Search Results (139)

The overtopping-induced lateral erosion breaching of tailings dams represents a critical disaster mechanism threatening structural safety, particularly in reinforced fine-grained tailings dams where erosion behaviors demonstrate pronounced water–soil coupling characteristics and material anisotropy. Through physical model tests and numerical simulations, this study systematically investigates lateral erosion failure patterns of reinforced fine-grained tailings under overtopping flow conditions. Utilizing a self-developed hydraulic initiation test apparatus, with aperture sizes of reinforced geogrids (2–3 mm) and flow rates (4–16 cm/s) as key control variables, the research elucidates the interaction mechanisms of “hydraulic scouring-particle migration-geogrid anti-sliding” during lateral erosion processes. The study revealed that compared to unreinforced specimens, reinforced specimens with varying aperture sizes (2–3 mm) demonstrated systematic reductions in final lateral erosion depths across flow rates (4–16 cm/s): 3.3–5.8 mm (15.6−27.4% reduction), 3.1–7.2 mm (12.8–29.6% reduction), 2.3–11 mm (6.9–32.8% reduction), and 2.5–11.4 mm (6.2–28.2% reduction). Smaller-aperture geogrids (2 mm × 2 mm) significantly enhanced anti-erosion performance through superior particle migration inhibition. Concurrently, a pronounced positive correlation between flow rate and lateral erosion depth was confirmed, where increased flow rates weakened particle erosion resistance and exacerbated lateral erosion severity. The numerical simulation results are in basic agreement with the lateral erosion failure process observed in model tests, revealing the dynamic process of lateral erosion in the overtopping breach of a reinforced tailings dam. These findings provide critical theoretical foundations for optimizing reinforced tailings dam design, construction quality control, and operational maintenance, while offering substantial engineering applications for advancing green mine construction. Full article

As sea levels rise and extreme weather events become more frequent due to climate change, coastal urban areas are increasingly vulnerable to wave overtopping and flooding. Retrofitting existing vertical seawalls with retreated storm walls represents a key adaptive strategy, especially in the Mediterranean, where steep foreshores and limited public space constrain conventional coastal defenses. This study investigates the effectiveness of storm walls in reducing wave overtopping on vertical walls with steep foreshores (1:7 to 1:10) through high-fidelity numerical simulations using the SWASH model. A comprehensive parametric study, involving 450 test cases, was conducted using Latin Hypercube Sampling to explore the influence of geometric and hydrodynamic variables on overtopping rate. Model validation against Eurotop/CLASH physical data demonstrated strong agreement (r = 0.96), confirming the reliability of SWASH for such applications. Key findings indicate that longer promenades (Gc) and reduced impulsiveness of the wave conditions reduce overtopping. A new empirical reduction factor, calibrated for integration into the Eurotop overtopping equation for plain vertical walls, is proposed based on dimensionless promenade width and water depth. The modified empirical model shows strong predictive performance (r = 0.94) against SWASH-calculated overtopping rates. This work highlights the practical value of integrating storm walls into urban seawall design and offers engineers a validated tool for enhancing coastal resilience. Future research should extend the framework to other superstructure adaptations, such as parapets or stilling basins, to further improve flood protection in the face of climate change. Full article

Standalone tsunami defense structures have demonstrated limitations in mitigating wave energy during the 2011 Japan tsunami. In order to mitigate future tsunamis in Japan, multi-layered protective mechanisms have been suggested or implemented after the incident. These include heightening the destroyed or existing embankment with concrete or stones, protecting embankments with concrete blocks, compacting the landward soil, elevating the ground following the coastal embankment, and incorporating green belts. Despite extensive research on the mitigation effects of such multiple countermeasures, the optimal structural configuration remains uncertain. In this study, we evaluated the performance of a multiple mitigation system consisting of a landward forest (F) on an elevated mound (M) following a seaward embankment (E) under a range of supercritical flow conditions using a flume experiment. Several mound heights and lengths were selected to determine the optimum mound for installing the forest. The combination of E and F of 12 rows of trees on M with a minimum height of 1.8 cm (Case EMF_R12) created the greatest water cushion depth between E and M. When M was positioned without F, the water cushion between E and M was created by raising the height of the mound rather than its length. Conversely, a mound with a minimum height and length with a forest was found to be effective in creating the largest water cushion and maximum reduction of the flow energy. The highest energy reduction was between 45 and 70% in this experiment. These findings provide useful insights for developing multiple tsunami mitigation strategies that combine artificial and natural approaches. Full article

