Search Results (227)

Electrostriction is an intriguing behaviour of dielectric materials, characterized by stable electrostrain with minimal hysteresis. (Na_0.5Bi_0.5)TiO₃-based ceramics show promising electrostrictive behaviour, particularly the 0.90(Na_0.5Bi_0.5)TiO₃-0.08KNbO₃-0.02SrTiO₃ composition located near the morphotropic phase boundary between ferroelectric rhombohedral and relaxor pseudocubic phases. The templated grain growth method has been effectively used to control the grain orientation of NBT-based systems, thereby enhancing their electrical properties. In this study, texturing was introduced to 0.90(Na_0.5Bi_0.5)TiO₃-0.08KNbO₃-0.02SrTiO₃ ceramics through homoepitaxial NBT platelets prepared via a three-step molten salt/topochemical microcrystal conversion method. By adding 4 wt% of NBT platelets combined with optimized sintering conditions, textured ceramics were prepared exhibiting a high Lotgering factor of 83% with enhancement of strain (0.02%) and polarization (3 µC/cm²) at an electric field of 40 kV/cm, as well as stable dielectric permittivity between 130 and 300 °C. Moreover, the electrostrictive coefficient of textured ceramics increased by ~0.004 C²m⁻⁴ compared to that of untextured ceramics, confirming the improvement of the electrostrictive response. These results demonstrate that homoepitaxial templating effectively improves the electrical properties of NBT-KN-ST ceramics while preserving their electrostrictive nature, which offers a viable route for designing lead-free electrostrictive materials. Full article

Studying the luminescent properties and the light amplification capabilities are fundamental investigations for newly synthesized organic compounds intended to act as chromophores. These studies are conducted for compounds in the form of solutions, solids, and also molecules stabilized with the aid of polymers. One of the methods used to study amplification is the generation of amplified spontaneous emission (ASE) using stripe-shaped light beam excitation. This process can lead to the generation of ASE, but also, with the coexistence of microcrystals and scatterers, to the generation of laser action with random feedback, known as random lasing (RL). However, when the degree of light scattering is too high, it can lead to the inhibition of laser emission. Therefore, as an alternative in studying amplification properties, we developed a protocol that allows the investigation of laser action generation using rapidly prototyped polymer waveguides with an embedded dye. The setup used was based on Direct Laser Writing (DLW), which enables the controlled fabrication of multimode optical waveguides. We demonstrated that the use of this technique will allow for the study of the performance of dyes from strictly structured resonators, enabling measurements of gain and lasing threshold. This allowed us to lower the lasing thresholds while maintaining the directionality of emission. Full article

The development of serial crystallography (SX), including serial synchrotron crystallography (SSX) at synchrotron sources and serial femtosecond crystallography (SFX) at X-ray free-electron lasers (XFELs), has facilitated the collection of high-resolution diffraction data from micron-sized crystals, providing unique insights into the structures and dynamics of biomolecules at room temperature. Standard samples are essential for the commissioning of new XFEL instruments and the validation of experimental setups. In this review, we summarize currently used standard proteins and describe representative microcrystal preparation workflows for four widely adopted models, lysozyme, myoglobin, iq-mEmerald, and photoactive yellow protein (PYP), drawing on established methodologies and accumulated experience from their applications at the European XFEL. By consolidating existing knowledge and integrating protocols that have been systematically refined and optimized through our experimental efforts, this review aims to provide practical guidance for the serial crystallography community, thereby enhancing reproducibility and ensuring consistent experimental performance across facilities. Full article

