential of green-synthesized TiO₂-CeO₂ nanocomposites as a cost-effective and sustainable solution for wastewater treatment. Full article

Efficient photocatalysts based on composite materials are essential for addressing environmental pollution and enhancing water purification. This study presents a novel BiOI/V₂O₅ nanocomposite (BVNC) with a flower-like layered structure, synthesized via a low-temperature solvothermal process followed by high-pressure annealing for visible light (VL)-driven dye degradation and antibacterial activities. Compared to individual BiOI nanoparticles (BOINP) and V₂O₅ nanoparticles (VONP), under VL, the BVNC demonstrated significantly enhanced photocatalytic and antibacterial activity. The best-performing BVNC achieved a remarkable methylene blue degradation efficiency of 95.7% within 140 min, with a rate constant value 439% and 430% of those of BOINP and VONP, respectively. Additionally, BVNC exhibited high photocatalytic efficiencies for rhodamine 6G (94.0%), methyl orange (90.4%), and bisphenol A (69.5%) over 160 min, highlighting the superior performance of the composite materials for cationic and anionic dyes. Furthermore, BVNC established outstanding antibacterial capability against Staphylococcus aureus and Escherichia coli, demonstrating zones of inhibition of 12.24 and 11.62 mm, respectively. The improved catalytic and antibacterial capability is ascribed to the presence of a robust p-n heterojunction between BOINP and VONP, which broadens the photo-absorption range, reduces bandgap energy, and facilitates the significant separation of excitons and faster release of reactive oxygen species. Full article

The design of efficient and stable visible-light-driven photocatalysts is paramount for sustainable hydrogen (H₂) evolution and the degradation of organophosphorus pesticides, exemplified by dichlorvos (DDVP). In this work, we synthesized a co-catalyst-free nanocomposite photocatalyst composed of Al₆Si₂O₁₃ (ASO) and Cd_8.05Zn_1.95S₁₀ (ZCS). By constructing a Type-I heterojunction, the optimized ASO/ZCS-1 nanocomposite (ASO loading ratio: 30%) enhanced visible-light-driven H₂ evolution activity (5.1 mmol g⁻¹ h⁻¹), nearly doubling that of pristine ZCS (2.7 mmol g⁻¹ h⁻¹). Stability assessments revealed catalytic durability for ASO/ZCS-1 over five successive cycles, whereas the activity of pure ZCS precipitously declined to 59.7% of its initial level. Additionally, ASO, ZCS, and ASO/ZCS-2 (ASO loading ratio: 50%) demonstrated notable photocatalytic efficiency toward DDVP degradation without any co-catalyst, reducing DDVP concentration to 56.2% (ASO), 18.9% (ASO/ZCS-2), and 38.4% (ZCS), with corresponding degradation stability of 93.8%, 95.1%, and 93.8%, respectively. These results underscore the superior photocatalytic activity and stability of ASO, ZCS, and ASO/ZCS in the remediation of organophosphorus pesticides, with the Type-I heterojunction structure of ASO/ZCS enhancing both degradation activity and stability. Comprehensive characterizations by X-ray photoelectron spectroscopy (XPS), ultraviolet–visible diffuse reflectance spectroscopy (UV–vis DRS), and differential charge density analyses verified the Type-I heterojunction charge-transfer mechanism, effectively suppressing charge recombination and thus improving photocatalytic performance. Consequently, ASO/ZCS nanocomposites exhibit significant promise for broad applications in sustainable H₂ production, pollutant degradation, and ensuring food and agricultural product safety. Full article

The widespread presence of pesticides—especially malathion—in aquatic environments presents a major obstacle to conventional remediation strategies, while the ongoing global energy crisis underscores the urgency of developing renewable energy sources such as hydrogen. In this context, photocatalytic water splitting emerges as a promising approach, though its practical application remains limited by poor charge carrier dynamics and insufficient visible-light utilization. Herein, we report the design and evaluation of a series of TiO₂-based ternary nanocomposites comprising commercial P25 TiO₂, reduced graphene oxide (rGO), and molybdenum disulfide (MoS₂), with MoS₂ loadings ranging from 1% to 10% by weight. The photocatalysts were fabricated via a two-step method: hydrothermal integration of rGO into P25 followed by solution-phase self-assembly of exfoliated MoS₂ nanosheets. The composites were systematically characterized using X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. Photocatalytic activity was assessed through two key applications: the degradation of malathion (20 mg/L) under simulated solar irradiation and hydrogen evolution from water in the presence of sacrificial agents. Quantification was performed using UV-Vis spectroscopy, gas chromatography–mass spectrometry (GC-MS), and thermal conductivity detection (GC-TCD). Results showed that the integration of rGO significantly enhanced surface area and charge mobility, while MoS₂ served as an effective co-catalyst, promoting interfacial charge separation and acting as an active site for hydrogen evolution. Nearly complete malathion degradation (~100%) was achieved within two hours, and hydrogen production reached up to 6000 µmol g⁻¹ h⁻¹ under optimal MoS₂ loading. Notably, photocatalytic performance declined with higher MoS₂ content due to recombination effects. Overall, this work demonstrates the synergistic enhancement provided by rGO and MoS₂ in a stable P25-based system and underscores the viability of such ternary nanocomposites for addressing both environmental remediation and sustainable energy conversion challenges. Full article

Since the publication of the 12 principles of green chemistry in 1998 by Paul Anastas and John Warner, the green synthesis of metal and metal oxide nanoparticles has emerged as an eco-friendly and sustainable alternative to conventional chemical methods. Plant-based synthesis utilizes natural extracts as reducing and stabilizing agents, minimizing harmful chemicals and toxic by-products. Ag nanoparticles (Ag-NPs) exhibit strong antibacterial activity; Au nanoparticles (Au-NPs) are seen as a promising carrier for drug delivery and diagnostics because of their easy functionalization and biocompatibility; and ZnO nanoparticles (ZnO-NPs), on the other hand, produce reactive oxygen species (ROS) that kill microorganisms effectively. These nanoparticles also demonstrate antioxidant properties by scavenging free radicals, reducing oxidative stress, and preventing degenerative diseases. Green syntheses based on plant extracts enhance biocompatibility and therapeutic efficacy, making them suitable for antimicrobial, anticancer, and antioxidant applications. Applying a similar “green synthesis” for advanced nanostructures like graphitic carbon nitride (GCN) is an environmentally friendly alternative to the traditional ways of doing things. GCN exhibits exceptional photocatalytic activity, pollutant degradation efficiency, and electronic properties, with applications in environmental remediation, energy storage, and biomedicine. This review highlights the potential of green-synthesized hybrid nanocomposites combining nanoparticles and GCN as sustainable solutions for biomedical and environmental challenges. The review also highlights the need for the creation of a database using a machine learning process that will enable providing a clear vision of all the progress accomplished till now and identify the most promising plant extracts that should be used for targeted applications. Full article