This study presents a flood risk assessment of five rural bridges along the monsoon-prone Khar–Mohmand Gat corridor in Northwestern Pakistan using an integrated hydrologic and hydraulic modeling framework. Hydrologic simulations for 50- and 100-year design storms were performed using the Hydrologic Engineering Center’s Hydrologic Modeling System (HEC-HMS), with watershed delineation conducted via Geographic Information Systems (GIS). Calibration was based on regional rainfall data from the Peshawar station using a Soil Conservation Service Curve Number (SCS-CN) of 86 and time of concentration calculated using Kirpich’s method. The resulting hydrographs were used in two-dimensional hydraulic simulations using the Hydrologic Engineering Center’s River Analysis System (HEC-RAS) to evaluate water surface elevations, flow velocities, and Froude numbers at each bridge site. The findings reveal that all bridges can convey peak flows without overtopping under current climatic conditions. However, Bridges 3 to 5 experience near-critical to supercritical flow conditions, with velocities ranging from 3.43 to 4.75 m/s and Froude numbers between 0.92 and 1.04, indicating high vulnerability to local scour. Bridge 2 shows moderate risk, while Bridge 1 faces the least hydraulic stress. The applied modeling framework effectively identifies structures requiring priority intervention and demonstrates a practical methodology for assessing flood risk in ungauged, data-scarce, and semi-arid regions. Full article

For the safety assessment of concrete dam–foundation systems, this study used an explicit time-stepping small-displacement algorithm, which simulates the hydromechanical interaction and considers the discrete representation of the foundation discontinuities. The proposed innovative methodology allows for the definition of more reliable safety factors and the identification of more realistic failure modes by integrating (i) softening-based constitutive laws that are closer to the real behavior identified experimentally in concrete–concrete and concrete–rock interfaces; (ii) a water height increase that can be considered in both hydraulic and mechanical models; and (iii) fracture propagation along the dam–foundation interface. Parametric studies were conducted to assess the impact of the mechanical properties on the global safety factors of three gravity dams with different heights. The results obtained using a coupled/fracture propagation model were compared with those from the strength reduction method and the overtopping scenario not considering the hydraulic pressure increase. The results show that the safety assessment should be conducted using the proposed methodology. It is shown that the concrete–rock interface should preferably have a high value of fracture energy or, ideally, higher tensile and cohesion strengths and high associated fracture energy. The results also indicate that with a brittle concrete–rock model, the predicted safety factors are always conservative when compared with those that consider the fracture energy. Full article

The breaching of embankments have devastating consequences for the economic, human, cultural, and environmental assets. One of the most widely used approaches for understanding the characteristics of embankment breaching is through laboratory and field-scale experiments. Despite the advancements in instrumentation and measurement techniques of embankment breaching experiments, there is a lack of comprehensive documentation. In this review, the advancements and state-of-the-art instrumentation and measurement techniques employed in overtopping-induced embankment breaching of laboratory and field-scale experiments are discussed. The key parameters commonly measured in experimental modeling are breach morphological changes, reservoir and flow depth, velocity, breach outflow, and pore water pressure. Instrumentation for breach morphological change detection, including mechanical, photography, photogrammetry, electronic sensors, and laser technologies, are reviewed. The various flow velocity measuring techniques, such as Particle Tracking Velocimetry (PTV), Particle Imaging Velocimetry (PIV), acoustic, and radar-based techniques, are discussed. Instrumentation for water level, flow rate, and pore pressure measurements are also briefly documented. The challenges and constraints encountered during embankment breaching experiments are discussed. The review further suggests future perspectives in improving the accuracy of breach detection, velocity, and pore pressure measurement techniques. Additionally, improving scale effects by incorporating geotechnical factors is also recommended. Full article

Wave energy is an increasingly attractive renewable energy source due to its potential and predictability. Various Wave Energy Converters (WECs) have been developed, including attenuators, overtopping devices, and point absorbers. The Wave Dragon, an overtopping device, is a floating structure anchored to the seabed with a mooring system. It uses two reflectors to guide incoming waves into a central reservoir, where the captured water flows through turbines to generate electricity. This study enhances the realism of Wave Dragon simulations by modeling it as a moving structure with moorings, addressing key gaps in prior research. Real-time wave data from the Caspian Sea, collected over a year, were used to develop a 3D model and analyze the device’s performance under varying wave conditions. Four significant wave heights (Hs) of 1.5, 2.5, 3.5, and 4.5 m were tested. The results demonstrate that higher wave heights increase water flow through the turbines, leading to higher energy output, with monthly energy generation recorded as 16.03, 25.95, 31.45, and 56.5 MWh for the respective wave heights. The analysis also revealed that higher wave heights significantly increase pressure forces on the Wave Dragon, from 2.97 × 10⁵ N at 1.5 m to 1.95 × 10⁶ N at 4.5 m, representing a 6.5-fold increase. These findings underscore the potential of Wave Dragons to enhance renewable energy production while ensuring structural robustness in varying wave conditions. Full article

