Search Results (19)

A wide band range can cover more of the characteristic spectral lines of substances, and thus analyze the structure and composition of substances more accurately. In order to broaden the band range of spectral instruments, an ultra-wide-band Fourier transform infrared spectrometer is designed. The incident light of the spectrometer is constrained by a secondary imaging scheme, and switchable light sources and detectors are set to achieve an ultra-wide band coverage. A compact and highly stable double-moving mirror swing interferometer is adopted to generate optical path difference, and a controller is used to stabilize the swing of the moving mirrors. A distributed design of digital system integration and analog system integration is adopted to achieve a lightweight and low-power-consumption spectrometer. High-speed data acquisition and a transmission interface are applied to improve the real-time performance. Further, a series of experiments are performed to test the performance of the spectrometer. Finally, the experimental results show that the spectral range of the ultra-wide-band Fourier transform infrared spectrometer covers 0.770–200 μm, with an accurate wave number, a spectral resolution of 0.25 cm⁻¹, and a signal-to-noise ratio better than 50,000:1. Full article

Spatial heterodyne spectroscopy (SHS) based on prism dispersion is a novel technique designed to overcome the limitations of traditional grating-based SHS, which is affected by grating diffraction. However, there are still some challenges with this technique, one of which is that the fringe localization plane (FLP) moves with changes in wavelength. This paper proposes a prism-based tunable SHS where the FLP is fixed, utilizing prism–bimirror–mirror structures. The theoretical spectral resolving power, based on an example, is higher than 1300 in the spectral range from 10,000 cm⁻¹ to 25,641 cm⁻¹ and is approximately 27,595 at 25,641 cm⁻¹. Furthermore, we propose solutions to simplify the motion control system and address the problem of spectral aliasing. Full article

Optical Wireless Communication (OWC) technology has gained significant attention in recent years due to its potential for providing high-data-rate wireless connections through the large license-free bandwidth available. A key challenge in OWC systems, similar to high-frequency Radiofrequency (RF) systems, is the presence of dead zones caused by obstacles like buildings, trees, and moving individuals, which can degrade signal quality or disrupt data transmission. Traditionally, relays have been used to mitigate these issues. Intelligent Reflecting Surfaces (IRSs) have recently emerged as a promising solution, enhancing system performance and flexibility by providing reconfigurable communication channels. This paper presents an overview of the application of IRSs in OWC systems. Specifically, we categorize IRSs into two main types: mirror array-based IRSs and metasurface-based IRSs. Furthermore, we delve into modeling approaches of mirror array-based IRSs in OWC and analyze recent advances in IRS control, which are classified into system power or gain optimization-oriented, system link reliability optimization-oriented, system data rate optimization-oriented, system security optimization-oriented, and system energy optimization-oriented approaches. Moreover, we present the principles of metasurface-based IRSs from a physical mechanism perspective, highlighting their application in OWC systems through the distinct roles of light signal refraction and reflection. Finally, we discuss the key challenges and potential future directions for integrating IRS with OWC systems, providing insights for further research in this promising field. Full article

In this study, a tracking and pointing control system with a dual-FSM (fast steering mirror) two-dimensional flexible turntable composite axis is proposed. It is applied to the target-tracking accuracy control in a GI LiDAR (ghost imaging LiDAR) system. Ghost imaging is a multi-measurement imaging method; the dual-FSM GI LiDAR tracking and pointing imaging control system proposed in this study mainly solves the problems of the high-resolution remote sensing imaging of high-speed moving targets and various nonlinear disturbances when this technology is transformed into practical applications. Addressing the detrimental effects of nonlinear disturbances originating from internal flexible mechanisms and assorted external environmental factors on motion control’s velocity, stability, and tracking accuracy, a nonlinear active disturbance rejection control (NLADRC) method based on artificial neural networks is advanced. Additionally, to overcome the limitations imposed by receiving aperture constraints in GI LiDAR systems, a novel optical path design for the dual-FSM GI LiDAR tracking and imaging system is put forth. The implementation of the described methodologies culminated in the development of a dual-FSM GI LiDAR tracking and imaging system, which, upon thorough experimental validation, demonstrated significant improvements. Notably, it achieved an improvement in the coarse tracking accuracy from 193.29 μrad (3σ) to 87.21 μrad (3σ) and enhanced the tracking accuracy from 10.1 μrad (σ) to 1.5 μrad (σ) under specified operational parameters. Furthermore, the method notably diminished the overshoot during the target capture process from 28.85% to 12.8%, concurrently facilitating clear recognition of the target contour. This research contributes significantly to the advancement of GI LiDAR technology for practical application, showcasing the potential of the proposed control and design strategies in enhancing system performance in the face of complex disturbances. Full article

