Search Results (5)

Liquid electrolytes in conventional lithium-ion batteries pose safety risks associated with flammability, leakage, and explosion, whereas solid polymer electrolytes are generally limited by insufficient ionic conductivity at ambient temperature, restricting the development of high-energy lithium batteries. To address these issues, flexible poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP)-based gel polymer electrolyte membranes (GPEs) were prepared via a slit-coating process combined with UV curing. NASICON-type lithium aluminum titanium phosphate (Li_1.3Al_0.3Ti_1.7P₃O₁₂, LATP) and garnet-type tantalum-doped lithium lanthanum zirconate (Li_6.4La₃Zr_1.4Ta_0.6O₁₂, LLZTO) were introduced as inorganic ceramic fillers to improve the ion-transport and interfacial properties of the GPE. Among the investigated samples, the PVDF-HFP-based GPE containing 10 wt% LLZTO exhibited the best overall performance, with an ionic conductivity of 3.40 × 10⁻⁴ S·cm⁻¹ at ambient temperature and a Li⁺ transference number of 0.77. Cyclic voltammetry results showed that the LLZTO-modified electrolyte membrane exhibited sharper and more symmetric redox peaks, higher peak current response, and better curve overlap during repeated cycles, indicating improved electrochemical reversibility and interfacial stability. In addition, LLZTO incorporation enhanced the mechanical strength, broadened the electrochemical stability window, and improved the flame-retardant behavior of the membrane. The LiFePO₄/GPE/Li cell assembled with the optimized membrane delivered an initial discharge capacity of 160 mAh·g⁻¹ at 0.1 C and maintained 80 mAh·g⁻¹ at 1 C, demonstrating good rate capability. Moreover, a capacity retention of 96% was maintained after 100 cycles at 0.1 C, confirming excellent cycling stability. Therefore, this work provides an effective strategy for the structural optimization and scalable preparation of high-performance gel polymer electrolyte membranes for lithium battery applications. Full article

At present, lithium lanthanum zirconate (LLZO) is regarded as one of the most promising solid-state electrolyte materials due to its high ionic conductivity (about 10⁻³ S/cm at room temperature), high chemical stability, and excellent chemical stability toward cathode materials and lithium metal anodes. However, there are several problems, such as poor interface contact with the lithium metal anode resulting in high interface impedance, a high sintering densification temperature (usually >1200 °C), a complex preparation process, and high cost. In recent years, researchers have conducted extensive studies on LLZO and achieved remarkable progress and results. This paper systematically reviews the research progress of LLZO’s structural characteristics, conductive mechanism, preparation methods, improvement strategies, and so on. Full article

Lithium-ion batteries (LIBs) have significantly advanced portable electronics, yet their reliance on flammable organic solvents and lithium dendrite formation pose safety risks. Solid-state batteries (SSBs), utilizing solid electrolytes, offer a safer alternative with higher energy and power densities. This study explores the fabrication of solid electrolytes using ceramic stereolithography, focusing on lithium lanthanum zirconate (LLZ) due to its high ionic conductivity and chemical stability. A photosensitive paste containing 40–43 vol% LLZ was suitable for processing by stereolithography, and optimized processing parameters of 100 mW laser power and 1000 mm/s laser scanning speed with a 50 μm laser spot size were identified for sufficient material curing and interlayer lamination of LLZ. Thin embossed sheets were designed to enhance ion exchange and reduce internal resistance and were fabricated by the ceramic stereolithography method. The effect of cold isostatic pressing (CIP) on the sintered microstructure was investigated, and the potential for CIP to promote solid-phase diffusion during sintering was demonstrated, particularly at 67 MPa. The resulting LLZ-embossed sheets exhibited dense ceramic microstructures. These findings support the potential application of ceramic stereolithography for fabricating efficient solid electrolytes for next-generation telecommunications and mobile devices. Full article

Numerous endeavors have been dedicated to the development of composite polymer electrolyte (CPE) membranes for all-solid-state batteries (SSBs). However, insufficient ionic conductivity and mechanical properties still pose great challenges in practical applications. In this study, a flexible composite electrolyte membrane (FCPE) with fast ion transport channels was prepared using a phase conversion process combined with in situ polymerization. The polyvinylidene fluoride-hexafluoro propylene (PVDF-HFP) polymer matrix incorporated with lithium lanthanum zirconate (LLZTO) formed a 3D net-like structure, and the in situ polymerized polyvinyl ethylene carbonate (PVEC) enhanced the interface connection. This 3D network, with multiple rapid pathways for Li⁺ that effectively control Li⁺ flux, led to uniform lithium deposition. Moreover, the symmetrical lithium cells that used FCPE exhibited high stability after 1200 h of cycling at 0.1 mA cm⁻². Specifically, all-solid-state lithium batteries coupled with LiFePO₄ cathodes can stably cycle for over 100 cycles at room temperature with high Coulombic efficiencies. Furthermore, after 100 cycles, the infrared spectrum shows that the structure of FCPE remains stable. This work demonstrates a novel insight for designing a flexible composite electrolyte for highly safe SSBs. Full article

A spray-flame reaction step followed by a short 1-h sintering step under O₂ atmosphere was used to synthesize nanocrystalline cubic Al-doped Li₇La₃Zr₂O₁₂ (LLZO). The as-synthesized nanoparticles from spray-flame synthesis consisted of the crystalline La₂Zr₂O₇ (LZO) pyrochlore phase while Li was present on the nanoparticles’ surface as amorphous carbonate. However, a short annealing step was sufficient to obtain phase pure cubic LLZO. To investigate whether the initial mixing of all cations is mandatory for synthesizing nanoparticulate cubic LLZO, we also synthesized Li free LZO and subsequently added different solid Li precursors before the annealing step. The resulting materials were all tetragonal LLZO (I4₁/acd) instead of the intended cubic phase, suggesting that an intimate intermixing of the Li precursor during the spray-flame synthesis is mandatory to form a nanoscale product. Based on these results, we propose a model to describe the spray-flame based synthesis process, considering the precipitation of LZO and the subsequent condensation of lithium carbonate on the particles’ surface. Full article