Among the various potential renewable energy sources, sea waves offer significant potential, which can be harnessed using wave energy converter (WEC) devices such as overtopping converters. These devices operate by directing incident waves up a ramp into a reservoir. The water then passes through a turbine coupled with an electrical generator before returning to the ocean. Thus, the present study deals with the geometrical evaluation of an overtopping WEC, where the influence of the ratio between the height and length of the device ramp ($H_1/L_1$) on the amount of water mass (M) that enters the reservoir was investigated. Numerical simulations were performed using ANSYS-Fluent software, 22 R1 version, to generate and propagate realistic irregular (RI) waves and representative regular (RR) waves found in the coastal region of the municipality of Rio Grande, in the state of Rio Grande do Sul, southern Brazil. Consequently, through constructal design, the optimal WEC geometry for both wave approaches were identified as the same, where (${H_1/L_1)}_o=0.30$. Thus, considering the RI waves, $M=$ 200,820.77 kg was obtained, while, considering the RR waves, $M=$ 144,054.72 kg was obtained. Full article

Forecasting flood characteristics (e.g., water levels and velocity) is a growing concern due to climate change. It is therefore necessary to consider the stability conditions of earthen levees used to mitigate floods during a flood risk assessment. This technical note presents a method to assess probabilistic flood hazard that takes into account levee failures, for a levee located along Etobicoke Creek in Toronto, Canada. We compute flood scenario probabilities resulting from multiple flood scenarios that accounts for both the levee failures across the length of the levee, and different levee-failure mechanisms (e.g., backward erosion and overtopping). Then, for each location of the flooded area, we compute a cumulative flood exceedance probability curve for flood depth and velocity. This method provides a flood-hazard map (depth and velocity) for a given probability and probabilistic maps for given values of depth or velocity. Full article

Recent increases in rainfall duration and intensity due to climate change have heightened the importance of levee stability. However, previous studies on levee failure, primarily caused by seepage and overtopping, have mostly examined these causes independently owing to their distinct characteristics. In this study, we conducted lateral overtopping failure experiments under seepage conditions that closely resembled those in experiments conducted in previous studies. Seepage was monitored using water pressure sensors and a distributed optical fiber cable that provided continuous heat for temperature monitoring in the levee. Τhe analysis of levee failure due to lateral overtopping, in the presence of seepage, was conducted using image analysis with digitization techniques and machine learning-based color segmentation techniques on the protected lowland side of the levee, targeting the same area. The results revealed that levee failure occurred more than twice as fast in experiments where seepage conditions were considered compared to the experiments where they were not. Thus, levees weakened by seepage are more vulnerable to overtopping and breaching. Consequently, employing a comprehensive approach that integrates various monitoring and analysis methods for assessing levee stability is preferable to relying on a single method alone. Full article

As part of an investigation into downfall impacts from violent overtopping waves, experimental data are presented for the impact pressures and forces generated by regular and focused waves breaking onto a vertical wall and impacting a landward horizontal deck at a scale of 1:38. Particular attention is given to the wave-by-wave uprush and impact downfall events. By selecting regular and focused wave conditions that produce impacts, new trends are identified for violent downfall phenomena that could easily be underestimated in current practice. The characteristics of the downfall impacts are investigated and three different types of downfall impact are identified and discussed. Using a Wavelet Filter to denoise the signal from pressure probes without losing the peak impact pressures or introducing a phase shift, the distinctive features and dynamic behaviours of the white-water impacts are considered, and it is shown that downfall pressure magnitudes of $30–40 \rho gH$ are regularly achieved. Dynamic impulse times of the events are also presented with higher-impact events generally relating to shorter impulse times, highlighting the dynamic character of these impacts. The largest downfall pressures are found to occur further from the vertical wall than previously measured. Importantly, the spray travelling furthest from the point of the initial wave impact on the vertical wall causes some of the largest downfall pressures on the deck. The paper concludes that, while the dataset is small, there are strong indications that the effects of these types of impacts are structurally significant and present a risk to infrastructure located landward of seawalls. Full article