In order to improve the control of a moving mirror control system and enhance the anti-interference ability of the system, active disturbance rejection control (ADRC) with parameter autotuning is proposed and applied to control a rotary voice coil motor (RVCM). Improved snake optimization (I-SO) was applied to tune and optimize ADRC’s key parameters. To obtain excellent parameters efficiently, in the population initialization phase of SO, the quality and diversity of initial solutions were improved through a chaotic elite opposition learning algorithm. In the local search phase, a sine and cosine (SC) search mode was introduced to enhance the local search ability of SO. The simulation results show that I-SO can effectively find the ideal parameters. I-SO has excellent search capability and stability. The experimental control system of a moving mirror was established, and the effectiveness of the parameters optimized by I-SO was verified. ADRC with parameter autotuning showed excellent control in the moving mirror control system, and the stability of the optical path scanning speed reached 99.2%. Full article

In this work, a closed loop control system is developed to optically localize and track micro-robots with high precision. These micro-robots (i.e., micro-conveyors) are in motion simultaneously across a smart surface.The developed method’s primary objectives are to optimize their trajectories, avoid collisions between them, and control their position with micrometric resolution. This article presents and characterizes the tracking of a single micro-conveyor, and the method works similarly when multiple micro-robots move over the surface. Our tracking method starts with a scanning phase, where a 2D steering mirror, placed above the smart surface, reflects a laser beam toward the conveying surface seeking for the target. Localization occurs when this light beam reaches the micro-conveyor. By adding a retro-reflective element, that reflects the light in the same direction of the the incident light, onto the surface of the micro-conveyor, the light will be reflected towards a photodetector. Depending on the feedback from the photodetector, the steering mirror rotates to track the trajectory of the micro-conveyor. The tip-tilt angular values of the steering mirror allows the micro-conveyor position to be obtained via calibrated localization system. The aim of this work is to regulate the micro-conveyor, within a closed-loop control system, to reduce the positional error between the actual and desired position. The actual position value is measured in real-time application using our developed optical sensor. Results for tracking in the x-and y-axis have validated the proposed method, with an average tracking error less than 30 µm within a range 150 mm × 150 mm. Full article

A moving mirror control system of the Fourier transform spectrometer (FTS) based on the feedforward inputs obtained by the intelligent algorithm is proposed in this paper. Feedforward control is an important part of the moving mirror speed control system of the FTS. And it is always difficult to quantitatively calculate the feedforward inputs through a precise mathematical model of the controlled object. Therefore, based on the expected motion law, an intelligent adaptive algorithm for obtaining feedforward inputs of the moving mirror system was designed. The algorithm decomposed the motion stroke into several position points, iteratively obtained the driving quantity of the moving mirror that met the expected instantaneous speed of each position point, and finally obtained the feedforward inputs of the whole motion stroke. The feedforward inputs obtained by the intelligent algorithm combined with the speed loop PID control constitute the complete moving mirror speed control system. Then, we applied the control system to the moving mirror of the FTS and acquired the velocity of the moving mirror. The experimental results show that the control system is feasible, the error of the peak-to-peak velocity is 0.047, and the error of the root mean square (RMS) velocity is 0.003. Compared with the single-speed-loop control system without feedforward inputs, the error of the peak-to-peak velocity is reduced by 43.3%, and the error of the RMS velocity is reduced by 67.7%, realizing a more accurate control of the moving mirror. Therefore, the control system based on the feedforward inputs obtained by the intelligent algorithm is a feasible and effective moving mirror speed control scheme of the FTS. Full article

