Search Results (5)

This paper addresses the need for an integrated approach to develop an improved clam dredge system. Current designs often rely on empirical methods, resulting in a disconnect between theoretical models, computational simulations, and experimental validation. To bridge this gap, the study integrates computational fluid dynamics (CFD), experimental tests, and analytical methods to develop a clam dredge system. Firstly, the paper introduces an analytical tool that facilitates decision making by evaluating pump parameters, and to determine the operating point for various hose and nozzle parameters. This guides the parameter selection of pump, hose and jets for maximum performance. Secondly, CFD is utilized to analyze flow behavior, enabling the design of internal nozzle geometries that minimize head losses and maximize the scouring effect. A full-scale experimental measurement was conducted to validate computational results. Furthermore, a replica manifold is constructed using 3D printing and tested, demonstrating improvements in jet speed with both original and new nozzle designs. Analytical results indicate that increasing hose length reduces BHP, flow rate, and jet velocity, while increasing hose or jet diameter boosts BHP and flow but reduces jet speed due to pressure drops. Switching pumps reduced power consumption by 10.5% with minimal speed loss. The CFD analysis optimized nozzle design, reducing jet loss and enhancing efficiency. The proposed slit nozzle design reduces the loss coefficient by 85.24% in small-scale runs and by 83% in full-scale runs compared to the original circular jet design. The experiments confirmed the pressure differences between the CFD and experimental tests are within 10%, and demonstrated that rectangular jets increase speed by 9% and seafloor force by 19%. This paper improved the hydrodynamic design of the clam dredge system, and provides a framework for future dredge system designs. Full article

Piston top rings in the combustion engine play a crucial role in the overall hydrodynamic performance of engines, such as power loss, minimum film thickness and friction forces, by ensuring sealing and minimizing the leakage of burnt gases. This present paper examines the influence of four key parameters of the top ring, such as ring width, ring temperature, ring tension, and ring surface roughness on the hydrodynamic behavior at the ring/cylinder contact. These parameters play a significant role in the formation and maintenance of the oil film, directly influencing hydrodynamic indicators such as the minimum oil film thickness, friction force, power loss, oil pressure, and the ring angle twist. This article relies on hydrodynamic models and numerical simulations performed using GT-SUITE version 6 software to analyze these effects. The pressure curve used in this simulation is experimentally validated for an engine speed of 2000 RPM. It was found that an increase in the top ring temperature reduces the oil’s viscosity, decreasing the film thickness and increasing the risk of metal-to-metal contact. Increasing the roughness of the ring enhances oil film stability, especially at the bottom dead center (BDC) points during each phase of the operating cycle. Further, three different types of ring profiles were investigated for friction forces by varying the speed of the engine. Full article

Reducing friction losses is one of the most common ways to improve fluid film bearings, whose adjustable design provides additional opportunities to improve their dynamic and tribological properties. Previous studies have shown the possibility of reducing viscous friction in actively lubricated bearings by adjusting the rotor position. This work provides a theoretical justification for the mechanism of this effect for the cases of purely laminar lubricant flows in journal bearings. The operating modes connected with the transition to turbulent phenomena and the occurrence of Taylor vortices are beyond the scope of this paper. Conditions that ensure the minimization of friction losses in hydrodynamic and hybrid bearings with hydrostatic parts are determined based on the equations describing viscous friction in a fluid film. In non-adjustable plain hydrodynamic bearings, the minimum of friction is achieved with the centered shaft position that is actually unstable due to the resulting forces configuration. In actively lubricated hybrid bearings, a further reduction in viscous friction is possible by combining film thickness and pressure distributions. Recombining them, along with adjustment of the shaft position, allows the optimization of the distribution of shear stresses in the fluid film. As a result, the shear stresses caused by the rotation of the shaft can be partially compensated by the stresses caused by the pressure gradient, reducing the torque-resisting rotation. In addition, additional benefits can be obtained in the minimum friction state by the reduced lubricant flow and power losses to its pumping. A series of numerical calculations for elliptical, 3-, and 4-lobe bearings show that non-circular bores provide additional variability in film thickness distribution and a premise for optimizing the bearing tribological parameters. Four-lobe bearing demonstrated the best ability for reducing viscous friction among the considered designs. The results obtained can be used as a basis for further optimization of the geometry of fluid film bearings of both active and passive designs by reducing power losses due to viscous friction. Full article

Fin arrays are widely utilized in many engineering applications, such as heat exchangers and micro-post reactors, for higher level of fluid–solid contacts. However, high fluid pressure loss is reportedly the major drawback of fin arrays and a challenge for pumping supply, particularly at micro-scales. Previous studies also indicate that fin shapes, spacing and alignment play an important role on the overall pressure losses. Therefore, we present a numerical tool to minimize pressure losses, considering the geometrical aspects related to fin arrays. In this regard, a density-based topology optimization approach is developed based on the pseudo-spectral scheme and Brinkman penalization in 2D periodic domains. Discrete sensitives are derived analytically and computed at relatively low cost using a factorization technique. We study different test cases to demonstrate the flexibility, robustness and accuracy of the present tool. In-line and staggered arrays are considered at various Reynolds numbers and fluid–solid volume fractions. The optimal topologies interestingly indicate a pressure loss reduction of nearly $53.6\%$ compared to circular fins. In passive optimization test examples, the added solid parts reduced pressure loss of a circular fin ( $9\%$ ) by eliminating the flow separation and filling the wake region. Full article

The environmental impact of many industrial and naval applications is becoming increasingly important. Journal bearings are crucial components related with the reliable, safe and environmentally friendly operation of rotating machinery in many applications, e.g., in hydroplants, ships, power generation stations. The maintenance activities in certain cases also have considerable environmental impact. Fortunately, it is relatively easy to reduce the impact by changing the way lubricants are being used. Selecting the proper lubricant is important to sharply reduce long-term costs. The best-fit product selection can mean longer lubricant life, reduced machine wear, reduced incipient power losses and improved safety. Suitable basestocks and additives reduce environmental impact. In this paper, three types of lubricants are used in order to examine their effects on the tribological behavior of journal bearings. A mineral oil, a synthetic oil and a bio-based lubricant are experimentally and analytically examined for several configurations of load and journal rotational velocity. The friction forces and the hydrodynamic friction coefficients are calculated and compared. This investigation can assist the correct choice of lubricant in journal bearings with minimized environmental footprint. Full article