In recent years, reservoir flood control and dam safety have faced severe challenges due to changing environmental conditions and intense human activities. There has been a significant increase in the proportion of dam breaks caused by floods exceeding reservoir design levels. Dam breaks have periodically occurred due to flood overtopping, threatening people’s lives and properties. This highlights the importance of describing the challenges encountered in reservoir flood risk prevention and control under extreme climatic conditions and proposing strategies to safeguard reservoirs against floods and to protect downstream communities. This study conducts a statistical analysis of dam breaks resulting from floods exceeding reservoir design levels, revealing new risk indicators in these settings. The study examines recent representative engineering cases involving flood risks and reviews research findings pertaining to reservoir flood risks under extreme climatic conditions. By comparing flood prevention standards at typical reservoirs and investigating the problems and challenges associated with current standards, the study presents the challenges and strategies associated with managing flood risks in reservoirs under extreme climatic conditions. The findings show that the driving forces and their effects shaping flood risk characteristics in specific regions are influenced by atmospheric circulation and vegetative changes in underlying surfaces or land use. There is a clear increasing probability of dam breaks or accidents caused by floods exceeding design levels. Most dam breaks or accidents occur in small and medium-sized reservoirs, due to low flood control standards and poor management. Therefore, this paper recommends measures for improving the flood prevention capacity of these specific types of reservoirs. This paper proposes key measures to cope with floods exceeding reservoir design levels, to supplement the existing standard system. This includes implementing an improved flood standard based on dam risk level and the rapid reduction in the reservoir water level. To prevent breaks associated with overtopping, earth–rock dams should be designed to consider extreme rainfall events. More clarity is needed in the execution principles of flood prevention standards, and the effectiveness of flood calculations should be studied, adjusted, and validated. The research results provide better descriptions of flood risks in reservoirs under extreme climatic conditions, and the proposed strategies have both theoretical and practical implications for building resilience against flood risks and protecting people’s lives and properties. Full article

It is crucial for reef revetments to respond dynamically to rigorous wave actions for structural stability and safety. A comprehensive analysis of the interaction between the wave force and wave overtopping in a reef revetment project was conducted based on wave flume experiments. This study explored how wave conditions, the water depth along the reef flat, and the proximity of the reef edge to the revetment project influenced wave overtopping and wave force patterns. The results indicate that as the incident wave height, period, and water depth along the reef flat increased, the average wave overtopping within the revetment project also increased. Additionally, higher levels of average wave overtopping occurred with the decrease in the distance between the revetment project and the reef edge. The peak wave force on the seawall of the revetment project was studied in response to various factors, including wave period, wave height, water depth along the reef flat, and distance to the reef edge. The changes in the maximum wave force reflected those of the average wave overtopping, with a strong linear correlation. The quantitative relationship between these variables was determined, and the wave forces on the seawall could be indirectly estimated using the average wave overtopping volume. This study provides an efficient methodology for assessing the dynamic attributes of revetment projects and the disaster risk of these structures. Full article

A thorough literature review was conducted on the effects of free surface oscillation in open channels, highlighting the risks of the occurrence of positive and negative surge waves that can lead to overtopping. Experimental analyses were developed to focus on the instability of the flow due to constrictions, gate blockages, and the start-up and shutdown of hydropower plants. A forebay at the downstream end of a tunnel or canal provides the right conditions for the penstock inlet and regulates the temporary demand of the turbines. In tests with a flow of 60 to 100 m³/h, the effects of a gradually and rapidly varying flow in the free surface profile were analyzed. The specific energy and total momentum are used in the mathematical characterization of the boundaries along the free surface water profile. A sudden turbine stoppage or a sudden gate or valve closure can lead to hydraulic drilling and overtopping of the infrastructure wall. At the same time, a PID controller, if programmed appropriately, can reduce flooding by 20–40%. Flooding is limited to 0.8 m from an initial amplitude of 2 m, with a dissipation wave time of between 25 and 5 s, depending on the flow conditions and the parameters of the PID characteristics. Full article

In order to develop green energy, reduce carbon emissions, and alleviate global warming and the green energy crisis, many researchers focus on wave energy, using a device to convert wave energy into electricity. The three main types of wave energy converters are the overtopping type, the oscillating water column type, and the oscillating body type, and for most of them, the power generation efficiency is low. The research team in this paper proposed a wave energy converter for a wave-induced oscillation heave plate. The plate vibrates up and down under the action of waves, and the captured energy of the vibrating plate transfers the energy to the generator, so as to generate electricity. There is electricity only when there is vibration; therefore, the vibration characteristic of the converter is crucial to power generation. So, the vibration characteristics of the energy capture structure of the converter were studied experimentally. The test results show that the energy harvesting device can vibrate, and the vibration effect is good, which further indicates that the device can generate electricity. The effects of different wave conditions and system stiffnesses on amplitude and corresponding amplitude were studied, and the amplitude increases with the increase in wave height and period and decreases with the increase in system stiffness. The amplitude response decreases with the increase in wave height and system stiffness. Under the test conditions, the maximum amplitude of the system is 6.23 cm (when the wave period is 1.40 s, the wave height is 0.25 m, and the system stiffness is 1735.62 N/m), and the maximum amplitude ratio is 0.34 (when the wave period is 1.1 s, the wave height is 0.10 m, and the system stiffness is 1735.62 N/m). Full article