An active optical system with three segmented mirrors was proposed to verify the co-focus and co-phase progress. In this system, a kind of large-stroke and high-precision parallel positioning platform was specially developed to help support the mirrors and reduce the error between them, which can move in three degrees of freedom out of plane. The positioning platform was composed of three flexible legs and three capacitive displacement sensors. For the flexible leg, a kind of forward-type amplification mechanism was specially designed to amplify the displacement of the piezoelectric actuator. The output stroke of the flexible leg was no less than 220 μm and the step resolution was up to 10 nm. Further, a linear model was established to identify the amplification ratio between the actuator and the flexible leg, which can increase the precision of the positioning platform. Moreover, three capacitive displacement sensors with a resolution of 2.5 nm were symmetrically installed in the platform to accurately measure the position and attitude of the platform. To improve the stability and precision of the platform, particle swarm optimization algorithm was applied to identify the control matrix, which can help the platform achieve ultra-high precision positioning. The results showed that the theoretical matrix parameters had a maximum deviation of 5.67% from the experimental ones. Finally, abundant experiments verified the excellent and stable performance of the platform. The results proved that while bearing the heavy mirror, which is no more than 5 kg, the platform can realize a 220 μm translation stroke and 2.0 mrad deflection stroke, with a high step resolution of 20 nm and 0.19 μrad. These indicators can perfectly cater to the requirements of the proposed segmented mirror system’s co-focus and co-phase adjustment progress. Full article

The Advanced Virgo Plus project aims to increase the sensitivity of the Virgo gravitational-wave detector, given the forthcoming O4 Observing Run. One of the major upgrades is the addition of the Signal Recycling Mirror in the optical layout. This additional mirror will provide a broadband improvement to the sensitivity curve of the instrument, but poses significant challenges in the acquisition and operation of the detector’s working point. The process which brings the main optical components from the uncontrolled state to the final working point, which ensures the best detector sensitivity, is called lock acquisition: the lock acquisition is made by moving through increasingly more complex configurations toward the full control of all the interferometer’s longitudinal degrees of freedom. This paper will focus on the control of the Dual-Recycled Michelson Interferometer (DRMI, the central part of the Virgo interferometer), presenting a comprehensive study of the optical simulations used in the design and the commissioning of this configuration. Treated topics include: the characterization of optical fields, powers, and error signals for the controls; the development of a trigger logic to be used for the lock acquisition; the study of the alignment sensing and control system. The interdependence between the three items has also been studied. Moreover, the validity of the studied techniques will be assessed by a comparison with experimental data. Full article

In this paper, a tracking and pointing control system with dual-FSM (fast steering mirror) composite axis is proposed. It is applied to the target-tracking accuracy control in a 3D GISC LiDAR (three-dimensional ghost imaging LiDAR via sparsity constraint) system. The tracking and pointing imaging control system of the dual-FSM 3D GISC LiDAR proposed in this paper is a staring imaging method with multiple measurements, which mainly solves the problem of high-resolution remote-sensing imaging of high-speed moving targets when the technology is transformed into practical applications. In the research of this control system, firstly, we propose a method that combines motion decoupling and sensor decoupling to solve the mechanical coupling problem caused by the noncoaxial sensor installation of the FSM. Secondly, we suppress the inherent mechanical resonance of the FSM in the control system. Thirdly, we propose the optical path design of a dual-FSM 3D GISC LiDAR tracking imaging system to solve the problem of receiving aperture constraint. Finally, after sufficient experimental verification, our method is shown to successfully reduce the coupling from 7% to 0.6%, and the precision tracking bandwidth reaches 300 Hz. Moreover, when the distance between the GISC system and the target is 2.74 km and the target flight speed is 7 m/s, the tracking accuracy of the system is improved from 15.7 μrad (σ) to 2.2 μrad (σ), and at the same time, the system recognizes the target contour clearly. Our research is valuable to put the GISC technology into practical applications. Full article

Aiming to address the problem of moving mirror speed fluctuations in moving mirror control systems, an improved active disturbance rejection double closed-loop controller (IADR-DCLC) is proposed and verified by simulation to realize the high-performance control of a moving mirror control system. First, the mathematical model of a rotary-type voice coil motor (RT VCM) is established, and the relationship between the angular velocity of the RT VCM and the optical path scanning velocity is analyzed. Second, in order to suppress the model uncertainty and external disturbance of the system, an improved active disturbance rejection controller (IADRC) is proposed. Compared with a conventional ADRC, the tracking differentiator of the proposed IADRC is replaced with desired signal optimization (DSO), and the actual speed is introduced to the extended state observer (ESO). The IADRC is used in the position–speed double closed-loop control model. Finally, the simulation results show that the IADR-DCLC has not only a good tracking effect but also a good anti-interference ability and can meet the requirements of the moving mirror control system for the uniformity of optical-path scanning speed and accurate control of the position of the moving mirror. Full article