The escalating global challenge of waste production underscores the urgency for innovative waste management solutions. Sewage sludge, a byproduct derived from anaerobic digesters of wastewater treatment, was investigated as a flame-retardant synergist in Poly(Lactic Acid) (PLA). Micronized sludge was combined with ammonium polyphosphate (APP) at different ratios. The formulation containing (4:1) APP:Sludge exhibited enhanced flame retardancy compared to APP alone, achieving higher Limiting Oxygen Index (LOI) values and a V-0 rating in the UL-94 test. Cone calorimeter analysis further confirmed that the sludge contributed to reducing heat release and smoke generation. SEM–EDS analysis indicated that microcrystals, mainly composed of phosphorus and calcium oxides from APP and sludge, likely acted as protective barriers against heat transfer. In addition, filament extrusion demonstrated that sludge incorporation is compatible with 3D printing. This approach preserved structural integrity, sustainably utilized sewage sludge, and reduced reliance on commercial flame retardants. Integrating sludge as a synergist offers a promising solution for waste management and safer, more sustainable flame-retardant materials, supporting a circular economy. Full article

A high-surface-area activated carbon material (RG) is used as a platform to create highly concentrated NaOH composites. These materials are tested for the removal of H₂S under industrially relevant conditions (800 ppm H₂S in CO₂-, H₂O- and O₂-containing streams). The experimental results show that the breakthrough performance highly depends on the amount of NaOH incorporated and the experimental conditions used (e.g., relative humidity). The most promising material (RG-NaOH-30) reaches a saturation uptake of up to 800 mgH₂S/g at 25 °C and atmospheric pressure. This value is among the most promising results reported in the literature for H₂S removal, and it is well above traditional commercial samples. Breakthrough column tests confirm the promoting role of humidity in the reaction mechanism. Analysis of the adsorbents after H₂S confirms the formation of well-defined sulfur (S_n) microcrystals as the main reaction product. Full article

In this study, alkali-activated materials (AAMs) were developed using finely ground coral powder (CP) and granulated blast furnace slag (GBFS) as the primary raw materials, weak alkali as the activator, and sea sand as the fine aggregate. The influence of raw material composition on the macro-mechanical properties was analyzed. Further, combined with micro-analysis techniques, the characteristics of micro-crystal formation and transformation, governed by raw material properties, and the formation and development mechanism of the enhanced micro-gel structure were elucidated. The results indicate that the activation effect of Ca(OH)₂ is significantly superior to that of Na₂CO₃. The excessively high calcium content and insufficient silicon and aluminum content in CP hinder gel formation and mechanical properties development. GBFS addition optimized the calcium-silicon-aluminum ratio and significantly improved CP reactivity. Also, compressive strength is enhanced considerably, accompanied by continuous optimization of the micro-gel structure as the GBFS content increases. At a GBFS-to-CP optimal ratio of 1:1, compressive strength of 21.8 MPa could be achieved at 28 days of age. However, the strengthening effect significantly reduced for the GBFS content > 50%. GBFS promotes the continuous formation of a zeolite-like phase gel structure, leading to a substantial improvement in compressive strength. Full article

Poly(lactic acid) (PLA) holds significant promise as an option in the field of packaging materials due to its biodegradability and antibacterial properties. Therefore, it is vital for developing packaging materials while improving their heat resistance, and transparency is essential for guaranteeing its application. Using a self-assembled nucleating agent with hydrogen bonding and thermodynamically compatible transparent polymethyl methacrylate (PMMA), this study fabricated PLA micro-crystals with an interface blurred grain. Furthermore, the crystalline structure-property relationship was investigated in different isothermal crystallization conditions; it was possible to achieve higher crystallinity while maintaining the transparency of PLA/10 wt% PMMA/0.3 wt% nucleating agent blends. Compared to other temperatures, the crystallization rate of PLA blends under annealing conditions at 90 °C was higher when induced by three different nucleating agents. Particularly, in the presence of the TC-328 nucleating agent, the system exhibited a crystallinity of 32%, the smallest grain size, and an increased Tg of 61.3 °C, as well as an elevated heat deformation temperature (HDT) from 54.13 °C to 63.2 °C. The smaller nucleating agents with high surface energy enhanced the interaction between the PLA and PMMA, enhancing the PLA/PMMA tensile strength and HDT. These findings may pave the way for designing novel blends for packaging or heat-resistant devices. Full article