Temporal modulation of the quantum vacuum through fast motion of a neutral body or fast changes of its optical properties is known to promote virtual into real photons, the so-called dynamical Casimir effect. Empowering modulation protocols with spatial control could enable the shaping of spectral, spatial, spin, and entanglement properties of the emitted photon pairs. Space–time quantum metasurfaces have been proposed as a platform to realize this physics via modulation of their optical properties. Here, we report the mechanical analog of this phenomenon by considering systems in which the lattice structure undergoes modulation in space and in time. We develop a microscopic theory that applies both to moving mirrors with a modulated surface profile and atomic array meta-mirrors with perturbed lattice configuration. Spatiotemporal modulation enables motion-induced generation of co- and cross-polarized photon pairs that feature frequency-linear momentum entanglement as well as vortex photon pairs featuring frequency-angular momentum entanglement. The proposed space–time dynamical Casimir effect can be interpreted as induced dynamical asymmetry in the quantum vacuum. Full article

In this paper, methods are presented for designing a quadrotor attitude control system with disturbance rejection ability, wherein only one parameter needs to be tuned for each axis. The core difference between quadrotor platforms are extracted as critical gain parameters (CGPs). Reinforcement learning (RL) technology is introduced in order to automatically optimize the controlling law for quadrotors with different CGPs, and the CGPs are used to extend the RL state list. A deterministic policy gradient (DPG) algorithm that is based on an actor-critic structure in a model-free style is used as the learning algorithm. Mirror sampling and reward shaping methods are designed in order to eliminate the steady-state errors of the RL controller and accelerate the training process. Active disturbance rejection control (ADRC) is applied to reject unknown external disturbances. A set of extended state observers (ESOs) is designed to estimate the total disturbance to the roll and pitch axes. The covariance matrix adaptation evolution strategy (CMA-ES) algorithm is used to automatically tune the ESO parameters and improve the final performance. The complete controller is tested on an F550 quadrotor in both simulation and real flight environments. The quadrotor can hover and move around stably and accurately in the air, even with a severe disturbance. Full article

A Linear Fresnel Reflector (LFR) is a recent technology with good potential in small-scale solar power applications. It is composed of many long rows of mirrors that focus the sunlight onto a fixed elevated tubular receiver. Mirror segments are aligned horizontally and track the sun such that the receiver does not need to be moved. The efficiency with which the LFR can convert solar to thermal energy depends on the accuracy of the sun tracking system. To maximize the degree of sunlight capture, precise solar tracking is needed so that incident solar rays can be adequately focused to the focal point given by the location of the tubular receiver. The tilt angles of each row are relevant for the tracking controller to achieve correct positioning. Encoders are generally employed in closed-loop tracking systems as feedback signals used to inform the controller with the actual position of collector mirrors. Recently, inclinometers have begun to replace encoders as the most viable and cost-effective sensor technology solution; they offer simpler and more precise feedback, as they measure the angle of tilt with respect to gravity and provide the ability to adjust the system to the optimal angle for maximum output. This paper presents the research results on the development of remote measurements for the precise control of an LFR tracking system, by using distributed angle measurements. The applied methodology enables precision measurement LFR inclination angles through the fusion of data from multiple accelerometers, supported by low-cost wireless transceivers in a wireless sensor network, capable of exchanging information in a cloud infrastructure. Full article

Urban remote sensing with moving carriers enables comprehensive monitoring of an urban area. High spatial resolution and wide covering are always required to improve the performance and efficiency of remote sensing. Continuous scanning imaging is a feasible solution. However, imaging motion degrades the performance of a remote sensing system. Rotating motion leads to the loss of key urban morphology information of a panorama imaging. Image translation results in blurry images. For high spatial resolution and high efficiency imaging with low illumination condition, such as imaging at dusk, long-focus lens and long integral time must be further utilized, which makes the problem more severe. In this paper, a novel image motion compensation method is proposed to compensate for image rotation and image translation simultaneously. A quantitative description of image motion, including both image rotation and image translation, is first developed based on the principle of geometrical optics and then analyzed in detail through numerical simulations. Furthermore, a comprehensive image rotation compensation method is developed based on four-channel bilateral control with sliding mode controller, at the same time image translation compensation is performed according to the quantitative relationship of the motion of the scan mirror and image translation compensator. The experimental results show that the proposed method provides effective compensation for image rotation and image translation. This enables acquisition of high spatial resolution urban panoramic images. Full article