Lead halide perovskites (LHPs) have superior luminescent properties, but their toxicity hinders their commercialization, arousing interests in tin halide perovskites as environmentally friendly substitutes for LHPs. Herein, we synthesized a series of two-dimensional tin halide perovskite ODASnBr_4-xI_x (ODA denotes 1,8-octanediammonium, X = 0, 1, 2, 3, 4) microcrystals via an aqueous-phase method. The differences between ODASnI₄ and ODASnBr₄ in luminescent properties and morphological characteristics were systematically discussed for the first time and attributed to light-driven ligand-to-metal charge transfer. The prepared ODASnBr₄ has a PL peak at 567 nm and a PL QY of 99%, and the white light-emitting diodes fabricated with ODASnBr₄ and commercial blue phosphors realized a luminous efficacy of up to 96.27 lm/W, which demonstrated the remarkable potential of ODASnBr₄ microcrystals for high-efficiency white light-emitting diode applications. Full article

AgCl microcrystals are used in visible light photocatalysis. However, their properties depend strongly on the morphology of the crystals and the degree of exposure of the crystal planes. Despite extensive research conducted on the synthesis of AgCl microcrystals, the majority of existing studies have focused on the stable growth of crystals. The role of Cl⁻ ions concentration as a key factor controlling the microcrystals morphology has not been fully explored, which limits the precise tuning of the morphology of AgCl microcrystals. In this study, AgCl microcrystals with controllable morphology are successfully synthesized by a facile solvothermal method. During the preparation process, ethylene glycol (EG) is utilized as a solvent, while polyvinylpyrrolidone (PVP) is employed as a surfactant. We systematically investigate the etching mechanism of AgCl microcrystals by analyzing the effect of sodium chloride (NaCl) concentration on their morphology. This investigation involves the integration of diverse characterization methods, including scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), and geometrical struc-ture analysis. The results demonstrate that Cl⁻ functions as both a surfactant, thereby promoting the nucleation of cubic microcrystals, and as an etchant, selectively etching the crystal surface. The order of selective etching on the crystal surface follows (100) planes > (110) planes > (111) planes. Based on this new mechanism, AgCl microcrystals with various morphologies, such as cube, octopod and dendrite, are successfully prepared, which provides a new idea for the precise design of noble metal halide microcrystals. Full article

Background/Objectives: Under physiological conditions, vascular smooth muscle cells (VSMCs) are in a quiescent contractile state, but under pathological conditions, such as atherosclerosis, they change their phenotype to synthetic, characterized by increased proliferation, migration, and production of an extracellular matrix. Furthermore, VSMCs can undergo calcification, switching to an osteoblast-like phenotype, contributing to plaque instability. Methods: In this study, we analyzed the phenotypic changes in VSMCs during the transition from a physiological to a pathological state, a key process in the progression of atherosclerosis, using confocal and transmission electron microscopy, real-time PCR, and intracellular calcium quantification. Results: Confocal and transmission electron microscopy revealed a prominent remodeling of the actin cytoskeleton, increasing autophagic vacuoles in synthetic VSMCs and the deposition of calcium microcrystals in calcified cells. Immunofluorescence analysis revealed differential expression of α-SMA (contractile marker) and galectin-3 (synthetic marker), confirming the phenotypic changes. Real-time PCR further validated these changes, showing upregulation of RUNX-2, a marker of osteogenic transition, in calcified VSMCs. Conclusions: This study highlights the dynamic plasticity of VSMCs and their role in atherosclerosis progression. Understanding the characteristics of these phenotypic transitions can help develop targeted therapies to mitigate vascular calcification and plaque instability, potentially countering cardiovascular disease. Full article

Serial crystallography is a rapidly advancing experimental technology that has seen significant development in recent years. This technique enables the continuous delivery of a series of protein crystal samples to the X-ray beam, allowing for the collection of diffraction data from a large number of crystals at ambient temperature. Despite its advancements, serial crystallography still possesses considerable potential for further development within synchrotron radiation platforms. Currently, several challenges hinder the progress of this technology, including the preparation of numerous microcrystal samples, methods for sample delivery, data acquisition efficiency, and data processing techniques. The device introduced in this paper is designed to facilitate serial crystallographic experiments at the synchrotron radiation station, employing electrospinning in the vacuum cavity to reduce the average flux, mitigate the effects of air ionization on the Taylor cone, and enhance the stability of Taylor cone during the data acquisition process. The diffraction pattern of lysozyme crystals was successfully acquired with this device at the beamlines of the Shanghai Synchrotron Radiation Facility (SSRF). Full article

Crystalline lanthanide terephthalates, Ln₂bdc₃‧nH₂O (Ln = La–Lu, excluding Pm), were synthesized using a surfactant-free, ultrasound-assisted method. This approach yielded microcrystals with diverse shapes and sizes ranging from 2 to 10 μm. Notably, under these conditions, lutetium terephthalate uniquely crystallized as Lu₂(1,4-bdc)₃·2.5H₂O, while the remaining lanthanides formed tetrahydrate terephthalates, Ln₂bdc₃‧4H₂O (Ln = La–Nd, Sm–Yb). Full article

We previously found that host–guest interactions can drive gingerols (Gs) and cyclodextrins (CDs) together to form inclusion complexes (G/CD), which can further construct amphiphilic microcrystals and resultant Pickering emulsions through self-assembly. In this follow-up study, we explored the detailed formation processes and mechanisms of the 6-G/β-CD inclusion complex and the resultant Pickering emulsion. The influence of the 6-G/β-CD molar ratio on the structure, morphology, and loading capacity of the inclusion complex and resultant Pickering emulsion were investigated. The results show that the cyclodextrin-based Pickering emulsion can load 6-G in two places; one place is the cyclodextrin cavity, whose loading capacity is up to 9.28%, while the other one is the Pickering core, with its highest loading capacity at 32.31% when the 6-G/β-CD molar ratio is 5:1. In the above case, the 6-G/β-CD inclusion complex was found to form a unit cell with a 1:2 molar ratio and then self-assemble into amphiphilic microcrystals through cage-type arrangement structures at the oil–water interface, mainly driven by van der Waals forces and hydrogen bonds. This study is helpful in the design and preparation of CD-based high-loading carriers for bioactive compound delivery. Full article

Serial femtosecond crystallography (SFX) using X-ray free-electron lasers (XFELs) enables the determination of biological and chemical structures without radiation damage. In SFX experiments, a sample delivery system is essential for delivering numerous crystals to the X-ray interaction point in a serial and stable manner. Among the various sample delivery methods, the fixed-target (FT) sample delivery system is straightforward and widely used for collecting SFX data due to its advantages of low sample consumption and reduced physical damage to crystals during data collection. Here, we review the development of the FT sample delivery system for SFX with the Pohang Accelerator Laboratory X-ray free-electron laser (PAL-XFEL). The specifications and operational conditions of the FT-SFX sample chamber are described. The design, specifications, and applications of the one- and two-dimensional FT sample holders developed for SFX with the PAL-XFEL are also detailed. Furthermore, the applications of each FT sample delivery system are discussed. This review not only provides valuable information on the FT system used in SFX experiments with the PAL-XFEL but also offers insights into the development of FT sample delivery systems. Full article

Serial crystallography (SX) determines the crystal structures of target molecules at room temperature with minimal radiation damage. During SX data collection, the stable delivery of many microcrystals to the X-ray interaction point is crucial for efficient sample consumption and effective beamtime usage. Most microcrystal delivery techniques for SX require sophisticated devices or specialized techniques, which can be challenging for data collection. This review introduces a straightforward method that delivers microcrystal samples in SX experiments using a commercially available syringe and syringe pump. This method does not require specialized skills for sample delivery and can be tested in the laboratory prior to SX data collection at the beamline. Advantages and disadvantages of this method are also discussed, along with various application cases. This straightforward sample delivery approach is concluded to facilitate efficient SX data collection. Full article